we're dealing with this issue. Our mechanic said to replace the rear tail light (which we did). something about corrosion. that seemed to fix it for a while but it's back again. I don't mind doing this as well... but I'm skeptical.
Have you came across brake issues with the 2012-2014 Nissan versa. The problem being the brake Master Cylinder. Where the owner would have to pump the brake pedal or apply a lot of force to bring the car to a stop.
What’s the hose right above the sensor? The one you went under to remove the sensor after removing the screws. I am dealing with this right now and I unhooked the hose and it had some blue fluid. Great video by the way.
I have a Nissan Versa SL 2012 1.6, the engine light not on, and doesn’t show any code ! But my car start hard and sometimes no power and a few times on the red light car was on but no move , so I change spark plugs and air filter and Air mass sensor, but still car doesn’t start easy on morning ! If you think I should change engine speed sensor!?
Hi Keeny, Nice video. My Nissan Sentra 2012, 2.0 CVT blowing the use when shifting to reverse. The Mechanic replaced the neutral safety switch. Still same problem. He said somewhere wiring is short circuit. How I can Check or replace the wiring harness. Any electrical diagram, so I can track the wiring. Please advise. Thanks
So what if this doesn't fix it? My PRND light is going off still and the car is jerking once or twice at a time when I stop still. We replaced this part (bought straight from Nissan) and changed the brake bulbs like they suggested and it's still not fixed. I have a 2019 Nissan Versa SV. It obviously has the POS CVT transmission in it.
Cost for garage to do this? I was quoted 400 up to totally replacing tranny 4000+ backup light was out. Replaced it and engine light went off. Not coke back on ever since.
We haven't reset the codes yet but I am not sure that it would still do all of this with a new part in it if it were fixed regardless of the code. I don't see a code issue making the car jerk with a new sensor put in it but I could be wrong. I'm more of a pessimist and I'm terrified that my car is having a different issue. It read the same code you had but I dunno.
I have a 2012 Nissan Versa and I can’t get the neutral safety sensor out I took out bolts and still hard to remove it stuck on the shaft. I can’t get to break free . Do you have any advice
You could try checking the sensor output, but it's quite involved. If you're getting a P0705 code, do a google search. There is a common problem with this sensor that can be caused by high resistance in the reverse lamp circuit. Nissan has a service bulletin out about it.
Hello, I need your help. Where can I find the gearbox for Nissan Versa 2013? If it is available in your country, I need the address and price if possible, thank you.
Hello. Did you solve your problem? Hope you were able to check stop lights from both sides, light bulbs and bad contacts moisture and rust can cause hell in your versa. That can also trigger a reverse neutral switch problem also.
I know it’s been a year or more, but I’ll relay my experience. For me, sometimes the car will make like a pop sounds and feel like it shifts positions shortly after coming to a stop. Also, sometimes it feels like it’s having trouble going into drive and like it takes a little more effort on the pedal to get her going.
Usually you get code p0705 but first you have to check the electrical wires, circuits, etc. because any problem with that can give you that code but not necessarily has to be the sensor...
Check your taillights for large or small amounts of moisture and your taillight sockets for corrosion and or pitting corrosion. This sensor is in the same circuit as the taillights. Oh yeah one more thing apply black caulking between the black taillight flange and the rear body to stop water from flowing between the flange and body.
I'm dealing with this issue right now. I greatly appreciate this video!
What is your issue? Did you fix it?
I want to say...Thank you!!! Very informative....you clearly show the procedures and very honest about your recommendation
we're dealing with this issue. Our mechanic said to replace the rear tail light (which we did). something about corrosion. that seemed to fix it for a while but it's back again. I don't mind doing this as well... but I'm skeptical.
Just go for it man.. I need to replace it as well😂
I replaced the light assembly with code p 101. This p705 is different. I am going to do these steps. It seems simple enough. Thank you.
Thank you for this video. Having this issue at this moment with my car. And it has 152,000 on the odometer.
Don't forget the taillights can get moisture in them and cause havock with this sensor and throw this same code.
Thank you so much buddy foe show me how to change it properly.
Have you came across brake issues with the 2012-2014 Nissan versa. The problem being the brake Master Cylinder. Where the owner would have to pump the brake pedal or apply a lot of force to bring the car to a stop.
Thank you! The driving school I work for has three Versas.
Thank you so much! I am going to try by myself. I appreciate you so much!
What’s the hose right above the sensor? The one you went under to remove the sensor after removing the screws. I am dealing with this right now and I unhooked the hose and it had some blue fluid.
Great video by the way.
I have a Nissan Versa SL 2012 1.6, the engine light not on, and doesn’t show any code ! But my car start hard and sometimes no power and a few times on the red light car was on but no move , so I change spark plugs and air filter and Air mass sensor, but still car doesn’t start easy on morning ! If you think I should change engine speed sensor!?
It’s probably it is I had the same situation
Hi Keeny, Nice video. My Nissan Sentra 2012, 2.0 CVT blowing the use when shifting to reverse. The Mechanic replaced the neutral safety switch. Still same problem. He said somewhere wiring is short circuit. How I can Check or replace the wiring harness. Any electrical diagram, so I can track the wiring. Please advise. Thanks
So what if this doesn't fix it? My PRND light is going off still and the car is jerking once or twice at a time when I stop still. We replaced this part (bought straight from Nissan) and changed the brake bulbs like they suggested and it's still not fixed. I have a 2019 Nissan Versa SV. It obviously has the POS CVT transmission in it.
Make sure when you put it back together the vehicle on park and flush the transmission fluid for new fluid
We have exact same problem did you get it fixed?
Cost for part?
Cost for garage to do this? I was quoted 400 up to totally replacing tranny 4000+ backup light was out. Replaced it and engine light went off. Not coke back on ever since.
Not come back on rather. Should I still replace that sensor?
Do you have a video showing the neutral safety switch replacement for the 2012 Rogue?
We haven't reset the codes yet but I am not sure that it would still do all of this with a new part in it if it were fixed regardless of the code. I don't see a code issue making the car jerk with a new sensor put in it but I could be wrong. I'm more of a pessimist and I'm terrified that my car is having a different issue. It read the same code you had but I dunno.
Did you ever figure out what was causing the jerking? Mine is doing that after replacing the neutral safety switch
Did anyone figure this out? Mine is also doing the jerking
I have a 2012 Nissan Versa and I can’t get the neutral safety sensor out I took out bolts and still hard to remove it stuck on the shaft. I can’t get to break free . Do you have any advice
Were you able to figure this out? I'm having the same problem.
Did you figure this out?
Thank you
Is this same location as on 2016 Sentra kus it’s the exact same sensor so I’m thinking it would be in exact same spot as your car
Good video
What was the car doing?
I tried to purchase it from the dealer but they wanted me to buy the whole assembly
eBay
Thank you!!
Hello I replaced the part and cleared the code. After 3 weeks the code came back any suggestions?
did you check the tail lights as someone told above?
Exact same thing happened to me. Were you able to figure out what was going on?
I got mine changed about 2 months ago. Now the Auto Zone finder thingy is saying it’s the same thing.
Kenny. What does it cost to buy that sensor or neutral safety switch? Hours worth of work or much less?
Amazon has it for $22 to $30.
It works for 2017 Nissan versa sv ???
En qué posición va el sensor todavía lo moví
Does it make your car light is the RPMs go up and down
My 2013 altima sl can't drive in drive or reverse position ..why
Yours is cvt,, check the oil
How much is that part is you buy it directly from Nissan ?
$122 at Nissan dealer
$120
Would be more easy if remove battery and plate.
I need help. It is stuck
When you get this code how do you know that it’s just the senor circuit and not something else wrong with the car
You could try checking the sensor output, but it's quite involved. If you're getting a P0705 code, do a google search. There is a common problem with this sensor that can be caused by high resistance in the reverse lamp circuit. Nissan has a service bulletin out about it.
Hello, I need your help. Where can I find the gearbox for Nissan Versa 2013? If it is available in your country, I need the address and price if possible, thank you.
I have a 2017 Nissan Versa
Would it be the same process. ?
Same, was it?
Is it works for 2017 Nissan versa 2017? ?
I’ve had to get 6 of these things and still messing up
Hello. Did you solve your problem? Hope you were able to check stop lights from both sides, light bulbs and bad contacts moisture and rust can cause hell in your versa. That can also trigger a reverse neutral switch problem also.
Lasted 1 year with no engine lights might need another one too check engine light with the same code
What were the symptoms that you had to replace it?
I know it’s been a year or more, but I’ll relay my experience. For me, sometimes the car will make like a pop sounds and feel like it shifts positions shortly after coming to a stop. Also, sometimes it feels like it’s having trouble going into drive and like it takes a little more effort on the pedal to get her going.
@TheJoemerk thanks. I pretty much have the same thing you're talking about. Did it fix the solution after the replacement?
@@jessietheaztecI haven’t gotten it fixed yet :/
How much was the part?
Amazon has it for $22 to $30.
You need a better camera.
How can you tell if it bad ?
Usually you get code p0705 but first you have to check the electrical wires, circuits, etc. because any problem with that can give you that code but not necessarily has to be the sensor...
My car popped up with 8 codes
Speak up can't hear ****
Yanni
I changed and still the code.
Check your taillights for large or small amounts of moisture and your taillight sockets for corrosion and or pitting corrosion. This sensor is in the same circuit as the taillights.
Oh yeah one more thing apply black caulking between the black taillight flange and the rear body to stop water from flowing between the flange and body.
Horrible video