@hash include electronics I've replaced the baterry with a one that has more amperage, and now the project is fully functional it works, thank you and i wish you all the best and good health!! 👍
Please tell me if I use 9v HW Battery then it will work? Also tell how much power will use to run the car. I power is not sufficient then I will use 2 HW battery of 7v . It will not affect my motor driver na because 14v power is there. Please tell me.
@hashincludeelectronics I'm facing a issue while uploading the code "I2Cdev.h and other libraries not being found" what should I do I did download all the files
@@SR_gupta5521 please make sure to buy the products which are used in the project and shown in video to avoid issues. Probably You can return the wrong product you bought from wherever if possible . 👍🏻👏🏻
Its just not working for me it says all things in serial monitor all wires are correct both code are in but the it just says antializing I2C devices... Testing device connections... MPU6050 connection failed Send any character to begin DMP programming and demos Initializing DMP... Then it fails i have tried resetting it alot of times and the value of the module which tells its position is also not showing
I am using arduino on both Transmiteer and receiver side i used 3.7 voltage battery ( 3 batterys) im getting 11.8 v by it and i connected it to motor driver and all connections properly the car is moving in circles when i disconnected battery from Transmiteer then also it is moving in circles
Bro my car is working properly when I connect it to my laptop and pass the demo value in serial monitor but not working when battery is connected what should I do
hello, I did exactly what you did, but when I upload the codes nothing happens, I don't even hear the sound of the microcontrollers operating, do you have an idea for the origin of the problem?
great tutorial, much thanks! I have a question, I have combined everything followed the video, however, I have found that the car can run directly without the transmitter part power on, and just run straightly, how to solve that problem?
@@hashincludeelectronics I have the same problem, what's the issue? I have checked all the wiring and everything is correct. Pls help me to solve this problem. With receiver car motors react, but only make sounds, but without receiver car just run forward. I use rechargable battaries 7,2 V
Great tutorial as always. I have a question. If I use a chassis with only two motors do I have to modify the code? I would appreciate your help, if you can tell me which part has to be modified. Thanks.
Guys I found that people are facing issues with car mostly because they are using those 9v non rechargeable battery . These batteries do not provide enough current for motors to rotate . So I would suggest to use good rechargeable batteries . Or if you are planning to still use 9v battery then use 3-4 such batteries in parallel together. Cheers 👍🏻
@@TheGuy47YT I generally use LIPO batteries and also I have shared links to it in some of the projects . Will check and share in this project as well .
I am trying to build it with Arduino UNO and the transmitter code doesn't seem to work, the code compiles without any problem but in the serial monitor it's showing "MPU6050 connection failed Send any character to begin IMP programming and demo:" Please help
brother while uploading the code of transmiteer i am getting the error :- Arduino: 1.8.19 (Windows 10), Board: "Arduino Nano, ATmega328P" Sketch uses 17392 bytes (56%) of program storage space. Maximum is 30720 bytes. Global variables use 611 bytes (29%) of dynamic memory, leaving 1437 bytes for local variables. Maximum is 2048 bytes. Serial port not selected.
Hi sir, I've done ur project, I've given connections correctly and completed programming too. But it is not working, i thought is there any problem in mpu6050, so I checked the accelerometer with serial monitor using Arduino but at all the three axis it is showing the value 127 continuously what could be the problem pls tell me sir.........
@@hashincludeelectronics ok sir thank you so much, but I checked the mpu6050 in serial monitor using Arduino, in that the axis values are not changing it continuously showing the constant value 127 in all the position, so I bought a new one and checked the sensor in serial monitor, in that for the first 5 minutes it was showing the correct axis values and after sometime I faced the same problem in this sensor too........ What could be the problem sir
bro in my transmitter when i connect the +5v volt pin to the power rail the light dosent glow i n the arduino but when i remove it it starts glowing and also the car is not moving
Please check the circuit diagram. Also watch the video carefully and slowly to avoid any mistake in connection . 👍🏻 don’t worry it will work as it worked for me 👏🏻
my Nrf 24l01 is not giving any singnal to the car plss help ive used nrf adapter and rechargable batteries and also ive checked serial monitor its shows nothing plss help
Let me ask, I installed and have all the libraries but my circuit only lights up and doesn't work like the video tutorial, what should I do? Please help me.
Hey i connected the components as per the diagram and it doest work , i am using recharble 7.4 volt batteries and i dont seem to have any faulty parts. The motor arent moving at all , i feel like nrf24l01 arent connected ? Can you think of a probled , also i am using only one 9v battery for the transmitter
Please don’t use that 9v non rechargeable battery . It causes issues related to power . Use only rechargeable battery at both transmitter and receiver 👍🏻👏🏻
hi i got this error on the transmiter : Send any character to begin DMP programming and demo: Initializing I2C devices... Testing device connections... MPU6050 connection failed
when I copy folders I2CDEV and MPU6050 and paste them to library in arduino in document, then I sketch your code, it is error : "error compiling for board arduino nano". But if I dont copy and paste them, just sketch your code, it is done compiling. So what is the problem?
@@hashincludeelectronics yes bot now I have another problem, on reciver i used nano and on transmitter uno, and now I switch but dont work , and I go back how it was and now the reciver dont work its say compiled and not showing the debug
In my motor driver module Input is going and red light also turning on but at power is not coming at output side Everything else works fine Please give me solution...
Hey I connected the transmitter to breadboard, the pwr and L light up, is the tx and RX supposed to light up too? How do I know if the transmitter is working without the receiver?
Hey I have assembled complete like you have done but still it doesn't work I have used work lithium ion cells for car and one for transmitter but it still won't work.any solutions what can be the problem
i have checked my circuit alot of times its exactly the same, am using 3s lion batteries for reciever and 2s for transmitter still no movement Could you please help me?
hi sir, i did every thing in the video but the car is not moving, i ordered nrf24101 only with out the +, is it okay or it should be the nrf24101+ , please answer me
If i wanna use a 9V battery, I need to do some change or it’s good ? And if I want to buy 3.7 V lithium batteries, how many do you have? Please i need for my final project
hello sir, I am a 12 year old kid and I made this project successfully. but after like 10 months later, the Arduino Nano is getting really hot, it is dangerous at it metled my table cloth. how do I fix it?
tthe nrf adaptor is not glowing when connected to a power source, rest all are working perfectly, i have checked all the connections and they all are working just the nrf adaptor is not working.
Hey mate I wanna know first we will connect transmittor Arduino to the laptop and paste the code and then upload and verify both? And later on we will connect receiver and paste the code and do the same thing? After that just give power to the batteries and will it work directly?and which battery to use for receiver?
bro still my car is not running even my connection are fine and I have checked the values in serial monitor ,transmitter and receiver both are showing correct value and I am using two 3.7 li-ion battery with two motors ,bro your help will be appreciable
Please tell me 9v HW battery is enough for motor driver to run the car. It's very urgent please understand my feelings. Please reply me fast. Please Please🙏🙏🙏🙏🙏🙏🙏.
hey dude, when I try to insert nrf module on the nrf adaptor it turns off, but then why I remove it, it turns back on. This is happening to both the transmitter and the car reciever. I m doing the hand gesture controlled car using nrf24l01+ and mupu6050 and using 9V batteries.
I need to ask that how much time does it take to upload the code on transmitter. Because my system is just showing me uploading from last 20 mins. Please Help me in this.
This is little bit complex project so needs lot of attention and patience. Please check the video again for any missing step. Check for loose connections . Use rechargeable battery . 👍🏻👏🏻
ive done everything perfectly and uploded the code but i cannot see the output like no motion and transmitter isnt pairing with car how to solve this? plss help me out of this?
Thanks for checking out the video 👍🏻 Did you follow the steps which I mentioned in video ? We don’t need to install entire zip file . Just copy the required libraries as suggested in video .
@@hashincludeelectronics Sorry didn't notice. Uploaded successfully. Now the issue is with mpu i think i've uncommented the print debug but its showing testing dpu 6050 initializing failed
@@adarshraj1211 what is not working? If you enable the print debug then you have to enter the input from serial monitor . Why are you uncommenting the print debug ?
@@hashincludeelectronics Sir my port is not deducting the Usb when i am installed the driver of that and then tried the port was not coming then also pls help
hello sir i want to do this project on an actual wheelchair, can i use the same componenets as above apart from battery and motor or do i need to purchase different components, please guide me
Yes you will have to purchase different motors and motor driver which will support wheel chair movement load . You need to do some research on this 👍🏻👏🏻
Hi bro thanks for your help in my project. And I have an doubt that what type of jumper wire should we buy 10+10+10 or 20+20+20or others Plss reply bro
sir, my car is not moving at all. I have double checked the connections and used a 9V nut bolt battery for transmitter and 3 rechargeable 186500 3.7V li-ion battery for receiver and uploaded your codes directly. There was no error while uploading codes. Lights of every components is on but the car is not moving at all. Can you please help me ?
If you know how to print values on serial monitor then you can print the values received at receiver end to confirm the communication is ok . Also double check your connections . Don’t worry it will work 👍🏻
In TRANSMITER u take ( +5) ,( GND ) form Arduino to breadboard power rail but in TRANSMITER diagram there was different U TAKE ( GND ) and ( VIN ) to the Power or battery . please tell me which is correct ? Please
Vin and gnd is used to provide power to Arduino . And then from 5v and gnd from Arduino , we are providing power to other components. Hope this makes clear .
Please tell me if I use ADXL 345 Gyro than it will work or some changes in code.
@hash include electronics I've replaced the baterry with a one that has more amperage, and now the project is fully functional it works, thank you and i wish you all the best and good health!! 👍
This is awesome news . Well done and thanks 👍
how much amperage battery bro......How many battery you used bro
Can you please guide me I am facing some problem please reply I am so tence.😢
Please tell me if I use 9v HW Battery then it will work?
Also tell how much power will use to run the car. I power is not sufficient then I will use 2 HW battery of 7v .
It will not affect my motor driver na because 14v power is there.
Please tell me.
More than 12 V is not recommended.
@hashincludeelectronics I'm facing a issue while uploading the code "I2Cdev.h and other libraries not being found" what should I do I did download all the files
Can you help me install that file
Please fast reply it's very argent. In hurry I was purchase ADXL345 not MPU6050. So please tell me there won't be any problem. 🙏🙏🙏🙏 Please.
Please use mpu6050 only 👏🏻👍🏻
OK, Thank you for your answering👍. I waste my money@@hashincludeelectronics
@@SR_gupta5521 please make sure to buy the products which are used in the project and shown in video to avoid issues. Probably You can return the wrong product you bought from wherever if possible . 👍🏻👏🏻
Its just not working for me it says all things in serial monitor all wires are correct both code are in but the it just says
antializing I2C devices...
Testing device connections...
MPU6050 connection failed
Send any character to begin DMP programming and demos
Initializing DMP...
Then it fails i have tried resetting it alot of times and the value of the module which tells its position is also not showing
Try using another mpu6050 module 👍🏻👏🏻
And btw I am using Nrf24Lo1
I am using arduino on both Transmiteer and receiver side i used 3.7 voltage battery ( 3 batterys) im getting 11.8 v by it and i connected it to motor driver and all connections properly the car is moving in circles when i disconnected battery from Transmiteer then also it is moving in circles
May be there is a loose connection. Please check again 👍🏻👏🏻
Hi sir, it is just showing uploading and it is showing error what should i do😢but coding ia right
Try changing USB cable . Try to connect to different usb port . 👍🏻👏🏻
Bro my car is working properly when I connect it to my laptop and pass the demo value in serial monitor but not working when battery is connected what should I do
I have replied on other comment .
hello, I did exactly what you did, but when I upload the codes nothing happens, I don't even hear the sound of the microcontrollers operating, do you have an idea for the origin of the problem?
Please try changing mpu6050 👏🏻👍🏻
Hello
This problem happened to my project too Did you solve it?please tell me fast
Nrf not communating@@user-el7mj2dk6k
@@hashincludeelectronics same problem
great tutorial, much thanks! I have a question, I have combined everything followed the video, however, I have found that the car can run directly without the transmitter part power on, and just run straightly, how to solve that problem?
Please check the video for any missing steps . Also make sure you use only rechargeable battery 👏🏻👍🏻
@@hashincludeelectronics I have the same problem, what's the issue? I have checked all the wiring and everything is correct. Pls help me to solve this problem. With receiver car motors react, but only make sounds, but without receiver car just run forward. I use rechargable battaries 7,2 V
Bro can we use 18650 batter for both transmitter and receiver module
Yes you can 👍🏻👏🏻
Great tutorial as always. I have a question. If I use a chassis with only two motors do I have to modify the code? I would appreciate your help, if you can tell me which part has to be modified. Thanks.
Thank you very much for checking out the video 👏🏻👍🏻. It will also work with 2 motors . No change in code .
@@hashincludeelectronics Thanks a lot!
Working perfectly Sir!
@@hashincludeelectronics can i use 18650 li on battery instead of these battery?? Or 9 v battery
@@techwith_Aamir yes you can that lion battery . Don’t use 9v non rechargeable battery👍🏻👏🏻
i uploaded the code and both the transmitter and reciever arduino are lighting uo but when i move the transmitter the motor does not move
Please check the video for any missing step 👍🏻👏🏻
Guys I found that people are facing issues with car mostly because they are using those 9v non rechargeable battery . These batteries do not provide enough current for motors to rotate . So I would suggest to use good rechargeable batteries . Or if you are planning to still use 9v battery then use 3-4 such batteries in parallel together. Cheers 👍🏻
^^ this message has saved my life THANKS a lott
It will be nice if you suggest us some GOOD RECHARGABLE BATTERIES which will be perfect for this project (please share an amazon link)
@@TheGuy47YT good to hear that 👍🏻
@@TheGuy47YT I generally use LIPO batteries and also I have shared links to it in some of the projects . Will check and share in this project as well .
How much amp is required bro
I am trying to build it with Arduino UNO and the transmitter code doesn't seem to work, the code compiles without any problem but in the serial monitor it's showing
"MPU6050 connection failed
Send any character to begin IMP programming and demo:"
Please help
Please check the connections again . Looks like some loose connection issue or incorrect connection. 👍🏻👏🏻
@@hashincludeelectronics I replaced the sensor and it worked thankyou
@@hashincludeelectronics but now the receiver works for a second then it stops receiving data
@@srujanendhratalla4187 do you use rechargeable battery ? If not then please use it . It avoids most of the power related issues .
@@hashincludeelectronics I'm using 3 18650 batteries in series which gives around 11.1 volts output
brother while uploading the code of transmiteer i am getting the error :-
Arduino: 1.8.19 (Windows 10), Board: "Arduino Nano, ATmega328P"
Sketch uses 17392 bytes (56%) of program storage space. Maximum is 30720 bytes.
Global variables use 611 bytes (29%) of dynamic memory, leaving 1437 bytes for local variables. Maximum is 2048 bytes.
Serial port not selected.
Select the port in Arduino IDE before uploading the code
Same problem
And I select the port
The solution is set the bootloader to Atmega 328p old loader
I select t’he port
Thanks bro for guiding me .first I make this project but it not work but when I change the battery it work 💯👍🏻👍🏻
Nice to hear that it worked. Good Job 👍
Bro can you help me🙏🙏🙏
How much volt you used in transmitter side bro
Does 9v battery work in the transmitter???
How much volt battery is needed????
Sir plss reply
Hi sir, I've done ur project, I've given connections correctly and completed programming too. But it is not working, i thought is there any problem in mpu6050, so I checked the accelerometer with serial monitor using Arduino but at all the three axis it is showing the value 127 continuously what could be the problem pls tell me sir.........
It means the transmitter is not sending data . Check for loose connections. 👍🏻👏🏻
same problem bro no losse connections
@@hashincludeelectronics
@@hashincludeelectronics ok sir thank you so much, but I checked the mpu6050 in serial monitor using Arduino, in that the axis values are not changing it continuously showing the constant value 127 in all the position, so I bought a new one and checked the sensor in serial monitor, in that for the first 5 minutes it was showing the correct axis values and after sometime I faced the same problem in this sensor too........ What could be the problem sir
Reply sir pls
its completely fake doesnt worked at all, i have working since 1 year, its completely trashhhh.....
Sorry to hear that . However what exact error do you face ? It’s worked for us and will work for you too . Dont worry 👍🏻👏🏻
Sir I'm in a very big problem. my car is not moving only lights are glowing I've done every connection right what to do
in transmitter only arduino light is glowing
Please use rechargeable battery for proper power supply. Also make sure connections are correct and there are no loose connections.
sir how can I contact you plss tell
sir please reply fast
bro in my transmitter when i connect the +5v volt pin to the power rail the light dosent glow i n the arduino but when i remove it it starts glowing and also the car is not moving
Please check the circuit diagram. Also watch the video carefully and slowly to avoid any mistake in connection . 👍🏻 don’t worry it will work as it worked for me 👏🏻
my Nrf 24l01 is not giving any singnal to the car plss help ive used nrf adapter and rechargable batteries and also ive checked serial monitor its shows nothing plss help
Please check if there is any loose connection . That might cause issue .
if we use arduino uno instead of nano does it work same ??? or do we need some changes in code??
It works the same 👍🏻👏🏻
I need a head gesture controller for my wheelchair.
Please check if this project will be useful for you . It uses gesture controller 👏🏻👍🏻
Thanks for the idea i will use it for my final year project
Thanks for checking out the video and all the best for your project 👍🏻
hello 😭😭 help me im faceing issues in the Arduino folder . its showing its empty there is no Library folder in it sir please help me im frustrated
Please check the video slowly and carefully. All the steps are given there . Don’t rush 👍🏻👏🏻
Let me ask, I installed and have all the libraries but my circuit only lights up and doesn't work like the video tutorial, what should I do? Please help me.
Please double check your connections . Also take a look at video again slowly and carefully for any missing step 👍🏻👏🏻
Bro I gave 7.4 volt power supply for car does this cause the car not to move, because my car not moving
Does the car changes speed based on the angle of tilt of our hand..?
Yes it does 👍🏻👏🏻
in my serial monitor, im getting random charcters, can u help i tried everything?
You need to select correct baud rate 👍🏻👏🏻
My receiver side arduino is not working what can be the error nrf adapter is working but Arduino is not showing any light
Please check the connections again 👍🏻👏🏻
Hey i connected the components as per the diagram and it doest work , i am using recharble 7.4 volt batteries and i dont seem to have any faulty parts.
The motor arent moving at all , i feel like nrf24l01 arent connected ? Can you think of a probled , also i am using only one 9v battery for the transmitter
Please don’t use that 9v non rechargeable battery . It causes issues related to power . Use only rechargeable battery at both transmitter and receiver 👍🏻👏🏻
how did you copy mpu6050 and i2cdev at the same time?
Please check the video for the exact steps 👍🏻👏🏻
hi i got this error on the transmiter :
Send any character to begin DMP programming and demo:
Initializing I2C devices...
Testing device connections...
MPU6050 connection failed
There is loose connection. Please check . 👍🏻👏🏻
I m facing an error.. my transmitter and receiver didnt collaborate with each other..... Pls if you can help so help me
Please make sure you are using rechargeable battery only . Also check the video slowly and carefully for any missing step 👍🏻
when I copy folders I2CDEV and MPU6050 and paste them to library in arduino in document, then I sketch your code, it is error : "error compiling for board arduino nano". But if I dont copy and paste them, just sketch your code, it is done compiling. So what is the problem?
What error do you get ? Could you send me full error ? May be connect with me on Instagram hashincludeelectronics
Bro in the code it is showing Port com3 not supported and com4 access denied which port I have to select now plss tell
Does it show any other port ? Use the other ports which are shown . There should one port allotted when you connect Arduino to laptop .
hi i have a problem, i did evrithing u do, and the car works only when its connected on pc and see on serial monitor the values plz help
Please use rechargeable battery for car and transmitter 👍🏻👏🏻
@@hashincludeelectronics yes bot now I have another problem, on reciver i used nano and on transmitter uno, and now I switch but dont work , and I go back how it was and now the reciver dont work its say compiled and not showing the debug
shoul i buy xt 60 male or female connector
If your lipo battery has male connector then buy female connector. Or vice a versa 👍🏻👏🏻
Follow all steps but not working some time only 2 wheels start when press to nrf adapter of car
Please use rechargeable battery 👍🏻👏🏻
Hello. In what software did you made the circuit diagram? I tried in wowki but i can't find the nrf24l01 module. Neither in thinkercad. Kind regards!
I use fritzing . Sometimes parts are not available so I use images and make circuit diagram 👍🏻👏🏻
In my motor driver module Input is going and red light also turning on but at power is not coming at output side
Everything else works fine
Please give me solution...
Make sure you are using only rechargeable battery 👏🏻
@@hashincludeelectronics I'm using LiOn battery
Still not working
can i use
nrf24l01 wireless module the one without the antena?
Hey I connected the transmitter to breadboard, the pwr and L light up, is the tx and RX supposed to light up too? How do I know if the transmitter is working without the receiver?
You need to connect receiver to see if you are receiving data correctly . 👍🏻👏🏻
Hey I have assembled complete like you have done but still it doesn't work I have used work lithium ion cells for car and one for transmitter but it still won't work.any solutions what can be the problem
Check for any loose connections. Also make sure you are using nrf adapter 👍🏻👏🏻
i have checked my circuit alot of times its exactly the same, am using 3s lion batteries for reciever and 2s for transmitter still no movement
Could you please help me?
And whenever I connect my transmitter to the lptp to upload the code my laptop suddenly shuts off. When I connect it to the charger, it then works.
May be your mpu6050 is faulty . Do you have another one ? Try using that 👍🏻👏🏻
hi sir, i did every thing in the video but the car is not moving, i ordered nrf24101 only with out the +, is it okay or it should be the nrf24101+ , please answer me
I would suggest to use nrf+ with adapter 👌🏻👍🏻
If i wanna use a 9V battery, I need to do some change or it’s good ? And if I want to buy 3.7 V lithium batteries, how many do you have? Please i need for my final project
Yes you can use 9v battery however make sure it’s rechargeable only . You can use 2 3.7 volts cells 👍🏻👏🏻
@@hashincludeelectronics How much amperage do you recommend for 9v batteries?
@@diogomane5359 2 A 👏🏻👍🏻
Hello, if I use a 7.4V 800mah 20c 1s battery in this project, will there be any problems in the project? Can you please be quick?
It will work 👍🏻👏🏻
Sir can we solder the wires instead of breadbodding
Yes 👍🏻👏🏻
hello sir, I am a 12 year old kid and I made this project successfully. but after like 10 months later, the Arduino Nano is getting really hot, it is dangerous at it metled my table cloth. how do I fix it?
May be that nano is faulty . Use the new one 👍🏻👏🏻
the transmitter is not working. ive checked all the connections, rechargable batteries etc etc. can you find me a solution
?
What issue are you facing ?
The signals are not working as intended, even the mpu6050 module is working
tthe nrf adaptor is not glowing when connected to a power source, rest all are working perfectly, i have checked all the connections and they all are working just the nrf adaptor is not working.
Please check for the connections again 👍🏻👏🏻
Hey mate I wanna know first we will connect transmittor Arduino to the laptop and paste the code and then upload and verify both?
And later on we will connect receiver and paste the code and do the same thing?
After that just give power to the batteries and will it work directly?and which battery to use for receiver?
Yes exactly 👍🏻👏🏻
bro still my car is not running even my connection are fine and I have checked the values in serial monitor ,transmitter and receiver both are showing correct value and I am using two 3.7 li-ion battery with two motors ,bro your help will be appreciable
Check if 5v is properly connected to Arduino . Also make sure your batteries are fully charged .
Please tell me 9v HW battery is enough for motor driver to run the car. It's very urgent please understand my feelings.
Please reply me fast. Please Please🙏🙏🙏🙏🙏🙏🙏.
If it’s rechargeable then we are ok 👍🏻👏🏻
hello again sir, to power the nrf adapter do we need to connect the 2 jumpers (in l298n) to +5V and GND or both only in +5V
It should be +5v and GND.
I've done all the connections and
But not getting the output
I've have not used the adapter
Yes please use the adapter . Also make sure to use only rechargeable battery 👍🏻
You've given 2 codes for receiver, which one to upload?
hey dude, when I try to insert nrf module on the nrf adaptor it turns off, but then why I remove it, it turns back on. This is happening to both the transmitter and the car reciever. I m doing the hand gesture controlled car using nrf24l01+ and mupu6050 and using 9V batteries.
Don't use 9 v battery
Please use rechargeable battery only 👍🏻👏🏻
I need to ask that how much time does it take to upload the code on transmitter. Because my system is just showing me uploading from last 20 mins. Please Help me in this.
It should be quick . Not more than 1-2 minutes 👍🏻👏🏻
what to do when nrf module is not responsive and it seems like it chooses an environment where it transmits and receives signal easily
Bro why you didn't attach the transreciver in the transmitter
What do you mean ? I did not get your question properly .
in the receiver you attached the transceiver of nrf24l01 but in transmitted you didn't attach it
and one more thing can we use big breadboard or we have to break it into two parts
@@kleb3154 ok you are taking about antenna ? If yes then you can attach antenna at transmitter as well . No issues 👍🏻
I know I'm asking excessive questions but do we have to copy down the code as it is or we have to make changes
another question is it mandatory for the batteries to be rechargeable? can non-rechargeable just not work?
Yes please use only rechargeable battery 👍🏻👏🏻
Hello, are nrf24l01 transceiver module and Receiver modul same thing. Like can u buy two nrf24l01 module and both can work for sender and reciver??
Yes exactly 👍🏻👏🏻
The device is not working even though the codes in transmitter and receiver is in. is there some kind of trigger to make this work?
This is little bit complex project so needs lot of attention and patience. Please check the video again for any missing step. Check for loose connections . Use rechargeable battery . 👍🏻👏🏻
Bro I tried to upload the code to Arduino nano but it's not uploading till 30mins
Please select proper board while uploading the code . Retry 👍🏻👏🏻
please tell what to do if not calibrating
how to find out that if it is male or female
Please check the description of your battery . Also check on internet for more details 👍🏻👏🏻
@@hashincludeelectronics bro it says JST-XH
Codes uploaded and circuit and model fixedd car is still not working could you please tell wat could be wrong
bro does transmitter needs rechargable battery or not
plss tell
pls reply fastttttt
Yes .
Oh then 2 jumper wires for the battery must only go to the 12V socket? Sorry if I am troubling you
No worries . I would suggest to check the video and connection diagram to avoid any confusion . It’s clearly mentioned in it. 👏🏻👍🏻
ive done everything perfectly and uploded the code but i cannot see the output like no motion and transmitter isnt pairing with car how to solve this?
plss help me out of this?
1.Please make sure you use rechargeable battery . 2. Check the connections again . 👍🏻
Hey the I2C library is not getting installed saying the zip file does not contain a valid library
Thanks for checking out the video 👍🏻 Did you follow the steps which I mentioned in video ? We don’t need to install entire zip file . Just copy the required libraries as suggested in video .
@@hashincludeelectronics Sorry didn't notice. Uploaded successfully. Now the issue is with mpu i think i've uncommented the print debug but its showing testing dpu 6050 initializing failed
@@adarshraj1211 Good to hear that issue with library installation solved 👍🏻
@@hashincludeelectronics i've changed the mpu and checked the new one it is working but the issue is same. Help please.
@@adarshraj1211 what is not working? If you enable the print debug then you have to enter the input from serial monitor . Why are you uncommenting the print debug ?
what amperage is required for the TRANSMITER because i am using 3 li-on battery for reciver
That should be sufficient 👏🏻
Can i use 7-12 V 2s batteries for both transmitter and receiver?
Yes you can 👍🏻
Hello, is it okay to use 2s li-po batt in receiver?
Yes you can use that 👏🏻👍🏻
What is the approx cost of the whole project?? Can anyone please break it down
Please someone help here 👍🏻👏🏻
can i use NRF24L01+PA+LNA WITH ANTEENA(1100M) isntead of nrf24l01+ module?
If module is same then yes you can use it 👍🏻👏🏻
Hello Sir, there is some problem in the transmitter code I can't understand why it is 🤔🤔Pls tell
What exact problem are you facing ?
@@hashincludeelectronics Sir my port is not deducting the Usb when i am installed the driver of that and then tried the port was not coming then also pls help
which code is that bro? cant find it out from where you took that code
Code and diagram link is provided in the description of the video 👍🏻👏🏻
so if we directly copy ur code from description, we dont need to install rf24 library right?
You need to install that library 👏🏻👍🏻
Bro is it fine if we can use recheargable lithium battery cus I'm not able to purchase lipo battery in my country? Pls reply
@@GAMINGNJ10 yes you can 👏🏻👍🏻
@@hashincludeelectronics we can use the same pipe out address used in your code right?
@@GAMINGNJ10 yes 👍🏻👏🏻
And I am using lithium ion cells will it works?
Yes it will work 👍🏻👏🏻
Plzzzzz help 🔴‼️ Mpu6050 led is not glowing I have checked all the connection which is right Had I burned the mpu6050 or something
Yes it’s probably burnt . Try to just provide 5v and gnd to it and see . If led is still not glowing then it’s gone .
should i take 11.1v or 7.4 for transmitter
Better to take 7.4 👍🏻👏🏻
Which programmer , processor should we select
It should be Arduino nano . You can also take a look at video for this step 👏🏻👍🏻
hello sir i want to do this project on an actual wheelchair, can i use the same componenets as above apart from battery and motor or do i need to purchase different components, please guide me
Yes you will have to purchase different motors and motor driver which will support wheel chair movement load . You need to do some research on this 👍🏻👏🏻
Hi bro thanks for your help in my project. And I have an doubt that what type of jumper wire should we buy 10+10+10 or 20+20+20or others
Plss reply bro
You can buy mix of 10 and 20 👍🏻👏🏻
Hey everything is connected all lights are lit but it is not working
Please check the video for more details 👍🏻👏🏻
hey, can i use L293D driver module from electrobot instead of L298N?
No . You need to use only L298N driver only for this project 👏🏻👍🏻
Wow... Good one bro 👍 Keep Going ✌️
Thank you so much 😀
rf24 module is not working...is it bcz i dont have the adapter?
Yes please use adapter to avoid issues . Also use only rechargeable batteries 👍🏻
sir, my car is not moving at all. I have double checked the connections and used a 9V nut bolt battery for transmitter and 3 rechargeable 186500 3.7V li-ion battery for receiver and uploaded your codes directly. There was no error while uploading codes. Lights of every components is on but the car is not moving at all. Can you please help me ?
If you know how to print values on serial monitor then you can print the values received at receiver end to confirm the communication is ok . Also double check your connections . Don’t worry it will work 👍🏻
How can I do that? Can you please help me? Thanks in advance.
I have uncommented the line in sketch as you said so. But nothing appears on the serial monitor.
I can use Arduino Uno instead of Arduino Nano
Please tell me
Yes you can use that . It will work the same way 👍🏻👏🏻
Do I need to convert 5v to 3.3v for nrf24???
No .
In TRANSMITER u take ( +5) ,( GND ) form Arduino to breadboard power rail but in TRANSMITER diagram there was different U TAKE ( GND ) and ( VIN ) to the Power or battery . please tell me which is correct ? Please
Vin and gnd is used to provide power to Arduino . And then from 5v and gnd from Arduino , we are providing power to other components. Hope this makes clear .
Ok
Hey brother the Arduino is taking too long to upload the code doing it from 3-4 hrs continuously please reply if possible!!?
It should not take that long . Please check the connections to laptop .