Not Doing This Will 100% BLOW Your Ski-Doo Snowmobile Engine!

Поделиться
HTML-код
  • Опубликовано: 22 дек 2024

Комментарии • 118

  • @Buildcultureyoutube
    @Buildcultureyoutube  2 года назад +7

    Forgot to add*
    For the water trick: the sled needs to be on it’s side obviously so the water doesn’t just pour out

  • @raykultgen3125
    @raykultgen3125 2 года назад +4

    There is isoflex on the mag side also, done thru stator screws, later models have it in the inner bearings as well.

    • @Buildcultureyoutube
      @Buildcultureyoutube  2 года назад

      Yes forgot to mention that! This side wears faster because of heat

    • @draymond5067
      @draymond5067 Год назад +1

      @Build Culture no, PTO side wears faster due to the belt load...most bearing failure on pto side....it's the opposite on seadoo's

  • @Junorr500
    @Junorr500 Год назад +4

    Do a leak down test on that seal after you do this. If seal is bad you need to pull motor and pull off bottom of crankcase to properly install a new brand new seal. A new one will not push in without wrecking it.

    • @skidooman97
      @skidooman97 Год назад

      How do u preform this test @Junorr500. I did this job about 1500miles ago and now i noticed coolant seeping out of bottom end headgasket .

    • @Junorr500
      @Junorr500 Год назад +1

      @@skidooman97 leaking coolant is a whole different issue. Sounds like time to tear out motor and do all new gaskets. May as well split bottom end case to reseal it and do oil seals to.

    • @Junorr500
      @Junorr500 Год назад +2

      @@skidooman97 to do leak down test you need to pressurize the crank case. I take carbs off and fit a plug with a schrader valve and a gauge threaded into it and clamp it into carb boot. Pressuize it with 10lb is plenty and watch the gauge. If it drops you have a problem. My clutch side crank seal was leaking. Can see it if you use soap and water and spray it on seal where crank comes through. Will make bubbles. To make this work though you need to seal exhaust as well. Remove y pipe and make a cover/gasket for exaust and secure it but bolting y pipe back on.

  • @alvarezz09
    @alvarezz09 10 месяцев назад +1

    Great video! i do this every year too all my sleds just incase behind the first set of bearings there is another set behind.

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      it is not a maintenance procedure,not recomended,nor neccesary

  • @anonymous-tn6ij
    @anonymous-tn6ij Год назад +1

    What about the big crack in the casting outside the bearing 3 o’clock position

    • @Buildcultureyoutube
      @Buildcultureyoutube  Год назад +2

      I believe that’s where the 2 pieces of the case meet. I can see how it can look like a crack now that I look at it lol

    • @GWAYGWAY1
      @GWAYGWAY1 Год назад +1

      That IS the crankcases face joints. It split horizontally.

  • @davidwright1653
    @davidwright1653 Год назад

    Why not use a solvent or brake clean to remove the old grease from the bearing? Is the Isoflex the manufacturer's recommended grease? Or one you believe is better? The syringe method is very useful, is wearing nitrile gloves and packing the grease with your fingers not as effective? Thank you for this video!

    • @Buildcultureyoutube
      @Buildcultureyoutube  Год назад

      Idk it just felt wrong at the time. But others here have said it’s not an issue. Just did what I thought was best.
      And the syringe seemed like a very effective method to get it all into the crevices and squeeze out as much old brown grease as possible. Worked quite well.
      As far as I know that exact isoflex grease is exactly what is used from OEM. It is pricey though.

    • @davidwright1653
      @davidwright1653 Год назад

      @@Buildcultureyoutube Thank you!

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      not a maintenance procedure,not neccesary,not recomended, overgreasing causes heat and failure.

  • @olivermeier2949
    @olivermeier2949 Год назад +7

    They couldn't just run an oil line to the bearing for priority lubrication? After all,it is the crank. Cool engineering BRP.

  • @WolfLakeCreek
    @WolfLakeCreek Год назад

    Nicely done! I am wondering, did you replace the old fuel hoses simply because they were to old an dirty, or do
    the new ones have a bigger diameter? Or they just much better? Regards Tobias/Sweden

    • @Buildcultureyoutube
      @Buildcultureyoutube  Год назад

      Hi thanks for watching! I don’t believe I changed the fuel hoses on that sled unless maybe I’m forgetting something? I usually just replace stuff that looks old without thinking much lol. But this specifically I do not remember

  • @justinc8638
    @justinc8638 Год назад

    Great video does this apply on a 2015 MXZ x 800R ecotec? Thanks

    • @Buildcultureyoutube
      @Buildcultureyoutube  Год назад

      I wouldn’t want to give you the wrong answer but hopefully someone knowledgeable can chime in!

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      this is not a maintenace procedure,not reccomended , not required, over greasing is a sure failure

  • @36ELGALAN
    @36ELGALAN Год назад +2

    Great video, nice trick with the Syringe

    • @xXkillerkidXxXx
      @xXkillerkidXxXx Год назад

      You need the syringe... shop manual even says so, should only have so many ML in the bearing

  • @darrrenbetker4266
    @darrrenbetker4266 Год назад

    Wh6 would u not use brale clean?

    • @Buildcultureyoutube
      @Buildcultureyoutube  Год назад

      Was worried about it messing with the new lubricant

    • @c90adventures
      @c90adventures Год назад

      I can confirm that isoflex grease doesn't dissolve in either brake cleaner or isopropyl alcohol.
      I did a test by taking some of the old grease and putting it in containers with liquids. The only thing that dissolved it was WD-40.
      Other solvents I don't have might work as well of course.

    • @Buildcultureyoutube
      @Buildcultureyoutube  Год назад

      Nice!

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      @@c90adventures It is life of the bearing grease does not dry up does not dissappear overgreasing causes failures. no required or a neccesary maintenance

  • @davidbrennan5
    @davidbrennan5 Год назад +1

    There is a 1/4 inch pipe with a red cap on it behind the clutch on the crankcase to grease the pto bearings. Just add some grease every 2000-3000 miles. The other side is much more difficult, you have to take off the recoil pull the flywheel and add grease through the top stator bolt hole after removing one of the bottom stator bolts. That side needs to be greased, but not as often. The best way is to pull the engine and split the cases though.

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      not a maintenance procedure nor neccesary

    • @davidbrennan5
      @davidbrennan5 4 дня назад

      I don't know anyone that didn't add grease that got more than 3k miles out of their crank. If you want your crank to last you grease it. This is a well known issue with these engines.

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      @@davidbrennan5 you can believe that if ya like. the grease does not just disappear.

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      @@davidbrennan5 i see them in the 4- 6 miles still running strong never been touched.

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      @@davidbrennan5 Blowing a belt and over revving takes out these cranks. or overrevving in general. the reason no warranty on a etec that has been overrevved.

  • @smc-shitmopedcrew1654
    @smc-shitmopedcrew1654 2 года назад

    how often should i do this?

    • @Buildcultureyoutube
      @Buildcultureyoutube  2 года назад

      Once a year is recommended. That being said, my sled has 6200 miles on it and I think this was the first time 😳

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      never it is not recomended

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      @@Buildcultureyoutube no it is not recomended ever. life of bearing grease

  • @stevenpringle7813
    @stevenpringle7813 2 года назад

    Do you know if this still applies to the 2023 600 EFI engines? Thanks

    • @Buildcultureyoutube
      @Buildcultureyoutube  2 года назад

      At this moment I don’t know, but hoping someone can chime in and help you answer this!

    • @ChillyWillYee
      @ChillyWillYee Месяц назад

      @@Buildcultureyoutube Yes it does on my 22 850 turbo

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      @@ChillyWillYee no grease in 850 bearings.

  • @wtfobiden
    @wtfobiden Год назад

    Good job

  • @davidr9651
    @davidr9651 Год назад +1

    I have seen 600SDI engines go 30,000 with ever being apart. Same Isoflex

    • @stevecampbell1811
      @stevecampbell1811 Год назад

      The 800's don't go that far without replacing Iso.

    • @draymond5067
      @draymond5067 Год назад +1

      @Steve Campbell true, about 10-12kms on an 800...but about the same as any 800

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      Yes agreed .This is not a required or neccesary procedure.not even recomend.
      life of bearing grease with precise amount in new bearings.

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      @@stevecampbell1811 wrong

  • @haydenrichardp3712
    @haydenrichardp3712 Год назад +1

    Don’t think the grease will stay white once it’s used.

  • @scp8412
    @scp8412 2 года назад +1

    great way to repack bearings!!

  • @kjellamundsen1463
    @kjellamundsen1463 Месяц назад

    Water trick. Why not just use grease?

    • @Buildcultureyoutube
      @Buildcultureyoutube  Месяц назад

      Sounds like a good idea too!

    • @Buildcultureyoutube
      @Buildcultureyoutube  Месяц назад +1

      Water is cheaper tho

    • @ChillyWillYee
      @ChillyWillYee Месяц назад +1

      @@Buildcultureyoutube i actually use just one pump of grease from the gun and pops right off on my 22 Freeride turbo. Great Video !!!%

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      grease is messy and you dont want lube on the taper. gresae will compress water does not.

  • @louieboe1164
    @louieboe1164 8 месяцев назад +1

    How can you blow up a motor
    Not true

  • @keltingr2612
    @keltingr2612 2 года назад +8

    Why did Ski Doo design the 800r this way? Whoever did should be fired immediately

    • @Buildcultureyoutube
      @Buildcultureyoutube  2 года назад

      What specifically?

    • @doughboy5840
      @doughboy5840 2 года назад

      @@Buildcultureyoutube he is referring to the isoflex grease design instead of using the two stroke oil like the new ones do

    • @nr5834
      @nr5834 Год назад +1

      You can thank the EPA constantly requiring tighter emissions. They stopped oiling to reduce emissions afaik. I'm aware they are now oiling the 850 again, but i think it uses so little oil they can keep their emissions in check.

    • @BlueRage
      @BlueRage Год назад +2

      ​@@BuildcultureyoutubeSupposed to be 15 ML not the whole 50 gram tube.

    • @jeffb8562
      @jeffb8562 10 месяцев назад

      You’ve obviously never worked on anything built in the last 20 years with an engine and efficiency in mind. Not grammatically correct but you know what I mean. They used to be simple. But they aren’t anymore.

  • @defmc1
    @defmc1 Год назад +1

    I thought everything about skidoo was good and Polaris bad? Guess not.

    • @ChillyWillYee
      @ChillyWillYee Месяц назад

      Polaris is a lot easier to work on. Good and bad issues with my 23 khaos boost and 22 freeride turbo

  • @mxr248
    @mxr248 11 месяцев назад

    Problem is you only did one side

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      neither side recommended or necessary

  • @tackdriverCA
    @tackdriverCA Год назад

    what a terrible design, I'm glad I've got the 850

    • @ChillyWillYee
      @ChillyWillYee Месяц назад

      850s same design unfortunately. Polaris has grease zerk for simplicity.

    • @tackdriverCA
      @tackdriverCA Месяц назад +1

      @ it’s actually not the same design, 850 has oiled crank from oil injector.

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      it is a great design and monkeys think it needs to have grease added but not at all. life of bearing grease

  • @Fishnfreak
    @Fishnfreak Год назад

    Coming from someone who knows nothing about snowmobiles, this video was useless bc you weren’t specific on what you were doing at all. What you took apart, where it’s located on the snowmobile, why you did what you did, or even what it’s called??? etc. Just got a new Skidoo and trying to learn how to properly maintain it.

    • @Buildcultureyoutube
      @Buildcultureyoutube  Год назад +2

      This was one of my first videos ever and I made it to help a friend but I did write it in the description.
      I’m very sorry Johnney. I’ll try to do better.

    • @planetofthederps4490
      @planetofthederps4490 11 месяцев назад +4

      ​@Buildcultureyoutube i wouldn't of even responded to such a dumb comment man..the vid was perfectly fine for what you was showing..if this person ☝️ cant see that this is the pto shaft side where the primary clutch mounts..then he shouldn't be working on his sled anyway..such a rude comment towards someone taking time to show how to grease a crank bearing 🤦‍♂️

    • @ChillyWillYee
      @ChillyWillYee Месяц назад

      @@Buildcultureyoutube You did Great, anyone that has ever owned a sled knows.

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      Never ever do this. it is not recomended,necessary, or required

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      @@planetofthederps4490 funniest comment yet he is showing something not recommended,required or necessary. excessive grease is probly why these cranks fail.

  • @MidnightPolaris800
    @MidnightPolaris800 11 месяцев назад

    Driving a skidoo will with 100% certainty blow your crank...most garbage pos designed cranks ever...but hey you use less oil right? 😂😂😂

  • @gerardjones7881
    @gerardjones7881 11 месяцев назад

    buy the proper tools .

    • @Buildcultureyoutube
      @Buildcultureyoutube  11 месяцев назад +1

      You can buy them for me!

    • @planetofthederps4490
      @planetofthederps4490 11 месяцев назад +3

      Looked like he got the job done just fine..you make a vid doing this and use the "proper" tools 👍

    • @BillNye-bj5vi
      @BillNye-bj5vi 4 дня назад

      water trick works better and safer than a puller.

  • @clarknawrocki9718
    @clarknawrocki9718 Год назад +3

    Just turning the engine on will blow up a ski doo don't believe me I have owned several ski doo snowmobiles go buy one don't forget the tow rope

    • @olivermeier2949
      @olivermeier2949 Год назад +2

      Me too,just like their Sea doo watercrafts,you get to know the BRP service department team on a first name basis.

    • @ChillyWillYee
      @ChillyWillYee Месяц назад

      @@olivermeier2949 Or you learn how to teardown and replace on your own real fast.I own a 23 Khaos boost and a 22 Freeride turbo and numerous of each in last 30yrs and polaris makes things a lot easier to work on for sure but have had problems with both. I have OCD though so after every trip I do thorough maintenance and inspection to make sure my buddies are always behind me. Ride hard break hard, regardless.