for what it is worth....after reading all of these negative comments.. i was all ready to send this back... (i was trying to connect my blue tooth headphones to my non blue tooth old tv.. ) .. following the instructions didnt seem to make any sense, so finally i just plugged the adaptor into the TV and turned on my headphones... CONNECTED.. volume is fine, no delay,, no problems at all.. works perfectly and no issues
I struggled trying to connect this device to my TV. I tried pairing it when it was connected to the TV. Finally, I removed the transmitter from the TV and paired it separately with my Bluetooth capable headset. Once paired, I then inserted the device into the audio output of the TV and it worked perfectly.
I have an LG 7000 and can’t seem to find an audio output to connect the transmitter to. Is there any other way to connect it so I can hear sound out of my Bluetooth earbuds?
For those having trouble with playback on 2 devices at the same time. Make sure that the device you are transmitting from is not pairing directly to your other two devices. For example, I use this transmitter to hook up my Amazon Alexa to two different external speakers located on separate floors of my house. I was having trouble playing music through both speakers at the same time. Realized that Alexa had (on her own, I think) paired with each speaker separately. Went into the Alexa app, unpaired both devices, followed set up instructions for the transmitter and both are working perfectly and simultaneously with no lag.
I am able to pair 2 bose head sets, however one headset is getting disconnected automatically in 3 min approx .. voice is not clear on 2nd headset either its choppy ... Could you please advice if this can be fixed ? Definitely ni issue with bose headsets as its working fine with single pairing
@@karthik1942I'm not sure if your issue is the same as the one I was having, but make sure that the primary source you are transmitting from is not paired individually with either headset. In other words, make sure that your headsets are paired only to the transmitter.
Nice little unit. Works well for me - 30ft range no walls, 20ft range ground floor with two walls to get through. Upstairs, just through ceiling, around 25ft. Pairs quickly for me with portable speaker or earphones. Approximately one-word lag when used. Out of sync can be easily seen when watching lips move on TV, but that's to be expected due to transmission lag conversion both ends. Listening to music no problem whatsoever, but don't use if you need exact sync receive - you'll be one word or note delayed! Well worth the money to be able to select either TX or RX. Quality product.
Thank You Soo Much for explaining this pairing mode. I was trying to pair with the wonderboom for 3-4 days and couldn’t do it until I saw your video to do it.
I thought mine wasn't working correctly for my projector to my JBL Boombox but I had the device plugged into the AV jack instead of the headphone jack. Now it works. I'm going to check the sound delay time next.
In receiver mode would be able to connect to my console and my phone simultaneously? Because I’m looking for a way to hear my gaming effects and be able to chat on discord at the same time.
Hey can you pleaae help me? i paired with headphone but still sound come from tv and headphn as well. As i connect comcast via hdmi.any solution please
I have recently purchased two TT BA07 through Amazon and was using it perfectly fine for last 2 months while paired with each other..one in TX mode and the other RX mode.. and suddenly one of the TT BA07 set to TX mode stopped transmitting audio...they sync together perfectly but the one of them doesnt have a proper audio coming out...there is either no audio or a sound some kind of a bad connection...i cross checked with multiple other cables and paired with other devices ..the situation is same. Please help. What should i do?
once you set up the TV and blue tooth headphones, does the tv speakers get muted and you hear the sound only on the headphones, or the tv speaker will also work so while you can hear the tv with the headphones and someone else in the room without headphones can also hear the tv?
I've 4.1 bluetooth headphones (sony wh-ch700n) which I want to connect to a bluetooth 5.0 transmitter. Does this give me all the benefits of the 5.0 such as: lower latency and distance? Or do both advices need to have 5.0 to work optimal. I appreciate all the help!
I have a lot of problems connecting. Sometimes it works first try, sometimes it takes me am hour of reseting my headphones and the transmitter multiple times. I don't think it's a good product personally lol
Hi, I wonder if I can connect 1 taotronic in Tx mode to another one in Rx mode? I need to pair 1 analog mixer to my in ear headphones. Is that posible?
does this support bluetooth 4.2 used by my original AirPods pros? I know it supports bluetooth 5.0, but does is it backwards compatible? Thank you in advance.
I've come to find that my beats x headphones volume function gets disabled when paired to this. The volume stays way too low to use. Other Vmoda wireless 2 headphones work flawless. Must return due to this incompatibility
I have a question. I work with a metal detector that does not have a wifi and bluetoth connection, can I with this taotronics device take the signal from the detector out there on the 3.5mm jack to connect it to this Taotronics transmitter and get the sound on my smartphone . thanks in advance for the reply regards for all
I'm using this product with Airpods 2 and MBP 15 and the volume is very low. The battery was fully charged and I tried with the charging cable connected as well. Any thoughts?
To answer everyone's question about pairing two of these units together, one transmit mode and the other in recieving (Tx to Rx).. yes you can. At the time of this posting i just did it two minutes ago and it worked flawlessly with my Samsung Galaxy S8. Secondly, you may be wondering if you can connect this to another model such as the TAO 08 model which is just a reciever with play, volume control, mic to and answer calls.. yes you can pair to this unit as well.. as long as one transmit and the other recieves you should be able to pair..although if one has a mic and the other doesn't you may not be able to use that feature.. i dont have 2 to test but i will soon.
Not based on this review but in part on this review, I purchased this TaoTronics 2 in 1 Bluetooth adapter and found it less responsive than you have. I understand I might not have got a good one but the delay is there and I will be returning this one to Amazon.
I check the TaoTronics mentioned that in some comment: Bluetooth is not an instant transmission protocol and there are some lag / delay due to the time it takes for the signals to be encoded and transmitted. Typically if you're listening to music or audio only, you won't ever notice this lag. However, pair audio with video or use Bluetooth devices with musical instruments where the user expects instant feedback and it is noticeable. Here is the link of the discussion: www.amazon.com/there-delay-between-what-hear/forum/Fx20B5FQTMI4R62/Tx2DF93XXS5QKZF/1/ref=cm_cd_naredir?_encoding=UTF8&asin=B00GKEAQ2M&ref_=ask_dp_lsw_al_hza
Thanks for the feedback Lianziko L. I find it just a little self-serving for a company to suggest that I should simply "get used to the lag" while using it for the purpose I bought it, for my TV. As Bluetooth technology gets better, I suspect this problem will be a thing of the past.
Thanks. we follow the video guide to pair two BT headphones (TX mode) and it work just same as your video guide but ONCE only. When we use it again, it had no response so that we follow the video guide to connect the (same) BT headphones again . Based on the lighting signal, both BT headphones should be connected to TT-BA07 already . However, there only the 1st BT headphone have voice but the 2nd BT headphone is no voice. do you know how to fix this problem ?
When you pair the two bluetooth speakers together are you using a phone, laptop, or tablet. I'm waiting for my Tao to arrive and am going to be trying to connect two bluetooth speakers to either and Iphon or laptop and wondering if one was easier than the other. Thanks
if I have two of these TTBA07 devices, can I use one in RX and the other in TX and pair them? This setup is useful when you have a non-Bluetooth TV and speakers. Thanks in advance!
Works great. One small issue. While in transmit mode, whenever there is a pause in sound, the device mutes and resumes when there is noise again. I assume this is to block out any hiss or ambient noise. Is there a way to shut that off? I find it a bit irritating. I would like to hear the sound unaltered
I am trying to use TX mode to pair from tv to AirPod pros. The issue is it is pairing with random devices and potentially even my neighbors devices. I have successfully paired it once but through trial and error. Is there a way to have it pair with my airpods first?
I am trying to pair this with my 2015 Audi A5 so I can play my iPod. It recognises the device but keeps saying that pairing had failed. What can I do to get it to pair?
I just bought the TT-BA07 in hopes of being able to use one pair of headphones for my PC and my iPhone. My headphones are TaoTronics TTBH-10. I am having a lot of issues with getting the iPhone and the headphones to both be connected at the same time. I know that the TT-BA07 us a multi-point device, so in theory everything should work; however, I am having problems getting them to play together. The situation is perhaps complicated by the fact that I have an Apple Watch, which is also connected to my iPhone. Is there a way of making this work? I find the procedure for pairing mutiple devices confusing, so perhaps I'm just doing it wrong. Any help gratefully received.
is this device can transfer headphone's microphone? I' ve a 3,5mm jack wired headset with mic (3 stripes for audio) and a mobile phone without 3,5mm jack.
@@Mindfulskeptic- maalesef, ya sesi kaynaktan alıp kulaklığa veriyor ya da bağladığın cihazın sesini aktarıyor. İkisini bir arada yapamıyor. Ben oyun için denemiştim ama gecikmesi oyuna müsaade etmiyor. Ayrıca içindeki codec ten mi bilmiyorum ama ses kalitesini düşürüyor. Standart kullanıcıların anlayacağı kadar olmasa da düşüyor. Ezcümle, bi işe yaramaz :)
I have had my Tao Tronics 2 in 1 since January and love it, but now it just won't turn on. It won't turn on after I hold the bottom down for 5 seconds or longer. What can I do to turn it on?
Hi, can I connect TT-BA07 to the 3.5mm audio jack of my iPhone 6 and have "aptx" bluetooth transmission? (Obviously, I shall be pairing my BT headphone to TT-BA07 instead, and keep the iPhone bluetooth turned off). iPhone does not have aptx support on BT. Thus, I am thinking about this alternative way to keep high fidelity audio listening when using BT headphone. I play wav and flac and other lossless format. Thank you very much.
Hi Eric, if you want to enjoy a high fidelity audio, aptX supported headphones is also required to work with this unit. Otherwise, the audio will still be coded via SBC codec.
I just bought your TT BAO7 to use with my Samsung s8 so my wife and I can listen together as we walk. I place it in a clip on my waist. It goes in and out, meaning that one of us or the other can not hear at the same time. Sometimes it comes back Other times it does not. Do you have a solution for this? With experimentation when I hold my hand up to my chest we both can hear it. Any suggestions? What are the best Bluetooth headsets to use?
Will this device work plugged into equipment in gym thru wireless headphones? I purchased one and cannot get it to work. It pairs to my iwatch when I plug it in but NO sound at . all. Please guide me in the right direction.
I have a question. Can I connect the microphone and speakers from my bluetooth headset to the adapter on my computer at the same time? I have microphone and speaker connection individually. Thanks for answers.
Hi. Re adding a second speaker. ( @ 1-56) I understand 2 speakers can be `paired`, then added as shown....... But,, Can the device actually transmit sound to both speakers at the SAME time ???. ( @ 2-00 in video,,,are both speakers actually playing ? or just `paired` ? ) The reason I ask is I have a similar device. and can pair 2speakers, connect 2 speakers, but can only actually transmit to one speaker at a time. I.E. ... After the initial pairing and connection,,, turn speaker 1 off and speaker 2 connects, or turn speaker 2 off, and speaker 1 connects.... but never both together. Does the TT-BA07 allow transmission to both speakers simultaneously ? Many thanks
Hi, TT-BA07 allows transmission to both speakers simultaneously. Please follow the instructions: 1. Pair the TT-BA07 with your first device. 2. Turn off the Bluetooth® function on your first device, tap the Power Button twice to pair and connect to your second device. 3. Turn on the Bluetooth® function on your first device. In approximately 30 seconds, the first device will automatically connect in. When you pair with two devices, both can play music at the same time.
I recently bought your wireless stereo transmitter. I am trying to connect the device to my speaker. I have a brightech brightplay bluetooth attached to the speaker. No matter what I do it will not connect. I was wondering if you could help. There are no buttons on the speaker, so I don’t know how i would put it in pairing mode. The attachment on my speaker is A2DP supportive.
Hello, I recently purchased your TA-BA07 Bluetooth Transmitter. I would like to pair it to the Bluetooth enabled radio in my 2016 Honda Civic so that I can transmit my XM radio to the car radio. The transmitter will not pair with the car radio. Any help or insight you can offer is greatly appreciated.
Would you kindly reset the TT-BA07 (switch the mode to RX, then switch back to TX) after it is turned off for 5 seconds, then re-pair in TX mode to see if this helps? 1. Place Honda Civic in "Pair Mode" and within 3 feet of the transmitter firstly. 2. Press and hold the Power Button for 5 seconds (LED flashes blue slowly) and tap twice to enter pairing mode (LED flashes red and blue alternately). 3. The two devices would connect with each other automatically, the Blue LED stays solid. 4. Connect the transmitter into your XM radio, the audio would be transmitted to your Car radio. Please make sure that any other Bluetooth signal around is turned off. BTW, here is the video about how to pair TT-BA07 on Amazon for your reference: www.amazon.com/Bluetooth-Transmitter-Receiver-TaoTronics-Simultaneously/dp/B01EHSX28M If it still can't work, could you please contact us? support@taotronics.com
I have been trying to pair this with my tbi bluetooth earbuds and only been able to do it once and lost connection. Please help. How can I get them to work?
yes i have a question. if i conntect it to my audio card on the pc, can i use audio card software to improve sound like i do with something connected with cable?
Can i use this adapter TT-BA07 to send audio from my TV to bluetooth 4.0 headphones? I didn't find any information whether it is compatible with BT 4.0 or not. Update: i bought it and it works!
Hi Dragooon0, yes, you can use it to send audio from your TV. If you have any extra question, please contact by email:support@taotronics.com. Our professional sales will solve your problem asap. Thanks!
Hey, thank you for your fast reply! I just asked this, because you're promoting it with BT 4.1 and there is no remark if it works with BT 4.0 headphones too.
I have it connected to audio out on tv and paired to my phone in receiver mode (only way it would pair), then have wired headphones connected to my phone. Yet the audio is still coming out if the tv. What am I doing wrong? Shouldn’t the audio be coming into the device and sending it to my phone?
I am having trouble listening to 2 speakers thru alexa dot. I have paired both speakers to tt-ba07 in tx mode. when I plug it into alexa only one speaker plays. when i turn on the other speaker all sound stops? I have been tring for days to get this to work please help. thanks
I purchased this for my car. My iphone pairs and plays music and audio from apps and videos but audio from calls does not transmit through the speakers. Any suggestions for how to resolve this issue?
I have followed the instructions to pair perfectly but I'm not able to connect my Airpods Pro with the TT-BA07. Has anybody tried this and succeeded? Also, does the TT-BA07 transmit from an iPad (if I connect it via the wire)?
Mine says it’s paired with echo dot and Bluetooth speakers from tv but still have tv speakers playing. Tried both connections they sent. My tv is a ROKU. Any help? Looked for a way to contact support but didn’t see a way.
Armando Ponce de Leon : good question I don’t see why not it’s worth a try I have a non Bluetooth projector and a non Bluetooth surround sound was thinking of trying it will see
ever paired this to a harley bluetooth radio? very interested as I'm looking into it for sirius radio for my bike. the older bikes had an auxiliary port 14 and up don't and even the 2000 dollar upgraded infotainment systems require a 400 dollar part to use sirius so if this product works could be a big money maker.
Fyi if your like me and just plug things in. Yea dont. Just set your earphones and adapter next to each other. No plugs nothing on adapter Pair the 2 (solid blu on both devices) plug the aux cord into adapter then on other end plug into aux out in tv Boom your connected. Took me days till i found this video. Ty
I really wish it worked that well. I've been trying for 2 days to pair my TT-BA07 to my motorcycle helmet speaker bluetooth receiver. Like hundreds of times. It simply will not pair. the helmet headset times out and the TaoTronics flashes red/blue forever. I'm doing exactly what the instructions and this video describe.
Why doesn’t my phone automatically connect to the device? Everything says it will remember my device, but I always have to go to settings>bluetooth and connect manually
The issue im having with the tx/rx plugged into the tv, transmitting to wireless headphones is that it seems to only be transmitting when there is dialogue, when no one is speaking it cuts off... is this similar to what you're experiencing?
@@XandalorZ I've tried many ways to hook up a bluetooth transmitter on it and it has been a nightmare. A phone should be capable once a transmitter is added but this one just sucks and refuses to work with it. Bluetooth phone Jack's, bluetooth headphone transmitters, etc. I cant change the phone, but I want to be able to use a wireless headset (and not cost $200 before buying the headset). It seems theres no way. Tech is worthless without total widespread applications imho.
I think I'm going to buy this, but quick question ! - Do you just leave the device always plugged into your tv (if you're pairing wirh bluetooth headphones for example). Or do you need to charge the device or can you even take it out or something? Not sure if you leave it in the tv for ever or not
Can someone say to me if there is some static noise in the background when connected? I bought another Bluetooth transmitter from another brand and it has that problem.
No I have had mine connected (paired) to my Oontz Angle 3 speakers for Years and there is no static noise of any kind. I listen to You Tube music through my laptop and plug the TaoTronics TT-BA07 2 into the computer. In fact I carry the speakers to the floor below my computer room and they have nice range and work Very Well without any static! Hope this helps! Have a great day!
@@briandawson3167 Thank you for the reply... This one I bought was a little bit frustating to me. It's not a clear connection like we have with cellphones. I'm considering to buy the Taotronics now. Have a nice day too!
I need to factory reset this device. How can this be done? I paired a bluetooth device that ended up having to be factory reset due to volume issues and now the TaoTronics won't pair with it again. Thanks!
for what it is worth....after reading all of these negative comments.. i was all ready to send this back... (i was trying to connect my blue tooth headphones to my non blue tooth old tv.. ) .. following the instructions didnt seem to make any sense, so finally i just plugged the adaptor into the TV and turned on my headphones... CONNECTED.. volume is fine, no delay,, no problems at all.. works perfectly and no issues
I struggled trying to connect this device to my TV. I tried pairing it when it was connected to the TV. Finally, I removed the transmitter from the TV and paired it separately with my Bluetooth capable headset. Once paired, I then inserted the device into the audio output of the TV and it worked perfectly.
Thank you, I bought one to turn my tv into blue tooth capable.
Still can’t get it to pair
Brian Rardin ...I’m good now Brian. Thanks!
I have an LG 7000 and can’t seem to find an audio output to connect the transmitter to. Is there any other way to connect it so I can hear sound out of my Bluetooth earbuds?
@@daniiii0825why don't you use the USB output ?
For those having trouble with playback on 2 devices at the same time. Make sure that the device you are transmitting from is not pairing directly to your other two devices. For example, I use this transmitter to hook up my Amazon Alexa to two different external speakers located on separate floors of my house. I was having trouble playing music through both speakers at the same time. Realized that Alexa had (on her own, I think) paired with each speaker separately. Went into the Alexa app, unpaired both devices, followed set up instructions for the transmitter and both are working perfectly and simultaneously with no lag.
I am able to pair 2 bose head sets, however one headset is getting disconnected automatically in 3 min approx .. voice is not clear on 2nd headset either its choppy ...
Could you please advice if this can be fixed ?
Definitely ni issue with bose headsets as its working fine with single pairing
@@karthik1942I'm not sure if your issue is the same as the one I was having, but make sure that the primary source you are transmitting from is not paired individually with either headset. In other words, make sure that your headsets are paired only to the transmitter.
You would think that for a company who makes audio equipment, they could use a simple pop filter on the mic when they record audio voice overs.
Nice little unit. Works well for me - 30ft range no walls, 20ft range ground floor with two walls to get through. Upstairs, just through ceiling, around 25ft.
Pairs quickly for me with portable speaker or earphones. Approximately one-word lag when used. Out of sync can be easily seen when watching lips move on TV, but that's to be expected due to transmission lag conversion both ends. Listening to music no problem whatsoever, but don't use if you need exact sync receive - you'll be one word or note delayed! Well worth the money to be able to select either TX or RX. Quality product.
Hi lain, thank you for your feedback! We're very happy to hear that the unit can meet your demands.
Thank You Soo Much for explaining this pairing mode. I was trying to pair with the wonderboom for 3-4 days and couldn’t do it until I saw your video to do it.
I thought mine wasn't working correctly for my projector to my JBL Boombox but I had the device plugged into the AV jack instead of the headphone jack. Now it works. I'm going to check the sound delay time next.
In receiver mode would be able to connect to my console and my phone simultaneously? Because I’m looking for a way to hear my gaming effects and be able to chat on discord at the same time.
i used this device to be able to make my tv Bluetooth enabled and it works like a charm
Hey can you pleaae help me? i paired with headphone but still sound come from tv and headphn as well. As i connect comcast via hdmi.any solution please
@@ramanjeetsingh6604 maybe change TV’s audio output setting to aux or audio out only.
I have recently purchased two TT BA07 through Amazon and was using it perfectly fine for last 2 months while paired with each other..one in TX mode and the other RX mode..
and suddenly one of the TT BA07 set to TX mode stopped transmitting audio...they sync together perfectly but the one of them doesnt have a proper audio coming out...there is either no audio or a sound some kind of a bad connection...i cross checked with multiple other cables and paired with other devices ..the situation is same.
Please help.
What should i do?
helpful and straightforward....perhaps a small suggestion is to demonstrate the wireless headphones for use on airplanes...
once you set up the TV and blue tooth headphones, does the tv speakers get muted and you hear the sound only on the headphones, or the tv speaker will also work so while you can hear the tv with the headphones and someone else in the room without headphones can also hear the tv?
Once paired, does it automatically connect when plugged into charger?
I've 4.1 bluetooth headphones (sony wh-ch700n) which I want to connect to a bluetooth 5.0 transmitter. Does this give me all the benefits of the 5.0 such as: lower latency and distance? Or do both advices need to have 5.0 to work optimal. I appreciate all the help!
I have a lot of problems connecting. Sometimes it works first try, sometimes it takes me am hour of reseting my headphones and the transmitter multiple times. I don't think it's a good product personally lol
I like how you screenshoted a meme and tried to put the picture as your pfp
I can still see the "Thomas has never seen such bullshit before"
Yep, thats the joke fam. Still isn't the best product with lots of issues, I recommend shilling out more cash for something nicer lol
How the blank do I connect my non bluetooth tv to my blue tooth Sony headphones?
Hi, I wonder if I can connect 1 taotronic in Tx mode to another one in Rx mode? I need to pair 1 analog mixer to my in ear headphones. Is that posible?
Since my iPhone is Bluetooth can I connect it wirelessly to the phone and then use wired headphones plugged into the phone? I’m connected but no luck.
does this support bluetooth 4.2 used by my original AirPods pros? I know it supports bluetooth 5.0, but does is it backwards compatible? Thank you in advance.
Hi. We are so glad to tell you the answer is yes as this adapter is backward compatible.
I've come to find that my beats x headphones volume function gets disabled when paired to this. The volume stays way too low to use. Other Vmoda wireless 2 headphones work flawless. Must return due to this incompatibility
I can’t even hear mine at all
Having the same issue. Works well with other Bluetooth devices but the Beats ear buds have low volume and cant be raised
I have a question. I work with a metal detector that does not have a wifi and bluetoth connection, can I with this taotronics device take the signal from the detector out there on the 3.5mm jack to connect it to this Taotronics transmitter and get the sound on my smartphone . thanks in advance for the reply regards for all
I'm using this product with Airpods 2 and MBP 15 and the volume is very low. The battery was fully charged and I tried with the charging cable connected as well. Any thoughts?
To answer everyone's question about pairing two of these units together, one transmit mode and the other in recieving (Tx to Rx).. yes you can. At the time of this posting i just did it two minutes ago and it worked flawlessly with my Samsung Galaxy S8.
Secondly, you may be wondering if you can connect this to another model such as the TAO 08 model which is just a reciever with play, volume control, mic to and answer calls.. yes you can pair to this unit as well.. as long as one transmit and the other recieves you should be able to pair..although if one has a mic and the other doesn't you may not be able to use that feature.. i dont have 2 to test but i will soon.
Not based on this review but in part on this review, I purchased this TaoTronics 2 in 1 Bluetooth adapter and found it less responsive than you have. I understand I might not have got a good one but the delay is there and I will be returning this one to Amazon.
Hi MrVeeBlog, if you have any question about this product, please feel free to contact: support@taotronics.com. Thanks again for your support!
I check the TaoTronics mentioned that in some comment:
Bluetooth is not an instant transmission protocol and there are some lag / delay due to the time it takes for the signals to be encoded and transmitted. Typically if you're listening to music or audio only, you won't ever notice this lag. However, pair audio with video or use Bluetooth devices with musical instruments where the user expects instant feedback and it is noticeable.
Here is the link of the discussion:
www.amazon.com/there-delay-between-what-hear/forum/Fx20B5FQTMI4R62/Tx2DF93XXS5QKZF/1/ref=cm_cd_naredir?_encoding=UTF8&asin=B00GKEAQ2M&ref_=ask_dp_lsw_al_hza
Thanks for the feedback Lianziko L. I find it just a little self-serving for a company to suggest that I should simply "get used to the lag" while using it for the purpose I bought it, for my TV. As Bluetooth technology gets better, I suspect this problem will be a thing of the past.
Thanks. we follow the video guide to pair two BT headphones (TX mode) and it work just same as your video guide but ONCE only. When we use it again, it had no response so that we follow the video guide to connect the (same) BT headphones again .
Based on the lighting signal, both BT headphones should be connected to TT-BA07 already . However, there only the 1st BT headphone have voice but the 2nd BT headphone is no voice. do you know how to fix this problem ?
When you pair the two bluetooth speakers together are you using a phone, laptop, or tablet. I'm waiting for my Tao to arrive and am going to be trying to connect two bluetooth speakers to either and Iphon or laptop and wondering if one was easier than the other. Thanks
if I have two of these TTBA07 devices, can I use one in RX and the other in TX and pair them? This setup is useful when you have a non-Bluetooth TV and speakers. Thanks in advance!
Eickel Mendez : I asked the same question no response I think it can be done I’m going to order another one and try it
Works great. One small issue. While in transmit mode, whenever there is a pause in sound, the device mutes and resumes when there is noise again. I assume this is to block out any hiss or ambient noise. Is there a way to shut that off? I find it a bit irritating. I would like to hear the sound unaltered
I am trying to use TX mode to pair from tv to AirPod pros. The issue is it is pairing with random devices and potentially even my neighbors devices. I have successfully paired it once but through trial and error. Is there a way to have it pair with my airpods first?
I am trying to pair this with my 2015 Audi A5 so I can play my iPod. It recognises the device but keeps saying that pairing had failed. What can I do to get it to pair?
on My Sony tv which port(back side) i supposed to connect??? on my sony bravia x800g TV?? i wan to connect my wireless head phone for TV...
If I plug this into an iPod nano 3rd generation can i connect bluetooth headphones?
Yeah, can the iPhone receive a signal from the transmitter in tx mode ?
Hi Taotronics, I can't connect my transmitter TaoTronics TT-BA07 with my Pioneer headphones. Can you tell me please if both are compatible?
I just bought the TT-BA07 in hopes of being able to use one pair of headphones for my PC and my iPhone. My headphones are TaoTronics TTBH-10. I am having a lot of issues with getting the iPhone and the headphones to both be connected at the same time. I know that the TT-BA07 us a multi-point device, so in theory everything should work; however, I am having problems getting them to play together. The situation is perhaps complicated by the fact that I have an Apple Watch, which is also connected to my iPhone. Is there a way of making this work? I find the procedure for pairing mutiple devices confusing, so perhaps I'm just doing it wrong. Any help gratefully received.
Thank you! I followed your steps and they worked for me.
can i pair 2 of them to one another? i currently bought 2 and want to pair them to one another if possible
is this device can transfer headphone's microphone? I' ve a 3,5mm jack wired headset with mic (3 stripes for audio) and a mobile phone without 3,5mm jack.
Dostum bu soruya cevap buldun mu?
@@Mindfulskeptic- maalesef, ya sesi kaynaktan alıp kulaklığa veriyor ya da bağladığın cihazın sesini aktarıyor. İkisini bir arada yapamıyor. Ben oyun için denemiştim ama gecikmesi oyuna müsaade etmiyor. Ayrıca içindeki codec ten mi bilmiyorum ama ses kalitesini düşürüyor. Standart kullanıcıların anlayacağı kadar olmasa da düşüyor. Ezcümle, bi işe yaramaz :)
I have had my Tao Tronics 2 in 1 since January and love it, but now it just won't turn on. It won't turn on after I hold the bottom down for 5 seconds or longer. What can I do to turn it on?
Very good explanation, right to the point, thanks.
Where do I plug it into my tv? I have 2 TVs, one has a sound bar and the other does not. Both are on cable boxes.
Hi, can I connect TT-BA07 to the 3.5mm audio jack of my iPhone 6 and have "aptx" bluetooth transmission? (Obviously, I shall be pairing my BT headphone to TT-BA07 instead, and keep the iPhone bluetooth turned off). iPhone does not have aptx support on BT. Thus, I am thinking about this alternative way to keep high fidelity audio listening when using BT headphone. I play wav and flac and other lossless format. Thank you very much.
Hi Eric, if you want to enjoy a high fidelity audio, aptX supported headphones is also required to work with this unit. Otherwise, the audio will still be coded via SBC codec.
How does it work with a non Bluetooth device such as my iPod shuffle ? Thank you for your video
Can you use dual headphones on this 1 transmitter? Like 2 sets of headphones?
You have 4 ears?
I just bought your TT BAO7 to use with my Samsung s8 so my wife and I can listen together as we walk.
I place it in a clip on my waist.
It goes in and out, meaning that one of us or the other can not hear at the same time. Sometimes it comes back
Other times it does not.
Do you have a solution for this?
With experimentation when I hold my hand up to my chest we both can hear it.
Any suggestions?
What are the best Bluetooth headsets to use?
Will this device work plugged into equipment in gym thru wireless headphones? I purchased one and cannot get it to work. It pairs to my iwatch when I plug it in but NO sound at . all. Please guide me in the right direction.
I have a question.
Can I connect the microphone and speakers from my bluetooth headset to the adapter on my computer at the same time? I have microphone and speaker connection individually.
Thanks for answers.
Hopefully it helped you。
www.taotronics.com/bluetooth-transmitter-help-guide
If you have 2 ttba07s can they send to each other? One sender, one receiver?
Hi. Re adding a second speaker. ( @ 1-56) I understand 2 speakers can be `paired`, then added as shown....... But,, Can the device actually transmit sound to both speakers at the SAME time ???. ( @ 2-00 in video,,,are both speakers actually playing ? or just `paired` ? )
The reason I ask is I have a similar device. and can pair 2speakers, connect 2 speakers, but can only actually transmit to one speaker at a time. I.E. ... After the initial pairing and connection,,, turn speaker 1 off and speaker 2 connects, or turn speaker 2 off, and speaker 1 connects.... but never both together.
Does the TT-BA07 allow transmission to both speakers simultaneously ? Many thanks
Hi, TT-BA07 allows transmission to both speakers simultaneously. Please follow the instructions:
1. Pair the TT-BA07 with your first device.
2. Turn off the Bluetooth® function on your first device,
tap the Power Button twice to pair and connect to your second device.
3. Turn on the Bluetooth® function on your first device.
In approximately 30 seconds, the first device will automatically connect in. When you pair with two devices, both can play
music at the same time.
@@TaoTronics_official Thank you very much.
Tem algum atraso ? Consigo usar na saída de fone de uma câmera… como transmissor… e emparelhar em um phone bluetooth???
How do I pair my transmitter to my 65t Jabra Bluetooth earbuds? I using a hd desktop radio with the output jack.
I recently bought your wireless stereo transmitter. I am trying to connect the device to my speaker. I have a brightech brightplay bluetooth attached to the speaker. No matter what I do it will not connect. I was wondering if you could help. There are no buttons on the speaker, so I don’t know how i would put it in pairing mode. The attachment on my speaker is A2DP supportive.
Hi Sophia, thanks for your support! Please contact our professional sales: support@taotronics.com, they will help to solve your problems. Thanks!
I have a car it has Bluetooth already but I have an old iPod W/ some of my favorite music. Would I B able 2 Bluetooth my old iPod to my car????
Hello, I recently purchased your TA-BA07 Bluetooth Transmitter. I would like to pair it to the Bluetooth enabled radio in my 2016 Honda Civic so that I can transmit my XM radio to the car radio. The transmitter will not pair with the car radio. Any help or insight you can offer is greatly appreciated.
Would you kindly reset the TT-BA07 (switch the mode to RX, then switch back to TX) after it is turned off for 5 seconds, then re-pair in TX mode to see if this helps?
1. Place Honda Civic in "Pair Mode" and within 3 feet of the transmitter firstly.
2. Press and hold the Power Button for 5 seconds (LED flashes blue slowly) and tap twice to enter pairing mode (LED flashes red and blue alternately).
3. The two devices would connect with each other automatically, the Blue LED stays solid.
4. Connect the transmitter into your XM radio, the audio would be transmitted to your
Car radio.
Please make sure that any other Bluetooth signal around is turned off.
BTW, here is the video about how to pair TT-BA07 on Amazon for your reference:
www.amazon.com/Bluetooth-Transmitter-Receiver-TaoTronics-Simultaneously/dp/B01EHSX28M
If it still can't work, could you please contact us? support@taotronics.com
do I have to have this plug in my phone for it to pair two speakers ?
i am cirous my headset's microphone do work with PC?absoultly need three line aux cable i think
I have been trying to pair this with my tbi bluetooth earbuds and only been able to do it once and lost connection. Please help. How can I get them to work?
Hi can you pair two TT-BA07 devices together one as a transmitter other as a receiver?
yes i have a question. if i conntect it to my audio card on the pc, can i use audio card software to improve sound like i do with something connected with cable?
Works great...thanks for the video.
Hello, I need to paire using the L&R cables but didn't work, any clue?
Yeah, I am only able to hear it from only my left side of any headphone/ear buds used to pair it with. Is it only supposed to do that? :/
Can i use this adapter TT-BA07 to send audio from my TV to bluetooth 4.0 headphones?
I didn't find any information whether it is compatible with BT 4.0 or not.
Update: i bought it and it works!
Hi Dragooon0, yes, you can use it to send audio from your TV. If you have any extra question, please contact by email:support@taotronics.com. Our professional sales will solve your problem asap. Thanks!
Hey, thank you for your fast reply!
I just asked this, because you're promoting it with BT 4.1 and there is no remark if it works with BT 4.0 headphones too.
Yeah, it is also works with BT 4.0 too. Dont worry.
Ok thanks!
+Dragooon0 with Bluetooth headphones can you control the volume
I have it connected to audio out on tv and paired to my phone in receiver mode (only way it would pair), then have wired headphones connected to my phone. Yet the audio is still coming out if the tv. What am I doing wrong? Shouldn’t the audio be coming into the device and sending it to my phone?
You should pay me for the time I wasted trying to make this product work.
PS: Playing loud background music is not helpful!
I am having trouble listening to 2 speakers thru alexa dot. I have paired both speakers to tt-ba07 in tx mode. when I plug it into alexa only one speaker plays. when i turn on the other speaker all sound stops? I have been tring for days to get this to work please help. thanks
does it work with nintendo switch and jbl t450bt?
This little thing works GREAT!
Thank you soooo much for your video, it was so easy and enjoyed my classic iPod, first generation. Used my sound bar and it was awesome!!!!!
I purchased this for my car. My iphone pairs and plays music and audio from apps and videos but audio from calls does not transmit through the speakers. Any suggestions for how to resolve this issue?
buy a new car?
Do the pairing work with two headphones of the very same brand and model? Thanks
I have followed the instructions to pair perfectly but I'm not able to connect my Airpods Pro with the TT-BA07. Has anybody tried this and succeeded?
Also, does the TT-BA07 transmit from an iPad (if I connect it via the wire)?
How do you know when it is fully charged and how long will it last between charges
Mine says it’s paired with echo dot and Bluetooth speakers from tv but still have tv speakers playing. Tried both connections they sent. My tv is a ROKU. Any help? Looked for a way to contact support but didn’t see a way.
Please try to change the settings on your TV to PCM.
Thanks a lot for the video,I clearly understand you many thanks Bro.
Damn brother you make it easy for me I love you
how do you unpair headphones from this device to add another after you have already added two devices?
Can i link two TT-BA07, one send and one receive?
Armando Ponce de Leon : good question I don’t see why not it’s worth a try I have a non Bluetooth projector and a non Bluetooth surround sound was thinking of trying it will see
ever paired this to a harley bluetooth radio? very interested as I'm looking into it for sirius radio for my bike. the older bikes had an auxiliary port 14 and up don't and even the 2000 dollar upgraded infotainment systems require a 400 dollar part to use sirius so if this product works could be a big money maker.
Hi Jordan, sorry we have every had a test of the unit with harley radio. But we do have customers that successfully use it to work with radios.
This. Tutorial help me. Thanks. Now Is working on my switch
Fyi if your like me and just plug things in. Yea dont. Just set your earphones and adapter next to each other. No plugs nothing on adapter Pair the 2 (solid blu on both devices) plug the aux cord into adapter then on other end plug into aux out in tv Boom your connected. Took me days till i found this video.
Ty
So if my TV does not have an audio jack I can use the RCA plugs to transmit the noise to my Bluetooth headphones?
Hi can I connect co wired mic and true Bluetooth connect to a smartphone? Thanks
Hi Renato, sorry but have to tell that this unit does not work with mic.
Trying to connect and watch chromecast and play video games via HDMI how would I set this up? my TV also doesn't have a aux port
You would need to connect it to the audio out plug on the tv for it to works or headphones plug
I really wish it worked that well. I've been trying for 2 days to pair my TT-BA07 to my motorcycle helmet speaker bluetooth receiver. Like hundreds of times. It simply will not pair. the helmet headset times out and the TaoTronics flashes red/blue forever. I'm doing exactly what the instructions and this video describe.
DFWKen Try either TX or Rx mode I had similar issue but it connected
Is it possible to pair the TT-BA07 with your TT-BH06 wireless headphones?
Hi Logan, yes, you can pair the TT-BA07 with the TT-BH06 headphones, they are compatible to each other.
Why doesn’t my phone automatically connect to the device? Everything says it will remember my device, but I always have to go to settings>bluetooth and connect manually
My audio sounds very robotic on my headphones. How can I fix it
Buy a different one
And give me the numbers on your credit card
The issue im having with the tx/rx plugged into the tv, transmitting to wireless headphones is that it seems to only be transmitting when there is dialogue, when no one is speaking it cuts off... is this similar to what you're experiencing?
HI, does it work with apple airpods.
can I make a phone call with this device using a wired headphone connected to in?
does it work with a ipod nano shuffle?,thanks a lot..
Hi Alexis, yes, TT-BA07 is able to work with ipod shuffle.
i have two TT-BA07 is it possible to send using one and receive using another one plz give me the rply
Hi Sahaya, please contact our professional sales on support@taotronics.com. We will solve your problem asap. :)
How do I get this to work on my Cisco CP7965G?
It won't. That phone isn't bluetooth compatible.
@@XandalorZ I've tried many ways to hook up a bluetooth transmitter on it and it has been a nightmare.
A phone should be capable once a transmitter is added but this one just sucks and refuses to work with it. Bluetooth phone Jack's, bluetooth headphone transmitters, etc.
I cant change the phone, but I want to be able to use a wireless headset (and not cost $200 before buying the headset). It seems theres no way.
Tech is worthless without total widespread applications imho.
Can I Connect one as Tx and other one as RX, between two of them??
I think I'm going to buy this, but quick question ! - Do you just leave the device always plugged into your tv (if you're pairing wirh bluetooth headphones for example). Or do you need to charge the device or can you even take it out or something? Not sure if you leave it in the tv for ever or not
Toby Bromfield has a 6 hour battery life. But u can plug the charging cable to a free usb port on the tv to keep it always charged
is the charging cable micro usb or usb-c?
Micro
Can someone say to me if there is some static noise in the background when connected? I bought another Bluetooth transmitter from another brand and it has that problem.
No I have had mine connected (paired) to my Oontz Angle 3 speakers for Years and there is no static noise of any kind. I listen to You Tube music through my laptop and plug the TaoTronics TT-BA07 2 into the computer. In fact I carry the speakers to the floor below my computer room and they have nice range and work Very Well without any static! Hope this helps! Have a great day!
@@briandawson3167 Thank you for the reply... This one I bought was a little bit frustating to me. It's not a clear connection like we have with cellphones. I'm considering to buy the Taotronics now.
Have a nice day too!
can I use it to send image from my phone to TV and hear at same time on my Bluetooth speaker?
Hi Nacy, sorry but have to tell that this unit is only for audio transmission, and is supported to work with cell phones only in RX mode.
Nancy Bonilla z😂😂😂
I need to factory reset this device. How can this be done? I paired a bluetooth device that ended up having to be factory reset due to volume issues and now the TaoTronics won't pair with it again. Thanks!
Hopefully it helped you。
www.taotronics.com/bluetooth-transmitter-help-guide
Rocky Liu I was able to finally get it paired with my defiant beats x headphones but there is another issue I listed above.
Can i use this product to connect two speakers with an iphone?
Hi Keith,yse, TT-BA07 is able to stream audio to two stereos simultaneously.
How to pair with an iPod?
Thanks a lot!