Drive Shaft and Pinion Seal Replacement | 1994 Chevy K1500
HTML-код
- Опубликовано: 7 сен 2024
- In this video, I remove the rear drive shaft, yoke, and pinion seal on my '94 Chevy K1500 Silverado truck. I replace the pinion seal, and I also install a new driveshaft. I will have a follow up "Part 2" where I will replace the front seal (transfer case output seal) and I will also be installing the correct driveshaft, since the one in this video is the incorrect size.
Dorman 946050 Drive Shaft (Amazon will say this doesn't fit, but I can confirm it fits a 1994 K1500 Extended Cab with 141.5" wheel base)
amzn.to/3OVFtfx
Pinion Seal (Timken)
amzn.to/3UvO4sF
Seal Puller (this one is garbage, get a better one if you can or use it once and return it like I did)
amzn.to/3up9v44
Rear Differential Fluid (80W90 Gear Oil)
amzn.to/3OzQEKB
Grease Gun Kit w/ Grease
amzn.to/3Us1GoL
Transfer Case Fluid (Transmission Fluid)
amzn.to/3Svst0N
Manual Oil Pump
amzn.to/496mDu0
Fluid Catch Pan
amzn.to/3w2BVRT
30mm Socket
amzn.to/4923l9e
32mm Socket
amzn.to/49s9JGD
Tiny 1/4" Drive Socket Wrench
amzn.to/42w6Kul
11mm Ratcheting Wrench
amzn.to/483l2nn
PB Blaster
amzn.to/49p9nAl
Paint Marker (don't use a China marker like I did)
amzn.to/3SOoG0b
Replacement Yoke w/ Pinion Seal, Nut, and Washer (I would replace this if I could do it over)
amzn.to/487N3dq
*These are Amazon Associate links, meaning there is no added cost to you but a portion of the sale will go to support my channel.
Disclaimer:
Wrench on your own vehicle at your own risk. Ben Wrenchin' doesn't recommend all the methods used in this video. In fact, some of the methods in this video should never be used at all. EVER. Be smart and safe. Ben Wrenchin' is not responsible for injury resulting from performing actions found in this video. This is only to serve as entertainment purposes and is not meant to be used as suggestion or instruction for how to perform any of the actions contained in this video.
Great sound on this!
Thanks, still needs some work but it is way better
Curious……why did you change the drive shaft? Why didn’t you just change your u-joint?
20:51
Basically, the tang where the snap ring holds the u joint in place was bent so bad that I couldn't get a new snap ring to sit in the groove properly.
31:32 I explain again here why I had to get a new one. Mine was toast after I tried to get the old u joint out.
Thanks for putting the effort on this vedio. My 98 blazer will need a pinion seal changed as it'sleaking.Can this job be done without a impact wrench? Thanks.
It can. I would suggest the same socket (32mm I think) and a long breaker bar. The longer the better. If you don't have a breaker bar, you can slide a pipe over your ratchet, I use the handle from my jack for that sometimes. That's all you should need it for is the nut that holds the yoke on. Good luck!
Thanks man. I will be using a breaker bar or a pipe to loosen the bolt. Thanks for the info. 🙏
@@sar9907 No problem, let me know if you need more info. You can do it!
@@benwrenchin first of all i need to pull the old seal out. head to part store to make sure it matches. There's too many different types and have no idea which one will fit.
@@sar9907 try rockauto.com they have a really good list of parts for so many vehicles, then you can know the correct part number and order it before you start the job