I really liked the tool you made yourself to adjust Cam timing but i really wanted to see how you used it to adjust the cams - its hard to do the work and film at the same time :) I enjoyed your video very much.
Thank for this video. I have a lot of issue with this engine, after a strange noise within the engine then after that the car didn't start again. I wish to change that engine for a more simple one, maybe a petrol engine. Can you help me for advices on that matter? Which petrol engine can i replace it with? Thank you in advance...
Replacing diesel engine to a petrol engine lot of things to be replaced and would be costly. Instead of replacing engine buy a used car and exchange this xtrail, that would be economical to you. If repaced engine dosen't work properly, that will be headache later on.
Hello sir, very informative video.My vehicle (X Trail T31) is also having multiple problems and is in the local garage for the last 5 months.After half engine change ,the car started fine but no accleration beyond 2000 rpm, tried every thing ,but no improvement.Finally, thay sent ECM for testing and repair.But after repair of ECM, the car doesnot start at all.So, kindly help me to diagnose the problem.Thanks.
No RPM above 2000 is not ECM problem, there are many parameters of sensors, braking system, cruise control, abs module and dpf all these are responsible for reduced sped. Now they have bricked your ecm
Appreciate your skill and also your tools.how come one cyilnder was o pressure compression.what was the cause . You need lot of patience to repair the engine out side mis assembly .your home made tool was very helpful to correct the timing any way cheers good work Irmao 🙏💐
What a nice video. Mine still has a mileage of 60K+ and its a T31 automatic M9R 6speed DCi. Soon I need to change the transmission oil. Can you show me how or anyone show me how?
@@devautoelectronics thanks for the prompt replky yes I will do that however my unit has no transmission dipstick and I can’t find the opening where to drain the oil.
@devautoelectronics Hi thanks for your reply, not sure how to explain this but i will give it a go. I get to the point were you need to add the numbers and letters for the injector but some of my letters are grey making impossible the coding. I got a picture but i'm not sure how to show it to you. Also what do you mean when you say " then only injectors can be coded? Thank you
hello. can you tell me in which part of the engine is injector 1. on the flywheel or on the distribution. and what codes must be written in the ecu. thank you
@@devautoelectronics I didn't manage to code the injectors, I tried with OTOfix d1 pro but without success, the procedure is completed and after the codes are not written in the ecu.I don't know what else to try
my car starts but does not accelerate more than 1500 RPM and when checking with the Delphi interface the injector codes show AAAAAAA and error P0611 with which diagnosis can I write them back?🙏🙏🙏🙏🙏
Hello Sir, I have the same SUV and getting 1 Error code "P1435 - powertrain", any idea what this error code mean. Also I see some kind of smoke coming from engine oil dipstick, is this common on M9R Engine. Any help please, thank you in advance.
This code is usually for DPF, if regeneration cant help then check and change dpf pressure sensor, still not done then remove DPF and wsah, clean manually and then try deleting this dtc several times it worked for me
Aap pahla cam ko lock kariye 10 mm bolt se baad mein fuel pump se cam tak 18 data ana chahiye aur crank mark barabar rakho yehi perfect timing hai ...baad mein kahi chakkar lene ke baad mark pe aa jayegi ..... he video dekho ruclips.net/video/1EwGvCxey1I/видео.html
Very very good & smart work, Problem finding is very hard & tiredness work 👍👍🙏💐💐
Thank you
I really liked the tool you made yourself to adjust Cam timing but i really wanted to see how you used it to adjust the cams - its hard to do the work and film at the same time :) I enjoyed your video very much.
Thanks for watching bro. One man job so difficult to film, I just inserted the tool in two holes and turned its got adjusted😀
Bravo pour voter travail.
Thank for this video.
I have a lot of issue with this engine, after a strange noise within the engine then after that the car didn't start again.
I wish to change that engine for a more simple one, maybe a petrol engine.
Can you help me for advices on that matter?
Which petrol engine can i replace it with?
Thank you in advance...
Replacing diesel engine to a petrol engine lot of things to be replaced and would be costly. Instead of replacing engine buy a used car and exchange this xtrail, that would be economical to you. If repaced engine dosen't work properly, that will be headache later on.
@@devautoelectronics thank you very much for you advise
Hello sir, very informative video.My vehicle (X Trail T31) is also having multiple problems and is in the local garage for the last 5 months.After half engine change ,the car started fine but no accleration beyond 2000 rpm, tried every thing ,but no improvement.Finally, thay sent ECM
for testing and repair.But after repair of ECM, the car doesnot start at all.So, kindly help me to diagnose the problem.Thanks.
No RPM above 2000 is not ECM problem, there are many parameters of sensors, braking system, cruise control, abs module and dpf all these are responsible for reduced sped. Now they have bricked your ecm
@@devautoelectronics Thanks for reply,,, but kindly suggest how to find the fault in my X trail ? mY mechanic has tried everything.Pl.help.
Appreciate your skill and also your tools.how come one cyilnder was o pressure compression.what was the cause . You need lot of patience to repair the engine out side mis assembly .your home made tool was very helpful to correct the timing any way cheers good work Irmao 🙏💐
Thank you so much Franco.
That cylinder valve was opening early due to mistiming. This engine is little complicated about timing.
What a nice video. Mine still has a mileage of 60K+ and its a T31 automatic M9R 6speed DCi. Soon I need to change the transmission oil. Can you show me how or anyone show me how?
Use company recommended oil grade and oil code. Do not use any other oil
@@devautoelectronics thanks for the prompt replky yes I will do that however my unit has no transmission dipstick and I can’t find the opening where to drain the oil.
Its not DIY work go to professional they will do it properly with procedure
does this m9r engine has a power steering fluid container
No, it has electric power steering
Can you tell me please how did you dode the injectors? I got the same Xtool and it doesn't let me to code them. Thank you
For injector coding, go to special functions and select your region, my region is "far east" then only injector can be coded. Directly not possible.
@devautoelectronics Hi thanks for your reply, not sure how to explain this but i will give it a go. I get to the point were you need to add the numbers and letters for the injector but some of my letters are grey making impossible the coding. I got a picture but i'm not sure how to show it to you. Also what do you mean when you say " then only injectors can be coded? Thank you
@devautoelectronics I adde a short video of my issue if you can have a look.Thank you
@@neculaiflorea3468 when the region is correct, letters will automatically highlighted.
@@neculaiflorea3468 yes, put on your channel and share link
bro duster me DF859 injector programing cycle not perform ye code aa rha hai ye solve kaise hoga
1No Bhai.....Good Job...Great
Nic video sir 👍👍👍
hello. can you tell me in which part of the engine is injector 1. on the flywheel or on the distribution. and what codes must be written in the ecu. thank you
Flywheel side is no. 1 injector, write the code exacly on injector
@@devautoelectronics thanks for the answer. with what diagnosis did you write the codes🙏🙏🙏I understood that you cannot write with any diagnosis
@@adrianVasile-vp1bf I have xtool ps 70 pro... Launch, autel can do
@@devautoelectronics I didn't manage to code the injectors, I tried with OTOfix d1 pro but without success, the procedure is completed and after the codes are not written in the ecu.I don't know what else to try
If your colleague have xtool or launch, tell them to do the job
my car starts but does not accelerate more than 1500 RPM and when checking with the Delphi interface the injector codes show AAAAAAA and error P0611 with which diagnosis can I write them back?🙏🙏🙏🙏🙏
First you write the injector codes, its related to injector coding.
Hello Sir, I have the same SUV and getting 1 Error code "P1435 - powertrain", any idea what this error code mean. Also I see some kind of smoke coming from engine oil dipstick, is this common on M9R Engine. Any help please, thank you in advance.
This code is usually for DPF, if regeneration cant help then check and change dpf pressure sensor, still not done then remove DPF and wsah, clean manually and then try deleting this dtc several times it worked for me
@@devautoelectronics Sure Sir, let me try this. Thank you so much.🙏
How to fix p2425 code Nissan xtrail t31
This code is related to egr, check egr components, wiring, sometimes ecu faulty
@@devautoelectronics nai ho paa raha
👍🏻
भाई डस्टर का टाईमिंग कभी कभी मार्क पे आता नाही फिरभी गाडी चालू रहति है। और मार्क पे सेट किया तो गाडी नाही स्टार्ट होती। ऐसे मेरे साथ 2 बार हुआ है...
Aap pahla cam ko lock kariye 10 mm bolt se baad mein fuel pump se cam
tak 18 data ana chahiye aur crank mark barabar rakho yehi perfect timing hai ...baad mein kahi chakkar lene ke baad mark pe aa jayegi
..... he video dekho ruclips.net/video/1EwGvCxey1I/видео.html
Kaka tumchi garage khai asa!?
Kukali
Engine renault 💩
Yes