Aprilia RS 125 2 Stroke - Engine Assembly Without Special tools - Part 5
HTML-код
- Опубликовано: 8 сен 2024
- Aprilia RS 125 Tuono part 5 - Engine assembly
Servus and welcome to my new video.
In this part 5 its time to assemble the prepared parts of the ROTAX 122 engine. We start with changing all seals of the water pump assembly. Afterwards the gearbox is put in the engine case and the shift parts follow. Now you can see pretty well how the shifting mechanism works and I try to explain it.
With a new gasket the second engine half can be mounted and tightened down. OF course we test every function all the time because you never know. Before the cylinder foot gasket can go on, the big middle gasket needs to be cut flush with the engine.
After that is done the clutch and other small plastic gears can be mounted in the right order and according to markings. With a new oring on the oil pump and a new shaft seal the clutch cover goes on as well. Next are the piston, cylinder and cylinder head. Every step is explained and shown in detail.
To run the machine you need electrical power so we mount the alternator. One of the last steps is to completely disassemble the power valve, clean it and throw it together with new seals and o-rings. It is very important that this part works correctly so we pay attention to it.
And because it is easy to reach at this point the last part is the sprocket.
At age 15 I bought a Honda NSR 125 - A very good bike, had a ton of fun with it. But like everybody in that age I always wanted a Aprila RS, because its the most powerful 125 2 stroke. But the prizes were higher and the cost for maintenance is also much higher, so I could not afford one.
More than 10 years later I had the chance to buy this RS cheap and now I have the skills to completely repair it.
I hope you enjoy my video and it helps you to repair your own stuff - because thats my intention!
Thank you for watching
If you would like to support me, please write a comment. That helps to get the video recognized. Thank you
Nice man, I also have rs 125, but there are not so many guides on it, yet your channel fix it. Especially on the Russian RUclips where I come from, you know when I bought Aprilia, (I have a full power of 2009), everyone from my friends told me why I need it, there are almost no spare parts in Russia, but when I opened the throttle I realized what it costs. Spare parts have to be brought all the way from Italy, in Russia (Moscow) there really are practically none, and not through an official dealer, but by asking friends living there to bring them by plane (they have dual citizenship). In short, thanks for the video, it helped a lot. By the way, it's very nice to watch of it even reminds me of a video like ASMR :D
Thank you for your comment and enjoy your bike
Начал собирать мопед по этому видео, в итоге получился неплохой солярис. В целом результатом доволен, мужик красава, годное асмр видео!🚗
Brilliant video, just what I needed for my RS125 re-build
Thank you. Have fun working on the engine. And btw I'm no professional 😉
Brilliant videos. Hopefully gonna restore an aprilia myself and your videos have been really helpfull and inspiring. Thank you for your time making them!
mishamcm thank you so much
What a great job!
I would like one day I will can have such knouwledge to do same by myself.
Congratulations!
Thank You!
This video helped out please I need more rotax 122 videos am really stuck :)
You find more on my channel :-)
Bikedogtor I will have a look am very happy to watch the videos
sehr gut,!
hi...video ini sangat membantu
Very Good
Thank you
Great Vid,Doc! You,re now my Go-To Guy for All engine work on my wee 125RS 1999mod. Brilliant wee engines in Finely crafted bikes,im sure you'll agree?!! Keep up the Sterling work...
Hey thank you and I'm glad the videos help. Have fun with your bike, it's great
It,s Nm and thanks for the clear video.
Fantastic video, i'm in the midst of this now on my own 125.
Thank you! I hope my videos help you to finish the project
Just got my 2nd one very good video.
Thank you for this, helped me a lot!
FeAr glad I can help
nice guy
Great video !
1:39 genuine Aprilia parts lists "Molykote 111" to be used here, which is a clear silicone compound, so I would say it checks out as correct.
hi..saya memiliki sebuah benelli rfs150i.ingin rebuild semula tapi tiada video seperti ini..
Nice work buddy!!!
Thank you :-)
Hi there! Excellent video, really! Do you have manual with measurements and other thing like what force is needed to screw things in that engine? If you have, could you share? Brilliant tutorial, just a normal guy making something with his hobby on yt! 🙂
Thank you, you find it on Google
Is the rs engine the same as the 04 Aprilia mx engine? If so this guy is a legend
I don't know sry
I’ve been told it is and looks the same to me. Thank you
Very nice video! I have just one question. I am about to buy engine from Aprilia RX125(rotax123). Dont u know if it fits? Is it the same engine with gearbox?
Hi, I don't know if it's the same
At 20:18 if you pause the video its the connector by your two fingers, looks like a hose should goto it, thanks again
Ahh yea that's just the breather outlet for the gearbox. Usually a hose is connected to it and goes up a little bit then down underneath the bike, end open.
@@bikedogtor1663 Ah great i thought it was a breather just wasnt sure if it had to connect anywhere, many thanks and keep safe mate
Great video!!! Find a cagiva mito next a make a video on it too!!!
dyu hi good point, before I bought the Honda NSR I nearly got a Cagiva Mito 🤔 really nice bike as well
@@bikedogtor1663 i think cagiva mito is alot better thn the aprilia rs125. Especially where i am from its rare to see a cagiva but the rs125 is relatively common
Hattest du Probleme mit dem Simmerring auf der Kupplungseite der Kurbelwelle? Habe genau so verbaut wie im Video und Motor saugt Getriebeöl an und verbrennt mit.
Nein hatte keine Probleme. Würde mich auch wundern wenn der so stark saugt dass dort Öl durch kommt. Das ist ja relativ zäh.
Good job, did you check the squish, that’s the different cylinder base gaskets, I am sure you did👍🇬🇧
Yes I tried with oil but it wasn't accurate enough. I ended up using the middle gasket and it runs fine.
I have always used a strip of solder in the plug hole and measure the squashed end , after slowly turning it over by hand.😁🇬🇧
The manual says to measure the amount of Milliliter to calculate the chamber. But as said I just used the middle gasket and it's fine. Although I would like to know if you feel the difference with another gasket.
I am old school, I have built things like rd350 power valves, rg250 ect- I understand how you have done it, if it runs and rides brilliant 👍. Not criticising the great work you have done, just love to see people work on 2 strokes, and do a proper job like you. I have gone to the dark side, I have a Kawasaki vn900 I am undecided if to bobber it 🤔 good luck with your great tutorials👌
Thank you, I didn't get your comments wrong. Actually I appreciate when people want to help 😊
Hi i have been watching your videos and they are great infomation good work, im in the middle of a rs125 restoration at the moment and the videos have been a great help, on the engine casing near the flywheel there is what looks like a pipe connector could you advice me what connects to it please as i cant seem to fine a pipe to connect to it. Many thanks and great work.
I dont know what you mean. Is it on the flywheel side or between the two engine cases?
Is it possible to push that crank seal in too far.....?
Yes
1:45 water grease 👌🏼it’s normal
When you change the gearbox oil? Shouldn't be that bad
How much compresion in head ?
I didn't measure that
Mein Auslass-Schieber sifft wie verrückt. Ich hab vor kurzem auch erst die Dichtungen gewechselt. Was könnte dran sein? Das Öl sifft anscheinend am der Schaft-Dichtung vorbei
Klingt erstmal nach zu viel Öl im Gemisch. Wenn das Öl nicht sauber verbrennt kommt es auch an neuen Dichtungen vorbei.
@@bikedogtor1663 Passiert das auch wenn meine Zündkerze nicht warm genug wird?
Fahre ja kein gemisch
Nein eher nicht. Vllt ist die Öl Pumpe verstellt oder das Gemisch zu fett
@@bikedogtor1663 Mir ist aufgefallen, dass meine Leerlaufdüsen (65) undso (Mischrohr) zu groß sind. Bestelle mit bald die passenden Düsen dann schau ich mal. Und ich fahre zudem die falsche Vergasernadel (X02). Hab auch deswegen vermutlich ein stottern bei 5-6k wenn ich die nadel im 2ten clip habe. Im ersten clip (von oben) läufts normal, jedoch muss ich dann die gemischschraube ziemlich weit raus drehen (4 umdrehungen), dass die beim gas aufreisen nicht abstirbt.
Denke das hängt parallel mit dem Austritt vom Öl zusammen
ps: Das modell war vorher gedrosselt (MP-01)
Ich hab ne rs 125 gefunden die seit 2018 steht. Will jetzt meine Eltern überreden ob ich sie mit holen darf (bin halt erst 15).Will dann auch den Motor überholen. Hab ne Frage zu der Ausgleichswelle, kann ich die ausbauen oder lieber drinnen lassen? Und wenn schon offen, die Zahnräder durch welche aus Metall ersetzen?
Die ausgleichswelle würde ich drin lassen und die Zahnräder sind bestimmt auch aus Gewichtsgründen aus Kunststoff. Gibt es die denn aus Metall?
@@bikedogtor1663 jap, ich meine ich hab die schon gesehen aus Metall. Aber das thema hat sich geklärt, die Maschine ist schon wieder verkauft
Servus, super Video. Hast du Adressen, von wo ich noch Teile beziehen kann für Rs
Hi, vielen Dank. Ich habe in ganz verschiedenen shops bestellt. Die normlager zb bei einem Lieferant für Lager. Die genauen shops habe ich nicht mehr im Kopf.
Hey there. Great video! Where did you get the engine manual?
Thank you! I got it with the bike
Where can i find that manual?
Great video
Thank you.
Umm I got it with the bike, google maybe?
Hallo, könntest du mir Bitte den link schicken von wo du alle teile hast also Lager und Dichtungen Usw
Sry das ist schon zu lange her. Google mal, die meisten Größen findet man in foren etc.
Can you leave links for all parts :)
For kit
No sry
@@bikedogtor1663 Np I found it
Hi
I found a RS 125cc 1997 cheap, how much cost you only the parts?
And the cylinder job?
Cylinder honing with some engine parts was around 250 and overall parts were around 600€
@@bikedogtor1663
Thank you very much for you answer 🙂
how did you change the bearing in the gear shift drum? the inner one
I didn't change it
@@bikedogtor1663 i broke the whole thing trying to get it out… new one on the way
@@sputniken4350 I had 2 and just chose the better one bc no idea how to replace it. I think it is a "lifetime" bearing once pressed in no way out.
Hey, i am so thankul you did that video hahah could you please tell me what the manual is called? So that i will find it when searching on google.
Glad the video helps you. Its called a service manual
Hallo, hat die RS 125 auch einen Ölfilter?
Nein das Getriebe hat keinen Ölfilter
where did you send the cylinder for nicasil plating because i should also🥴
I was lucky because plating wasn't necessary. In Germany mec-racing is the best address.
@@bikedogtor1663 thank you👍
where did you get that nm screwdriver
You mean the torque wrench? It's a "proxxon" tool you get it online.
Bist du bei dem 0,5 er geblieben ?
Ja
Servus woher hast du die Anleitung für das zusammenbauen
Das ist ein Werkstatthandbuch, kann man bestellen.
Danke dir 🙋♂️🙋♂️ bin gerade eine Aprilia Mx 125 am Restaurieren mit dem gleichen Rotax 122 Motor.
@@eliasdannenmaier3819 cool, viel Spaß beim schrauben
where you bought the pieces
Mostly from local stores. The bearings for example are standard sizes you get at every bearing store.
piston brand u using?
Whatever I get 👀
Hey can u help me how to get spare parts aprilia rx 125
Where are you from?
@@bikedogtor1663 Slovakia 🇸🇰
@@bikedogtor1663 its urgent, next week i go to race..
I only know where to buy in Germany so unfortunately I can't help
@@bikedogtor1663 can you send me webside
der motor ist halt einfach dafür gemacht neu aufgebaut zu werden.
hab vor kurzem nen minarelli am6 neu aufgebaut. das war der horror. du musstest da wirklich das Getriebe distanzieren
ps: du konntest doch dein lagerabzieher umbauen (also die krallen anders rum dran machen) um diese Lager von innen nach außen zu ziehen?
und einen nikasil zylinder neu auszuhohnen ohne diesen neu zu beschichten, gibt dem zylinder viel mehr laufleistung, da die queren rillen vom hohnen für einen bessern ölfilm sorgen
Moin, die zweitakter finde ich generell einfach zu überholen. Gewisse Eigenheiten hat ja jeder Motor. Die Abzieher zum einziehen mache ich ungern weil die Krallen schnell abrutschen und dann ist viel Kraft dahinter. Am besten wäre eine Presse.
8:37
Kanns sein, dass der dichtring falsch eingebaut wurde?
Im Manual steht: "Die Dichtlippe des Wellendichtrings muß nach außen zeigen. ..."
Nach außen, im Sinne von in Richtung Kupplungsseite. In dem Video, wo du den Motor zerlegt hast, sieht man, dass die Dichtlippe in Richtung kupplung zeigt... :)
Also ist ja ein Radialer Dichtring. Laut wikipedia ist die Flüssigkeitsseite immer in Richtung Dichtlippe
Ich werd den Motor in nächster Zeit mal genau unter die Lupe nehmen. Der hat viele Kleinigkeiten. Die Lager haben ein Loch im Gehäuse wo Gemisch durch laufen kann zum schmieren und kühlen. Oberhalb von diesem loch ist eine kante / Einsparung, was das Öl ins lock leitet. Sogesagt eine Öl Leitplanke 🧐😂
Die Dinger sind in manchen Motoren vermurkst und müssen zurecht gedremelt werden
@@Tiwey ja nach Anleitung habe ich den Ring falsch eingebaut. Aber Fakt ist auch dass die manuals immer Fehler beinhalten und ich montiere Wellendichtringe immer mit der Lippe zur Druckseite. So drückt der entstehende Druck (ja meistens Öl) die Lippe auf die Welle. Bei dem Zweitakter wird ja das Gemisch im kw Gehäuse vorverdichtet wodurch ein Druck auf der Innenseite entsteht. Federgabeln sind ein gutes Beispiel. Der Simmerring wird mit der Lippe Richtung Öl montiert weil er andersrum gar nicht dichten würde.
@@Tiwey das Loch was du meinst ist tatsächlich wichtig. Allerdings "kann" hier kein Gemisch durch fließen sondern bei jedem Hub wird das vorverdichtete Gemisch durch die Lager und dann die Löcher nach oben in den Brennraum geleitet. Das schmiert und kühlt die Lager.
@@bikedogtor1663 interessant. Also kann man den Ring auf beiden Seiten mit der lippe nach innen bauen? Man geht also Gefahr wenn man es falsch rum einbaut, dass die Verdichtung den Ring raus drückt?
What’s the price of all the total ?
Hi, the bike with all rebuild parts has cost around 1.000€. Or do you mean engine parts only?
ruclips.net/channel/UCdi1LZCp4b0ubT2CXGRh7-Q
Тем временем где-то в России ✋
call me jesus because I put the circlips in using my fingers
Jesus