This is true, I bought a set of 062 vortec heads, and after doing all the work my self and buying all the tools I bought to work the heads I ended up spending more than buying some nice brodix heads ( not to mention the headaches). The best part of doing the work myself was learning how to do it.
Ehh I'm currently doing a set of 906's myself. I surface them on my mill myself, back cut the valves, pocket ported, gasket matched, lapped the valves, new seals, stud kit, offset retainers, beehive springs, goodson alumi check all for just under $350. Now a hundred of that was the purchase of the heads themselves everything else was tooling and parts so I'm going to say not too bad. So I'm still within the ballpark of my budget for my cam kit (.480 lift if I want to go bigger that's another 70 to $80 for the seal boss cutting tool) and noise timing gear set 👌
I just picked up my original 896 PowerPak heads from the machine shop. 896 heads are a 59cc chamber stock. They installed 2.02 intakes and 1.60 exhaust Manley stainless swirl valves, max flowed each, installed new guides, and they look GREAT! Flow on the intake side is at about 205cfm and the exhaust side is about 138cfm at .500 lift. He spent the most time on these heads for me and the total charge for parts and labor was only $550.00!! Over 1500.00 bucks is a very high price.
That's exactly that point. With the 882 heads we cut the decks until we started cutting the intake valve seat. You can get the chamber any smaller without angle milling the heads, then you get into all kinds of extra costs and issues like the valve angle no longer matching the valve pocket in the pistons. Likewise, putting larger valves in the heads is pointless unless you do some grinding in the ports, and that costs a lot too. Now you are talking about putting crazy money into stock parts.
At 5:30 into the video, the flow bench clearly shows the stock head intake flow curve lay down flat at .400 lift, not even close to the .500 comparison point. I'm sure Dorton knew when he put the 1.94 valves in there that the chamber needed unshrouding, or it would possibly even HURT flow. 1.84s might have done better. But that's probably not even as bad as leaving the exhaust valves stock 1.5 (which made sure they'd look very lame next to the darts.) Still, it's a tribute to old-school Chevrolet manufacturing that these castings could even stand in the same test with a set of 2013 aftermarket castings. Money/time are also confounding and distracting variables in this kind of experiment. Obviously most of your viewers would never dump $1500 into a $50 set of stockers. They'll have something better lying around (like Vortecs) in better shape. So unless you're actively working for Dart, you'd be much more objective just revealing the $$ info at the end, for those interested. That said, thanks very much for the presentation--very clear and informative.
" But that's probably not even as bad as leaving the exhaust valves stock 1.5 (which made sure they'd look very lame next to the darts.)" as a rule of thumb the exhaust valve needs to be 75% of the intake valve. so to figure its proper size on these 882s, multiply the intake valve by .75 and the exhaust only needs to be 1.455". so it is nearly spot on by theory. even the new vortec heads with its good flowing intake ports and 1.94 intake, the 1.5 exhaust is still relevant according to the chevy engineers. too big of an exhaust valve bleeds off cylinder pressure and hurts torque. big block chevys are the most guilty of this proven factor and is why they love static compression.
roknroy1 if you are spinning a lot off the line from the start that kills your top in trap speed.... plus if your rear end ratio is geared very low that will also kill top end speed... I would be more concerned with my ET rather than my trap speed...
Yeah but but Vortecs go flat at 5500 - it's the natue of them ie valve and port size. The Iron Eagles still had another 500rpm in them which to my way of thinking is better if you like to revy yur chevy lol. BTW, I bought a new Vortec roller cam short engine and put some aluminum heads on it for this precise reason. Don't misunderstand me, I think the Vortec head is a great thing for so many reasons, but I like to rev my SBCs to 61-6200rpm and make power up there.
There's no better carburetor than a QJET I have a new one from a company it's call QJET 2 and they have a number 3 for drag racing, mine is a 350 Trw flat top with 186 heads with 1.6 exhaust valves with screw in studs z28 springs and roller tip rocker arm ,tow cam 447 lift runs great in my 2500 4wd.
$1250 for Dart Iron Eagles? Why not just buy some AFR 195s or 185s for $1500 and you will get aluminum cnc machined heads that annihilate the Dart Heads' flow numbers and maintain port velocity.
Except that if they did this level of work to a set of vortec heads it would shit on those 882s and give the darts a run for the money. Its a hell of a lot easier to find good vortec heads too.
Stock worked heads produced: Bottom tq 385@ 3500rpm Peak tq 397@4500rpm 375 tq & hp crossover @5200rpm Peak hp 383 @ 5300rpm... After dart iron eagles: Bottom tq 420 @3500rpm Peak tq 445 @4500rpm 425 tq & hp crossover @5200rpm Peak hp 446 @6100rpm...---- big clues up too with 370 tq vs 445 tq at 6200rpm where better heads maintain power (maintain torque at high rate of revolutions) and stockiest drop off steep after that 6200-6300.
Thanks for doing this so I don't have to find out. This is an amazing format for a video because it really busts the myths. It's also very relatable to a common enthusiast.
Interesting- does anyone remember the small block Chevy 'angle plug' heads from the late 60's or early 70's? I think they were a Chevy performance over the counter head? Supposed to be for higher compression engines back in the day
Should have compared the vortec heads instead of the 882's. Vortec heads are the only stock heads worth using on a gen 1 small block, vastly superior even to the famous "double humps."
I'll rewind and listen for the cam specs. But I only heard him say the cam was a solid flat tapper. No specs; no specific name brand. They need people to proofread and edit through their videos before approving them for public viewing..IMHO
Can't imagine ever using iron heads these days. The flow rates very retro. Really shows how good the new stuff. Even OEM 4vs now that are flowing 250+ cfm stock.
You use them if you run a specific class otherwise, youre right, waster of time. you could buy e streets and a small comp xe or voodoo flat tappet and still make more power
Also forgot to mention that the compression wasn't the same for the shaved 882's vs the aluminum heads an even smaller chamber but for something thrown together for 380 +hp and 390 lb-ft
Fantastic video. I have several sets of 882 heads. Some have either 1.94 or 1.72 intake valves and have gone some porting work on both. Everyone I have ever talked to that has said that they are only good as boat anchors and I am wasting my money on anything I do to them. I can definitely see what they are talking about with this video.
Since everyone gets gm vortecs, get a stock pair clean them and add stainless vavles to some of those! Then compair. Since you can get vortecs between $35 (pick-a-part tuesday special) and $250 any were else.
Get yourself a real pair of aluminum. If you are going stock 23° degree, save the money and get some procomps, pay for a good port job. If you are going all out 18° The sky is the limit. There are guys porting the cheap procomps making more power than $2000 AFR heads.
tommy treadaway Because it seems most people who watch pay attention, within 30 seconds I noticed he never mentioned what kind of chevy heads they were so he could have some absolute shite ones like 624's
Ken this test was done with flat tops from the video.... you can run 64cc heads and flat tops... most dart ie 64cc heads measure out to really be 65-68cc...mine measured at 65.5 and the 5cc speed pro pistons actually measured 6cc reliefs....with a larger duration cam to bleed of some of the compression at lower rpms and lower the dcr it will run great. Especially with the newer chamber design.
Back in 1993, when i was in my early twenties, i took the same pair of GM 882 heads, had them ported, polished, went with stainless steel valves, kept the 1.94 for the intake, but went 1.60 on the exhaust, screw in studs, bolted to a freshly rebuilt 4bolt mains 350cid bored .030 over, with four valve relief flatop hyperutectic pistons, stock 5.7 rods, single pattern comp cams hydraulic 270(224@.050/110ls/.470 int&exh), comp cams 1.52 roller tip rockers, ARP bolts throughout the entire engine, eldelbrock rpm dual plane intake, holley 3310 750cfm vacuum secondary carburator, msd6a/hei ignition, 1 5/8'' headman headers, 2 1/2'' dual exhaust, flowmaster dual chamber mufflers with tailpipes to rear bumper, rebuilt stock th350 with b&m shift kit for firmer shifts, b&m 2000rpm stall 12'' torque converter and a 4:10 10bolt positrac rearend, neadless to say, this combo might not have been ideal and a total waste of money when it came to the modified work on the heads, given the better alternatives at the time, but it netted me consistant 14.40s in the 1/4mile in a 1975 chevelle 2dr, all engine... it was my very first street/strip car, so it was a learning process, and it didnt dissapoint.
That's awesome. I've always felt that if you built it and you can enjoy it, there's no engine that's a waste of money -- even if you could have made more power cheaper.
Back in the early 70's I was building a sleeper so I sent a set of power pack heads, as they were known then, to AFR. They were able to spec them out slightly superior to the fuelie head numbers. I also had the good fortune to be working in an automotive machine shop at the time. I came across a 350 "X" block that I was able to bore and stroke to 388 CID. Used all the then popular parts, Jahn's pistons, Crower camshaft, Mallory ignition etc... I was able to make a 1963 Chevy II into a raging monster pushing that little shoe box into the low 10's. I realize today that low 10's are anemic but back then it was highly impressive as Pro Stock cars were only in the low 9's. Never put it on the dyno but I'm guessing it was making a skosh over 550 HP. Just pointing out that it is possible to use these heads and make good power but today it is not economically feasible. Back then you used what you had or could find at a reasonable price. If you wanted to put a blower on your car, for instance, there weren't any "kits" you could buy so you had to search the wrecking yards for a 471 or 671 blower of a diesel truck and machine it to make it fit a small block. With the technology today it is easier to make big power but it's still expensive. Gotta say though, as a G-force junkie, more fun than should be allowed. Peace out and happy racing.
How about using a set of L98 Corvette aluminum heads? I'd be curious as to how those would compare to the aftermarket aluminums. Since you can get those for around $350-$400 off of Ebay.
They have good port velocity and work well on the street and make good torque, but vortec's beat them for flow above mid lift and for swirl. vortec's win the HP/$ comparison. Chevy High Performance did a dyno comparison and I'm paraphrasing them.
. -113's stock aluminum heads max at about 390 HP and are tricky to port to get more out of... but a good bump up in power and MPG from stock LoPo 76cc chamber heads... and save 50 lbs... aluminum intake and water pump save another 50 lbs. off front of car...
they could have put some thicker head gaskets on the Dart to make the compression equal. Not that it matters, they should have used Vortec as many have noted and probably a better aftermarket head as well.
It's a good test for newbies to the SBC. Back in the '90s I remember learning just how much stock Chevy heads suck. Aftermarket heads are the only way to go once you're set on rebuilding a 350 for reliability or performance. Thanks for the video.
Solid cam 248/252 (advertised) with about half inch lift, solid flat tappet, 350 ci sbc, scat moly slugs (don't know if flat top) scat crank. 1&¾ headers from Dyno setup.
What about a milder engine with dual plane, mild to mid street hydraulic with .460 or .480 lift, smaller tube headers with the stockers against a smaller port Eagle. I am thinking about a "torqueyer" street engine (350) which uses the better velocity of the stock heads rather than just the flow.
I wander what the Chevy heads would produce with a fully ported job would have result because we all know the dart runners are casted that size to start with I don't think this is a fair comparison port the ,882 heads and Dyno again I am just curious how much power a stock set of heads will produce
should have tested against vortec.. would be much better comparison as combustion chambers are similar modern design and would have been same compression
Vortecs are good heads but the test was to see which head made better power for the money. If you are going to switch to a set of vortec heads it will also require a new intake and exhaust so it is always going to be more money than necessary. The best time to go with Vortecs is if you already have the intake.
Agreed, but if you have to buy an intake to match your mods, junk yard vortecs cleaned up good power, I would bet at least competitive. As where these compression lacking, horrible combustion chamber 882's that many classes mandate to LIMIT horsepower. For the money, I have setup up a few smallblocks with some of the smaller lift rule cams and made over 400hp with vortecs. 400 dollar total investment in heads. :) That is good for the dollar. Not trying to be rude.
ssswww That's not rude at all. You are right that the Vortecs make good power. But like you said, it assumes you can also get the intake and exhaust headers cheap.
Great video. I used to do that type of machine work on heads because years ago off the shelf cylinder heads did not exist at all so that’s what we did. These off the shelf dart heads you can’t beat them, and the hours porting and polishing what a mess
So even a 1970 350/300 10.25:1 compression head isn't worth doing anything with, I would still have to do most all the same things as the 882 head? I do figure them to be 1.94/1.60, since they are the 300hp heads...
882 heads make good boat anchors. Dart makes a decent head but how to they compare to the Vortec Head? A few hundred more will get you into AFR Heads which are in a different league. (Next to the Darts)
This is just what ive been looking for. I have an old C10 with a 350 and its just a cruiser, i dont want to put a converter and gears in it and spin the motor to 6000 rpm. I just want to maximize the power from idle to 3500 rpm where the engine spends all its time and i figured cylinder heads weren't really gonna do anything for me in that range. This confirmed that suspicion! Ill just toss some headers and a small cam in it and call it a day.
I had that same 882 head on sbc small block and it lasted over a year running hard I had.510 lift camshaft and. Around 300 or so up never broke anything in valve train. That cylinderhead you just shown dart should be better next engine I do im going to look at those heads thanks for showing those other heads.
I love the test, I would just say if you are going stick with the SBC, go for the aluminum versions, they save close 50lbs. That will yield a slight improvement in handling plus that much less mass for your car. One problem is though for the cost of those heads you could pick up a used LS2 for about the same amount. That's going to make more power throughout the rev range, less likely to leak oil, and weighs over 150lbs less. Sure it's not as easy on the eyes I get that but the smiles from inside the car will be greater.
You can pickup the ECU and harness at the salvage yard with the motor for ~$1200, oil pan, mounts and new fuel pump is around $500. I'm not sure I consider that a lot of money, but that's subjective. Even if you go with getting a conversion kit, it's only about $1200 and the cost of the LS. So yeah it's more expensive but it's not really that much. Now if you are going the crate route with a new motor and new everything sure but that's not really needed.
To get a big boost in hp you need to up the compression to over 10-1, or 11-1..you can't get hp with 8-1 or 8.5. I can remember in the 60's they were running 13-1.
Hey Derrick. Loved the episode on rebuilding the 307. Just a couple of questions. Did you use new cam bearings on the block or leave the originals in there. Also, the new bearings you used for the main bearings and rod bearings, were they 10 thousands under or stock size? Also, were the rings the same size as stock or 10 thousands over? Love all your episodes. Keep them coming.
If you do a full race Port from the intake Port all the way to the bowl with a valve sets you will see a big difference problem is ... hardly anybody would be willing to do that
20 years ago it was cheaper to port your own and rebuild them. Everyone bitches about jobs in China, but your dollar goes a lot farther (with some stuff) than it used to.
LOL, so true, i think I have seen ported 305 heads flow better and the new question is who build gen1 sbc/f/m anymore, everyone turning to swapped takeouts...
AFR Cylinder heads is overrated... To expensive for so small gain... I know a guy that with cheap money build hes own 500+ smallblock chevy. But he did buy bare chinese fake afr heads and bought the rest from afr. I think he said he save atleast 2000 dollars. And yes the engine still runs today but in another car.
Patrik Nilsson you’re full of shit. Ran a dyno on a 383 sbc with pro-comp 210cc junk and only managed a measly 405hp. They font flow air, the intake runner is garbage.
@@jrod264winmag well if i am a liar! Well then you are the one that is a loser that buy engine part for thousands of dollars and still get 400 hp... You must doing something serious wrong! With my concept i get over 500 horsepower! And with only 195cc... You cant run 210cc heads on a smallblock and think you will get alot of horsepower. It get to much air in that cant get out and you chocking the engine... Simple math air in air out
That's like an advertisement for DART, what head do you think they would have chosen to compare against? Let's see...if you were going to show off in a foot race would you choose to compete against the fat kid or the athletic guy? Maybe try comparing the iron eagles against a head that someone would actually pay to have re-built. 882s...LOL
or just buy some already built ones for $600 used. You just need to inspect and prob an hour at the shop to clean them up $700-750 total. Theres tons of half built projects on craigslist
Bought a very clean set of 823 castings l98 heads with rockers for $650,,,, and sold my used Dart Iron Eagles 215 /64cc for a $1000. No more first generation Sbc for me as I go forward,,,,, just LS swap it,,, lol
To bad I have a set of 186 69 Camaro hump heads I just been redone with port polish and springs good to just over 600 lift I would have loaned them just to see what they could do.
you can get much closers numbers from the stock head if they had bought the darts at 68-70cc. lowered compression on big displacement is a huge loss all over the map on top of longer cnc machined runners.
You could have milled them down to 62 or 64cc I've done it make it fair . 193 at 500 lift at 28in .,I don't think that's right. Chevy has made plenty other heads you could have compared them to.
Ok good video and what does the stock L31 vortec heads stack up against the Dart Iron Eagle,,, vortec heads are cheap new,, can we see a comparison. Dart heads are a hot rod head designed to make power,, the stock chevy vortec heads were simply a production thing that hot rodders picked up on,, I have an old 400 +060 with vortecs curiouse to see
A more true comparison would be Dart head against a Vortec 062 with the fast burn chamber because the Dart head has the fast burn chamber and that makes the head really flow well. They try to sell Dart heads by throwing off on stock heads but they don't tell you that a Vortec head can make as much as 480 hp and costs around $350.00 per pair used and in good shape.
I have a pair of these Dart heads sitting on top of a .030-over 350. They do pretty well for the $900 I paid for them. But for $1200+, I'd go for Trick Flow or even Dart's aluminum heads.
Out of the box heads are never really right though. U have to lap the valves in the least. Sometimes valves can be so off that u need to grind seats. Entire angles might be off. Check for yourself.
The narrator says you can't get those heads I seen quite a few heads on eBay for 152 hundred $300 you can get a pair and they may not get the guys but if they do you do what you do because you want to call them have the most horsepower and fuelly heads really do the trick
I have a set of Dart Motown heads ported! What do you think of the Motown heads and how do you think they will do on a L79 sb 327! It's a original bottom end that had a original 20,000 miles!!!!
180cc heads that flowing more then 180cc is that common? i just got set of there 180cc heads but with 2.05 in and 1.60ex 49cc chamber . r they going be same abouts flow rate ?
has anyone done comparison dyno tests on the different sized iron eagles on the same shortblock ? ? 180 cc , 200 cc , 215 cc , 230 cc . i'm just wondering how much hp difference there is with the small iron eagle vs the largest one ? or even flow comparison of each ? not factory advertised numbers but real world numbers by non biased head porters
. Why did they only go 1.94/1.50 valves on the Chevy 882 heads? I thought they had the same valve separation distance as the stock big 'Fuely' valve 2.02/1.60 heads? Looks to have started with small valve/small port 'truck' -882 heads instead of 'car' -882 heads which already come with the valves sizes they enlarged to and have bigger ports and as stock outflow these reworked heads... Also, compression ratio not the same with -882 69cc vs Iron Eagle 64cc chambers... Instead of expensive, dangerous (chance of cracking/leaking) milling of -882 heads, I'd simply use domed pistons for higher compression ratio...Finally, I'd expect 500 HP if using a huge for the street 248/252 cam... That cam is way too big for -882 heads and even too big for the 180cc Iron Eagle heads...
I agree that they chose the wrong heads to compete with, they should have used the 041x,492 ,186,291 just like what the other guy texted that this is a dart advertisement to sell their head if you really search you can find the castings I posted check out Craigslist,yard sales, machines shops,and just asking and looking around but if you have the money for an after market head then bye it.its also all about what do you want to do with your motor and what kind of power your looking for
i just give a set of 194 camel hump heads away for free but i just got 2 454 strokers one with only 6000 miles on it the other one has 38000 on it both with the heavy duty 400 turbo that is the cheap stuff i got for free so far this year i just love the 4x4 short box pu 79 chevy with under 36,000 miles on it factory paint is still in mint condition
do you think doing this test with a set of 906 or 062 vortec heads would have made a difference, those are supposed to be the best factory production head Chevy made. ..or would it not make a difference because you sent those 882s threw every step possible ..I just wonder how the vortec heads would line up vs these 2 sets after its been threw all these steps
It is always interesting to see, that torque scales LINEARLY with the flow cfm of the cylinder head (regarding same intake runner size in cc, which is important, because otherwise you once again play around with the rev band, like with camshafts, too). So comparing modern heads, which can flow up to 250 cfm, porting them slightly, which can obtain up to 280~300 cfm if you know what you do, you will just gain DOUBLE the power comparing to a stock 70s chevy iron head, which does about 150cfm. You can gain easily 300 horsepower instead of 170, with a stock cam. With a smooth idle, with a good gas mileage, with just pulling the heads and replacing them, which can easily be done in-car without a full engine overhaul. (Just remind: You might f*** your bearings and piston rings then ..... hahaha)
fanghicheck I'm with ya bud, give me a set of 2.02 camel humps, with gasket match and light debuting polish best bang for your buck on old school small blocks, GM engineers back in the day were pretty much on the ball ,not saying there isn't a better head just saying the old school factory camel humps work great for what they were designed to do.
I wish you guys could have gotten ahold of some double hump heads for comparison..i do agree they are hard to come by especially in stock form...I am an electrician in Virginia and I recently acquired a set of stock, un molested, 461 casting double hump heads.. I got them in trade for doing some electrical work for a fella...they came off a vette and I believe he said they were rated at 375 hp? not sure myself but are they worth getting worked over? if so I would like to use them on a 4 bolt main 350 I have that I plan on installing in my 1973 AMC gremlin... your thoughts would be appreciated!!
If you have a set of untouched double hump heads, you might want to consider selling those bad boys. Street stock oval track racers are always looking for double humps because those are the best when the rulebook says something like "stock only, no Vortec." If you are building a street motor you can probably get enough out of them for a new set of cheap aftermarket heads that are going to be ready right out of the box and give you comperable or better power.
+The Horsepower Monster "aftermarket heads that are going to be ready right out of the box" Are you kidding me? Are you telling me that ppl should mount these heads right out of the box? PLZ take youre new heads to the workshop at let them take a look at them before you do anything and always be ready to spend more money on valve jobbs and bowl bleending. I remember my new Edelbrook RPM heads, they looked like shit when i got em!!
Wait wait wait the biggest valve you can fit in an 882 head is a 1.94 intake? Because Im pretty sure I have a set that has 2.02 intake and 1.60 exhaust and when I bought the heads they had 1.94 int and 1.50 exhaust
ryan ishee the L82 and the z28 I think in 1973 to the early 1980ies had the big valve 882 heads .I have a 1976 L82 vette which I purchased in 1980 and still have when I rebuilt and moded in 88 it had 882 with 2.02 and 1.60 I have the heads on the car today along with a street supercharger it makes great power hp and torque with other mods
This content right here is EXACTLY what I like to watch.
This is true, I bought a set of 062 vortec heads, and after doing all the work my self and buying all the tools I bought to work the heads I ended up spending more than buying some nice brodix heads ( not to mention the headaches). The best part of doing the work myself was learning how to do it.
Yes but you can always use those tools to do other heads
Ehh I'm currently doing a set of 906's myself. I surface them on my mill myself, back cut the valves, pocket ported, gasket matched, lapped the valves, new seals, stud kit, offset retainers, beehive springs, goodson alumi check all for just under $350. Now a hundred of that was the purchase of the heads themselves everything else was tooling and parts so I'm going to say not too bad. So I'm still within the ballpark of my budget for my cam kit (.480 lift if I want to go bigger that's another 70 to $80 for the seal boss cutting tool) and noise timing gear set 👌
I just picked up my original 896 PowerPak heads from the machine shop. 896 heads are a 59cc chamber stock. They installed 2.02 intakes and 1.60 exhaust Manley stainless swirl valves, max flowed each, installed new guides, and they look GREAT! Flow on the intake side is at about 205cfm and the exhaust side is about 138cfm at .500 lift. He spent the most time on these heads for me and the total charge for parts and labor was only $550.00!! Over 1500.00 bucks is a very high price.
You are right. As long as you are happy with what you've got, that's all that matters. Hope your engine runs like a champ!
That's exactly that point. With the 882 heads we cut the decks until we started cutting the intake valve seat. You can get the chamber any smaller without angle milling the heads, then you get into all kinds of extra costs and issues like the valve angle no longer matching the valve pocket in the pistons. Likewise, putting larger valves in the heads is pointless unless you do some grinding in the ports, and that costs a lot too. Now you are talking about putting crazy money into stock parts.
At 5:30 into the video, the flow bench clearly shows the stock head intake flow curve lay down flat at .400 lift, not even close to the .500 comparison point. I'm sure Dorton knew when he put the 1.94 valves in there that the chamber needed unshrouding, or it would possibly even HURT flow. 1.84s might have done better. But that's probably not even as bad as leaving the exhaust valves stock 1.5 (which made sure they'd look very lame next to the darts.) Still, it's a tribute to old-school Chevrolet manufacturing that these castings could even stand in the same test with a set of 2013 aftermarket castings.
Money/time are also confounding and distracting variables in this kind of experiment. Obviously most of your viewers would never dump $1500 into a $50 set of stockers. They'll have something better lying around (like Vortecs) in better shape. So unless you're actively working for Dart, you'd be much more objective just revealing the $$ info at the end, for those interested.
That said, thanks very much for the presentation--very clear and informative.
" But that's probably not even as bad as leaving the exhaust valves stock 1.5 (which made sure they'd look very lame next to the darts.)"
as a rule of thumb the exhaust valve needs to be 75% of the intake valve. so to figure its proper size on these 882s, multiply the intake valve by .75 and the exhaust only needs to be 1.455". so it is nearly spot on by theory. even the new vortec heads with its good flowing intake ports and 1.94 intake, the 1.5 exhaust is still relevant according to the chevy engineers. too big of an exhaust valve bleeds off cylinder pressure and hurts torque. big block chevys are the most guilty of this proven factor and is why they love static compression.
Isn't that the point? They won't perform even spending the money. 😕
only problem here is a stock set of chevy vortes heads flow around 230 to 240 cfm ... those would have shown a real comparison!
could only get 107mph in 3300lb car with a 406 vortec
Mick Sexton Driver mod☝️
I expected more out of the darts..them old 882 held up good
roknroy1 if you are spinning a lot off the line from the start that kills your top in trap speed.... plus if your rear end ratio is geared very low that will also kill top end speed... I would be more concerned with my ET rather than my trap speed...
Yeah but but Vortecs go flat at 5500 - it's the natue of them ie valve and port size. The Iron Eagles still had another 500rpm in them which to my way of thinking is better if you like to revy yur chevy lol.
BTW, I bought a new Vortec roller cam short engine and put some aluminum heads on it for this precise reason.
Don't misunderstand me, I think the Vortec head is a great thing for so many reasons, but I like to rev my SBCs to 61-6200rpm and make power up there.
5:05 - thats a heck of a nice ridge/step left in the throats of the Dart iron eagle heads! Intake and exhaust need some time with a stone burr
I saw a NHRA "Stock" 1974 350 make 437hp at 6500rpm on a dyno with "stock" 882 heads and stock intake & Q-jet. Must be magic.
Bullshit
@@wes6374 Your an idiot. Look into it for yourself.
@@wes6374 There are several videos of them here on utube on a dyno.
The money and tricks that go into an NHRA Stock engine is astounding! The head work is crazy!
There's no better carburetor than a QJET I have a new one from a company it's call QJET 2 and they have a number 3 for drag racing, mine is a 350 Trw flat top with 186 heads with 1.6 exhaust valves with screw in studs z28 springs and roller tip rocker arm ,tow cam 447 lift runs great in my 2500 4wd.
Installed several sets of these, they come set up w/correct accy. Patterns + accepts int. & ext. Bolt valve covers. Saves $$$ & time.
AFR all the way. Made 552 hp on a 383 with the 195cc heads with a port matched AFR intake and roller cam.
Yeah I have a 434 stroker from skip white performance with a pro charger 760 hp to the rear tires wouldn’t trade it for the world
$1250 for Dart Iron Eagles? Why not just buy some AFR 195s or 185s for $1500 and you will get aluminum cnc machined heads that annihilate the Dart Heads' flow numbers and maintain port velocity.
You got it right.
Some tracks don't allow aluminum heads in certain classes, while I don't think I've ever seen a cast iron head restriction
Because they are doing a price comparison of machining the stock cast iron heads and final dyno test results to see if its worth spending the time
Except that if they did this level of work to a set of vortec heads it would shit on those 882s and give the darts a run for the money. Its a hell of a lot easier to find good vortec heads too.
David Cheeseman cheese man it's about trade craft
Stock worked heads produced:
Bottom tq 385@ 3500rpm
Peak tq 397@4500rpm
375 tq & hp crossover @5200rpm
Peak hp 383 @ 5300rpm...
After dart iron eagles:
Bottom tq 420 @3500rpm
Peak tq 445 @4500rpm
425 tq & hp crossover @5200rpm
Peak hp 446 @6100rpm...---- big clues up too with 370 tq vs 445 tq at 6200rpm where better heads maintain power (maintain torque at high rate of revolutions) and stockiest drop off steep after that 6200-6300.
Had Iron Eagles on my 355 paired with a 292H cam and 3000 stall… Thing was fun
Thanks for doing this so I don't have to find out. This is an amazing format for a video because it really busts the myths. It's also very relatable to a common enthusiast.
Hey, thanks!
Interesting- does anyone remember the small block Chevy 'angle plug' heads from the late 60's or early 70's? I think they were a Chevy performance over the counter head? Supposed to be for higher compression engines back in the day
jim dandy I had em... they were awesome
292 turbo heads. I had a set on 55 Chevy 377 with roller cam and 2 750 holleys. A friend has them sitting in his garage won't sell them back to me.
Should have compared the vortec heads instead of the 882's. Vortec heads are the only stock heads worth using on a gen 1 small block, vastly superior even to the famous "double humps."
Those are the best head's I've ever seen!Dart definitely figured out the head's!
It might help if you included the cam specs and cubic inches for this engine.
and revealed the static compression ratio for the engine with both sets of heads......as one head had 4 cc + more chamber volume
I'll rewind and listen for the cam specs. But I only heard him say the cam was a solid flat tapper. No specs; no specific name brand. They need people to proofread and edit through their videos before approving them for public viewing..IMHO
@@titolombre7004 Try listening.
Can't imagine ever using iron heads these days. The flow rates very retro. Really shows how good the new stuff. Even OEM 4vs now that are flowing 250+ cfm stock.
You use them if you run a specific class
otherwise, youre right, waster of time. you could buy e streets and a small comp xe or voodoo flat tappet and still make more power
I love tests like this. How about comparing all the popular after market heads?
Are they faster if you paint them chevy orange ?
And you and stickers and racing stripes but don't add flames they make your car so fast it's undriveable
im doin a 67 327 w/ stock valves lil porting on the exgaust nothing fancy. ls6 springs comp retainers holley 650 dp summit stg 3 intake 1" spacer hooker. headers. lt 1.5 comp rocker tips
Also forgot to mention that the compression wasn't the same for the shaved 882's vs the aluminum heads an even smaller chamber but for something thrown together for 380 +hp and 390 lb-ft
Well 3cc isn't much difference and they could've made that up in the head gasket itself which is probably what they done to make the comparison equal
Fantastic video. I have several sets of 882 heads. Some have either 1.94 or 1.72 intake valves and have gone some porting work on both. Everyone I have ever talked to that has said that they are only good as boat anchors and I am wasting my money on anything I do to them. I can definitely see what they are talking about with this video.
Since everyone gets gm vortecs, get a stock pair clean them and add stainless vavles to some of those! Then compair. Since you can get vortecs between $35 (pick-a-part tuesday special) and $250 any were else.
They crack.
Uhhh, no, that's not really an issue with vortec heads.
Get yourself a real pair of aluminum. If you are going stock 23° degree, save the money and get some procomps, pay for a good port job. If you are going all out 18° The sky is the limit. There are guys porting the cheap procomps making more power than $2000 AFR heads.
@@donrutter6765 dont waist money on 18* heads. Just buy Sb2 heads. You can adapt them to a dart shp block.
I don't understand how this channel only has 8,000 subs
tommy treadaway Because it seems most people who watch pay attention, within 30 seconds I noticed he never mentioned what kind of chevy heads they were
so he could have some absolute shite ones like 624's
***** @ 1:07 he says what heads they are
Kyle Parker Stand corrected but still kind of a shite video
Ken this test was done with flat tops from the video.... you can run 64cc heads and flat tops... most dart ie 64cc heads measure out to really be 65-68cc...mine measured at 65.5 and the 5cc speed pro pistons actually measured 6cc reliefs....with a larger duration cam to bleed of some of the compression at lower rpms and lower the dcr it will run great. Especially with the newer chamber design.
Back in 1993, when i was in my early twenties, i took the same pair of GM 882 heads, had them ported, polished, went with stainless steel valves, kept the 1.94 for the intake, but went 1.60 on the exhaust, screw in studs, bolted to a freshly rebuilt 4bolt mains 350cid bored .030 over, with four valve relief flatop hyperutectic pistons, stock 5.7 rods, single pattern comp cams hydraulic 270(224@.050/110ls/.470 int&exh), comp cams 1.52 roller tip rockers, ARP bolts throughout the entire engine, eldelbrock rpm dual plane intake, holley 3310 750cfm vacuum secondary carburator, msd6a/hei ignition, 1 5/8'' headman headers, 2 1/2'' dual exhaust, flowmaster dual chamber mufflers with tailpipes to rear bumper, rebuilt stock th350 with b&m shift kit for firmer shifts, b&m 2000rpm stall 12'' torque converter and a 4:10 10bolt positrac rearend, neadless to say, this combo might not have been ideal and a total waste of money when it came to the modified work on the heads, given the better alternatives at the time, but it netted me consistant 14.40s in the 1/4mile in a 1975 chevelle 2dr, all engine... it was my very first street/strip car, so it was a learning process, and it didnt dissapoint.
That's awesome. I've always felt that if you built it and you can enjoy it, there's no engine that's a waste of money -- even if you could have made more power cheaper.
75 chevelle, p u
But the real question is? Can Dorton make those Iron Eagle heads even better than straight outta the box? If so,how much is the MAX #&$?
I look for Torque below 5000 rpm but starting at 1000 rpm !
No racing just street throttle response !
I don't think your comparison was fair because you started out with boat anchors from Chevrolet. A pair of Vortec heads would have been more in line.
Vortec heads put most aftermarket street heads to shame.
@@falcon6995 The EQ vortec heads have a shyt ton of room for porting and bigger valves too.
That's remarkable because when Dart first introduced the Iron Eagle series heads many years ago, they advertised a 75hp advantage over stock heads
Back in the early 70's I was building a sleeper so I sent a set of power pack heads, as they were known then, to AFR. They were able to spec them out slightly superior to the fuelie head numbers. I also had the good fortune to be working in an automotive machine shop at the time. I came across a 350 "X" block that I was able to bore and stroke to 388 CID. Used all the then popular parts, Jahn's pistons, Crower camshaft, Mallory ignition etc... I was able to make a 1963 Chevy II into a raging monster pushing that little shoe box into the low 10's. I realize today that low 10's are anemic but back then it was highly impressive as Pro Stock cars were only in the low 9's. Never put it on the dyno but I'm guessing it was making a skosh over 550 HP. Just pointing out that it is possible to use these heads and make good power but today it is not economically feasible. Back then you used what you had or could find at a reasonable price. If you wanted to put a blower on your car, for instance, there weren't any "kits" you could buy so you had to search the wrecking yards for a 471 or 671 blower of a diesel truck and machine it to make it fit a small block. With the technology today it is easier to make big power but it's still expensive. Gotta say though, as a G-force junkie, more fun than should be allowed. Peace out and happy racing.
I have iron eagle 215s on my 350. They're damn good heads. They put me over 600hp NA and pull strong well past 8000 rpms
How about using a set of L98 Corvette aluminum heads?
I'd be curious as to how those would compare to the aftermarket aluminums.
Since you can get those for around $350-$400 off of Ebay.
those heads don't even flow as well as vortec's ....
They have good port velocity and work well on the street and make good torque, but vortec's beat them for flow above mid lift and for swirl. vortec's win the HP/$ comparison. Chevy High Performance did a dyno comparison and I'm paraphrasing them.
. -113's stock aluminum heads max at about 390 HP and are tricky to port to get more out of... but a good bump up in power and MPG from stock LoPo 76cc chamber heads... and save 50 lbs... aluminum intake and water pump save another 50 lbs. off front of car...
I would like to know the best aluminum heads for a sbc 383. Have world products cast heads now. Running flat top pistons. Flat tappet cam comp xe284h
I wonder how the Edelbrock Performer RPM heads would compare against the Iron Eagles?
nandoGdog Better but if you want real power, you spend the money for a reputable porter to fix them.
my 1978 z-28 Camara had a smog whopping 165 hp.
Didmt know Kodak made engines.
they could have put some thicker head gaskets on the Dart to make the compression equal. Not that it matters, they should have used Vortec as many have noted and probably a better aftermarket head as well.
The driving torque is unreal; will try a set of the Dart heads on the next build.
It's a good test for newbies to the SBC. Back in the '90s I remember learning just how much stock Chevy heads suck. Aftermarket heads are the only way to go once you're set on rebuilding a 350 for reliability or performance. Thanks for the video.
99
99
Kk9kkkk9kkk
Solid cam 248/252 (advertised) with about half inch lift, solid flat tappet, 350 ci sbc, scat moly slugs (don't know if flat top) scat crank. 1&¾ headers from Dyno setup.
Also I heard the cam numbers but what cam? Hydraulic roller, hydraulic flat tappet? Solid flat tappet?
Solid flat tappet. At the time I was testing stock car racing components on it. Thanks for watching.
sbc 441 heads are a good choice for a budget street head .
I used to run those... Now I stick to 062's
What about a milder engine with dual plane, mild to mid street hydraulic with .460 or .480 lift, smaller tube headers with the stockers against a smaller port Eagle. I am thinking about a "torqueyer" street engine (350) which uses the better velocity of the stock heads rather than just the flow.
This is the kind of advert that I don't mind at all!
im learning just how much power can be gained from better heads CFM
I wander what the Chevy heads would produce with a fully ported job would have result because we all know the dart runners are casted that size to start with I don't think this is a fair comparison port the ,882 heads and Dyno again I am just curious how much power a stock set of heads will produce
But you didn't run a vortex head why
should have tested against vortec.. would be much better comparison as combustion chambers are similar modern design and would have been same compression
Vortecs are good heads but the test was to see which head made better power for the money. If you are going to switch to a set of vortec heads it will also require a new intake and exhaust so it is always going to be more money than necessary. The best time to go with Vortecs is if you already have the intake.
Agreed, but if you have to buy an intake to match your mods, junk yard vortecs cleaned up good power, I would bet at least competitive. As where these compression lacking, horrible combustion chamber 882's that many classes mandate to LIMIT horsepower.
For the money, I have setup up a few smallblocks with some of the smaller lift rule cams and made over 400hp with vortecs. 400 dollar total investment in heads. :)
That is good for the dollar. Not trying to be rude.
ssswww That's not rude at all. You are right that the Vortecs make good power. But like you said, it assumes you can also get the intake and exhaust headers cheap.
Great video. I used to do that type of machine work on heads because years ago off the shelf cylinder heads did not exist at all so that’s what we did. These off the shelf dart heads you can’t beat them, and the hours porting and polishing what a mess
Thanks! And thanks for watching!
So even a 1970 350/300 10.25:1 compression head isn't worth doing anything with, I would still have to do most all the same things as the 882 head? I do figure them to be 1.94/1.60, since they are the 300hp heads...
882 heads make good boat anchors. Dart makes a decent head but how to they compare to the Vortec Head? A few hundred more will get you into AFR Heads which are in a different league. (Next to the Darts)
This is just what ive been looking for. I have an old C10 with a 350 and its just a cruiser, i dont want to put a converter and gears in it and spin the motor to 6000 rpm. I just want to maximize the power from idle to 3500 rpm where the engine spends all its time and i figured cylinder heads weren't really gonna do anything for me in that range. This confirmed that suspicion! Ill just toss some headers and a small cam in it and call it a day.
I had that same 882 head on sbc small block and it lasted over a year running hard I had.510 lift camshaft and. Around 300 or so up never broke anything in valve train. That cylinderhead you just shown dart should be better next engine I do im going to look at those heads thanks for showing those other heads.
Those Dart Iron eagles are more expensive that Brand New Vortec heads.
factor in a new intake and valve covers etc too because for a person with an existing gen I 350 its more parts you gotta buy.
I love the test, I would just say if you are going stick with the SBC, go for the aluminum versions, they save close 50lbs. That will yield a slight improvement in handling plus that much less mass for your car.
One problem is though for the cost of those heads you could pick up a used LS2 for about the same amount. That's going to make more power throughout the rev range, less likely to leak oil, and weighs over 150lbs less. Sure it's not as easy on the eyes I get that but the smiles from inside the car will be greater.
You can pickup the ECU and harness at the salvage yard with the motor for ~$1200, oil pan, mounts and new fuel pump is around $500. I'm not sure I consider that a lot of money, but that's subjective. Even if you go with getting a conversion kit, it's only about $1200 and the cost of the LS. So yeah it's more expensive but it's not really that much. Now if you are going the crate route with a new motor and new everything sure but that's not really needed.
Cam and short block specs please!
To get a big boost in hp you need to up the compression to over 10-1, or 11-1..you can't get hp with 8-1 or 8.5. I can remember in the 60's they were running 13-1.
but of course sunoco sold pump gas with 105 octane.
What do you mean the cam is pretty standard ? 248/252 is a huge cam ?
Hey Derrick. Loved the episode on rebuilding the 307. Just a couple of questions. Did you use new cam bearings on the block or leave the originals in there. Also, the new bearings you used for the main bearings and rod bearings, were they 10 thousands under or stock size? Also, were the rings the same size as stock or 10 thousands over? Love all your episodes. Keep them coming.
Who rebuilds 882 smog heads.
T salinger1026. I ported a set and shaved .060 off em and they ran awesome!!!
If you do a full race Port from the intake Port all the way to the bowl with a valve sets you will see a big difference problem is ... hardly anybody would be willing to do that
20 years ago it was cheaper to port your own and rebuild them. Everyone bitches about jobs in China, but your dollar goes a lot farther (with some stuff) than it used to.
LOL, so true, i think I have seen ported 305 heads flow better and the new question is who build gen1 sbc/f/m anymore, everyone turning to swapped takeouts...
I'll take AFR heads over Dart even if they cost twice as much....
You won't gain anything
NUKE The CCP that’s so not true 😂
AFR Cylinder heads is overrated... To expensive for so small gain... I know a guy that with cheap money build hes own 500+ smallblock chevy. But he did buy bare chinese fake afr heads and bought the rest from afr. I think he said he save atleast 2000 dollars. And yes the engine still runs today but in another car.
Patrik Nilsson you’re full of shit. Ran a dyno on a 383 sbc with pro-comp 210cc junk and only managed a measly 405hp. They font flow air, the intake runner is garbage.
@@jrod264winmag well if i am a liar! Well then you are the one that is a loser that buy engine part for thousands of dollars and still get 400 hp... You must doing something serious wrong! With my concept i get over 500 horsepower! And with only 195cc... You cant run 210cc heads on a smallblock and think you will get alot of horsepower. It get to much air in that cant get out and you chocking the engine... Simple math air in air out
I run the alum pro1 230 on my 427sbc good heads. if you go stock you will have to machine them
That's like an advertisement for DART, what head do you think they would have chosen to compare against?
Let's see...if you were going to show off in a foot race would you choose to compete against the fat kid or the athletic guy?
Maybe try comparing the iron eagles against a head that someone would actually pay to have re-built. 882s...LOL
causeimbatmaaan seriously. they should have chosen Vortec or camel hump heads to compete against the iron eagles. not lousy ass 882 heads
causeimbat
441 heads, but they are rare were supposedly the best stock heads.
or just buy some already built ones for $600 used. You just need to inspect and prob an hour at the shop to clean them up $700-750 total. Theres tons of half built projects on craigslist
Richard Sanford I
Bought a very clean set of 823 castings l98 heads with rockers for $650,,,, and sold my used Dart Iron Eagles 215 /64cc for a $1000. No more first generation Sbc for me as I go forward,,,,, just LS swap it,,, lol
😂😂😂
To bad I have a set of 186 69 Camaro hump heads I just been redone with port polish and springs good to just over 600 lift I would have loaned them just to see what they could do.
If they've been ported the fuelie heads probably would be very much in comparison to what the dart heads ran horsepower and torque wise.
Was it an illusion the crossover looked a different RPM on eagle heads. It might be the camera giving the wrong impression.
you can get much closers numbers from the stock head if they had bought the darts at 68-70cc. lowered compression on big displacement is a huge loss all over the map on top of longer cnc machined runners.
Do you think they make a set for a 4.8 liter Chevy and if so is it basically just a plug-in play??? out with the old in with the new???
You could have milled them down to 62 or 64cc I've done it make it fair . 193 at 500 lift at 28in .,I don't think that's right. Chevy has made plenty other heads you could have compared them to.
but the 882 is the most common boat anchor lol
Excellent comparison. I just watched it again today. I appreciate all of the good work you put into sharing it with us.
Thanks!
to remove studs i put a small pice of pipe or tube over stud and tighten a old rocker nut with a washer
Could t get a pair of Vortecs?
Ok good video and what does the stock L31 vortec heads stack up against the Dart Iron Eagle,,, vortec heads are cheap new,, can we see a comparison. Dart heads are a hot rod head designed to make power,, the stock chevy vortec heads were simply a production thing that hot rodders picked up on,, I have an old 400 +060 with vortecs curiouse to see
6:16....What the hell are Moly pistons?? I want a set too!!!
Mahle
All that work and money. Why did you not (at least) port match the intake runners on the 882's? They looked horrible.
A more true comparison would be Dart head against a Vortec 062 with the fast burn chamber because the Dart head has the fast burn chamber and that makes the head really flow well. They try to sell Dart heads by throwing off on stock heads but they don't tell you that a Vortec head can make as much as 480 hp and costs around $350.00 per pair used and in good shape.
more people runnin 882s than vortecs on carbed hotrods...that is changing though
I have a pair of these Dart heads sitting on top of a .030-over 350. They do pretty well for the $900 I paid for them.
But for $1200+, I'd go for Trick Flow or even Dart's aluminum heads.
Agreed
Just come out and say I am a salesman for Dart.
Out of the box heads are never really right though. U have to lap the valves in the least. Sometimes valves can be so off that u need to grind seats. Entire angles might be off. Check for yourself.
Why not get some 041/186 heads? They’d probably be a better stock head choice imho
those castings have better intake ports, combustion chamber, and are more suited for the 350 than the 882s.
The narrator says you can't get those heads I seen quite a few heads on eBay for 152 hundred $300 you can get a pair and they may not get the guys but if they do you do what you do because you want to call them have the most horsepower and fuelly heads really do the trick
I have a set of Dart Motown heads ported! What do you think of the Motown heads and how do you think they will do on a L79 sb 327! It's a original bottom end that had a original 20,000 miles!!!!
180cc heads that flowing more then 180cc is that common? i just got set of there 180cc heads but with 2.05 in and 1.60ex 49cc chamber . r they going be same abouts flow rate ?
Thank you for doing all the work so we could learn.. !
Thanks for watching!
How about using aluminum Vortec heads instead of those junkers??
has anyone done comparison dyno tests on the different sized iron eagles on the same shortblock ? ? 180 cc , 200 cc , 215 cc , 230 cc . i'm just wondering how much hp difference there is with the small iron eagle vs the largest one ? or even flow comparison of each ? not factory advertised numbers but real world numbers by non biased head porters
That would be an awesome video.
. Why did they only go 1.94/1.50 valves on the Chevy 882 heads? I thought they had the same valve separation distance as the stock big 'Fuely' valve 2.02/1.60 heads? Looks to have started with small valve/small port 'truck' -882 heads instead of 'car' -882 heads which already come with the valves sizes they enlarged to and have bigger ports and as stock outflow these reworked heads... Also, compression ratio not the same with -882 69cc vs Iron Eagle 64cc chambers... Instead of expensive, dangerous (chance of cracking/leaking) milling of -882 heads, I'd simply use domed pistons for higher compression ratio...Finally, I'd expect 500 HP if using a huge for the street 248/252 cam... That cam is way too big for -882 heads and even too big for the 180cc Iron Eagle heads...
I agree that they chose the wrong heads to compete with, they should have used the 041x,492 ,186,291 just like what the other guy texted that this is a dart advertisement to sell their head if you really search you can find the castings I posted check out Craigslist,yard sales, machines shops,and just asking and looking around but if you have the money for an after market head then bye it.its also all about what do you want to do with your motor and what kind of power your looking for
i just give a set of 194 camel hump heads away for free but i just got 2 454 strokers one with only 6000 miles on it the other one has 38000 on it both with the heavy duty 400 turbo that is the cheap stuff i got for free so far this year i just love the 4x4 short box pu 79 chevy with under 36,000 miles on it factory paint is still in mint condition
do you think doing this test with a set of 906 or 062 vortec heads would have made a difference, those are supposed to be the best factory production head Chevy made. ..or would it not make a difference because you sent those 882s threw every step possible ..I just wonder how the vortec heads would line up vs these 2 sets after its been threw all these steps
Well we don't wanna make anyone mad now
It is always interesting to see, that torque scales LINEARLY with the flow cfm of the cylinder head (regarding same intake runner size in cc, which is important, because otherwise you once again play around with the rev band, like with camshafts, too).
So comparing modern heads, which can flow up to 250 cfm, porting them slightly, which can obtain up to 280~300 cfm if you know what you do, you will just gain DOUBLE the power comparing to a stock 70s chevy iron head, which does about 150cfm.
You can gain easily 300 horsepower instead of 170, with a stock cam. With a smooth idle, with a good gas mileage, with just pulling the heads and replacing them, which can easily be done in-car without a full engine overhaul. (Just remind: You might f*** your bearings and piston rings then ..... hahaha)
Ditto on the vortec! 882 are boat anchors
air flow research heads are the only way to flow, as long as you port mach them with the intake you can make a lot of power.
true
Compare those Dart Iron Eagles to a set of Summit Racing Vortecs @ only $317 each. Think I would go with the Vortecs.
double hump heads 2.02 valves have more flow & give more compression ? witch = more HORSEPOWER
fanghicheck I'm with ya bud, give me a set of 2.02 camel humps, with gasket match and light debuting polish best bang for your buck on old school small blocks, GM engineers back in the day were pretty much on the ball ,not saying there isn't a better head just saying the old school factory camel humps work great for what they were designed to do.
I'd love to see your fuelie heads put on that motor and see how much horsepower they make in comparison to the darts
I wish you guys could have gotten ahold of some double hump heads for comparison..i do agree they are hard to come by especially in stock form...I am an electrician in Virginia and I recently acquired a set of stock, un molested, 461 casting double hump heads.. I got them in trade for doing some electrical work for a fella...they came off a vette and I believe he said they were rated at 375 hp? not sure myself but are they worth getting worked over? if so I would like to use them on a 4 bolt main 350 I have that I plan on installing in my 1973 AMC gremlin... your thoughts would be appreciated!!
If you have a set of untouched double hump heads, you might want to consider selling those bad boys. Street stock oval track racers are always looking for double humps because those are the best when the rulebook says something like "stock only, no Vortec." If you are building a street motor you can probably get enough out of them for a new set of cheap aftermarket heads that are going to be ready right out of the box and give you comperable or better power.
The Horsepower Monster sadly WISSOTA has put the cobbosh on camel hump heads recently, guess I am not sure IMCA wise. sad times we are in.
. 461's are among the best stock heads and if the 461X's with even bigger stock ports, can be ported out to 500+ HP...
+The Horsepower Monster "aftermarket heads that are going to be ready right out of the box" Are you kidding me? Are you telling me that ppl should mount these heads right out of the box? PLZ take youre new heads to the workshop at let them take a look at them before you do anything and always be ready to spend more money on valve jobbs and bowl bleending. I remember my new Edelbrook RPM heads, they looked like shit when i got em!!
I always heard it pronounced “two-oh-two” not “two inches twenty thousandths”
Yeah, that's how I'd normally say it, too. Just trying to be clear for the video.
coccect but he is being clear to the audience
Wait wait wait the biggest valve you can fit in an 882 head is a 1.94 intake? Because Im pretty sure I have a set that has 2.02 intake and 1.60 exhaust and when I bought the heads they had 1.94 int and 1.50 exhaust
your heads more than likely flow more than 193 cfm with the 2.02s
ryan ishee the L82 and the z28 I think in 1973 to the early 1980ies had the big valve 882 heads .I have a 1976 L82 vette which I purchased in 1980 and still have when I rebuilt and moded in 88 it had 882 with 2.02 and 1.60 I have the heads on the car today along with a street supercharger it makes great power hp and torque with other mods
How much are a pair of Dart Eagle BB Open Chamber, Rectangular Heads? Also the price of BB Closed chambered Heads, " Both with 219/188 Valves?