I have a 01 maxima and the bolts are the same 14mm and 17mm I'm changing my starter today thanks! I didn't know where my starter was...now I know. I just bought my max a year ago and I'm putting all new parts on it today! new alternator new battery and starter!
When you started your Maxima made that extended noise kind of a grinding sound after it started for a couple seconds. Mine is doing that same thing but maybe a little worse. I was thinking it might be my starter going out. My starter is still working fine but I don't want to replace it if that is not the cause of that sound. I'm also getting code p1320. Any suggestions?
Jose Tapia I bought mine at O Riley's auto parts. Just the pod filter, the assembly was bought on Amazon. If you wanted links to purchase them let me know. Also, if you wanted to hear how she sounds please watch my 0-60 and reaches 285k mile video. It's my most recent video. Thank you.
That's what I'm dealing with now on 2000 Sentra 1.8. The bindix goes forward but will not turn. After 3 days of working fine, then a couple days of starting with a little bit of grinding noise at first. Think I should shim it?
Hey, sorry for the late reply. Car was starting great since I've replaced it. Sadly she went to the scrap yard 3 years ago. I have a current 05 Maxima that has been treating me well!
Negative works equally well, the purpose is to open the circuit to the battery, the advantage of Negative is when you have a wrench on the battery terminal to loosen, or tighten the battery cable if your wrench slips and touches any piece of metal , you will not have the sparks fly like you would if your wrench was on the positive terminal and it touched something metal.... I hope this makes sense
+Ps3mn1 be much easier if you remove the intake.. I replace mine with new battery, starter and alternator still won't start... Any idea what could it be? I was told my IAC needs to be replace.
+Ps3mn1 be much easier if you remove the intake.. I replace mine with new battery, starter and alternator still won't start... Any idea what could it be? I was told my IAC needs to be replace.
It wasn't too bad without removing the intake, but thanks for the tip! And if your vehicle isn't starting it could be the Ignition Switch, the vehicle won't crank. Mine went bad on me 2 years ago, I believe it was $50 for the part.
how about showing what the fk you need to do to get at it!? Its BURIED under intake and other shit. No shit, put the part in and plug it in and fasten the bolts. Thats not what people are coming here for. This is a joke
cool, weather permitting I tackle this re & re tomorrow up here in Canada... cheers great down to earth video...
Thanks for the video, great tutorial straight to the point. Getting ready to change mine now.
I have a 01 maxima and the bolts are the same 14mm and 17mm I'm changing my starter today thanks! I didn't know where my starter was...now I know. I just bought my max a year ago and I'm putting all new parts on it today! new alternator new battery and starter!
Hey, glad to help! I still own my Maxima, and I just reached 280k miles and she's still on the road! You picked the right vehicle!
He should have took out the battery maybe he would have more space to work on it
Thanks for the video bud!
Thanks, video was helpful! Have a cold one on me!
Good video .thank. Puerto Rico's maxx. Tito. Caribbean's fever
Thank you.
Nice I can do my one when it starts to wear out shot g
Can’t find where a Connor goes
When you started your Maxima made that extended noise kind of a grinding sound after it started for a couple seconds. Mine is doing that same thing but maybe a little worse. I was thinking it might be my starter going out. My starter is still working fine but I don't want to replace it if that is not the cause of that sound. I'm also getting code p1320. Any suggestions?
Mine is the same. Figure it out?
How many teeth has the starter?
1996 european Maxima 2.0 V6 A32 m/t
can I change my starter on my 1995 nissan altima and base it off of this??
Oh lord.
On 8:35 u show the wire that gets attached to the top bolt but not in the bottom bolt. Does nothing get attached to the bottom bolt?
Correct, the bottom bolt just attaches to the motor.
Do you have any tutorials on how to put a cold air intake on?
The
@@tonyespinosa8125 I do not, but I could make a quick tutorial on my current Maxima! It's an 05. Same concept on most vehicles
question my lights on the dashboard where the radio and ac/heater is located there is no power ??
I would check your fuse block under your dashboard, on the drivers side.
I believe it's the very top right fuse, the 7.5A one.
Nice intake!! Where you got it from?
Jose Tapia I bought mine at O Riley's auto parts. Just the pod filter, the assembly was bought on Amazon. If you wanted links to purchase them let me know. Also, if you wanted to hear how she sounds please watch my 0-60 and reaches 285k mile video. It's my most recent video. Thank you.
Ps3mn1 Thanks!
Nice but it draws in hot air now. The factory was something of a cold rammed air intake already.
I have a no start issue with my 97 Maxima changed the start still nothing please help
The same thing happened to me, I changed the fuel pump and filter and it started, it could also be an ignition coil problem and spark plug
That's what I'm dealing with now on 2000 Sentra 1.8. The bindix goes forward but will not turn. After 3 days of working fine, then a couple days of starting with a little bit of grinding noise at first. Think I should shim it?
You never did show how to get the starter out.
How has this starter held up?
Yes
Hey, sorry for the late reply. Car was starting great since I've replaced it. Sadly she went to the scrap yard 3 years ago. I have a current 05 Maxima that has been treating me well!
Why negative disconnect ?
I've always done positive.
Tinman Bigfoot Tracker en español
Glass half full
It's always positive. It gets positive power almost directly so the negative does nothing for safety
Negative works equally well, the purpose is to open the circuit to the battery, the advantage of Negative is when you have a wrench on the battery terminal to loosen, or tighten the battery cable if your wrench slips and touches any piece of metal , you will not have the sparks fly like you would if your wrench was on the positive terminal and it touched something metal.... I hope this makes sense
is it easy
It wasn't too bad of a job, took 2 hours at most!
+Ps3mn1 be much easier if you remove the intake.. I replace mine with new battery, starter and alternator still won't start... Any idea what could it be? I was told my IAC needs to be replace.
+Ps3mn1 be much easier if you remove the intake.. I replace mine with new battery, starter and alternator still won't start... Any idea what could it be? I was told my IAC needs to be replace.
It wasn't too bad without removing the intake, but thanks for the tip! And if your vehicle isn't starting it could be the Ignition Switch, the vehicle won't crank. Mine went bad on me 2 years ago, I believe it was $50 for the part.
how about showing what the fk you need to do to get at it!? Its BURIED under intake and other shit. No shit, put the part in and plug it in and fasten the bolts. Thats not what people are coming here for. This is a joke