It was a lot easier to use the stock style internal hydraulic slave cylinder/throw out bearing for a nv3500 with the original quick connect line that came on the s10 running to the clutch master cylinder
Get a longer bleeder line so you can run it in your engine bay and be easier to bleed the clutch just a suggestion that's how I have it in my ls swap bmw 535i
New subscriber Following! Since I can’t afford a T56 and all the AR5 has went through the roof also guess my last hope to get a manual transmission in my 1988 Monte Carlo SS is a NV3500
4.8 with nv3500 here why not use the 4.3 throw out bearing it works fine and is available everywhere I stay away from that aftermarket stuff when possible
could have saved money. All 1996 and up GM truck manuals went to that internal slave. You could have looked up a 1996-2000 nv3500 from a 1500 truck or s10 and it would be the right part.
@@petrolhead8851 it’s not that you can’t ask but if you do watch you would know a while back when the S10 truck became the focus both Venom and Gotham were done and not going to be builds after that.
Hey y’all I got a 99 Silverado swapped with a 6.0 vortec and a manual transmission from a v6 it won’t start from the key but I can start it through the screw driver on the starter any ideas neutral safety switch is new starter is new
Hey bro I had the exact same issue, I had to follow the pink remote switch from the starter to the fusebox, and I had to wire it to the starter relay if that makes sense. I'm pretty sure it happened when I had PCM issues and my clutch switch wouldn't activate
Ok so I been looking for answers and nothing. I posted this question a couple weeks ago with no answers. Maybe you got an answer please!!! Here's my post. Ok I need someone that has experience with nv3500s bolted to an LS. I went NV and did all the measurements and got it within specs. Here are my measurements Release bearing to front of trans 3.8" Engine to fly 3.35" distance From my understanding spec needs to fall in line with .125"-0.2" (mid .1625) unless someone has a different spec please let me know. That being said 3.8-3.35=.45" So I take that .45"-.1625= .2875 ( I did minus .1625 to keep it somewhere in the middle of spec allowed) I got a 10 pack of .05 spacers so I decided .1625/.05=5.75spacers I put in 6 spacers times .05=.3" So if my math is correct I take .45"-.3"=.15 and puts me in between the .125"-.2" range. For all you who followed the math so far and not racking there brain I put the trans on and when I did I feel like when pushing it on to the engine I can feel the tranny spring back like if the release bearing is to far forward. I ended up pushing it on and bolting it up. I pressure bled the system and the tranny won't go into any gear at all. I have been told two different things from friends, one person said to many spacers that tranny is should go in easily and not feel a push back at all and could be binding. Another person I spoke to said if the release bearing was to far forward than it would be engaged the entire time and go in to gear. Any advice welcome please!
So is this for the setup on a NV3500 with internal space? Or is that an external slave one? Looks internal but I’m in the same boat right now trying to find parts to mate my Nv3500 to my 5.3 ls.
@@deadbeatgarage Soon as I get a spare, brother.. 😁 I understand, man..my ride is a mustang, and I'm a po' boy.. It wants a T56 or a TKX, but if makes do with a whole stack of junkyard T5s. At least the T5 r&r's quickly when I grenade one.. The NV3500 in my work truck is usually an all day job, and the dang things are getting scarce, yanno?
@@antuanperez426 Far be it from me to praise a slushbox, but a 4L60E is rated at 360 foot pounds of torque, the NV3500 tops out at 300 foot pounds.. You can take the slushbox to a trans builder and have it modded for serious power...not so much the NV3500. It's an upgrade over walking, but not much. 😁
Someone HELP me out here @ 3:05 clearly the diameter of the hole in the flywheel is substantially larger than the pilot bearing, isn't the Pilot bearing supposed to fit in the flywheel? I'm running into this exact issue right now, doing the clutch on my '07 Fit sport (usdm), ordered a LUK clutch kit & a lightweight flywheel. Compared them & the flywheel center hole is exactly as pictured on Bravus' set up here, the pilot bearing is way smaller.
@@ryurc3033 I doubt you'd make three full passes..my 4.3 (mostly) stock '95 C1500 eats these damn things like potato chips. If it's gonna be abused swap in an NV4500 from a 3/4 or 1 ton..not a race trans by any means, but it'll fit most anywhere the 3500 will, and it'll survive.
Here's to all of us that still have to use keys to open our doors!
My question is will the Nv4500 bolt up to any LS? Like a 6.0 Lq9?
Ayeee
@@SquareBodyK5 From everything I've seen yes you just have to buy the Bell housing
Nice attitude being so helpful,don't ever change.
When I done mine I ordered the complete kit for an 04 silverado rst from rock auto. It came with every part you need
What’s the part package number
Part number
Bro that’s been over 3 years ago I have no idea on the part number
It was a lot easier to use the stock style internal hydraulic slave cylinder/throw out bearing for a nv3500 with the original quick connect line that came on the s10 running to the clutch master cylinder
Get a longer bleeder line so you can run it in your engine bay and be easier to bleed the clutch just a suggestion that's how I have it in my ls swap bmw 535i
Great resource video for me, thank you, well done
New subscriber Following! Since I can’t afford a T56 and all the AR5 has went through the roof also guess my last hope to get a manual transmission in my 1988 Monte Carlo SS is a NV3500
Cant wait to see it running bro!!!!
Bless you I needed this info
Cool little video. More please. 😎👍🛠
Do more videos like this.
4.8 with nv3500 here why not use the 4.3 throw out bearing it works fine and is available everywhere I stay away from that aftermarket stuff when possible
So are you saying you can use the 4.3 internal slave?
Ive always used a bushing in the crank. That’s how they have been when taken apart also. Always wondered the difference.
could have saved money. All 1996 and up GM truck manuals went to that internal slave. You could have looked up a 1996-2000 nv3500 from a 1500 truck or s10 and it would be the right part.
Would it bolt up to the older nv3500 and is it plug and play or does it need to be shimmed
That was awesome to share 👏
The earlier NV3500s with the internal slave cylinders are better/easier to work on...
Progress, progress, progress. Hell yea man multiple projects all happening.
You will have to cut a window in the tranny to run the lines to the throw out bearing and bleeder.
the NV3500 doesn't have these holes already?
@@808kahulaa It does bro's prolly a little on the slow side
@@antuanperez426 , I pulled one from a '95 not long after I commented, the concentric slave is the one with the holes, from '97 and up.
Sweet! I CANT wait till you finally drop that motor in and get that first start up! By the way whatever happened to the Gothm build?
🤦♂️ dude come on at this point do you not watch the videos or are you new?
@@JustinFromThe206 I do Watch his videos but why CANT i just ask?
@@petrolhead8851 it’s not that you can’t ask but if you do watch you would know a while back when the S10 truck became the focus both Venom and Gotham were done and not going to be builds after that.
Great work. Good video.
Hey y’all I got a 99 Silverado swapped with a 6.0 vortec and a manual transmission from a v6 it won’t start from the key but I can start it through the screw driver on the starter any ideas neutral safety switch is new starter is new
Is the 6.0 engine from a 99-00 with the long crank?
Hey bro I had the exact same issue, I had to follow the pink remote switch from the starter to the fusebox, and I had to wire it to the starter relay if that makes sense. I'm pretty sure it happened when I had PCM issues and my clutch switch wouldn't activate
Where’d you get your research I to am attempting to do the same
Ok so I been looking for answers and nothing. I posted this question a couple weeks ago with no answers. Maybe you got an answer please!!! Here's my post.
Ok I need someone that has experience with nv3500s bolted to an LS. I went NV and did all the measurements and got it within specs. Here are my measurements
Release bearing to front of trans 3.8"
Engine to fly 3.35" distance
From my understanding spec needs to fall in line with .125"-0.2" (mid .1625) unless someone has a different spec please let me know.
That being said 3.8-3.35=.45"
So I take that .45"-.1625= .2875 ( I did minus .1625 to keep it somewhere in the middle of spec allowed)
I got a 10 pack of .05 spacers so I decided .1625/.05=5.75spacers
I put in 6 spacers times .05=.3"
So if my math is correct I take .45"-.3"=.15 and puts me in between the .125"-.2" range.
For all you who followed the math so far and not racking there brain I put the trans on and when I did I feel like when pushing it on to the engine I can feel the tranny spring back like if the release bearing is to far forward. I ended up pushing it on and bolting it up. I pressure bled the system and the tranny won't go into any gear at all. I have been told two different things from friends, one person said to many spacers that tranny is should go in easily and not feel a push back at all and could be binding. Another person I spoke to said if the release bearing was to far forward than it would be engaged the entire time and go in to gear.
Any advice welcome please!
I'm trying to p mate this up to my 1983 Pontiac Firebird Trans Am V8
So is this for the setup on a NV3500 with internal space? Or is that an external slave one? Looks internal but I’m in the same boat right now trying to find parts to mate my Nv3500 to my 5.3 ls.
If my NV3500 came off of a 97 Sierra, would I get a clutch for that model and year, or go ahead and do the s10 like you have
Looking forward!
I’m from Ireland. Is there anyway to contribute towards the build?
Why would you want to swap in a trans with internals made of peanut brittle & rock candy?
Would you like to ship me a t56?
Let me know, PO Box is in the description 👇🏻
@@deadbeatgarage
Soon as I get a spare, brother..
😁
I understand, man..my ride is a mustang, and I'm a po' boy..
It wants a T56 or a TKX, but if makes do with a whole stack of junkyard T5s.
At least the T5 r&r's quickly when I grenade one..
The NV3500 in my work truck is usually an all day job, and the dang things are getting scarce, yanno?
@@zrxdoug When the stock 4L60E is made out of jello, the NV3500 is a huge upgrade
@@antuanperez426
Far be it from me to praise a slushbox, but a 4L60E is rated at 360 foot pounds of torque, the NV3500 tops out at 300 foot pounds..
You can take the slushbox to a trans builder and have it modded for serious power...not so much the NV3500.
It's an upgrade over walking, but not much.
😁
Goat 🐐 #DBGarage
Could have gotten everything from a 04 silverado 4.8 make sure 04+ they usually don’t show up if it’s not 04 for some reason
Awesome
Gnarly 🤙🏼🔥🔥🔥🔥🔥
What is the part number for the adapter and extension line?
yooo watching this from the shitter at work
First! Let's go 🔥
Would that pressure plate and the flywheel work for a t5 transmission?
Someone HELP me out here @ 3:05 clearly the diameter of the hole in the flywheel is substantially larger than the pilot bearing, isn't the Pilot bearing supposed to fit in the flywheel? I'm running into this exact issue right now, doing the clutch on my '07 Fit sport (usdm), ordered a LUK clutch kit & a lightweight flywheel. Compared them & the flywheel center hole is exactly as pictured on Bravus' set up here, the pilot bearing is way smaller.
WTF DBFAM, not one reply? Guess nobody knows......
@@estewar03 Guessing you figured this out. The pilot bearing goes in the crankshaft, not the flywheel.
Do you happen to have the part number to that slave cylinder
Yes finally 🤙🏽
Why didn't you just get a direct fit slave cylinder throwout bearing
so......when does our merch ship?
When will the Halloween shits be sent out haven't got mine yet
👍👍from this guy
So will a NV3500 not work with the stock clutch fork and throughout bearing?
Does anyone have the list 😢
That looks like a -4 line tbh, not a -3... maybe Im crazy
Any chance i get my order this week? Order #4629 still not shipped and no word on it.
Nv3500 trans from what kinda v8 truck
Pretty sure he means the 4.3 nv3500 from the Blazer......
#Notigang
Ford ranger use that part
How much hp and tq can these handle
300 hp/ 300 tq+ sticky tire= broken in 3 runs
@@ryurc3033
I doubt you'd make three full passes..my 4.3 (mostly) stock '95 C1500 eats these damn things like potato chips. If it's gonna be abused swap in an NV4500 from a 3/4 or 1 ton..not a race trans by any means, but it'll fit most anywhere the 3500 will, and it'll survive.
@@zrxdougso the Nv4500 will bolt right up to a LQ9 6.0?in and 03 chevy silverado 1500 extended cab?