Changed the blades on our Timecutter 54", model 75757. Belt stuck under the Idler Pulley and wife smelt rubber. Pulled deck back out, loosened bolt on idler puller and released belt. Replaced everything back properly this time. When turning on the blades we just hear a click and no blades will turn at all. Thanks for any knowledge share as to what to check; stuck in from North Carolina..
Hey Jim My toro 42” my ride time cutter doesn’t have the nuts for adjustment bought brand new in 2021 model 75745. Is it possible they forgot to put it then on
My stepdad has an older 74327 mower, I can't find anywhere one it which nuts might correspond with the ones you're showing. Right side doesn't go forward at all!
I got a toro MX 5060 that works fine but for abt a hr or less, then the left pump just gets weak, to the point the i can not turn, i turn it off, leave it till it cools off and then its back on again, any ideas on what could be wrong ?
When I push both handles as far as I can forward it goes in a leftward circle. The right handle pushes the mower a lot faster than the left so ultimately to go straight it goes slower than in a circle. How would you correct that? And is there any way to make the mower go faster? Thanks.
Just received a 75750. I found that if going in reverse and trying to turn the front to the right the right wheel doesn't move very much (although when going straight in reverse it seems fine). If I reverse and turn to the front to the left there's no problem. Put the controls in neutral, pull back on the right one and nothing much happens. Pull back on the left one and the left wheel goes into reverse. A Toro dealer couldn't help me.
Same with mine. It’s a 2023 42 in time cutter. I’ve only had it for two days and those handles being off and not tracking straight are really annoying me.
@@KeystoneTexanthere's an additional bolt or set screw in front of the handles that will limit how far the handle will travel this will make the handles uneven. You can fix this by loosening the screws.
@@Joe-wb9fj I did turn the screws. Plus, I had to adjust both of the transmissions to get them in sync with one another. Took some patience but I got it.
@@KeystoneTexanI just had one of these delivered two days ago and mine was so off that one wheel wouldn't reverse. I played with the front adjustment screws for an hour and didn't have any luck but adjusting the bolts on the rear did the trick. I'm disappointed that it came so messed up from the factory but I'm glad that it's tracking straight as an arrow now.
My 34 inch mower while parked, tends to roll backwards? Is this part of it or somewhere to adjust the brake? Will brakes after couple inches rolling back at least 5-6 inch.
Thanks for your videos. One question please. Just got my 2020 50" Timecutter back from the Toro Dealer and now when I come to a stop and go into neutral to fold out the handle bars it goes into reverse before I can put it in park. Where would I adjust that? Thanks for your information. So basically before I can park it wants to reverse.
I have a toro ss5000 and it does NOT have those half moon adjusters. I can see where they would be, but nada. NO scratched paint, was never there. Now what?
Changed the blades on our Timecutter 54", model 75757. Belt stuck under the Idler Pulley and wife smelt rubber. Pulled deck back out, loosened bolt on idler puller and released belt. Replaced everything back properly this time. When turning on the blades we just hear a click and no blades will turn at all. Thanks for any knowledge share as to what to check; stuck in from North Carolina..
What should be the ideal tire pressure for my front & rear tires on my 50" deck zero turn toro 24.5hp?
I've got a 2025 timecutter max 54...levers are slightly off but mine doesn't have that adjustment???
Doing the adjustment tomorrow. Info exactly what I needed
My Man….Excellent tracking adjustment presentation!!!! Got it ! Thank you…nicely detailed 😊
What should the tire pressure be set to for the rear and front?
We do 20 psi.
Hey Jim
My toro 42” my ride time cutter doesn’t have the nuts for adjustment bought brand new in 2021 model 75745. Is it possible they forgot to put it then on
Everyone Timecutter we’ve had has them, we landed toro a year ago and possibly a few models are different but even older models should adjust this way
My stepdad has an older 74327 mower, I can't find anywhere one it which nuts might correspond with the ones you're showing. Right side doesn't go forward at all!
I got a toro MX 5060 that works fine but for abt a hr or less, then the left pump just gets weak, to the point the i can not turn, i turn it off, leave it till it cools off and then its back on again, any ideas on what could be wrong ?
It sounds like the pump is failing. It probably needs a new pump
@@howeequipment is it expensive to replace .? Or rebuild.? Do you have any idea on the price to get it done ? Thank for all the info in advance
It’s an expensive repair. Replacing it would be best. Potentially around $1000 plus or minus
When I push both handles as far as I can forward it goes in a leftward circle. The right handle pushes the mower a lot faster than the left so ultimately to go straight it goes slower than in a circle. How would you correct that? And is there any way to make the mower go faster? Thanks.
Thanks for this! My manual only shows that last adjustment for tracking
Awesome, glad this helped. Thanks for watching.
@@howeequipment turns out mine doesn't have any adjustment nuts in the rear 🤷 2022 model# 75750
@@jstinnette yours should have the same nuts to adjust.
Just received a 75750. I found that if going in reverse and trying to turn the front to the right the right wheel doesn't move very much (although when going straight in reverse it seems fine). If I reverse and turn to the front to the left there's no problem. Put the controls in neutral, pull back on the right one and nothing much happens. Pull back on the left one and the left wheel goes into reverse. A Toro dealer couldn't help me.
I have the same problem. In reverse on has more power than the other. Maybe once make adjustments to track straight forward it will fix reverse
How to slow down my time cutter hard ground I have to slow down the problem is can't hold a straight line's holding the handles down half way
The right handle on my time cutter does not respond. Is this what I need to adjust?
@@danielmarjanovic9957 I would check the pin to bipass the transmission on the back of the mower
I just had my 42” Timecutter delivered two weeks ago. I have the third issue you called out on your 42” where the handles aren’t even.
Same with mine. It’s a 2023 42 in time cutter. I’ve only had it for two days and those handles being off and not tracking straight are really annoying me.
@@KeystoneTexanthere's an additional bolt or set screw in front of the handles that will limit how far the handle will travel this will make the handles uneven. You can fix this by loosening the screws.
@@Joe-wb9fj I did turn the screws. Plus, I had to adjust both of the transmissions to get them in sync with one another. Took some patience but I got it.
@@KeystoneTexanI just had one of these delivered two days ago and mine was so off that one wheel wouldn't reverse. I played with the front adjustment screws for an hour and didn't have any luck but adjusting the bolts on the rear did the trick. I'm disappointed that it came so messed up from the factory but I'm glad that it's tracking straight as an arrow now.
What about when the right arm is stiff
I have a 2020 75742 time cutter and I don’t have an adjustable nuts and that half moon thing doesn’t work
My 34 inch mower while parked, tends to roll backwards? Is this part of it or somewhere to adjust the brake? Will brakes after couple inches rolling back at least 5-6 inch.
Both of the nuts in there rear need to be adjust to sped up on both sides.
Thanks for your videos. One question please. Just got my 2020 50" Timecutter back from the Toro Dealer and now when I come to a stop and go into neutral to fold out the handle bars it goes into reverse before I can put it in park. Where would I adjust that? Thanks for your information. So basically before I can park it wants to reverse.
Both of the nuts in the back by the wheels needs to be “sped up” each one needs to be turned to the left until it doesn’t creep back.
@@howeequipment thank you so much extremely appreciated 👍
Worked great! Thanks Buddy!
How about a 2007 z5000. Pulls to right. Doesnt have that style.
it’s probably not recommended, but how do you adjust the governor on a toro time cutter?
Loosen both of the nuts on the wheel motors it looks like but don’t take my word for it.
Why would anyone want to slow down? How do I make mine go faster!
Does the same adjustments go or a toro titan?
It depends on the year. Some titans have this adjustment
@@howeequipment I have a 22 with the my ride. Does that make a difference?
@@traviswarehime5796 that should be the same as far as the nut in the back
I have a toro ss5000 and it does NOT have those half moon adjusters. I can see where they would be, but nada. NO scratched paint, was never there. Now what?
Ever figure it out ? I have an 07 same thing. Pulls to right. Cant find out how to adjust it.
Thank you for the wonderful break down
Does this work on the 2022 titans too?
Yes
Please show tracking on a SW5000
Thanks for posting this.
thanks, great video