Cheapest UTV Fixed For Under $300
HTML-код
- Опубликовано: 16 авг 2023
- I buy the cheapest Yamaha Rhino 660 and fix it for less than $300. #Yamaha, #Rhino,
►SUBSCRIBE: / @2vintage
►MY SECOND CHANNEL: • New Polaris ATV Snow P...
► ADD ME ON ALL SOCIAL MEDIA ◄
► FACEBOOK: / 2vintageyoutube
► INSTAGRAM: 2_vintage_ / 2_vintage_
► SNAPCHAT the2vintage
► EMAIL FOR BUSINESS INQUIRIES ONLY: 2vintagetooo@gmail.com
Thanks for watching and subscribing!
New videos every week!
The following video features activities performed in controlled environments by knowledgeable persons. DO NOT attempt to duplicate, re-create, or perform the same or similar activities at home, as personal injury or property damage may result. 2vintage( Joe Weber, the persons shown in this video and ANY CONTRIBUTOR, ARE NOT LIABLE FOR ANY such injury or damage. ALL 2vintage( Joe Weber) CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.
2vintage (Joe Weber) makes no representation about the sufficiency of any safety precautions and equipment used in this video.
I’ve learned so much from watching this channel. I have an older Polaris ATV and this gives me confidence that I’ll be able to identify and possibly fix whatever it needs (within reason) keep it up Joe I’m sure there’s a lot of people like me that watch every video.
I'm one of them.
I’m a newbie watching as much as I can to catch up. Between this channel and Mustie1 I oughta be able to fix anything that runs on gas 😀
Glad it fired up. You're gauge probably has some pins inside the gauge where they are soldered to the board probably has cold joints. I had a similar issue with these gauges hard to see with the naked eye so I got a digital microscope from Amazon to inspect and sure enough they were broken just had to resolder them and works like new again.
UTV sounds like it's running great. 👍👍
660, put the 686 big bore on it, massive power difference. My father in law has that same sxs. Physically great shape, motor hurting for power. Took a weekend and did a 686 upgrade on it. Now it's even more obnoxiously loud than before, but tons of power at the ground. Nice find. They still can't compete with the Can Ams but decent low end utvs.
Needs a jbs clutch
You did it the right way to make sure the piston, rings, cylinder, valves and valve seals were good to go. But seeing those oil rings a little stuck as the most likely culprit for the smoking issue, it is possible some Marvel Mystery Oil mixed with oil and fuel could have possibly done the trick without the need for a top end rebuild. Nice work and nice result.
For what you have into it, that's really not bad at all. It's no screaming rocket by any means, but it is a grumbling growler.. nice work Joe
Broooo I finally found a fresh video right when it came out, I love this stuff and just grabbed me a 97 Timberwolf 2x4, after all of the videos I’ma try and do most of the work on it myself gettin the motor running good and not boggin, really thankful for all the info and content you do. Thanks man and keep it goin🤟🏼
Good luck! Thanks for watching!
Awesome to see the Yamaha up and running no smoke no more great workhorse good to go for another life time 💪🏻
Your face was priceless when you pulled the key out and she kept turning over. Thanks for the videos.
Like your content in your videos you take your time going through detail which I like don’t do a whole lot of repairs on small engines but what you do I’m learning more and more 👍🏻parts aren’t cheap though unless I get them through the web than some times o don’t get the right parts
Good work Joe. The tailgate chains could use sleeves to keep the new lenses looking pretty 😊
Great job, Joe! Glad to see it worked out well in the end for you.
Thanks for the cool video!
Ι admire your videos so much thanks to your videos sometimes I'm like it happened to him the symptoms look the same maybe it's that and most of the time it's the same so thank you for showing us all this amazing stuff
Love the cheaper SxS videos. I came for the dirt bike stuff but have learned a ton about quad and 4 stroke engines in general. Love the channel!
I saw mecanics take a rim air valve stem to push on the carb valves to grind them, (39th minute in the video), pushing instead of pulling on them still with the drill! But its really up to the guy doing the job to go by the way he likes, thanks for the video you helped me a lot🙂 Very useful!
You have fun doing that by yourself. I won't do another one. Massive undertaking good luck. Bout 12 to 14 hrs. Great vid!😮
yeah not an easy job
Thanks for making the video of your work. I learned a lot.
Hey man great job on your channel. Keep up the hard work.
Love the videos keep up the good work
Great video. Love watching them.
Great job as usual, I get a kick out of the so called pros telling u what u should do.
As always, nicely done!
Just stumbled across your channel love the videos man. Quality work. Wish I lived in your area I’d buy a SxS from you.
Plug your merch more man. I have been watching for months and didn't know you had merch! I'll be getting some!
Good work. It would be nice to see you completely clean this UTV.
Wow wish my old Polaris CV axles were that easy. They have roll pins that you have to back out before pulling the axle and it's a nightmare to take off, especially an old one like a 2000 model. Great video good job.
Good JOB,all the BEST from WALES UK 👍👍
That bearing looks like it got hot! There to much play side to side. Needs a new crank. Look at the piston there’s a lot of scuffing on the sides. Great vid Joe. Keep up the good work.
Damn you got all the UTV’s, Good to See You Living the Dream!
I think it's time for you to go to the next level and purchase a micrometer to measure cylinder bore diameter and taper.
As far as honing goes the expandable is the best for removing very slight taper, the ball hone is only used for cross hatching the bore.
A clean engine is a happy engine.
Great video as always
awesome fix. I have 9400 miles on my 2006 660 engine has never been rebuilt and can still hit 54 MPH.
Great vid, things "shade tree mechanics" should be checking on their UTV's. Quick flip, or add to the fleet?
Come on mate iv watched u for years but lost my account and you have just popped up on this one been watching u since early day when you and your bro used to race up and down street on cr80 vs a 85 or 125 cc glad I found u again man
Love your content! You got to get some Milwaukee m12 ratchet and m18 Fuel impact..save your hands!
I'm the opposite of mechanical, but watching this is highly entertaining and hoping your genius will rub off on me a bit
In my book your a master mechanic freak the haters brotha
I'm pretty sure I could watch a video about brain surgery and somebody in the comments would say they're doing it wrong.
This guy is awesome. Love his videos. Would love to have his set of skills and level head
Just a tip for removing the valves. A small pen magnet makes dealing with those little valve keepers a breeze.
52:09 😂😂 have to weld up that exhaust
Very cool you fixed it… clean add a grand to its value just a thought. Not to mention the grime compounds heat!
Rhino 660, best side by side I've ever owned. Most fun too.
With how much you use impacts you should invest in a Milwaukee 1/2 inch impact. Works great for removing lug nuts and hubs
Those are great but do you think they have more torque than the pneumatic tool that he used?
@@T0tenkampf most definitely not. If you can use a pneumatic tool that’s good but some places or like not near home is what o was referencing too
Hey brotha how do you feel about niche cylinders with wiseco pistons? Wondering what your experience has been with it
love the videos. Harbor freight should sent you one of there offroad jacks then you wouldn't have to drag your big jack around.
You are living the dream 💙👌🏾
have to appreciate how Joe drives past the camera just to get the shot and has to go back to pick it up. Am I watching 2vintage or Les Stroud ? :D
I would assume if the piston was changed and the heat mark on the crank, I'd like to believe it's been rebuilt as they will heat the one side up and press it out, great video buddy 👌👍
Hopefully! That would be nice!
@2vintage wishful thinking buddy 👌
I have that same jack! It has magic powers!
50:45 sometimes if the battery is really low the gage could act up like that if you don't have good voltage going to it. 👍😎
Shouldn't the ring gap be checked after honing the cylinder?🤔
Do you deep clean after cleaning the cylinder/head or is that not necessary for a engines?
Subjective question here- someone in your shoes skill wise: in a previous comment you mention this as a long job…. Is it fair to say too end rebuilds are a time consuming job (related to sxs vs atv Vs bike) but not technically difficult?
Or do you rate this harder because there could potentially lots of little gotchas that like ring gap, timing, proper torque settings etc.?
When it craked forever with the starter stuck, what did you do to get it to start with one turn of the key?
Just a question as i’m about to do the same on my UTV, are we supposed to grease the CV axle where it goes into tranny? and where you put the wheel on?
Have you ever worked on a polaris xpress 300 and are they worth messing with
The ball hone is made as a clean up hone to give you the proper cross hatches
Slowly turning into survivorman with with these camera angles . Always entertaining 👍
Great video that shifter nob has seen better days
Why are the front tires on backwards compared to the rear tires? Tread is going different directions? Is that for reversing in sand or mud?
1:50 pm. Hello. Got a 96 Polaris 300 that makes a clunking noise in reverse only? Bad front sprocket? Won't climb steep grades either
I notice everything that you work on. Do you sell online too?
The side by side or quad??
I kinda miss the ole handle bar breaker bar…lol
Haha me too
When the battery is Dead, which jumper pack are you using?
Joe, You are fearless
Wow thursday!!! Will u have one tommorow also joe?
Possibly!
Nice video!
is it tunned like that to gently take off from a stop ? or is it you ? or clutch problem ? exhaust sounds hollow
Joe it could use a stock muffler.
I see your workshop is getting quite packed. If you dont build a house on the land then maybe build a giant workshop in the middle and then your test track could circle around it 👍
I'm looking for a side by side to buy. Which one should I buy?
What impact is that you use?
Where online do you find the specs and manuals for all these vehicles?
You need a shipping container on "the land" to protect your toys!
Not a bad idea. I'm hoping to get a poll buying built before winter! Searching around for companies that build them now.
I never purchased an actual breaker bar, I always double wrenched it or found a pipe that fits over the ratchet handle lol
be glad the grizzly 600 engine components are cheap. I rebuilt a raptor 600 recently and HOLY CRAP those parts are getting scarse. Had to get a matching head/valve cover because of the cam journals being messed up on the originals. USED on ebay costed me $700 🙄. This was after ordering a grizzly 600 set only to find out the intake and exhaust ports are different. OOF! lol
Wow that is crazy expensive
Dang that thing is noisy! Normal Rhino sound, needs a silencer on it. Great job man.
Well does it have alittle more power then before.
AT 17:00 just curious, why did u hit the wrench with the hammer? u could have just got another wrench and hocked it on the end and use that.
What size tires and rims on that rhino?
Why replace the piston at all if the one in it is in great shape? Why not just rings and gaskets? Just curious.
A little carb. spray or Ether generally helps start any engine, even brake clean will work...
why didn't you power wash the engine before taking it apart
thats my step 1 for restoring anything, thanks to The Apocalyptic Inventor
The 2004-2006 Rhinos are highly sought after here in Alaska. They are hard to break. Use mine for plowing and logging.
Ok, lets see the blooper reel on this one. At least one wrench had to have been thrown! lol 🖐- --=====🔧
@harmonic, actually the blooper is Vinnie ripping into Joe😅
Heck yeah when you going do that three wheel again brother
Great work Joe! You should take your wedding ring off when working around anything mechanical or electrical. Many people have lost fingers because of their wedding ring!
I’d be curious to know what the old rings gapped at.
hey man. wanted to buy a tee shirt but you store page doesnt work
What did you do to make it finally fire up after cranking forever?
Battery wasn't charged enough
Awesome video
Next episode with this machine will be you replacing a starter😂😂
these things are beasts.
i run the largest active Rhino fan page/help group in the world, and i currently own an 06 660.
i know these machines like the back of my pecker, if you ever need to find something or want some insight on thier quirks, let me know man.
( i typed alottt on the first vid, timestamped, all the problems, parts, everything youd need & need to know as the video went & it did not post/deleted itself, not doing it 2x) lol
I know it needs a new starter now 😂😂
Awesome videos sorry I’m sooo late
Dang dude looks like you're running out of space time for a new shop 😲😲😆
Ignition switch? Maybe that also caused starter to stay on.
I'd just put A bead of clear silicone around the face plate. Of the dash digital gauge cluster unit to seal up.,an block out moisture from getting inside of it anymore.
Make sure that’s not a after market key switch. My Honda had same problem with screen.
So whats the deciding factor of when you wear your gloves?