nice detailed video, you can never stop learning, be a sponge to knowledge when there is much to be learned from. car audio is one of those areas where there is so many avenues, so many variables. you can most certainly wire 4 dvc 4ohm subs to 1ohm. this video is great for beginners with no confusion, also not part of the video is half a dozen other options for wiring, all reaching the same desired ohm load, difference being power handling, impedance, channels of the amp...... car audio had so many avenues of knowledge, never stop learning
Thanks for making this video! I have the exact same CT Sounds speakers and amp. Same split box as well. First time I've ever wired car audio to this extent. Now I know my wiring well be right!
Was looking for a video to help me out with how to do my wires for my speakers. And yours is the best one ☝️! Thank you so much for making this video I’ve subscribed now.
Wow man thanks! Question. I’m doing the same set up. Inside my box it came with 12 gauge speaker wire…..but the wire kit I got for it from Skar is 16 gauge from amp to outside of box connection. Is this ok?
If the box I have has 2 seperate terminal cups for my subs...how would i wire those to get to a 1 ohm load? Do i need dvc 2 ohm or dvc 4 ohm subs? Thank you
I have a 13 w7 hooked up to t1000.1 I bought a LC 1500.1 and tried to connect it (didn’t change any wire on the sub) the amp was clipping at low sound and when I adjust the gain the light for protection keeps flashing no matter how high or low.. can’t the way the woofer is wired cause this or is my amp bad??
I have two dual 4ohm 8" Sundown V3 500w RMS... I'm not sure if i need a mono or 2 channel amp & also what wattage the amp needs to be. i tried looking online but some say it needs to match so 1000w amp for 2×500w subs but some say it has to be 1.5/2× the amount of watts 🤷♂️? Also what ohm load it needs to be... i have a custom made LAB slapbox designed for the 8" Sundowns... Any advice on what amp(watts) and what ohm load it should be?
Okay. I have a question. I have a diamond audio technology D3 600.1 mono block amp with two positive and two negative. I put a speaker to each. I have two 10" Massive Audio GTX104 1400 w max dual coil subwoofers. What would be the best way to run the wires for these subs, series or parallel?
What if I have 2 terminal cups I want to use ..and I want to run two 2ohm subs to to a mono block with 4 subwoofer inputs ....I want to run them at 2 ohm final ..does my amplifier covert it by itself? If this makes sense..
I’m sorry I have a jl hd 750/1 and have a 13tw5 2 ohm sub but my box has room for two. Should I just get another 13 2ohm or can I get a 13 4 ohm? Don’t know what’s best. Hope you can help me.
I have a Ford Econoline van and I want to do I set up with to a 8 inch subs and the room I have under the back seat is 10 in high 38 in wide and 24 " deep and I tried them websites to build a box and I don't understand it so I was wondering if you can help me calculate what I would need and I would want it ported and not sealed
So which woofers hit harder Skar or CT? Is there really a noticeable difference between them? I want to put 4 skar d2 on my 2022 silverado 1500 but don't want to upgrade alternator or get extra batteries. What do you recommend?.
stay under 1000 watt in a class d amp and you should see vary minimal dimming in light when the bass hits with out any upgrades to the elec system if you do class a/b only 200watt cause 400 to 500 watt will dam near make the light go out lol the pains we delt with in the old school days was real hehe
hi good video small question no one is answering me I have 4 jbl stage 1010 subwoofers which each melt 4 ohms I want a connection for a taramps 800.1 amp in 1 ohms can you tell me the connection? thank you😮😮
Question: If you used a parallel series parallel pattern, would it make the same set up? That's what the math is seeming to say to me. I don't know what the difference would be if the outcome was still One ohm, just a thought I had🤣
Ok i need help i just got two new skar 15s and i dont want to blow them and want it to sound good can u help me set it up with some advice. specs are as fallow SUB ENCLOSURE: Enclosure features solid 5/8" MDF construction, charcoal carpet covering, a dual vented design, and terminal cup connectors SPECIFICATIONS: Dimensions: 38" (W) x 16 1/4" (H) x 18" (D); Weight: 55 lbs; Air Space: 4.6 cubic feet 2 skar 15's Dual 1 Ohm Voice Coil Configuration Peak Power: 1,500 Watts RMS Power: 3,000 Watts Competition Grade Pressed Paper Cone Stitched High Roll Foam Surround Advanced Air Flow Cooling System 3" High Temperature Copper Voice Coil Motor Weight: 306 oz Frequency Response: 25-400 Hz Sensitivity: 86.3 dB The amp's are BOSS *R2000M* 2000W Riot Monoblock Car Audio Power Amplifier There is 1 for each
If you mounted terminals on the box for each coil wouldn't that make it easier for experimenting with different setups so you can you don't have to pull the subs out in other words to change wiring configuration, from either series to parallel, I hate having to pull the subs to change it especially if you're just experimenting and testing the differences and bouncing back
Hey bud, will you need to put some wire mesh covers over them to prevent the kids from accidentally kicking them getting in/out of the truck? Does your truck have the Bose system and how are you going to connect the speakers/Amp to that system? I've heard that you can't do it at all? I have a red 2021 High Country Tahoe with the Bose system and would sure like to add more speakers and Amp for some bass!
I own a 20 silverado crewcab and car audio is my thing i got 3x12 scar under my backseat my truck pounds there wired to 1/2 ohm wolfram 3000.1 articwolf anniversary eddition my doors have ds19 6x9 6x5 and a cerwinvega 3.5 x2 in dash and ds19 horn tweet mounted in the floorboard plastic under a/c all i need is a spare battery spare battery big 3 make a 100% diffrence on how ur sys sounds its night and day and gunna get that today i built my sub box and have it tuned to 32hrtz my scar subs are 32 hertz and pushing mids and highs is ds19 600 4 channel amp
I’m a complete noob to this and was wondering if you could help me out I have 2 4 ohm 500 watt peak 12 inch subs and a 100 watt amp and my moms bf wants to wire it so it’s 2 ohm 650 amp
You said something about not ever being able to get a dual voice coil to the same ohm load as they start and that's not entirely true. You can run each voice coil to their own channel on the amp to get the same ohm load. So if you had a 4 channel amp and 2 dual voice coil subs you could run each voice coil to it's own channel and get 2 ohms on each of the 4.
Turning all 2ohms speakers into 1 ohms would not sound great. The higher the ohms the better the sounds so it would be better if you install a 4 channel amp and connect all the speakers individually the get the best of all speakers
Best explanation I've seen on this before. Nicely done.
Very detailed, but simple and understandable demonstration. Thanks for the demo👍🏾
That was pretty straight forward and simple . Your illustrations also made it easier to understand the concepts. Thank you!
Great job explaining and breaking it down. I've watched several videos and I gotta say you've done the best job making it easy to understand.
This vid is gold. I've tried to explain this to my diy friends a million times lol.
Thanks!!
I wish people made more videos like this, thank you so much for the information
super educational & comprehensive! felt like I was in school again!
nice detailed video, you can never stop learning, be a sponge to knowledge when there is much to be learned from. car audio is one of those areas where there is so many avenues, so many variables. you can most certainly wire 4 dvc 4ohm subs to 1ohm. this video is great for beginners with no confusion, also not part of the video is half a dozen other options for wiring, all reaching the same desired ohm load, difference being power handling, impedance, channels of the amp...... car audio had so many avenues of knowledge, never stop learning
Thanks for making this video! I have the exact same CT Sounds speakers and amp. Same split box as well. First time I've ever wired car audio to this extent. Now I know my wiring well be right!
Was looking for a video to help me out with how to do my wires for my speakers. And yours is the best one ☝️! Thank you so much for making this video I’ve subscribed now.
Fr the best video I’ve seen on explaining this
I learned so much in 14 minutes…🙏🏾
Thank you for the video audio tutorial commentary demo editing time & effort
You did a great job teaching & sharing
Been wanting to buy 4 subs but was scared because had no Idea how to wire them vid help a lot thanks 👍
Great information 👍🏼 thanks again 😀I finally got some understanding about the ohm,s
Very helpful and easy to understand. Cheers mate
Beautiful video bro. I now understand how to wire 4 subs now. Just deciding on dual 4 for 2ohm or dual 2ohm for 1ohm
God will bless you in heaven my good sir 🎉. Made it so simple and plain . Now I can buy my speaker and Amp
GOOD JOB BRO, I TEACH THIS TO MY CUSTOMERS👍👍
Hey man thanks for the break down i e been trying to figure this out I was the same set up
Finally a good video
I love your explanation this is amazing 🤩
Good share brother excellent communication skills
finally the video ive been looking for
This was VERY informative brother. Great vid.
Very helpful video. Thank you!!
Great explaining but am I correct in thinking getting it to lower ohm the better? I have 2 8" subs at 4ohm
Watch MBE TALK ABOUT 2 vs 4ohm ..
U like those ct sounds better than the old skars u had before?
Wow man thanks! Question. I’m doing the same set up. Inside my box it came with 12 gauge speaker wire…..but the wire kit I got for it from Skar is 16 gauge from amp to outside of box connection. Is this ok?
Best explanation I’ve seen. Thanks!
Great video. what happened to video 2 and 3 of this series
Hi, Leaman. a little help please. what would be the best subs to get the most rms power out of my old school D81000 amplifier???
Best way to wire 2- dual 4ohms 10" cvx.
2ohms or 8ohms? Series or parallel on a Sundown SIA 2500d amp?
I'm trying to figure out if I need dvc 2 or dvc 4 trying to get 1 ohm on 16 speakers. Or I can just run 4 amps 1 amp per 4dvc 2
If the box I have has 2 seperate terminal cups for my subs...how would i wire those to get to a 1 ohm load? Do i need dvc 2 ohm or dvc 4 ohm subs? Thank you
I have a 13 w7 hooked up to t1000.1 I bought a LC 1500.1 and tried to connect it (didn’t change any wire on the sub) the amp was clipping at low sound and when I adjust the gain the light for protection keeps flashing no matter how high or low.. can’t the way the woofer is wired cause this or is my amp bad??
I have two dual 4ohm 8" Sundown V3
500w RMS... I'm not sure if i need a
mono or 2 channel amp & also what
wattage the amp needs to be. i tried looking
online but some say it needs to match so
1000w amp for 2×500w subs but some say
it has to be 1.5/2× the amount of watts 🤷♂️?
Also what ohm load it needs to be... i have
a custom made LAB slapbox designed
for the 8" Sundowns... Any advice on what
amp(watts) and what ohm load it should be?
So I should order4 2ohm speakers single voice coil to connect a 1ohm amp?
Okay. I have a question. I have a diamond audio technology D3 600.1 mono block amp with two positive and two negative. I put a speaker to each. I have two 10" Massive Audio GTX104 1400 w max dual coil subwoofers. What would be the best way to run the wires for these subs, series or parallel?
Wowwwwww I actually get it now. So pretty much you want to get the most power out of the amp by going into 1 ohm correct?
What kind of wire are you using to connect the negative and positive terminals on the speakers together?
u figure that out?
What if I have 2 terminal cups I want to use ..and I want to run two 2ohm subs to to a mono block with 4 subwoofer inputs ....I want to run them at 2 ohm final ..does my amplifier covert it by itself? If this makes sense..
I’m sorry I have a jl hd 750/1 and have a 13tw5 2 ohm sub but my box has room for two. Should I just get another 13 2ohm or can I get a 13 4 ohm? Don’t know what’s best. Hope you can help me.
Can i just parellel the postives n leave the neg single ?
Great video ..
Hell yeah, thanks for helping me understand!
How can I hook up 6 8inch subs to one class d monoblock amp? Lmk bro thank you vm 🤙🏽🤙🏽🤙🏽
How do I can do that same box for a 2006 Ford F150 XLT 4/8
Can you do an example with 2- 4ohm and 2-2ohm ?
Excellent explanation! Gracias. Subscribed
very nice u teach 👍
Nice! Im doing (8) 8inch 4ohm dvc wired to 1ohm... rockville 500 watts x 8!!! And an epicenter
So could you do series series parallel? End with a 4 ohm load?
Help me out with my exact setup thank you
I have a Ford Econoline van and I want to do I set up with to a 8 inch subs and the room I have under the back seat is 10 in high 38 in wide and 24 " deep and I tried them websites to build a box and I don't understand it so I was wondering if you can help me calculate what I would need and I would want it ported and not sealed
So which woofers hit harder Skar or CT? Is there really a noticeable difference between them? I want to put 4 skar d2 on my 2022 silverado 1500 but don't want to upgrade alternator or get extra batteries. What do you recommend?.
stay under 1000 watt in a class d amp and you should see vary minimal dimming in light when the bass hits with out any upgrades to the elec system if you do class a/b only 200watt cause 400 to 500 watt will dam near make the light go out lol the pains we delt with in the old school days was real hehe
hi good video
small question no one is answering me I have 4 jbl stage 1010 subwoofers which each melt 4 ohms I want a connection for a taramps 800.1 amp in 1 ohms can you tell me the connection? thank you😮😮
Thank you!
So if I want 4 8 inch wired to 4 ohms , do I buy the 4 speakers as 2 or 4 ohms
Thank u very much 😊
Question: If you used a parallel series parallel pattern, would it make the same set up? That's what the math is seeming to say to me. I don't know what the difference would be if the outcome was still One ohm, just a thought I had🤣
Can you help me
Out I have two e15 duel 2ohm
I want 1ohm
At the min there half ohm I don’t like
Thanks bro best explanation
Can't wait to hear it buddy
How many watts is that amp
Ok i need help i just got two new skar 15s and i dont want to blow them and want it to sound good can u help me set it up with some advice. specs are as fallow
SUB ENCLOSURE: Enclosure features solid 5/8" MDF construction, charcoal carpet covering, a dual vented design, and terminal cup connectors
SPECIFICATIONS: Dimensions: 38" (W) x 16 1/4" (H) x 18" (D); Weight: 55 lbs; Air Space: 4.6 cubic feet
2 skar 15's
Dual 1 Ohm Voice Coil Configuration
Peak Power: 1,500 Watts
RMS Power: 3,000 Watts
Competition Grade Pressed Paper Cone
Stitched High Roll Foam Surround
Advanced Air Flow Cooling System
3" High Temperature Copper Voice Coil
Motor Weight: 306 oz
Frequency Response: 25-400 Hz
Sensitivity: 86.3 dB
The amp's are BOSS *R2000M* 2000W Riot Monoblock Car Audio Power Amplifier There is 1 for each
If you mounted terminals on the box for each coil wouldn't that make it easier for experimenting with different setups so you can you don't have to pull the subs out in other words to change wiring configuration, from either series to parallel, I hate having to pull the subs to change it especially if you're just experimenting and testing the differences and bouncing back
no matter wut u do u would have to remove the subs and reconfigure the wiring. U cant wire them both ways at the same time
Man great video
really good info bro 🤘🏽
Where can I find the box?
Thank you sire
Can you do a dvc 4 ohm with 4 total subs to a 1 ohm load ?
No. Unfortunately not.
@@leamangriffin what would be the best way to wire 4ohmz 4 total to a 5k taramps 1ohm amp
How to wire the four 2 ohm subs to two amps??
Need help!!!
Thank you
Finally a video for my dumb ass that I understand lol
Hey bud, will you need to put some wire mesh covers over them to prevent the kids from accidentally kicking them getting in/out of the truck? Does your truck have the Bose system and how are you going to connect the speakers/Amp to that system? I've heard that you can't do it at all? I have a red 2021 High Country Tahoe with the Bose system and would sure like to add more speakers and Amp for some bass!
I have another video where i go over that!
I own a 20 silverado crewcab and car audio is my thing i got 3x12 scar under my backseat my truck pounds there wired to 1/2 ohm wolfram 3000.1 articwolf anniversary eddition my doors have ds19 6x9 6x5 and a cerwinvega 3.5 x2 in dash and ds19 horn tweet mounted in the floorboard plastic under a/c all i need is a spare battery spare battery big 3 make a 100% diffrence on how ur sys sounds its night and day and gunna get that today
i built my sub box and have it tuned to 32hrtz my scar subs are 32 hertz and pushing mids and highs is ds19 600 4 channel amp
I felt like I was using algebra again, all these steps just for one thing
i like 8ohm speakers
I’m a complete noob to this and was wondering if you could help me out I have 2 4 ohm 500 watt peak 12 inch subs and a 100 watt amp and my moms bf wants to wire it so it’s 2 ohm 650 amp
Are they dvc subs or svc? Svc will have 1 positive and 1 negative hookup per sub. Dvc will have 2 positive and 2 negative.
@@leamangriffin it’s svc it says single voice coil 12” sub
Svc you would wire the two parallel to achieve 2 ohm.
@@leamangriffin I meant 1000 watt amp not 100 sorry if that confused you but thank you
No problem!
💯💯
Bass Cannon
✅✅✅
Boom it up
NOT BAD AT ALL YOU SHOWED ME HOW TO DO THIS RIGHT THINKS
@@harvinjones8003 yes sir any time
Yep they never tell u details as long they sell it..
You said something about not ever being able to get a dual voice coil to the same ohm load as they start and that's not entirely true. You can run each voice coil to their own channel on the amp to get the same ohm load. So if you had a 4 channel amp and 2 dual voice coil subs you could run each voice coil to it's own channel and get 2 ohms on each of the 4.
Iwantfreestuff 2of
Turning all 2ohms speakers into 1 ohms would not sound great. The higher the ohms the better the sounds so it would be better if you install a 4 channel amp and connect all the speakers individually the get the best of all speakers
i just watch this video and i dint understand it at all am gona pay for it to get done i got the same subs