Matt...it's called 'spalting', it's the fungus beginning its initial work in the rotting process. Now that you'll be creating lots and lots of sawdust, and I'm fairly sure you've already thought of this, you can find unit to turn your sawdust into pellets for a pellet stove. If you haven't thought of it so far...invest in a metal detector before you ruin an expensive blade. You may want to consider some hearing muffs. Sorry for the thoughts from my cheap seat...another great video.
Not to forget a First Aid kit If it happens that he lobs off a finger or two or worse 🤕 and maybe a tourniquet with a course on how and what to do with it 😉
Good call regarding the sawdust John. I was also going to mention, in some videos of similar wood cutting, I noticed that some of them connected buckets, or even in one, a vacuum system to collect the dust from their saws.
Yea some youtuber made a whole automatic deal that took the sawdust from the mill, when it got to a certain fill point he had a conveyer take the stuff to a press that would press out pucks then dump them into the furnace based on what temp he had a thermostat set to..
Old Sawyer here. Gotta rag on you some but will make life easier.#1 attach your rails to the concrete ( it moved when you put the first log on it)#2 ease into the log real slow to start then speed up. Listen to the mill, it will tell you how fast to go. #3 be sure the log is on cross rails on both ends, this helps do away with warping. # 4 two back dogs and one on the front are plenty, saves time. #5 personally I would raise the rails up to about 30 inches, saves the back. #6 throw your scrap on the forklift, handle it once and be done. #7 do not put that spalted lumber on your dump truck, the local woodworkers will lynch you for sure. Keep up the good work and continue to learn and life will be great.
Mill tips , first buy extra dogs ! Have a set for tall wood and set the other low so you don’t have to constantly change ! #2 a squirt of dish soap in a tank of water will work as lubricant fluid in the summer otherwise windshield washer fluid (-20) for fluid in the winter ! #3 make a pre staging deck to set multiple logs on with machinery and then hand roll them onto the leveled deck ! The less bouncing big logs on your cutting deck the more consistent your cuts will be ! Good luck…
You could see the deck move when the log hit it @24:43 Plus it almost rolled off the skid steer just before that, and if that had rolled onto the deck, it would not have been good.
There are sooo many sawmill videos online. I wonder why this guy didn't feel that he could use some advices. For instance: Use a pressure washer to clean the logs while having them on the forks of the skid steer or loader. It will definitely help that the saw blades last longer 2) Use a metal detector! This will also help that the sawblades last longer. 3) Use ear protection! And sometimes even a dust mask! 4) Take care of the sawdust. Don't let it sit on the ground near the sawmill and pile up. There's a lot one can do with sawdust. 5) Don't put the boards/slabs in your way. 6) Don't burn the slabs/rind boards because those can definitely at least become fire wood. It's t's useful biomass and one can sell the slabs and even the sawdust (although I would press big pellets out of the sawdust).
From one Woodmizer owner to another, I can offer you a few suggestions. Firstly, try to have the ends of the logs on the bed rails (or a close as possible). Logs with more stress (i.e. poplar trees that may have grown on a slope) will bow downward when you take wood from the opposite side. This will cause for boards with unequal thickness throughout their length. Clamped properly and supported at the ends will prevent this unnecessary waste. Also, not taking a lot off of on side before turning to get an equal amount from the opposite side will also reduce bowing. This is mainly in softer woods, not so much in the oaks. Happy sawing!
Just to clarify, "try to have the ends of the logs on the bed rails" This means the bow should be an arch correct? (as opposed to being U shaped, with center of log touching rails, and ends of log in the air)
Actually, you try to avoid a bow by secure clamping. You can do this by cutting the logs to (or near) the length of the cross bed rails. Rails are spaced approximately 4' apart. If you have a 14' log, try to positon where there is a 1' overhang on BOTH ends and not a 2' overhang on a SINGLE end
They are more expensive, but Matt Cremona shifted to using carbide teeth blades...and they work well enough to cut through metal. he has this video and many others on that ruclips.net/video/euVanVFtsww/видео.html Here is another person who used carbide blades and what they thought after hitting nails and not even realizing it ruclips.net/video/f7ho_zBy8h4/видео.html
@@kevinandrew1361 I have two of them and did a video on their effectiveness, the larger wand one is definitely better and more sensitive ruclips.net/video/rEM6m1enNIM/видео.html
Honestly, the sawmill is great for time-lapse stuff. It's good filler videos to put out between projects. Whole channels are dedicated to milling so it's definitely got an audience!
Matt flip that machine 180°. Exhaust sawdust ejection toward the yard. Fuel and coolant toward the building, a little dawn helps, slippery when wet. Know bigger than 26"! And make some thin cribs for stacking. Please be on your best! This puppy is cool but can kill in the blink of an eye. And get more dogs and peaveies of all sizes. Get shims to place underneath the long cuts and save on blade burn and tension friction lot's of drag. Just a little love goes a long way. I can't what to see the look on your face when you brack a blade. Remember to do your duck impersonation. Low and live 50/50 ish chance. Bsafe or ill tell your wood dog's. 🥶🐲
Hi Matt, You struck gold with your first log, even if you don't know it yet. That's spalted wood, highly priced by furniture makers, and it makes for spectacular cabinet doors. If you slap it on this side of your dump truck, woodworkers from around the world will show up at your door with a hanging rope ready. Seriously, if you can't use it, sell it. It should bring top $.
How many of us are gonna buy it off of him and go there to pick it up? Same thing with Letsdig18, tears down a trillion trees, best believe a lot of that is spalted, and when he burns it everyone said it's a waste, so he asks people to pick it up = Nobody comes and gets it.
Spalted wood isn't that special, go chop an oak tree down and then let it sit a winter on the ground. It's not as structural and it sucks as firewood but some dumbass from LA will buy it.
@@hulkhogan2113 Precisely, have dealt with spalted wood more times than I'd care to remember, always bad news for firewood. But for dump truck duty it should be alright!
I milled on a dimensional mill for years. For every new job, I start with the worst logs that are easy to get at and cut some bolsters and stickers. 2nd make cribbing for the slash to easily trim it into firewood. When stickering place a sticker on each end to help prevent splitting from the end drying too fast. The width of your piles dictates the sticker length most mills have 4ft and my equipment 3ft wide piles worked best. Making these dimensions standard makes your piles neet and loading trucks and trailers easier. Placing your stickers on 2ft centers allows for stacks 8ft high because bolsters can be placed over stickers and make taller piles and straighter lumber when dry. I have seen so many get in a rush and not stack their lumber correctly and have a pile of kindling in 2 years when it has dried. Have fun!
As far as I'm concerned the videos you create transcend "working on heavy equipment for you guys". They've always been more of a "lifestyle that I wish I had" type of content, in which this falls right in line with, in my humble opinion. You don't just pick up equipment just to get it running. You put it to use and also tour with the equipment that you have resurrected, to the vintage equipment shows and are part of a thriving community. You also provide inspiration (hopefully) to a younger generation of aspiring mechanics and JOATs to get off the gaming consoles and out there doin stuff that's real!
In today’s world just because something says Made in the USA doesn’t always mean it was truly made in the USA. I used to work for a company that advertised and labeled their products as Made in the USA but 90% of the parts came from China, 5% from India, 4% from Mexico and 1% from the USA. The company got away with saying Made in the USA because they assembled the parts in the USA. Great video and thanks for sharing.
Once you have had a motor to open that door you will only use the manual mode when there is no power Matt. Congratulations on the saw. My best friend bought a wood miser. After he had it for a couple of years he suffered 2 severe strokes and decided to sell it. I know it broke his heart. He is in his late 70s and sits in a chair and looks at all the projects he collected for these days before. Take nothing for granted. Be safe with that saw. Cheers Terry
That strange wood grain pattern is I believe called spalting Matt! Well it is here in Europe. Operated a Wood Mizer 25 years ago in the woods in Shropshire. Awesome machines. 🤭🤔 It's definitely a long term investment that will repay you if you look after it!
Great to hear you've managed to make this your full-time occupation, Matt. It's incredibly rewarding to see you succeed at what you love doing, and I look forward to following your progress for years to come.
Also, power feed is nice, but every wood type has a different speed at which it cuts best. As a beginner you would benefit by using hand feed to get a feel for which wood wants what speed.
@@TheLoxxxton I thought that as well! Still, if it were Chineseium bolt would have been stripped clean, head would have been round and the blade would have snapped!😄
Good show and tell today! Unless your goal is to make lumbermill cuts, you can just make a primary cut and flip it 180 degrees and slab cut the log leaving the other edges rustic. A good table saw can finish the rest. Nice to see the Made In America label. Also good you brought up the boogered bolt threads publicly!
You might want to build a landing dock to set your logs on and then roll them from the landing dock on to your mill carriage. --- Easy to make one out of a slightly modified old trailer frame, this would be easy to move later also. --- Ron & Marilyn Hansen
Hey Matt, loved the video! Just a tip to help make sure your logs are nice and square, when you take your first slab off flip the log over so the flat side is sitting on the rails that way the top and bottom are square to each other, then when you go to cut the 3rd side of the log, take a framing square and set the long side down on the rail of the mill and slide the short side up to the already cut side,that way your log will be as close to square as you can get, it will save time trying to eyeball it and down the road when you go to make a finished product the board will already be square, hope this helps!
As others have said , its spalted. No reason to apologize for doing something that makes "You" feel good. Everybody needs something that makes you feel happy and good and to relax. Anytime you want to throw in a saw mill episode I think you will find More people who approve than those who say no. Keep up the fantastic work making content. I do not know how the U Tube system works but I am glad i found a few channels I like. Keep it up.
Congrats on finally getting your saw mill. One suggestion, I know you are enjoying the automatic feed, but in future you should keep your hands near the controls. You will invariably run into things like spikes and such that you will want to shut down immediately. Also, be mindful of the amount of sawdust you will be walking through. Looking forward to your adventures with this machine. I assume when you watched your video, you saw you knocked the base when loading the log, so may have loss your level.
@@ThompsonsWorkshop Yeah. It's too late now, but he should have mounted the system 180 degrees from where he did, so the saw dust would discharge AWAY form the building's windows and doors.🤣
@@v3124 I have no personal experience with them either. I was basing my comment on this: ruclips.net/video/rBK5781UrwA/видео.html, but now I see it is not even the same brand.
Milling lumber is one of my favorite RUclips genres. I definitely want to see more Diesel Creek milling vids. Like that big pine log, you teased us with at the end here. I want to see it opened up and milled. It will be quite interesting to see your trees felled and milled for use on your property. Don't be hesitant, people will watch.
I don't know about the rest of the industry but in wood turning we call those black or grey lines in the wood "spalting" which is a fancy way of saying mildew, which is cuased by wood sitting for a long time in a damp climate. . I know you will get plenty of safety and operational tips from us and here is mine, from an experienced woodturner (I make round things on my lathe) wear some kind of dust mask, even if it just to use up those old covid masks when cutting wood. Those fine wood dust particles will get in your lungs and can eventually cause bad breathing problems. You can still enjoy the fragrance of the fresh cut timber, and I agree, it is great. P.S. Be sure ti keep a bottle of eye wash handy for those times a breeze comes along and blows that sawdust right in your eyes. I take many precautions for breathing and googles, face shield etc., and still occasionally get sawdust in my eyes and the eye wash is essential. Two pretty essential things in life, your lungs and your eyes.
Hey Matt. Congrats on the new mill. I've had mine for a couple decades. Your log was spalted, which is early decay caused by fungus, makes for some really interesting grain. If you really want to show off the grain, wet the slab and scrape the excess water off with a 12" drywall knife. Wood is much easier to mill when it's wet, go slower when the logs are dry. Not sure if you got a sharpener with it, but you may want one. You really can't cut very much per blade otherwise. Have fun! -Jon
neat machine. We got bigger one at our sawmill. A lot more automated. Couple tips: The initial contact between blade and log needs to be as slow as possible. Once blade is in, you can go faster. It minimizes risk of snapping the blades and causing wavy cut. Run it with plenty of water/lubricant. Once you start noticing waves on cut logs then you gotta change the blade. We run ours about 90-120min each between switching.
To ensure things last, use the RTFM rule. (Read the f***ing manual). You could also save yourself money by collecting the sawdust in a bucket. Less sweeping up, so less accidents and dirt tramped into your buildIngs.
Milling lumber isn’t boring to watch at all. If you do more we will Watch! Keep up the good work, you inspired me to go out on my own and build my own auto repair shop! Thanks again for the awesome content
Matt when you see that log turn into something useful think you are the first person in the world to see the grain ! As a wood Turner seeing a bowl or candlestick emerge from the rough is immensely satisfying . My late father would have loved your videos . Once helped him to take an engine out of one car and fit it into a different make 😅
it might be worth it to bring us along while you learn how to use your sawmill. It gives those of us who haven't seen one in action an idea of how planks are made. It gives your viewers who own sawmills a chance to give you tips if you run into trouble. They'll probably give the same level of satisfaction that all the power washing videos provide. And, you might inspire someone who's in a similar situation, who's not sure if it's feasible, to say I can do that, and get one of their own. For me, it reminds me of watching This Old House with my dad when I was a kid.
It's going to be awesome to turn standing dead logs into dimensional lumber for the house you're going to build. There's something great about milling lumber from trees cut on your own land. Very cool, Matt. Looking forward to seeing this machine pay for itself!
As soon as I saw the blue Logrite log handler, I got a big smile. Logrite, which is located just a few towns over from me, is owned by some fantastic folks who are friends of mine. They also manufacture BlueCreeper which is probably the most miraculous penetrating lubricant I’ve ever used. I actually helped them develop a sewing machine oil that is by far THE BEST lubricant for sewing machines both domestic and industrial. Everything they make is done right here in the US and is always top quality materials and construction. Nice. 👍🏻😎👍🏻
Out of the woods RUclips channel is the channel you kneed to watch he has a wood mixer 70 and is very informative. Also has a saw blade that he recommends
Yes, I enjoyed that! There are many channels that mill for their homestead, but I think that they're a different genre than you, Matt. It's okay to film according to your projects, not every video is specific to the single piece of equipment , but instead to the individual project. Do as you see fit as you know we'll all watch you expand your shop and properties. Have fun and be careful! William
I don't know why, but I have always enjoyed watching these smaller sawmills at work. There is just something so satisfyingly about watching them cleanly slice the wood. Also, the constant flow of sawdust out the expel chute is very satisfyingly as well to me. Be sure to change the oil in that Kholer sooner rather than later. 100% guarantee you there will be a little glitter from break-in. Change it again after a few hours of service, then you can go to normal intervals. (I know you know this already, just arm-chair quarterbacking) :) Also, save the sawdust. It has so many great uses, and can even be sold.
You may enjoy watching the girls milling timber on Lumbar Capitol Log yard. They often show how to’s and techniques for the Woodmizers, both 15 and 40. The colour changes in the first cut showed the fungal splatting, which is nice.👍😁
Matt I started watching your channel for the cool old Iron you save/start/use. I stick around because I love to see what you are up to next. The shop build, although outside of your channels purpose, is one of my favorites. So please just keep making videos of your day to day stuff. I think most of us just love to see what you are up to. ✌
I love it! And I'd love to see you harvest all the wood you have been storing as logs on your property! It's not boring at all. Love to see the results. Keep it up!
I have watched quite a few YT videos of people using various Woodmizer mills, but this is the first time I have seen what a neat job they make of packing them up for transport, and someone assembling the mill. Thanks Matt for that. One thing that always strikes me as strange with Woodmizer mills is that they are designed so that the sawdust comes out the side that the operator stands. Some other mills on the market have the blade running the other way so that the sawdust is on the opposite side to the operator.😀🇬🇧
I really appreciate your time and effort in sharing these videos Matt, thank you. My only complaint is that this video could have been two hours long....I enjoyed the hell out of watching that! Please make more of those.
Hey Matt I'm pretty sure most of your subscribers would enjoy you doing just about anything always a thumbs-up from me thanks for such a great Channel looking forward to see what you do next congratulations on your new sawmill truly hope to see more videos on it
Matt doesn’t matter if you show the sawmill every time you use it or anything else you do it all entertaining. And I for one look forward to watching your post every week. It gives me a chance to see what a friend who always has a contagiously great attitude is up to. Keep up the great work and stay safe.
I do woodworking as a hobby, turning the most. For me, there is nothing more relaxing than making a big pile of wood shavings on the floor. One tip when you are cutting a log, put water on the slab you just cut, it will make the grain just pop right up. Enjoy y0our saw.
You might want to take some of that scrap wood and make a backboard for the sawdust to hit and to contain it until you can sweep or vacuum it up. Also, now that you have a source of sawdust, you may want to invest in some kind of pellet maker, to turn that sawdust into pellets for the floor heater shed. Looks like a great purchase, and a lot of fun. Enjoy many years of cutting.
It would be really cool to see you make something (even a workbench or storage shelves) going from log to finished product, I love your channel and always look forward to the next video!!
I know the feeling! i waited almost 16 months for my Wood-Mizer LT35HD. You look like you are figuring it out fairly well. One tip I'll give is to put your off cuts on the other side and straight on to the forks for easy removal. Happy Sawing.
You can always add a few of these vids in the mix, there is something very satisfying about watching wood being milled, your wife is going to see all the wonderful wood grains as you work the machine to the point of you having other projects or even better her. Always fun to watch Matt, it's been a blessing to watch you grow and to see things come to fruition, just wait until you get that wood boiler, nothing will ever go to waste. You'll be investing in a few good chainsaws but man they are worth it, go check out Joe on "Northern Seclusion" he's had his new wood burning boiler for a few months now in Minnisota running it 24/7 in 30 below weather, that'll give you a glimpse of how much energy they can produce.
Hey Matt, awesome machine! A couple of observations from an old man. You might consider hanging a bucket from the sawdust spout to cut down on the broom time. Also , Have you ever considered collecting water off of the roof of that awesome new shop? A storage tank set high in one inside corner could easily retain enough water to gravity feed and service a bathroom. Love your videos and your hard work ethic.
That's an interesting idea I have something that keeps the toilet from using so much water it's called a Mansfield flush valve which you can put on about any toilet if it's not a Mansfield toilet the deal is you can control the duration of the flush anytime you pull up on the handle it stops the water from going into the bowl so no more overflow and also makes for a short flush option.
Hey Matt, big fan of the lumber cutting. I would love to see at least one more video especially of you learning to use it. I'm hoping to get a mill in the next few years and I'd love to see the rest of your journey.
Good to see you Matt, Sawmill sounds like a good investment with the Price of a Filleted Tree these Days! You are living the good life Brother, God Bless You . I have been watching since the Early Days from the Garage and knew you had a good thing. I’ll catch you on the next one, Keep it Safe Out There Sir
That is EXACTLY the brand and model mill I’ve been drooling over for a while now. I REALLY hope that you do more videos of using it showing the learning process of using it!
I need to reconsider my decision to build a mill using a chain saw. This looks like a sweet setup. Now I need to go take a nap. Watching your endless supply of energy, while fun, is exhausting.
Nice Matt, my friend has the same one . He is always cutting for me in CT. Fyi : set up micro switches on either side of the track that will shut down the power feed.
Matt, I had a cousin that built a saw mill. The bearings for the blade guide came from scrap from a local hospital after they stripped it down. He used car tires for blade pulleys, and it didn't do bad, but he just wasn't completely happy with it, so he sold it. I was in a Home Depot when I met a guy that was looking for parts to finish it up. It turns out that this was the guy that bought my cousin's saw.
congrats man,a little trick I like to use when cutting logs is find the smaller end of the log and make a mind map of what you can get out of the log ,like a 4X4 in the middle and 2 - 2x4 on both sides then maybe 2- 1x6 on the other sides if that makes any sense
Nice , relax but let's get the terms right. Slabs are first cuts to square log. May be all that comes if making timbers. Planks is what you cut after squared off. May not be mobile as chainsaw mill, but should give you good service.
Heck yeah Matt. Can't go wrong with a Wood Mizzer. Went to the Indy plant and got one with a buddy years ago. They pay for themselves. You can also use your outside wood stove and create a kiln. That also works well.
Matt it’s your laid back presentation of your videos that shine through, i enjoyed the wood sawing as much as anything so keep keep on doing your thing and subscribe everyone a great channel to relax and unwind
Tip on work-tactics: Place the skidsteer so you can toss the waste products on the forks and the products against the workshop wall. This way, you'll facilitate work by making it easier to remove waste products, no need to place the actual products to a better drying place, and you also increase safety so you won't fall on the waste. I would also consider moving the engine control switch (ignition switch) to the operator's panel for safety and convenience. Nice mill, Matt.
Great video Matt. Love the variety in your videos. Would enjoy more shop build, wood cutting, equipment repairs, excavating, etc. Your videos are always a joy to watch. It won’t make me mad if you put out two videos a week.
I believe the discoloration you wondered about is called "spalting". You'll sometimes see references to "spalted wood" in fancy furniture descriptions. I loved this video. My Grandad always wanted one of these, and I've enjoyed watching different bandsaw mills at various machine shows over the years. Seeing it go together and run was a blast. H would have enjoyed watching this video.
Yes, Matt I love watching you saw that lumber up. It’s one of my favorite things to do is watch how the woodgrain reveals itself, which is very important especially if you’re making furniture or some kind of wooden project. Wood grain is very important. I love looking at it nice job, Philip.
Mat I watch your channel because you have a variety of things to watch, But no worries I like seeing the sawmill work also. Keep up the good work I love your channel.
Definately loved it Matt. I loved working with wood in my earlier years. Every piece has it's own character and when you can take it from the pile and display that character it's like breathing new life into it. All for it, and definitely not boring to watch (at least for me).
I have been watching now for over a year, i have a earthworks business in Australia and try and do all my own maintenance and make my own trailers etc. It can feel lonely travelling on your own path like this and your videos make me feel like im not the only guy living like this haha. Plus your videos have a chilled vibe to zone out and enjoy
Matt working on a new machine, not one older than him? What kind of heresy is this? But it's always great to see your joy at getting into something, you're like a kid at Christmas. Its great to see this lumber you cut so long finally becoming timber (I think that's right in American speak) it's been a long time coming. Appreciate your honesty and humility, few would admit to their mistakes the way you do. Also credit for putting that thing together without reading the instructions. Can the saw go on the other side so it ejects waste away from the shop rather than into it? Seems a shame to mess up your beatiful new shop is all.
Cant believe how quiet that was when it started. Quieter than the starter! That's amazing on a small engine and probably a lot of relief on the hearing when you are in between cuts.
Hey Matt, tie a small string to the feed leaver long enough to go the length you want, once it goes the length it'll pop the lever into neutral and you're good to go! (Assuming there's not too much momentum and it pops it into reverse, because that's not ideal!)
Thanks Matt that brings back a lot of memories for me as I started my working life in a timber mill back in 1972 in Australia. I went on to be a saw doctor ( which you call a saw filer) and sharpen big band saws but thanks again for the walk back in time ..Your very versatile in your videos' so keep it going MATE.
In addendum to my previous comment, that spalted maple is highly desirable in some circles! I've seen the wood turning (lathe) community go absolutely berserk for certain spalted pieces.
Matt , I have the notification bell done and I hit the thumbs up for every video , plus I'm checking all the time for new videos from you. The sawmill is a brilliant idea for you and hopefully it will save you a fortune in lumber , prices being what they are now. Of course when you build your forever house on your farm we all expect you to be producing every stick of lumber in that house build yourself. And you can chunk all of the log offcuts to burn in your log furnace to heat up the dream workshop , so nothing will go to waste , win /win as they say . Best regards to Eva and , woof woof Roscoe and Meatball . I'm already looking forward to the next video buddy
I love your enthusiasm, Matt, when you get to work with something new. Congratulations with the new saw, and I know it will be in good hands to produce the wood you are looking for, useful for you to reach goals! Thanks for the video!
Just can’t beat doing something the first time and seeing your process come alive. We have an Ireland circular mill with a 4-71 Detroit, sawed our home and shop all with it. Running a mill is always a pleasure with the pride and cost saving that goes on. Cheers and can’t wait to see the builds you do with the woodmizer!
Hi Matt - love the content, variety, challenges, creative solutions, camera work/perspectives...the whole package! Keep up the great work and 1000% agree (may need new calculator....) have to do, or at least incorporate, what you love in your life.
Looking for a LT40 used. Found one for $26k No sure if it's worth it. There is a de barker option that goes in front of band saw entry which cleans dirt sand away from blade entry into log. Doubles life of blade. Nice 👍
Do shorts of making the planks for.... The trailer decks, Etc. you are right, filming every single second would be wierd, but a little of it is Diesel Creek. 🎯 Now to find suitable hardwood for the deck planks, and then load up the Kobelco and take it out behind the tractot with the new engine and transmission. And fresh tires.
Matt...it's called 'spalting', it's the fungus beginning its initial work in the rotting process. Now that you'll be creating lots and lots of sawdust, and I'm fairly sure you've already thought of this, you can find unit to turn your sawdust into pellets for a pellet stove. If you haven't thought of it so far...invest in a metal detector before you ruin an expensive blade. You may want to consider some hearing muffs. Sorry for the thoughts from my cheap seat...another great video.
Not to forget a First Aid kit If it happens that he lobs off a finger or two or worse 🤕 and maybe a tourniquet with a course on how and what to do with it 😉
Good call regarding the sawdust John. I was also going to mention, in some videos of similar wood cutting, I noticed that some of them connected buckets, or even in one, a vacuum system to collect the dust from their saws.
Yea some youtuber made a whole automatic deal that took the sawdust from the mill, when it got to a certain fill point he had a conveyer take the stuff to a press that would press out pucks then dump them into the furnace based on what temp he had a thermostat set to..
Soak sawdust in used oil to make bricks burn hotter
Muffs are a priority for everyone. Unfortunately I wasn't smart enough oh so many years ago.
Old Sawyer here. Gotta rag on you some but will make life easier.#1 attach your rails to the concrete ( it moved when you put the first log on it)#2 ease into the log real slow to start then speed up. Listen to the mill, it will tell you how fast to go. #3 be sure the log is on cross rails on both ends, this helps do away with warping. # 4 two back dogs and one on the front are plenty, saves time. #5 personally I would raise the rails up to about 30 inches, saves the back. #6 throw your scrap on the forklift, handle it once and be done. #7 do not put that spalted lumber on your dump truck, the local woodworkers will lynch you for sure. Keep up the good work and continue to learn and life will be great.
Mill tips , first buy extra dogs ! Have a set for tall wood and set the other low so you don’t have to constantly change ! #2 a squirt of dish soap in a tank of water will work as lubricant fluid in the summer otherwise windshield washer fluid (-20) for fluid in the winter ! #3 make a pre staging deck to set multiple logs on with machinery and then hand roll them onto the leveled deck ! The less bouncing big logs on your cutting deck the more consistent your cuts will be ! Good luck…
I don’t know much about this kind of machine but I instantly thought man I’d build a deck to drop logs on so I’m not dropping them on the machine.
You could see the deck move when the log hit it @24:43 Plus it almost rolled off the skid steer just before that, and if that had rolled onto the deck, it would not have been good.
Wayne, should the boards be stacked with air gaps between them?
@@TrevorDennis100 When you move the lumber to a drying area, it needs to be 'stickered'. It isn't normally done as you cut it.
came here to say that about the dish soap. also, a sharp blade is your friend. if your blade starts wandering up and down, dull blade and replace.
There are sooo many sawmill videos online. I wonder why this guy didn't feel that he could use some advices. For instance: Use a pressure washer to clean the logs while having them on the forks of the skid steer or loader. It will definitely help that the saw blades last longer 2) Use a metal detector! This will also help that the sawblades last longer. 3) Use ear protection! And sometimes even a dust mask! 4) Take care of the sawdust. Don't let it sit on the ground near the sawmill and pile up. There's a lot one can do with sawdust. 5) Don't put the boards/slabs in your way. 6) Don't burn the slabs/rind boards because those can definitely at least become fire wood. It's t's useful biomass and one can sell the slabs and even the sawdust (although I would press big pellets out of the sawdust).
From one Woodmizer owner to another, I can offer you a few suggestions.
Firstly, try to have the ends of the logs on the bed rails (or a close as possible). Logs with more stress (i.e. poplar trees that may have grown on a slope) will bow downward when you take wood from the opposite side. This will cause for boards with unequal thickness throughout their length.
Clamped properly and supported at the ends will prevent this unnecessary waste. Also, not taking a lot off of on side before turning to get an equal amount from the opposite side will also reduce bowing.
This is mainly in softer woods, not so much in the oaks.
Happy sawing!
Just to clarify, "try to have the ends of the logs on the bed rails" This means the bow should be an arch correct? (as opposed to being U shaped, with center of log touching rails, and ends of log in the air)
What's the tank on top of the machine for? Matt didn't seem to be using it
@@InsanePacoTaco Water tank for lubrication sawblade and coolant
That is the holding tank for dead tree farts. If you dont capture them you wind up with a shitty situation…
Actually, you try to avoid a bow by secure clamping. You can do this by cutting the logs to (or near) the length of the cross bed rails. Rails are spaced approximately 4' apart. If you have a 14' log, try to positon where there is a 1' overhang on BOTH ends and not a 2' overhang on a SINGLE end
Matt you may need to get a moisture meter to how green the logs are and a metal detector to find nails in the logs so you don't dull blades.
Not just nails, but buckshot too.
Barb wire, chains
They are more expensive, but Matt Cremona shifted to using carbide teeth blades...and they work well enough to cut through metal. he has this video and many others on that ruclips.net/video/euVanVFtsww/видео.html
Here is another person who used carbide blades and what they thought after hitting nails and not even realizing it ruclips.net/video/f7ho_zBy8h4/видео.html
They have some good inexpensive hand helds like security .
@@kevinandrew1361 I have two of them and did a video on their effectiveness, the larger wand one is definitely better and more sensitive ruclips.net/video/rEM6m1enNIM/видео.html
Honestly, the sawmill is great for time-lapse stuff. It's good filler videos to put out between projects. Whole channels are dedicated to milling so it's definitely got an audience!
Matthew Cremona comes to mind for me. Do I watch him cut up big logs, oh yes I do.
Plus eventually we will see Matt put the wood to use on his house.
Matt flip that machine 180°. Exhaust sawdust ejection toward the yard. Fuel and coolant toward the building, a little dawn helps, slippery when wet. Know bigger than 26"! And make some thin cribs for stacking. Please be on your best! This puppy is cool but can kill in the blink of an eye. And get more dogs and peaveies of all sizes. Get shims to place underneath the long cuts and save on blade burn and tension friction lot's of drag. Just a little love goes a long way. I can't what to see the look on your face when you brack a blade. Remember to do your duck impersonation. Low and live 50/50 ish chance. Bsafe or ill tell your wood dog's. 🥶🐲
Hi Matt,
You struck gold with your first log, even if you don't know it yet. That's spalted wood, highly priced by furniture makers, and it makes for spectacular cabinet doors. If you slap it on this side of your dump truck, woodworkers from around the world will show up at your door with a hanging rope ready. Seriously, if you can't use it, sell it. It should bring top $.
How many of us are gonna buy it off of him and go there to pick it up?
Same thing with Letsdig18, tears down a trillion trees, best believe a lot of that is spalted, and when he burns it everyone said it's a waste, so he asks people to pick it up = Nobody comes and gets it.
@@ToreDL87 So basically: Money Talks, Bullshit Walks. 😁
Spalted wood isn't that special, go chop an oak tree down and then let it sit a winter on the ground. It's not as structural and it sucks as firewood but some dumbass from LA will buy it.
@@danielseelye6005 It would appear that way!
@@hulkhogan2113 Precisely, have dealt with spalted wood more times than I'd care to remember, always bad news for firewood.
But for dump truck duty it should be alright!
I milled on a dimensional mill for years. For every new job, I start with the worst logs that are easy to get at and cut some bolsters and stickers. 2nd make cribbing for the slash to easily trim it into firewood. When stickering place a sticker on each end to help prevent splitting from the end drying too fast. The width of your piles dictates the sticker length most mills have 4ft and my equipment 3ft wide piles worked best. Making these dimensions standard makes your piles neet and loading trucks and trailers easier. Placing your stickers on 2ft centers allows for stacks 8ft high because bolsters can be placed over stickers and make taller piles and straighter lumber when dry. I have seen so many get in a rush and not stack their lumber correctly and have a pile of kindling in 2 years when it has dried. Have fun!
As far as I'm concerned the videos you create transcend "working on heavy equipment for you guys". They've always been more of a "lifestyle that I wish I had" type of content, in which this falls right in line with, in my humble opinion.
You don't just pick up equipment just to get it running. You put it to use and also tour with the equipment that you have resurrected, to the vintage equipment shows and are part of a thriving community. You also provide inspiration (hopefully) to a younger generation of aspiring mechanics and JOATs to get off the gaming consoles and out there doin stuff that's real!
In today’s world just because something says Made in the USA doesn’t always mean it was truly made in the USA. I used to work for a company that advertised and labeled their products as Made in the USA but 90% of the parts came from China, 5% from India, 4% from Mexico and 1% from the USA. The company got away with saying Made in the USA because they assembled the parts in the USA. Great video and thanks for sharing.
I have a feeling one day we will see a video of fitting an electric motor on that enormous door!
He'll use that big Detroit engine lol.....fastest garage door opening ever
first thing that came to mind. that door needs a motor ASAP
Once you have had a motor to open that door you will only use the manual mode when there is no power Matt.
Congratulations on the saw. My best friend bought a wood miser. After he had it for a couple of years he suffered 2 severe strokes and decided to sell it. I know it broke his heart.
He is in his late 70s and sits in a chair and looks at all the projects he collected for these days before.
Take nothing for granted.
Be safe with that saw.
Cheers
Terry
Another great video Matt! Thank you for how diligent you are with cranking out new and interesting content!
That strange wood grain pattern is I believe called spalting Matt! Well it is here in Europe. Operated a Wood Mizer 25 years ago in the woods in Shropshire. Awesome machines. 🤭🤔 It's definitely a long term investment that will repay you if you look after it!
The spalting is highly prized by woodworkers. He should find a buyer and not using them as to to throw away boards.
Great to hear you've managed to make this your full-time occupation, Matt. It's incredibly rewarding to see you succeed at what you love doing, and I look forward to following your progress for years to come.
I appreciate that!
@@DieselCreek Happy St Patrick's day matt if you celebrate it & a big Slainte ( irish for cheers ) from donegal ireland 🇮🇪🇺🇲🍺☘️
You should take on a summer apprentice
To help gather downed firewood for mill and wood boiler for new shop
There’s a saw mill guy that cuts up unique wood. He always pours a cup of water on the slab to show the beauty of the grain.
Also, power feed is nice, but every wood type has a different speed at which it cuts best. As a beginner you would benefit by using hand feed to get a feel for which wood wants what speed.
15 months for equipment is insane. Great video Matt. We all need hobbies to escape reality.
Ah yes! 2nd bolt removed from a shipping bracket is cross threaded. Made in the good old US of A
lol after all said and done, that " hobby " is closer to 10G lol it's more of an investment than a hobby.
@@TheLoxxxton I thought that as well! Still, if it were Chineseium bolt would have been stripped clean, head would have been round and the blade would have snapped!😄
@@TheLoxxxton Probably 100% was made in the good old US of A but put together with Chinesium hardware
@@fomora12 Well... Buy Swedish. Always, buy Swedish I say! (No biased there at all!) 😄😜
Good show and tell today! Unless your goal is to make lumbermill cuts, you can just make a primary cut and flip it 180 degrees and slab cut the log leaving the other edges rustic. A good table saw can finish the rest. Nice to see the Made In America label. Also good you brought up the boogered bolt threads publicly!
Clean your wood, use a pressure washer if needed. The less sand and dirt the better for your mill. Saves a lot of work changing and sharpening blades.
You might want to build a landing dock to set your logs on and then roll them from the landing dock on to your mill carriage. --- Easy to make one out of a slightly modified old trailer frame, this would be easy to move later also. --- Ron & Marilyn Hansen
Hey Matt, loved the video! Just a tip to help make sure your logs are nice and square, when you take your first slab off flip the log over so the flat side is sitting on the rails that way the top and bottom are square to each other, then when you go to cut the 3rd side of the log, take a framing square and set the long side down on the rail of the mill and slide the short side up to the already cut side,that way your log will be as close to square as you can get, it will save time trying to eyeball it and down the road when you go to make a finished product the board will already be square, hope this helps!
Good reply cousin! 😊
I started with the quarter turn method, originally. I'm doing the way you suggested now. Works very well and makes sawing smaller logs easier.
As others have said , its spalted. No reason to apologize for doing something that makes "You" feel good. Everybody needs something that makes you feel happy and good and to relax. Anytime you want to throw in a saw mill episode I think you will find More people who approve than those who say no. Keep up the fantastic work making content. I do not know how the U Tube system works but I am glad i found a few channels I like. Keep it up.
Well said James,well said.
In 3000+ comments someone had to have said it, spalting is what gives the random patters you were admiring in the wood.
Congrats on finally getting your saw mill. One suggestion, I know you are enjoying the automatic feed, but in future you should keep your hands near the controls. You will invariably run into things like spikes and such that you will want to shut down immediately. Also, be mindful of the amount of sawdust you will be walking through. Looking forward to your adventures with this machine. I assume when you watched your video, you saw you knocked the base when loading the log, so may have loss your level.
I was thinking about a bracket to hold a bucket to catch the 'man glitter/organic floor dry'.
Also, won't be long before he decides sawdust in the shop is bad. The chute is blowing toward the shop wall and man door.
@@ThompsonsWorkshop Yeah. It's too late now, but he should have mounted the system 180 degrees from where he did, so the saw dust would discharge AWAY form the building's windows and doors.🤣
@@johnsykesiii1629 I've never used one of these machines, but I've only ever seen them loaded from the side he was using.
@@v3124 I have no personal experience with them either. I was basing my comment on this: ruclips.net/video/rBK5781UrwA/видео.html,
but now I see it is not even the same brand.
"I watched half of the online tutorial, so I'm basically an expert" had me laughing! Beautiful mill you will make it work
Milling lumber is one of my favorite RUclips genres. I definitely want to see more Diesel Creek milling vids. Like that big pine log, you teased us with at the end here. I want to see it opened up and milled. It will be quite interesting to see your trees felled and milled for use on your property. Don't be hesitant, people will watch.
I don't know about the rest of the industry but in wood turning we call those black or grey lines in the wood "spalting" which is a fancy way of saying mildew, which is cuased by wood sitting for a long time in a damp climate. . I know you will get plenty of safety and operational tips from us and here is mine, from an experienced woodturner (I make round things on my lathe) wear some kind of dust mask, even if it just to use up those old covid masks when cutting wood. Those fine wood dust particles will get in your lungs and can eventually cause bad breathing problems. You can still enjoy the fragrance of the fresh cut timber, and I agree, it is great.
P.S. Be sure ti keep a bottle of eye wash handy for those times a breeze comes along and blows that sawdust right in your eyes. I take many precautions for breathing and googles, face shield etc., and still occasionally get sawdust in my eyes and the eye wash is essential. Two pretty essential things in life, your lungs and your eyes.
Hey Matt. Congrats on the new mill. I've had mine for a couple decades. Your log was spalted, which is early decay caused by fungus, makes for some really interesting grain. If you really want to show off the grain, wet the slab and scrape the excess water off with a 12" drywall knife. Wood is much easier to mill when it's wet, go slower when the logs are dry. Not sure if you got a sharpener with it, but you may want one. You really can't cut very much per blade otherwise. Have fun! -Jon
Fancy seeing you here! Fun fact: Your channel was my first exposure to such consumer available mills and I've liked them ever since!
Answers that question. John or Jon?
High Jon!
steve
neat machine. We got bigger one at our sawmill. A lot more automated. Couple tips:
The initial contact between blade and log needs to be as slow as possible. Once blade is in, you can go faster. It minimizes risk of snapping the blades and causing wavy cut.
Run it with plenty of water/lubricant. Once you start noticing waves on cut logs then you gotta change the blade. We run ours about 90-120min each between switching.
Keep the woodworking video's coming. Very relaxing to watch, show some of your wood projects.
To ensure things last, use the RTFM rule. (Read the f***ing manual). You could also save yourself money by collecting the sawdust in a bucket. Less sweeping up, so less accidents and dirt tramped into your buildIngs.
Milling lumber isn’t boring to watch at all. If you do more we will
Watch! Keep up the good work, you inspired me to go out on my own and build my own auto repair shop! Thanks again for the awesome content
No really, run some asmr vids on it. I never regret any time on the mill
If it were boring there are a bunch of channels who would soon be gone!
Matt when you see that log turn into something useful think you are the first person in the world to see the grain ! As a wood Turner seeing a bowl or candlestick emerge from the rough is immensely satisfying . My late father would have loved your videos . Once helped him to take an engine out of one car and fit it into a different make 😅
it might be worth it to bring us along while you learn how to use your sawmill. It gives those of us who haven't seen one in action an idea of how planks are made. It gives your viewers who own sawmills a chance to give you tips if you run into trouble. They'll probably give the same level of satisfaction that all the power washing videos provide. And, you might inspire someone who's in a similar situation, who's not sure if it's feasible, to say I can do that, and get one of their own. For me, it reminds me of watching This Old House with my dad when I was a kid.
It's going to be awesome to turn standing dead logs into dimensional lumber for the house you're going to build. There's something great about milling lumber from trees cut on your own land. Very cool, Matt. Looking forward to seeing this machine pay for itself!
Yeah... until the building inspector tells you that your house doesn't pass code because it was built with uninspected lumber.
As soon as I saw the blue Logrite log handler, I got a big smile. Logrite, which is located just a few towns over from me, is owned by some fantastic folks who are friends of mine. They also manufacture BlueCreeper which is probably the most miraculous penetrating lubricant I’ve ever used. I actually helped them develop a sewing machine oil that is by far THE BEST lubricant for sewing machines both domestic and industrial. Everything they make is done right here in the US and is always top quality materials and construction. Nice. 👍🏻😎👍🏻
Out of the woods RUclips channel is the channel you kneed to watch he has a wood mixer 70 and is very informative. Also has a saw blade that he recommends
I second that! OOTW is a laid back saw miller.
I third that motion, OOTW, knows his stuff.
Yes, I enjoyed that! There are many channels that mill for their homestead, but I think that they're a different genre than you, Matt. It's okay to film according to your projects, not every video is specific to the single piece of equipment , but instead to the individual project. Do as you see fit as you know we'll all watch you expand your shop and properties. Have fun and be careful! William
Lumber capital log yard on RUclips has the Lt15 saw mill they would be happy to talk you through it.
Great episode Matt.
I don't know why, but I have always enjoyed watching these smaller sawmills at work. There is just something so satisfyingly about watching them cleanly slice the wood. Also, the constant flow of sawdust out the expel chute is very satisfyingly as well to me. Be sure to change the oil in that Kholer sooner rather than later. 100% guarantee you there will be a little glitter from break-in. Change it again after a few hours of service, then you can go to normal intervals. (I know you know this already, just arm-chair quarterbacking) :)
Also, save the sawdust. It has so many great uses, and can even be sold.
Matt has the biggest toy box in the world 😂. I'm here for it!
Do not forget Andrew Camarata.
Now you need a solar kiln
@@priestley749 youre right! Can't forget about Andrew
And Andrew camarata
But who got the most toys Andrew or Matt ????
You may enjoy watching the girls milling timber on Lumbar Capitol Log yard. They often show how to’s and techniques for the Woodmizers, both 15 and 40. The colour changes in the first cut showed the fungal splatting, which is nice.👍😁
Matt I started watching your channel for the cool old Iron you save/start/use. I stick around because I love to see what you are up to next. The shop build, although outside of your channels purpose, is one of my favorites. So please just keep making videos of your day to day stuff. I think most of us just love to see what you are up to. ✌
Rig a 5 gallon bucket on the saw dust output and you can eliminate a lot of the walking area mess while creating filler for a compost pile TN 🤠🤠🤠
I love it! And I'd love to see you harvest all the wood you have been storing as logs on your property! It's not boring at all. Love to see the results. Keep it up!
With you Joseph on that request, thanks much Matt for sharing your journey with us.
I have watched quite a few YT videos of people using various Woodmizer mills, but this is the first time I have seen what a neat job they make of packing them up for transport, and someone assembling the mill. Thanks Matt for that. One thing that always strikes me as strange with Woodmizer mills is that they are designed so that the sawdust comes out the side that the operator stands. Some other mills on the market have the blade running the other way so that the sawdust is on the opposite side to the operator.😀🇬🇧
I really appreciate your time and effort in sharing these videos Matt, thank you. My only complaint is that this video could have been two hours long....I enjoyed the hell out of watching that! Please make more of those.
Noted!
😊😊😊😊
I agree. Love watching milling. It's very Satisfying as my kids would say lol
Nice to see and hear the excitement of a boy with a new toy!!!
His wife has to hide his Christmas gift wrap in another state !!! 😊
That was a beautifully spalted log to do your first cut on Matt. Folks pay top dollar for planks off logs like that 🙂
Hey Matt I'm pretty sure most of your subscribers would enjoy you doing just about anything always a thumbs-up from me thanks for such a great Channel looking forward to see what you do next congratulations on your new sawmill truly hope to see more videos on it
Hey Matt you might want to attach some kind of box to catch the sawdust so you dont have as much to clean up and free oil dry for the shop
word
Matt doesn’t matter if you show the sawmill every time you use it or anything else you do it all entertaining. And I for one look forward to watching your post every week. It gives me a chance to see what a friend who always has a contagiously great attitude is up to. Keep up the great work and stay safe.
C.DODSON, WHAT A PERFECT DISCRIPTION OF MATT; A CONTAGIOUSLY GREAT ATTITUDE!
I do woodworking as a hobby, turning the most. For me, there is nothing more relaxing than making a big pile of wood shavings on the floor. One tip when you are cutting a log, put water on the slab you just cut, it will make the grain just pop right up. Enjoy y0our saw.
You might want to take some of that scrap wood and make a backboard for the sawdust to hit and to contain it until you can sweep or vacuum it up. Also, now that you have a source of sawdust, you may want to invest in some kind of pellet maker, to turn that sawdust into pellets for the floor heater shed. Looks like a great purchase, and a lot of fun. Enjoy many years of cutting.
It would be really cool to see you make something (even a workbench or storage shelves) going from log to finished product, I love your channel and always look forward to the next video!!
I know the feeling! i waited almost 16 months for my Wood-Mizer LT35HD. You look like you are figuring it out fairly well. One tip I'll give is to put your off cuts on the other side and straight on to the forks for easy removal. Happy Sawing.
Keep the wood dust in a bag to dry the oil that falls on the workshop floor, it's much better than a rag. 😁
You can always add a few of these vids in the mix, there is something very satisfying about watching wood being milled, your wife is going to see all the wonderful wood grains as you work the machine to the point of you having other projects or even better her. Always fun to watch Matt, it's been a blessing to watch you grow and to see things come to fruition, just wait until you get that wood boiler, nothing will ever go to waste. You'll be investing in a few good chainsaws but man they are worth it, go check out Joe on "Northern Seclusion" he's had his new wood burning boiler for a few months now in Minnisota running it 24/7 in 30 below weather, that'll give you a glimpse of how much energy they can produce.
Hey Matt, awesome machine! A couple of observations from an old man. You might consider hanging a bucket from the sawdust spout to cut down on the broom time. Also , Have you ever considered collecting water off of the roof of that awesome new shop? A storage tank set high in one inside corner could easily retain enough water to gravity feed and service a bathroom. Love your videos and your hard work ethic.
That's an interesting idea I have something that keeps the toilet from using so much water it's called a Mansfield flush valve which you can put on about any toilet if it's not a Mansfield toilet the deal is you can control the duration of the flush anytime you pull up on the handle it stops the water from going into the bowl so no more overflow and also makes for a short flush option.
No better way to start a weekend off. Matt I love what you do keep up the excellent work.
You are now going to need to build a shed to house the mill and the drying timber, but you have a great start.
Hey Matt, big fan of the lumber cutting. I would love to see at least one more video especially of you learning to use it. I'm hoping to get a mill in the next few years and I'd love to see the rest of your journey.
Good to see you Matt, Sawmill sounds like a good investment with the Price of a Filleted Tree these Days!
You are living the good life Brother, God Bless You . I have been watching since the Early Days from the Garage and knew you had a good thing. I’ll catch you on the next one, Keep it Safe Out There Sir
That is EXACTLY the brand and model mill I’ve been drooling over for a while now. I REALLY hope that you do more videos of using it showing the learning process of using it!
Based on what you've seen, still interested or thinking on another make & model?
I've got the lt40 super, I can't imagine running the mill without the accuset 2 computer and hydraulics to move the log around.
@@hulkhogan2113 yeah, I’ve seen guys using a mill and it had hydraulics to move the log, so much faster but I’m sure they’re crazy more expensive.
I need to reconsider my decision to build a mill using a chain saw. This looks like a sweet setup. Now I need to go take a nap. Watching your endless supply of energy, while fun, is exhausting.
Nice Matt, my friend has the same one . He is always cutting for me in CT. Fyi : set up micro switches on either side of the track that will shut down the power feed.
Matt, I had a cousin that built a saw mill. The bearings for the blade guide came from scrap from a local hospital after they stripped it down. He used car tires for blade pulleys, and it didn't do bad, but he just wasn't completely happy with it, so he sold it. I was in a Home Depot when I met a guy that was looking for parts to finish it up. It turns out that this was the guy that bought my cousin's saw.
🤣🤣😂😂👍👍🇿🇦🇿🇦...great story
congrats man,a little trick I like to use when cutting logs is find the smaller end of the log and make a mind map of what you can get out of the log ,like a 4X4 in the middle and 2 - 2x4 on both sides then maybe 2- 1x6 on the other sides if that makes any sense
Nice , relax but let's get the terms right.
Slabs are first cuts to square log. May be all that comes if making timbers.
Planks is what you cut after squared off.
May not be mobile as chainsaw mill, but should give you good service.
Heck yeah Matt. Can't go wrong with a Wood Mizzer. Went to the Indy plant and got one with a buddy years ago. They pay for themselves. You can also use your outside wood stove and create a kiln. That also works well.
Matt it’s your laid back presentation of your videos that shine through, i enjoyed the wood sawing as much as anything so keep keep on doing your thing and subscribe everyone a great channel to relax and unwind
Tip on work-tactics: Place the skidsteer so you can toss the waste products on the forks and the products against the workshop wall. This way, you'll facilitate work by making it easier to remove waste products, no need to place the actual products to a better drying place, and you also increase safety so you won't fall on the waste.
I would also consider moving the engine control switch (ignition switch) to the operator's panel for safety and convenience.
Nice mill, Matt.
I've heard it is a good idea to get a metal detector to run over your logs to findAny nails, fence wire, staples, etc. Blades are not cheap.
That's what I was thinking, turn the whole thing around so it throws the sawdust, slabs, and cut lumber out to the loader.
29:50 That discoloring in the wood from fungus is called spalting.
Great video Matt. Love the variety in your videos. Would enjoy more shop build, wood cutting, equipment repairs, excavating, etc. Your videos are always a joy to watch. It won’t make me mad if you put out two videos a week.
I believe the discoloration you wondered about is called "spalting". You'll sometimes see references to "spalted wood" in fancy furniture descriptions. I loved this video. My Grandad always wanted one of these, and I've enjoyed watching different bandsaw mills at various machine shows over the years. Seeing it go together and run was a blast. H would have enjoyed watching this video.
There's a lot to learn about milling lumber, I'm sure you can make a good series of this and take us along as you learn.
Yes, Matt I love watching you saw that lumber up. It’s one of my favorite things to do is watch how the woodgrain reveals itself, which is very important especially if you’re making furniture or some kind of wooden project. Wood grain is very important. I love looking at it nice job, Philip.
Mat I watch your channel because you have a variety of things to watch, But no worries I like seeing the sawmill work also. Keep up the good work I love your channel.
Definately loved it Matt. I loved working with wood in my earlier years. Every piece has it's own character and when you can take it from the pile and display that character it's like breathing new life into it. All for it, and definitely not boring to watch (at least for me).
I have been watching now for over a year, i have a earthworks business in Australia and try and do all my own maintenance and make my own trailers etc. It can feel lonely travelling on your own path like this and your videos make me feel like im not the only guy living like this haha. Plus your videos have a chilled vibe to zone out and enjoy
Big ups to all the Aussie Diesel Creek fans
Matt working on a new machine, not one older than him? What kind of heresy is this?
But it's always great to see your joy at getting into something, you're like a kid at Christmas. Its great to see this lumber you cut so long finally becoming timber (I think that's right in American speak) it's been a long time coming.
Appreciate your honesty and humility, few would admit to their mistakes the way you do. Also credit for putting that thing together without reading the instructions.
Can the saw go on the other side so it ejects waste away from the shop rather than into it? Seems a shame to mess up your beatiful new shop is all.
Cant believe how quiet that was when it started. Quieter than the starter! That's amazing on a small engine and probably a lot of relief on the hearing when you are in between cuts.
The only channel you actually look forward to the new video release 👍. Keep it up i`m already looking forward to the next video
Love seeing new wood cut, exposing the internal beauty of the woods natural grain. TOTALLY AWESOME
You can use that Saw dust for tons of things also Matt 32:23 @Diesel Creek
Congrats! I have always wanted one of these. You have the woodlot to make good use of it.
Hey Matt, tie a small string to the feed leaver long enough to go the length you want, once it goes the length it'll pop the lever into neutral and you're good to go! (Assuming there's not too much momentum and it pops it into reverse, because that's not ideal!)
Or mount a micro switch or push button to the trolley to stop the motor travel
Just remember, you have to show sawyer work quite often. We have to have our fiber.
Thanks Matt that brings back a lot of memories for me as I started my working life in a timber mill back in 1972 in Australia. I went on to be a saw doctor ( which you call a saw filer) and sharpen big band saws but thanks again for the walk back in time ..Your very versatile in your videos' so keep it going MATE.
Saw doctor?!
@@MrChrisfernand for a large saw mill - a very important person, a troublesome saw is basically something which can take down a whole plant.
@@MrChrisfernand YES that what we are called here in Australia you call them saw filers
I have worked on 3 inch to 12 inch saws ,levelling and tensioning the blades then sharpening them.
In addendum to my previous comment, that spalted maple is highly desirable in some circles! I've seen the wood turning (lathe) community go absolutely berserk for certain spalted pieces.
Matt , I have the notification bell done and I hit the thumbs up for every video , plus I'm checking all the time for new videos from you. The sawmill is a brilliant idea for you and hopefully it will save you a fortune in lumber , prices being what they are now. Of course when you build your forever house on your farm we all expect you to be producing every stick of lumber in that house build yourself. And you can chunk all of the log offcuts to burn in your log furnace to heat up the dream workshop , so nothing will go to waste , win /win as they say . Best regards to Eva and , woof woof Roscoe and Meatball . I'm already looking forward to the next video buddy
I love your enthusiasm, Matt, when you get to work with something new. Congratulations with the new saw, and I know it will be in good hands to produce the wood you are looking for, useful for you to reach goals! Thanks for the video!
Just can’t beat doing something the first time and seeing your process come alive. We have an Ireland circular mill with a 4-71 Detroit, sawed our home and shop all with it. Running a mill is always a pleasure with the pride and cost saving that goes on. Cheers and can’t wait to see the builds you do with the woodmizer!
I would love to hear that 471 sing while cutting wood do you have a u tube channel ?
The neighbors know when you run your mill🤣
man that mill will last forever with that old detroit powering it
Nice looking pattern in that wood 30:16 @Diesel Creek
Love seeing all the equipment helping the homestead come together. And Matt Cremora makes the wood reveal entertaining so…
Matt Cremona :)
Hey I’m proud of you getting something for yourself that you will totally enjoy, and thanks again for filming it.
Hi Matt - love the content, variety, challenges, creative solutions, camera work/perspectives...the whole package! Keep up the great work and 1000% agree (may need new calculator....) have to do, or at least incorporate, what you love in your life.
You will need to get a good metal detector scanner for nails and bolts in the logs.
Looking for a LT40 used.
Found one for $26k
No sure if it's worth it.
There is a de barker option that goes in front of band saw entry which cleans dirt sand away from blade entry into log.
Doubles life of blade.
Nice 👍
Congrats on that sawmill Matt! Can't wait to see the first project with "Diesel Creek" lumber!
Thanks for doing what you do and taking the time to film, edit and share with us!
Exactly.
Do shorts of making the planks for.... The trailer decks, Etc. you are right, filming every single second would be wierd, but a little of it is Diesel Creek. 🎯 Now to find suitable hardwood for the deck planks, and then load up the Kobelco and take it out behind the tractot with the new engine and transmission. And fresh tires.