Hi I recently bought the x6fg transmitter and receiver for my wltoys 144010 brushless, the throttle works fine but the servo doesn’t work at all. I’ve tried resetting the receiver but nothing seems to work. Any ideas? Thanks.
Make sure receiver is set up properly 1 to turn 2 to burn make sure there inserted the right way around. Also if you have pressed the internal button on receiver it changes functions
Steering trim is not for how fast your steering turns, it how far your steering turns. It's for setting your end link adjustment so you don't stress your servo by it straining to turn your wheels further than mechanically possible...
@@bigbeardrc4145 my transmitter says st/throttle trim. And epa steering and throttle… I thought dual rate isn’t the speed of turning it’s how much it can turn left to right ??
Hey man thank you so Much for this video, it helped me a lot. I have one question though, how can I make my Rc car move backward? I bought the same dumbo rc controller and used the included receiver but I still can’t get it to work.
Nice one! May I ask of it is possible to use the same transmitter with different cars/receivers and, if it is, how you can switch from one receiver/car to another one...?
Yes you can link as many receivers together as you want you just switch off the car your not using and switch in the other once bound to the transmitter you then just change the trims etc 😉
Salut j ai monté ce récepteur gyro sur ma voiture et beaucoup de problème de direction , le servo va uniquement a droite ,avec ou sans gyro , je ne comprends plus rien .
Is your steering trim backwards like mine? If it’s pulling left, I have to turn the knob to the left instead of to the right. And vice Versa. Not sure if I can correct that.
Depending on which way you set up your receiver you may have to reverse the gyro direction. Turn the receiver on and push the little button 2 times. The front wheels should turn in the opposite direction of the rear wheels if you have it set up correctly.
Do you know how to reverse the gyro action? Mine steers opposite the skid instead of into the skid. Thus my car spins out easier as I turn channel six up higher. Almost impossible to steer with gyro at full sensitivity.
My receiver is flashing blue always i turn on the remote? I tried to calibrate but still the light keeps on flashing in speed. The rc car behaves as if it is possessed by ghost. The receives signals from channels for turning on lights and for differential locks. But acceleration and brake doent respond… Steering wheel turns after 30 seconds of intial turning on remote. Does any one had a similar issue or can anyone suggest a solution?
Did you know that you can flip your rear A arms over which puts the shocks toward the front. Couple changes needed in terms of screws and spacers etc. It gives you a slightly longer and more stable wheelbase. It does however remove the capability of using droop screws so you have to infiltrate the shocks instead to lower the car.
I did know but I cant do that as I have the sway bar kit fitted and If you switch the arms around you cant mount them.i have done a mod video on the metal a arms I bet you could still utilise my mod on the flipped arms
Thank you very much this is the best video on RUclips explaining this dumborc ..u did a great job you can also do another one Maybe running the car and explaining ..
So I tried it when I set up my speed run car and it actually moves the tires by it self ..without me pressing trigger ..I'm also wondering if that's why it says keep on 0 the bottom I'm talking is the one to the upper right it has 123 on each side and o in the middle
@@bigbeardrc4145 yea I did that too but when it connects to the control the only thing that works is the servo and the motor keeps going at full speed I think I’m going to have to buy a new one 💀
3 years later you solved my issue!!, Subscibed...
Just ordered one with a hobywing 1060 brushed esc
I’ve finally got round to ordering this dumbo transmitter! Nice review on this BB also informative 👍🙏
Thanks dude they are great
I just subscribed.... John Robinson RC sent me nice channel 👍
Thank you
Hi I recently bought the x6fg transmitter and receiver for my wltoys 144010 brushless, the throttle works fine but the servo doesn’t work at all. I’ve tried resetting the receiver but nothing seems to work. Any ideas? Thanks.
Make sure receiver is set up properly
1 to turn 2 to burn make sure there inserted the right way around. Also if you have pressed the internal button on receiver it changes functions
Yeah I put the servo on channel 1 and esc on channel 2
Oh I did not know that, maybe I’ll try and press it again to reset it back to original function. 🤷♂️
Thanks btw 🙏
Finally I got it, I just flipped the servo wire the other way. Thanks 🙏
Really really nice video Thx!
Steering trim is not for how fast your steering turns, it how far your steering turns. It's for setting your end link adjustment so you don't stress your servo by it straining to turn your wheels further than mechanically possible...
Steering trim is for setting the car going straight steering dr is speed of steering
@bigbeardrc4145 not what I was talking about, the lower knob on the st side 0-100 setting is not how fast your wheels steer, its how far
Would channel 3 and 4 be used for a cooling fan for both?
Yes you can use 3 or 4 for fans or leds etc
@@bigbeardrc4145 does this transmitter have dual rate?
@@Sam-nz2zs yes it does buddy for steering and throttle
@@bigbeardrc4145 my transmitter says st/throttle trim. And epa steering and throttle… I thought dual rate isn’t the speed of turning it’s how much it can turn left to right ??
Hey man thank you so Much for this video, it helped me a lot. I have one question though, how can I make my Rc car move backward? I bought the same dumbo rc controller and used the included receiver but I still can’t get it to work.
Have you set it up with the esc properly,what esc do you have
@@bigbeardrc4145 the esc that I have is DUMBORC X6FG
Thats the receiver and transmitter mate have you changed the esc and motor aswell
If not that's why it won't work as it can't be used with the stock electronics
@@bigbeardrc4145 Ohhh, ok. Do I have to change them? I haven’t changed the motor or esc
They are great controllers.
Great video with good information. Thx for sharing. Big like & new subscriber here
Nice one! May I ask of it is possible to use the same transmitter with different cars/receivers and, if it is, how you can switch from one receiver/car to another one...?
Yes you can link as many receivers together as you want you just switch off the car your not using and switch in the other once bound to the transmitter you then just change the trims etc 😉
@@bigbeardrc4145 Thanks!
I’ve been debating on getting one of these radios to try.
I love mine you wont be disappointed
Salut j ai monté ce récepteur gyro sur ma voiture et beaucoup de problème de direction , le servo va uniquement a droite ,avec ou sans gyro , je ne comprends plus rien .
How do u adjust steering end points with it
In the manual there is a part on end points I personally haven't used it
@@bigbeardrc4145
I just got one for blx granite and
Steering end points are a lot less with it. It does perform 10x better then tactic one
@@stevegivelas9769 you use the esc to do end points
@@bigbeardrc4145
Yes but tactic had buttons to push to add more steering dumbo has it to on top of contrôlée it is at 100% but steering seems less
Thx for the Video 😎 Lg Max
Where can I find that phone holder? Great video. 👍
It's just the end of a selfie stick I have a how to video on my channel
Is your steering trim backwards like mine? If it’s pulling left, I have to turn the knob to the left instead of to the right. And vice Versa. Not sure if I can correct that.
I've not noticed I'll gave to check now
I have the same Issue. Turning the steering servo 180 degrees would solve that problem, unfortunately the Kraton steering setup doesn't allow that.
Depending on which way you set up your receiver you may have to reverse the gyro direction. Turn the receiver on and push the little button 2 times. The front wheels should turn in the opposite direction of the rear wheels if you have it set up correctly.
💯🤟🏻🤠
what can i use the USB port for?
Its used to charge rechargeable batterys
Do you know how to reverse the gyro action? Mine steers opposite the skid instead of into the skid. Thus my car spins out easier as I turn channel six up higher. Almost impossible to steer with gyro at full sensitivity.
Have you tried spinning the gyro 180 degrees i have mine with the writing reading the right way from the rear of the car
@@bigbeardrc4145 Thanks for the reply. Found the answer. with gyro active, push button on receiver 2 times to reverse action.
Noob here 🙋 so this can be used with brushed setup?
Yes buddy
My receiver is flashing blue always i turn on the remote? I tried to calibrate but still the light keeps on flashing in speed. The rc car behaves as if it is possessed by ghost. The receives signals from channels for turning on lights and for differential locks. But acceleration and brake doent respond… Steering wheel turns after 30 seconds of intial turning on remote.
Does any one had a similar issue or can anyone suggest a solution?
Wow that is weird. Have you checked all are plugged in correct ? And in the manual there is a way to manufacture reset the tx
Did you know that you can flip your rear A arms over which puts the shocks toward the front. Couple changes needed in terms of screws and spacers etc. It gives you a slightly longer and more stable wheelbase. It does however remove the capability of using droop screws so you have to infiltrate the shocks instead to lower the car.
I did know but I cant do that as I have the sway bar kit fitted and If you switch the arms around you cant mount them.i have done a mod video on the metal a arms I bet you could still utilise my mod on the flipped arms
@@bigbeardrc4145 Cool cheers I'll check out the video
5:04 min can u explain a little better what that does throttle trim
It allows you to make small adjustments to the steering to get the car running straight
Thank you very much this is the best video on RUclips explaining this dumborc ..u did a great job you can also do another one Maybe running the car and explaining ..
So I tried it when I set up my speed run car and it actually moves the tires by it self ..without me pressing trigger ..I'm also wondering if that's why it says keep on 0 the bottom I'm talking is the one to the upper right it has 123 on each side and o in the middle
I think my controller is broken cause it speeds up by just connecting the battery and while the control is off
You should always turn on your controller first,I've had that issue using cheap escs
@@bigbeardrc4145 yea I did that too but when it connects to the control the only thing that works is the servo and the motor keeps going at full speed I think I’m going to have to buy a new one 💀
@@delwyn_rc3318 have you made sure that the trim is zeroed and have you set the end points on the esc
Your gyro is working the wrong way, it's inverted.
It was only on for demo purposes its been switched around now thanks for watching though
@@bigbeardrc4145 all good. I just notice details like that :)
*To
But where is the button in the hole
The bind button on the receiver ??
I dont have any pressable buttons in the hole. So i cant get the gyro to work
@@romula8 if you have a x6f you won't have a gyro only the x6fg has a gyro