Error in initializing ST-LINK device. Reason: No device found on target

The summary:
1.) Disconnect your board from usb or other voltage supply.
2.) Connect the BOOT0 Pin with High (3V).
3.) Plugin the usb cable again.
4.) Download a write programm to the board which doesn’t configure the PA11 and PA12 Pins.
5.) Disconnect the usb again.
6.) Disconnect the BOOT0 from High (3V) again.
7.) Plugin the USB again and see if the board works normal again.
8.) Please like and subscribe for more videos
Error in launch sequence
Failed to start GDB server
Error in initializing ST-LINK device. Reason: No device found on target.
Target no device Found
STM32 ST-LINK Utility
CubeIDE
Problem Occured
Stlink device bulunamadı hatası
please like and subscribe for more videos

[@MertGONCU]

The summary:

[@gonya707]

Absolute legend. After browsing a lot of useless forum posts this is what worked for me. I understand the problem was caused because something overwrote the status of the boot pin and the MCU couldn't be reached. This are the steps I followed from this video:

[@matiashorst9757]

Thank you very much for your contribution! I was several days trying to solve this problem and I couldn't find the solution. You saved my project!

[@sezensonmez]

Thank you sir it's very helpful!

[@jirapong0hong]

It's work! Thank you.

[@enescanaman3333]

Sen adamsın adam eline emeğine sağlık.

[@syedumarjunaid5499]

thank you so much :)

[@user-gy4nq8vl5i]

YOU ARE MY HERO!!!!!!!!

[@rea1013]

Thanks mate, it works.

[@ofvigelosandammonia244]

BOOT0 ı 3 volta getirmek demek, üzerindeki sarı jumperı 1 tarafına atlatmak mı demek, yoksa başka jumper kullanarak 3.3V mu bağlayacağız?

[@calpardo]

STM32G030K6T6TR kullaniyorum ve PA14-BOOT0 pininde datasheette SWCLK'u alternate function olarak gostermis. Bu durumda bu sorunu nasil cozebilirim? CubeIDE'de SWD olarak configledim de debugger connected diyor sonra failed halting target diyor. Sadece garip bir sekilde CubeProgrammer'da hot plug moduyla cipe baglanabildim onda da option byte falan degistirmeye calsitim olmadi. Bu arada herhangi bir dev board kullanmiyorum tamamen her sey breadboardun ustunde ve stlinke nrst de bagli her seyi denedim olmuyor...

[@ariftukel6872]

thanks brother

[@rama8182]

Hi, I have problem ONLY with CubeIDE programming (now 1.10.1).

[@idrissnjoya1439]

thanks problem solved

[@mannguyen5781]

could you show me the way to activate the debugging feature, please? In case of program running, I think we only hold reset button on board. Thanks a lot.

[@alifioahmad_raihan]

Nice idea for STM32F103, how about with STM32F411 ?

[@chikiblogger]

Mira, no te entiendo ni media, el video me ha salvado el culo espero que la vida te vaya bien eres el puto amo. (U are a real fucking G)

[@lehutsoreginald2685]

Good day, Sir. I have a similar problem with STM32f429

[@abdullahcanbaz6429]

Hocam merhaba ben bu yolu denedim ama çözüm olmadı Boot pinini anlattığınız şekilde yapıyorum ama stlink utility den sadece görebiliyorum ne program atabiliyorum ne silebiliyorum hep hata alıyorum buna benzer kullanığım programlayıcı ve STM işlemci tamamen orjinal olmasına karşı driverler da güncel durumda

[@oktayacar1744]

Failed to start GDB server