How to Repair Small Areas of Plaster | Drywall Patching
HTML-код
- Опубликовано: 25 фев 2024
- Sam Ward demonstrates how to repair low-level plaster.
MORTAR MIX
• 4 x Sharp Sand
• 1 x Castle Cement
• Sika 1 Waterproofer
www.builderdepot.co.uk/sika-1...
___________________________________
For patching a plaster repair, a suitable mortar mix should ideally be compatible with the existing plaster in strength, porosity, and thermal expansion to avoid cracking or detachment.
A traditional mix often recommended for such repairs is a lime-based mortar due to its flexibility, breathability, and ability to accommodate minor movements within the building structure without cracking.
Lime-Based Mortar Mix
• Lime Putty: Pure, non-hydraulic lime putty is preferred for its flexibility and permeability.
It allows the repair to breathe, reducing the risk of trapped moisture, which can lead to damage.
• Aggregate: Fine sand is typically used as the aggregate in plaster repair mixes.
The sand should be clean, well-graded, and free from impurities.
The colour of the sand can be chosen to match the existing plaster colour.
• Mix Ratio: A standard mix ratio for lime mortar for plaster repairs is 1 part lime putty to 3 parts sand by volume.
However, this can be adjusted based on the specific requirements of the repair, such as the desired strength or finish.
Considerations
• Compatibility: Ensure the mortar mix is compatible with the existing plaster, especially if the building is historic.
In such cases, matching the original materials as closely as possible is essential.
• Application: Apply the mortar in thin layers, allowing sufficient drying time between layers.
This approach helps to prevent cracking and ensures a strong bond to the existing plaster.
• Curing: Lime mortar cures slowly and needs to be kept moist for several days after application to ensure proper carbonation and hardening.
Protect the repaired area from direct sunlight, wind, and rain during this period.
Alternative: Gypsum-Based Plaster
A gypsum-based plaster might be used for interior repairs, especially in modern constructions. It sets faster than lime mortar and can be easier to work with for minor patch repairs.
• Mix Ratio: Follow the manufacturer’s instructions for mixing, as ratios can vary.
• Application: This can be applied similarly to lime-based mortars but usually dries and sets much faster.
Final Note
For best results, especially on historic buildings or where the plaster plays a structural role, consulting with a professional conservator or a tradesperson experienced in traditional building techniques is advisable. They can offer guidance tailored to the specific type of plaster and conditions of your building.
==========================================
#plastering #diy #patching
📪 Newsletter: skill-builder.uk/signup
/ skillbuilder
/ skillbuilderchannel
/ skill_builder
/ skillbuilderuk
🔗 Skill Builder Link Tree: linktr.ee/skillbuilder
🛒 As an Amazon Associate, we earn from qualifying purchases
🎬 Video library: ruclips.net/user/skillbuilderc...
💧 We Support Charity Water: www.charitywater.org
◾ Out of respect to our sponsors and followers, we'll remove comments that do not follow expected standards of politeness and decency.
I always enjoy seeing someone who knows what they are doing.
Always like watching Sam, a safe pair of hands and hard to find a dynamic guy like this. 👏👏👏
An excellent video - not only is Sam highly skilled but also an excellent teacher.
Give that man a RUclips channel! Loads of top tips. A few days too late for me and my project but definitely one for next time, cheers!
Man who takes, pride in his job.
Great information on how to use equipment for plastering,,,,,i never cease learning,,,,,,,also wonderful tips ty so much
Nice job Sam 🙌🏽🧱👍🏽
Lovely job!
Can you do a video on the best way to fill small movement cracks so they never reappear.
Remove the surface, back to the substrate, 100mm either side of the crack. Use a metallic mesh fixed to the substrate; you can do this by drilling a 6mm hole, then use 2-3 40mm galvanised nails into the hole. Soak the substrate in SBR then while wet use a 5to1 cement render, and leave a couple millimetres to the surface; scratch the render with lines. When dry, coat in SBR, let dry then plaster over, leaving slightly proud. When the plaster is dry use a random orbital sander to smooth back with about 80 grit paper. You’ll never know it was there.
@@gdfggggg he said VIDEO . its better to see something once then hear about it 100 times
@@gdfggggg Thanks for your explanation. Very clear instructions.
The issue is finding tradesman who are willing to go to that level of perfection
cracking job
I see what you did there.
great stuff
Is this a re-upload or deja-vu?
Definitely seen it before
He’s just confident for a second time that he’s cured the problem
we saw this place before when it had mystery damp in the wall.
Or you saw it in a dreamy premonition.
Plastering is fun, if you do multiple small mixes & layer it up. Or do one and use some skill like this bloke just did.
way too big of a mix but waste is part of getting home by 5pm.
Would have just done a few small pot mixes to fill that myself, but would have spent all day on it alike.
Each to their own.
Its new to me. I couldn’t stand Roger so I stopped watching
Time will tell. Bring back James
Why don't you use gypsum?
He's a 100%✓ for what he is doing.
Why would you use a small trowel
Why use mortar rather than a gypsum based bonding coat? Heard it mention in the vid but no explanation. Cheers
I thought that. I'd of used bonding
A bonding coat won’t be waterproof. A sand/cement coat with a waterproofing additive will be.
@@gdfgggggi thought you'd use bonding for jobs like this?
@@tomalex4806 not on waterproofing jobs.
In a previous video they talked about this house suffering from damp. So this was above and beyond. My builder mate said to me (as im reno’ing atm) to S&C external walls, thistle internal. Gypsum doesn’t handle moisture well 👍
best I've seen
I thought Sam was going to scrim the top area before adding the plaster?
Bit of context on the use of the additive would be welcome
Welcome new guy. I was getting tired of Roger whinging about pipes
PVA might not be *technically* necessary, but can't see the harm in it, and no scrim tape on the angle beads, again, why not, takes literally 10 seconds, and massively reduces risk of cracking
Don’t use PVA on any damp issues as it re-emulsifies. SBR is the stuff. A quick SBR and cement 50/50 x2 coats on the wall, then a waterproofing additive (SBR or waterproofer) in the cement render is what I’d do. I’d probably add a render mesh as it’s so easy (if it’s on the van). SBR is a gift from the render gods.
you are so right. Why don't we have a National SBR day to celebrate this wonder product? I meet plasterers who have never used it. I also saw that B&Q were selling it for £45.00 for 5 ltrs
@@SkillBuilderI sleep with SBR under my pillow 😂
@@SkillBuildertoolstation 27.99
£18 in my local hardware store
First like
Looks like he's done this before.
He didn't put any scrim on the joint
Whisk! Think of the money you are saving at the gym!
WOW, that was so easy to do; why hire a PRO ? For the dummies out there, I'm being facetious.