How to Adjust a PTO Clutch
HTML-код
- Опубликовано: 15 окт 2024
- Step by Step!
In today's video, I'll be showing you how to Adjust or "Shim" an Electric PTO Clutch.
The process is quite simple, but you'll need these tools to complete this task;
A 1/2" Wrench or Socket & a set of "Feeler Gauges" (To measure the Armature Air Gap in Clutch).
Follow these simple steps & you'll be back to cutting grass in no time!
_______________________________________________
If you enjoyed the video, hit LIKE & SUBSCRIBE!
New videos every week!
DONATE:
Bitcoin: 1NYgPvcvBWuhGRewsLE4Scy1cbzwndh5hZ
SOCIAL MEDIA:
/ eliminatorperformance
/ eliminatorperf
/ eliminatorperformance
2ND CHANNEL:
EP Vlogs: / @eliminatorperformance...
GEAR:
Camera: amzn.to/2HVkW9o
Tripod: amzn.to/2HGWt4w
Microphone: amzn.to/2J7k9DA
Cheap Mic: amzn.to/2xCBn6z
Headphones: amzn.to/2JeHUG9
Editing Software: amzn.to/2JD7OTx
Photoshop: amzn.to/2HBY6Ez
MUSIC:
Intro/Outro Music: Burnt - Jingle Punks
Even after 4yrs, your video is still being helpful! As many said - great teacher, straight to the point, THANK YOU for passing along your knowledge!
I’ve just recently obtained a 1997 JohnDeere GT275 with the 17 Hp Kawasaki motor and your videos
on that motor have been great! Thanks a million and appreciate ya man!
Thanks for sharing your knowledge. My clutch on my Gravely 460 has been shutting off after 10-15 minutes of mowing for the last few months. It finally quit all together a few days ago. Between this video and the one on testing a clutch and a few other YTubers I was able to determine that the air gap was over .025" I tightened it up to .020" and it works like new! Saved me over $500. Thanks again
This is what’s happening to me …
Im currently replacing a Collapsed Bearing in an Electric Clutch on my own Husqvarna Lawntractor, i stumbled across this video, I didnt know that adjusting the clutch clearances was even a thing, "Thankyou for the great Video" straight to the point with clear instructions 👌👍
I will now adjust mine as per your Guide. Much appreciated for the upload. CHEERS 🍻 🙏
Thanks much, I'm retired and cant spend a lot on my Equipment so try to di it myself. Your videos are great and really helpful. Thanx again
This is how you do a video....Very professional and informative. TY👍
Not a wasted word. Totally useful.
Thanks for watching!
Thank you for a clear, understandable, and concise lesson. I also appreciate your non-use of foul language.
Thanks for watching Thomas!
I just got true with a clutch job. My bearings were bad.
I got to check the air gap and tork the bolt holding the clutch. Great video man.
Thanks for watching!
Great that you supplied us with the specs for other PTO clutches, nice simply repair and well explained. Appears this PTO had a lot of hours on it without being serviced.
Dude, thank you so much. My wife and I were gifted a Honda lawn tractor from her family. It's an older tractor but in great shape, but one problem I've encountered is that it's hard to find info about fixing it or maintaining it. I have a shop guide that described shimming these things when servicing them, and mine clearly needs service because I could see a fairly substantial gap when operating the lever with the engine off, and no doubt the clutch wasn't making enough contact to send drive power to the belt. But not being much of an expert when it comes to automotive or machinery repairs, reading the service manual's instructions made the process sound so much more complicated to me.
Now, thanks to this simple explanation of the how and why of the process, I will have no trouble at all applying these instructions to my Honda's PTO clutch, using the shim gap specs from the service manual to get it just right.
To me, this is one of those great videos that really, really made my life better. You rock!
Thanks for the kind words, good luck!
Very good video. You have saved all of us from paying a lot of money for something that just needed adjusted. Thank you for your expertise and time!
Thanks for watching!
You saved me 300$!!! I had just ordered a new clutch on Amazon for my Gravely Proturn, not even knowing these clutches were adjustable. I made one rotation on each adjustment bolt and BAM back in business. Thanks again!!!
This is one of the best how to video I have seen....the speaker gets to the point and is not always going uhhhhhh...well done and clearly explained and illustrated...thank you
Thanks for watching!
Outstanding video my friend. I came to YT looking to see if there was an adjustment for the PTO on my 20 yr old Simplicity, and I hit the motherload of information with this video. Very well done video!
Thanks for watching Dukerdr!
Same here with my 18 year yth2148, sometimes it wouldn’t engage when it was hot, thanks for the information
@Jackie Liner I have the same motor I just got what spec did you adjust yours too on that clutch?
Well done! Very informative. You know your stuff. You give just the right amount of information without talking too much. I wish more videos were like this one.
Thanks for watching Paul!
Great information, never knew they were adjustable. Thanks for sharing
Some are, some aren't. The ones that are adjustable are nice because as long as you keep them within spec, they tend to last longer!
Thank you for getting straight to the repair and information plus your advice. Time is important to everyone. Thank You 🙏
Thank you for a very informative and straight to the point video.
Great video, straight forward, no BS, good technical info.
Dude, THANK YOU ! Finally a clear, concise "how to" video without all the extraneous BS some people include. Well Done @
Thanks, all my videos follow the same principle.
Checked out your video and decided to try this. Worked out great! I have a 2010 Husqvarna RZ2454 with the 24hp kohler engine. With an OGURA pto. Took it off and adjusted the pto with a fueler gauge to .015 and worked out awesome. Beats buying a new one. We have a mower dealer here in Minnesota selling a pto for $225. Found one on Amazon for $130 took it off and tested the ohms which read 3.5 ohms so it was still good. Now I'm sitting pretty with ah fresh cut smell of grass in the PM lol. Thanks for the vid you saved me some dollars my friend. Take care and have a great day.
Awesome, glad it helped, cheers!
I adjusted my Cub Cadet's PTO several years ago. I found your video to be spot-on.
Thanks for watching!
Keep uploading.
Your video really helped me thanks a lot didn't have money to take it to shop
That's a great explanation, I tell you that is just exactly like tuning up a drum.
Nice job man quick and to the point no mistaken how to get the job done thank you much for the information and knowledge.
Great job on everything in the video 👍👍👍
Appreciate the info man, I have a 2007 Cub Cadet M60kw tank with a 25hp kawi, Been looking everywhere to see if it's a warner or ogura?
THANK MORE INFO, THAT'S ALL I NEED.
Great video I had no idea about that adjustment! What is your opinion about what rpm to engage the PTO? I have always engaged at full throttle, but I have seen debate about that lately and some people saying I can wear out the PTO faster, engaging at full throttle. What are your thoughts?
@@prostreetgsxr half throttle is recommended, 3/4 throttle should be ok. I wouldn't recommend full throttle engagement as it's harder on the entire system (clutch, electrical, belt, engine).
Great video! The details much appreciated
AWESOME THANKS BRO NOW TO ADJUST IT TO THE UNDER 25H.P SPECS.
I'm sure there are a lot of teachers who can not explain as well as you. I speak french and understand very well your explanations even if you do not breathe hahahahahahahaha! Thanks, have a good weekhend
I edit out all the breathing! Makes for a quicker video haha thanks for watching!
Great video. Thank you!
great job
GRT VIDEO....NO BS INVOLVED.....I have to do this to mine and didn't know about the different types and gauges, thx again
Anytime, thanks for watching!
The best video, you don’t waste any time and straight to the point, Thankyou
Thanks for watching!
Excellent video and information.
Thanks for watching!
Excellent video. I have a question. My machine is a Cub Cadet. You say it shouldn't make a sound when turning the pulley. But I set it to 0.025 but it makes a sound when turning. Thank you
Ideally it shouldn't make a sound, but remember you may have it upside down so gravity pulls it a bit and things can rub. Try it it on the machine usually 0.025" should be good to go!
Great informative video...I was able to adjust mine without removing it...
Great video. Beginning to hear @ slight rattle…don’t know if it’s bearing or it needs to be shimmed.
Fastastic video. Could save 100’s. Tay.
480 hours.
Excellent, thanks.
Thanks for this video. It was really helpful. But, I tightened the same amount on all 3 nuts each time and then checked, until I had the .020 gap in all 3 places. I like doing things the easy, I guess. I just subscribed to your channel.
Thanks for watching!
this is a great video , nobody has done this adjustment . Nice to know .
Thanks Chris, as stated, the adjustment has most likely never been done on this clutch. Now that it has though, the rattling has gone away!
(Video series is finished, and I'll be posting videos as time goes on).
Specs start at 2:09. Thanks for the video!!
Thanks for watching!
Excellent video!
Thanks for watching!
I usually adjust mine to .012, or on worn PTO'S I adjust to .008. As long as it doesn't drag its fine.
Thank you for the info man. Awesome video. Thank you!
Thanks for the very concise and informative video!
Big help thanks
Awesome Video and Explanation!!☺🥰☺
Great video! Very helpful info presented in a professional and easy to follow way!
Great information never knew this. Thanks for sharing your superior knowledge & gift.
Thanks Chuck
Thanks for the kind words Chuck!
I am having a issue with my pro on my exmark. Il pull it it won't catch. After a few tries it will catch. My mechanic said there was no way to adjust it rather get a bew one. Interesting I wish I new more thanks for this video
@@garyhadden5681 if they don't have the 3 nuts then they are non adjustable. I would start by testing your battery 1st, not just to make sure it's 12.6+ volts, but also that it has good amperage under load. And also check your charging system (13-15v while the engine is running at full rpm). Your electric PTO relies on a strong electric system. I've had mowers come in and customers want new PTO clutches installed for $500 and all they needed was a new battery. Good luck!
@@EliminatorPerformance ok thanks I actually put my battery on a tender on Friday pull it off Saturday it could be that il switch out batteries I bought one but been putting this one on the tender. Thanks buddy i meet pto not pro you figured that anyway thanks
very informative, good video
Straight forward, very helpful video, thanks !
Thanks Andrew!
Great video, right to the point. Thank you.
If it is still making noise when spinning but you're well above the gap range do you make it looser still or tighten it down to specks and just let it rub?
Just like a spark plug gap , it makes sense to have the gap set at the least gap. This is because as the material wears away , the gap gets larger. So therefore the set gap stays in spec longer if started at the smaller end of the scale.
Very good! Clear explanation and to the point! Thank you.
Thanks for watching!
Well this solve my mower blades to have power again threw tall weeds ? I had a bad oil leak and only one bolt in my sears o turn 20 hp mower . Made a crack in oil filter and oil all over the clutch . I but 3 new bolts back to hold engine back right .(power wash clutch) I could of bought it used that way ! I put a new mower belt on to . The mower blades stops in very little grass . A few weeks ago it could mow 8 inch weeds with ease . All so times back my mower belt was burning some threw to tall of weeds ..thank you - please reply . I not paying over 140 for a new clutch and spent hours trying to find one for that price . Good video
My deere f935 is slipping and shutting of after a bit of work under load, hope this will save me a replacement, these go for 900usd +300shipping and tax 😬
Nice work bro. Thanks
I have question, if the PTO is off spect. Will it cause the blades to stop running when it start cutting grass.
Outstanding!!! Thank you!!!
Thanks for the great video. I have two old troy bilt gtx 16 and 18. The 16 has a warner, the 18 ogura. I recently worked on both engines and adjusted the pto to specs. That was before I watched your vid but the specs I had were the same. On both of them when I got it to the correct air gap, I noticed that the pulleys were rubbing on the housing. I rechecked the gap and it was spot on. I was concerned about it because before I adjusted it, it spun free without resistance. I bought this up on a tractor forum that I belong to and those who replied said it was normal for it to rub the housing when disengaged. A couple people said that acts as a brake to stop the implements. Does this sound right to you? In any event both ptos work great right now. Also, before the adjustment they were way off as shown in your vid. Thanks again.
It depends, rubbing can indicate that the pto plate is warped from heat or use over time, also could mean it's out of adjustment. They have their own brake yes, and when disengaged it will contact the pad. What I'm referring too is, if you're making the adjustment, and set the clutch to the proper gap, and notice it's quite hard to spin because something is binding up, then you might want to go with a bit more gap. They can warp over time and when you disengage a warped clutch that's set too tight it could cause significant damage.
Great, informative video! Very well made.
Well done. Can I make this adjustment on my 214, W/O removing the clutch? Is there clearance? Thanks.
Hard to say, some have room, others don't have enough room. Honestly, best to remove it, and use some nickel antiseize on the shaft so future removal is easy! Dielectric grease in the plug connector and you're good for years to come.
Thanks great information needed it before my anger got the best of me
Thanks for watching, best of luck!
I get how to adjust the PTO clutch but not why. Can you give me examples of what happens if it’s too loose or too tight? My mower is moving forward in its own & near impossible to switch gears due to the tension on the belts. Would a clutch out of spec do that? I replaced the clutch pulley & drive belts at the end of the last season so I’m not sure where to start.
Good day I don't have pto clutch , but you do good videos. Thanks
Thanks Don!
Do you have to take the pto clutch off the mower to perform this service?
Not sure where the specs are from, but I adjusted the Ogura clutch on my Husqvarna with 26 hp to the 0.019 recommended in video. It was too close, and engaging clutch would kill the engine. I had to back off bolts and increase gap until the mower would operate normally. I need to check the gap to see what it is now, but the 0.019 was too close.
I just purchased a new to me Bolens 5019h harden tractor with a 2 stage blower. Owner stated he recently replaced the clutch and it looks brand new. Issue is when I shut off the blower it will coast for a good minute before it finally stops. It sometimes sound like I never turned it off but it does eventually stop. I am guessing my gap is too tight? Manual online states .015 is gap and my clutch has 4 bolts. I see two windows to check gap and it looks tight. Is this bad for the clutch or just unsafe? Do you think he assembled it wrong?
what is a good way (brake cleaner?) to spray to pre-clean the airgap to assure accuracy in measurements?
Great video! I definitely learned something useful.
Thanks for watching!
Thankj you excellent video,
Would a failed PTO clutch kill a battery? Mine has been acting up and not reengaging after a cut, got a new battery and now it’s dead. Thing the clutch is shot
the main magnet on mine is loose/ has play in it. So adjusting it has a problem. is that normal or is the PTO warn out and ready to be thrown out?
Great video! 👍🏼
Thanks for watching!
Thanks dude great video
Thanks for watching!
Never worked with one of these clutches before until today and I had my john deere 240 clutch fall apart, 2 of the 3 nuts loosened and fell off and just happened to have a clutch on my old mower with the same springs and nuts. Put them on my clutch but didn't know about adjusting it so I just tightened it till it was tight then loosened it till it spun it with no noise. Went out and noticed it seemed to be slipping and bogging down the engine. Should I just adjust it with feeler guages or just throw a new clutch on?
My clutch spins freely when engaged, tearing out the wires. It's an early 2000's Simplicity Regent. Is there a stop for the clutch to prevent this motion?
Yes, supposed to be a metal bar that drops down. Get your model number and Google that number with the words parts diagram after it and check what parts you're missing
Simplicity has no record of my unit's model number. Canadian, eh? Maybe I should try again. Thanks for the advice.@@EliminatorPerformance
Thank you
Thanks.
heck of a great job! thanks to you for the video!!!
Thanks for watching!
Good video...I have a Dixie chopper with clutch problem it engages for little bit then it quits..does this singtom has to do with the clutch gap? Any suggestions will be appreciated.
Not too sure, might be clutch pads worn out
Good job with this video, thank you. My Cub Cadet PTO is going off & on. I changed the switch itself but that did not help. Could a clutch that needs adjustment as in this video cause the PTO to constantly cut off/ quit turning?
It's quite possible that the armature air gap is so far away from the magnet that it has an issue. It's an easy fix so it'd start there, you can test for resistance while you are working on it
It's quite possible that the armature air gap is so far away from the magnet that it has an issue. It's an easy fix so it'd start there, you can test for resistance while you are working on it
@@EliminatorPerformance thank you, will do
My mower just quits cutting after 20 minutes. Fluids full . I’ve ordered a new switch . Any other help does it sound like clutch issues ??? My mower huskavana 60 inch professional 5 years old
Wonder what you are supposed to do if you have a Ogura clutch on a 25 hp?
,would this be the reason why once my blades stop from reversing, they do not want to start up again..or after running for about 20 mins?
Thank you, you are great!
Thanks for watching!
I was cutting the grass on my John Deere la145 and the blades suddenly stopped. I can hear the pto trying to engage and i can even see the belt slowly turning the blades. Do you think it's an adjustment or a bad pto altogether? I appreciate the help
I have a 2008 simplicity broadmoor 20 hp. The problem I am having is that when I get into thick grass the blades are slowing down. the motor rpm is not changing and the belts are not slipping. I beleive the problem is that the clutch seems to be slipping under load. How can I fix this
I have a 2012 toro timecutter 3200 when I pull the PTO switch it just squeals sometimes and don't work or it squeals for a bit then kicks on. Does it need ajustment or replaced.
Try an adjustment if you can, the brake may be engaging because the plate is too far away. If you see the springs, you'll know you can adjust it
I have a new Pto clutch and when I installed it per the instructions for the xtreme pto clutch the motor has resistance and does not want to turn over. could the adjustment be off fro. the factory? And on a 265 is it supposed to have a spacer in between the drive pulley and the pto? my old pto fell off and broke. I didn't see a spacer on the ground but maybe that's my problem.
There's usually a spacer in between the engine and the PTO clutch, and extreme sometimes also use a washer that is needed. I called them because I had doubts (it didn't seem like much surface area) but they assured me that's how it was designed to be run. Absolutely no issues on the one I installed here: ruclips.net/video/lb_deDPQYt0/видео.html
Genius
Great stuff,, just what I needed
Thanks for watching!
CANT I adjust while on the mower? Scag Freedom Z