Reason for the higher rev range at first start up is older vehicles like these start with a higher idle speed to reach proper operating temperature first. After which it’ll begin to drop and finally idle around the 700 range. If you look at newer engines and how newer vehicles idle at start up, they begin at a low idle because it has better monitoring and sensors to be able to obtain the best air to fuel ratio. These older model vehicles don’t have as good sensors and monitors to keep the rev range low at initial start up.
Before you take anything apart you should perform an idle relearn procedure. Turn key to run, then off twice without starting engine, then start engine and wait a few minutes until idle settles in the 800rpm range.
I fixed my 06 Vitz in 5 minutes,adjusted the accelerator pedal switch block its adjustable just go behind the accelarator pedal and you will see a slotted black box with 2 screws,loosen the screws and moved the black switch box and few milliemetres and hey presto idleing beautiful.I dont disagree with what Peter is saying,but my car was nearly stalling and badly shaking,will do the correct things soon.
Dirty mass airflow sensor reduces fuel economy not the idle. It usually the dirty "Idler control valve sensor" that causes the idle to drop to 500-600 RPM. This problem causes the alternator not to be able to produce enough charge and Overtime, this reduces the life of your battery and alternator. This happened to my 2007 Camry, and the only way is to clean the ICV sensor and lubricate the valve, which sits on intake air manifold right after air filter assembly.
I have worked on Toyota's for almost three decades. The mid 90's and newer have been prone to intake manifold gaskets leaking causing a wide variety of problems.
Had rough idle issues on my 2010 Corolla for years. Did the basic checks; air filter, mass airflow sensor cleaning,etc. Turns out it was a leak from the intake manifold and a sticking PCV valve. Replace the valve since you already have access to it when replacing the manifold gasket.
Thanks for this video. Appreciated. The Australian 2008 engine is not the same as this. I found my sensor. It's smaller and easier to remove in slightly later engines. After a good clean idling seems to be perfect now. They want $250 for a new one here in OZ so maybe try removing and cleaning first.
Actually I had this problem with an 06 corolla now I’m having it with an 06 Matrix 1zz ... cleaning the MAF sensor did help. I also replaced the PCV valve at the same time. Doing the same thing on this matrix and the timing chain tensioner
Clean the throttle body too.I would remove,clean or replace the PCV also as doing all 3 of there (incl the MAF in this video) Doing this every 4 or 5 yrs whilst doing a service on the car when you change the spark plugs is a good thing,as you won''t forget to do it all in one go.This is what i do...never had an issue on my 2002 Yaris in 12 yrs of ownership.Don't use cheap supermarket petrol is another strong advice,95% of the time i use Bp,Shell or Esso.
This week my corolla started acting weird. Cold start : 2200 rpm After less than 1 minute, it started jumping between 600 and zero (!) rpm I cleaned the mass air flow sensor like you did,disconnected the battery for 10mins and it seems fixed now! Thanks, keep up the good work ;)
Dude, the area of the MAF sensor you were referring to is the intake air temp sensor. Time is combined with the MAF. The actual MAF part is inside the passages next to the air temp thermocouple. If you look inside these passages you will see two small "wires". That is the MAF part of the sensor. That must also be cleaned. Very carefully.
It help a lot to use a small film of electric grease or vaseline on o ring. So you don’t pinch it and it slide right in and seals. Electric grease also conditions the rubber o ring
Today..i and my wife struggling in d middle of traffic jam..with 38deg c..sweating.. Found your video..do exactly as you did..and the car idling ok..its was the sensor dirty..thank you for tour videi..that make someone there life much more easier..thank you
Hello Peter, When I start my Toyota Vios(2007) w/ 1.3 VVT-i engine, it starts with 2500-3000revs. After about 2 minutes, it will go down to 1000revs. Is there any problem in my car?
Hello, thanks for your video. One question, I have a 2008 Toyota Corolla with 230,000 km of manual gearbox, 1.8-liter engine, type 1ZZ-FE. The fault is that when you turn it on it starts with 1300 rpm and as it warms up it goes up to 2000, that is, it does the opposite since I understand it should go down to about 900 rpm. and when I'm hot I go out and when I make the gear changes I see that the rpm oscillates between 2000 and 1000 rpm and when I continue the march the minimum is 2000 rpm. If I leave it running stopped the car stays at 2000 rpm. I clarify that with a scanner it does not give an error. Well, we took out the carburetor, total cleaning including the MAF sensor of the filter, I clarify that you cannot take out the IAC valve to clean but the carburetor body was immersed in non-abrasive remover liquids and a lot of dirt came out. We measured TPS and IAC with a multimeter, simulated with power and everything was fine. We checked the pipes that had never been touched and were spotless. We put everything together and it starts doing the same fault. Then I disconnected the EGR vacuum valve and there the rpm's dropped a little but after five seconds it accelerates and when connected it returns to 2000 rpm. The same if I disconnect the PCV valve and it idles at 200 rpm until it shuts off. Could it be a fault in the EGR vacuum valve or Crankshaft Sensor and cams (CKP and CMP)?
@@olanonanton8192 Hello, the solution was to change the intake manifold and throttle body gasket and apply the correct torque, which was 89-90. Greetings
@@PeterFinnTheCarDoctor Hello, the solution was to change the intake manifold and throttle body gasket and apply the correct torque, which was 89-90. Greetings
When the engine is cold like in the morning, it is normal for the rpm to be high for some minutes. It should go down as it reach operating temperature.
Yes because it revs higher as the cold engine is trying to warm up quickly, so as to reach normal operational temperature as quickly as possible. More important in winter times where the temperature gets really cold and when it snows as well.
Clean the throttle body too.I would remove,clean or replace the PCV also as doing all 3 of there (incl the MAF in this video) Doing this every 4 or 5 yrs whilst doing a service on the car when you change the spark plugs is a good thing,as you won''t forget to do it all in one go.This is what i do...never had an issue on my 2002 Yaris in 12 yrs of ownership.Don't use cheap supermarket petrol is another strong advice,95% of the time i use Bp,Shell or Esso.
Hello Mr. Peter. I have 2005 year Avensis with 1.8 VVT-i engine and I have had many problems caused by abs sensor. Now I have fixed that and now when I stop the car the idle drops to 600 rpm and goes back to normal after few seconds. It keeps doing that again and again every time I stop the car. I have checked the mass airflow sensor, although it's kinda new. Do you have any ideas what would be causing the problem? Thanks.
@@PeterFinnTheCarDoctor okay thanks a lot. I got the fault codes and it gave me codes P0171, P0174, P0133 for every cylinder and also C1246 & C1201 for braking/ABS-system. I'll check every other ABS-sensors, measure engine compression and clean the throttle body. After that I let you know if I have solved the problems.
Good day sir, ask ko kang po ang problma nang toyota vios na inayos ko...pag mag aircon ka hindi nagbabago ang idle tapos pag bbgyan mo nang gas hanggang 5000rpm bigla mong btawan yong throttle mamamatay yong makina...ano kaya ang sira non...??? Tnx
What is the cause of the RPM decreasing in a fluctuating manner when I take my foot off the gas in first gear? (I have already cleaned the throttle body.) Auris 1,33 Dual vvti.
@@PeterFinnTheCarDoctor Thanks, Yesterday, I checked the sensor you mentioned in your video, and it looked clean. I am eagerly looking forward to your new video.
Peter you told me to check fuel lines 05 Toyota Corolla ce no check engine light on it cranks but it won't start you think it could be throttle body sensor
Will this fix issues with the Valvematic system??? Recently had the check engine light come on, following which scan codes p1047 and p264a came up. Overall, been experiencing issues with rough idle/speed cuts, laziness and car shutting off during traffic stops.
Haii Peter, thank you for explaining how this works. I do really like the way you show every step to take, use simple words. Much appreciated. Can you tell me if this film can be used for the Avensis Verso 2004 VVTi engine, like you other movies? And can you tell me where I can find the park assist computer for parking distance sounds? I want to put one in and put sensors on it. Thank you once more!
Peter, very good advice and easy to following! I have a problem with a 1.6GLE 2005 corolla, at first it would swing then start. Drove 100km and parked after that it won't start just swings until the battery dies?
Hi Peter, Thanks for mangy good videos. I have a corolla 1.6vvt year 2006. When cold it revs 1500rpm but when hot it revs only 600rpm. It does not have this mechanical adjustment like in your video. In stead the idle air plate seems to be electronically powered. I would like to get the revs up to 800rpm. Is this possible to adjust somehow?
I have issue with my altis 2000, during iddle on the traffic jam, rpm drop almost to the lowest number than when i press the gas pedal to go forward there is no respond at all for few seconds, could you advice how to solve it please!
Hello please I need your help I have a Toyota corolla Verso 2008 it is starting but not going in any gear and it's not taking the rev what do I need to do to get it work please
I have a 2005 Toyota Corolla my issue is after the engine warms up my RPM goes to below 1000 at a red light but it is not stable; the issue is it seams like it will stall the engine but there is no check engine light. if I rev-up the engine to be over 1000 RPM then it's ok. i know there is an issue but how don't I know exactly what it is? This is only when the engine is warm and at low rpm like idling at a red after it warms up it's ok... any help would be appreciated. thank-you
I bought a 2003 Toyota Yaris Verso a few months ago and then realised that when the motor was hot and I turned it off, the engine would not start again. I read and learned about replaing the idle air intake valve and also replaced the MAF sensor. Also a new air filter. But now when I start the car, it revs up to 2000 rpm when it is cold. What have I done wrong? Please help.. I am in Norway where it is so expensive to use a mechanic... Dee
My toyota corolla 2005 ce has 264,878 miles and runs good the only problem is when u stop like in a red light the car start shaking and goes to 800 rpm but driving the car dont do that But the only way the car dont shake when u stop is when u have the ac higher and the fan is always on and stays on 900 rpm with ac What can i do ? My husband does the proper maintenance every 3,000 or sometimes less then 3,000 no lights on
Check the moter mound's because they might be hard and cracked from age and above idle it'll have no vibration and maybe get some injector cleaner and put it in the tank and that should fix it
Hey there, thanks for sharing info, cool stuff you do! I have problem with my vvti 1.6 2001. When I start the car it idles very bad. When otside is worm its arround 200-300 rpms, but when weather is cold it can not work at all. I have to keep the gas in order to work, but after a minute or two this issue dissapear and then car works normaly. Airflow sensor is new. Do you know what may be issue?
I think you have errors: Throttle body is bad ( Link: ruclips.net/video/tu9bIoMkEk0/видео.html ) or compression pressures in the engine. Measure the engine cylinder pressures first. ( Link: ruclips.net/video/UJEhaP5LllA/видео.html ) Hey there, thanks for sharing info, cool stuff you do! I have a problem with my vvti 1.6 2001. When I start the car it idles very badly. When otside is worm its around 200-300 rpms, but when weather is cold it can not work at all. I have to keep the gas in order to work, but after a minute or two this issue disappears and then the car works normally. Air flow sensor is new. Do you know what may be the issue?
@@PeterFinnTheCarDoctor Thanks for your answer, I'll check that for sure, but I still wonder if maybe the intake manifold gasket could cause this issue....
Hie Peter.I am having problem with my 2001 Irsum which when you start it the rpm 1100 and inceases on its slighty below 2000.What coud be the problem.I have cleaned the sensors and trotle
Hi Mr Finn! I have a one year old corolla 1.6 L 1Zr-fe engine. Rarely when I start the car from a cold start, there is a loud rattle which lasts a few seconds. I have googled this and some people say it is a problem with with the intake VVT-i gear which must be change. Is this true? Grateful to have your expert views on this.
This sound is normal and your car is OK. The oil pressure becomes high in engine and valve caps makes the sound. This is normal and no issue in engine. :-)
Icv, pcv & throttle body already cleaned, but during cold start my rpm goes 1500 then dropping to 500 until my engine dies. After accelerating for 5mins and my engine at normal temperature, my rpm goes to 800 to 900? Any suggestion with my problem? Altis 2002-automatic.
On my 2005 Corolla the idle when cold is steady, but when the engine is warm the idle goes up and down between 600 rpm and 1000 rpm. This makes it tricky to handle at stop lights as it will stall if you don't give it gas, and when you do give it gas it's hatd not to give it a bit too much gas, making it seem like you're a noob or an old lady.
Hello Peter! I`m from argentina, I have a corolla xei vvt-i 1.8 engine 1zz 2005, i got a trouble and i will comment to you, maybe you can help me, when i accelerate i feel a cut in the acceleration like if one cylinder fails and i see a oil consumtion and smell of bruning oil. before an inspection i have find the distribution lock broken an i was think "the cause of il consumtion" but not.. i changed it and the oil consumtion remains. I was make a cylinder compression test and its ok, a throttle body clean, tps sensor test ok, MAF test ok, I was not do a obd2 scann yet thats probably can be a coil? How can i test them? I follow you and yours vids are a good help ! Thanks!!! Juan
I still experience problem even after cleaning and replacing the sensor and hard start plug. What is issue? I have to restart 3 times in the morning or evening after parking all day...
Heyy. Need help here. My engine is 1nzfe 1.5l. I recently change throttle body to 1zz1.8. The car start but the idle so bad. Too low until the engine turn off. My question is. I need to change the Injecter ?? Already clean the throttle body.
Hi Peter I have a Toyota Auris 2007 1.6 vvt-i petrol semiautomatic mmt I noticed a problem with the idle when i put the car in drive mode and release the brake pedal the idle start going up and down If I move the gearbox on neutral everything is fine
Peter, i want to ask a question about engine vibration. I have a 2009 Camry with 2AZFE ENGINE, 2.4L. 215,000 miles. When i am stopped at a light, and the engine is in gear, i get a noticeable vibration. If i shift to neutral, it goes away or is much better. I have the following new parts i installed trying to fix the vibration. New Toyota OEM motor mounts, all 4. New spark plugs New alternator, Denso New water pump. New serpentine belt New coil packs, all 4, Denso. New coil pack connectors, Denso, all 4. New valve cover gasket New intake manifold gasket Newer AC compressor. Has 71,000 miles on it. AC works good. I think the engine is being loaded down when in the drive gear. Engine rpm us 750-850 when idling. Gave you seen this? Engine runs good when driving. Thanks! Dave
Hi my name is Stanley and I have a question. My car havce a problem When you start the engine it run about 4 to 5 second and than it cut off. and everytime you start it it does the same thing again. Can you tell me what's wrong?
Help pls while cleanning my engine bay taking off the tube from the carburetor to the air filter...i have found out 2 open nozzles at the back of the carburetor no hoses. Are those possible...toyota innova 2014 gas...ty
Hey bro im from Guyana 🇬🇾 I have a Toyota Premio 1NZ engine 2011 it's idling 600 I clean the throttle body and change the plugs and same thing can u help please
Hi Peter, can u please assist. I have a Toyota Corolla professional 1.4 4zz. I have replaced my cylinder head and installed new oil pump and new cams and timing chain kit. When it starts it's fine, no noise. But after about 10 minutes the check engine light comes on again and also the low oil pressure sign shows. The water level is fine, and also the oil still looks clear. The idling is bad and I don't know what could be the problem anymore. It is the 2nd time since last year that I have replaced the cylinder head. Can u please help me
hi boss, what the common problem when idle run, engine was jerking, (2azfe engine estima) already replace, coil ignition, plug, fuel pump, injection flushing, manifold gasket, but still happen, later I try pull out ignition coil cylinder no 1 and no 4,just little engine shaking, when I try pull ignition coil no 2 and no 3 the engine heavy shaking, maybe something problem cylinder no1 and no 4,thanks a lot, reply
@@PeterFinnTheCarDoctor tq sir for your reply, last time I already check pressure, all for cylinder around 140 to 150 psi that it is OK? or not enough pressure.
moro corollassa 1.6 vvti 2005 sellainen vika, että lämpimän koneen tyhjänkäynti laskee jonnekin noin 500-600 sitten nousee ylös jonnekin 1000-1100 ja seilaa tätä väliä? missäköhän vika
Hi please I'm having a problem with my Toyota RAV4 2005 model, the ildling is so abnormal and i have check everything and it seems not to be working well what could be the cause
hi Mr peter. I have a toyota yaris model 2010. The vehicle stops suddenly and it doesnt move for some seconds even after giving it full race. Am very upset pliz lemme know what the issue might be. Thank you sir
stops suddenly? explain. do you mean the vehicle will be in motion and decelerate without braking to a stop on its own? do you mean the engine turns off while you're stopped? I have 2011 yaris, manual transmission, but haven't experienced what you described before.
Hello :) is this the same process for Toyota Avensis 2007 1.6 VVT-i engine? :) When I start the car when engine is cold the RPM goes 1600. is this normal because the engine is cold? or do I have to fix something? My car has 76600km. Thank you.
Peter Finn Hello Mr.Finn my Toyota Avensis exhaust is black. I clean it but when driving it get black again. what could this be? please reply. thank you
Hey good day I'm having problems with my toyota corolla 1nz engine I try cleaning the engine an after put in back the oil it start idling high what could cause that
Hi I have a toyota yaris verso. That has an issue when driving over 2000 rev. When i take my foot of the gas it is stuck on about 1100 and don't go below and when i brake it allmost do not want to slowdown. And then suddenly it do. And the motor light is on. I figure it might be the motor that changes the vents? What do you think?
It whas the vvt-i valve that adjust the oil flow to the camchaft. It got broken when adjusting the generator. The solenoid that moves the rod that adjusts the oilflow got tvisted. But worked 90% of the time. 1 bult to lisen puld it out replaced with new part (150€) And it runs great.
Hey Peter I am trying to install my Intake Manifold on my 08 Corolla but I cannot find torque specs or bolt sequence ... Do you know where I can find guides ?
Hello Peter, I have a toyota yaris 2004 1.0 with 1ZS-FE, and the idling is 500 revs (make small vibrations) when the engine is cold revs to 1000 how do you think, is this a problem?
+Igor Nirca Dirty Idle Control Valve sensor causes this issue over 90% at a time. Have the ICV sensor cleaned. Also, it is wise to clean the air flow sensor for better fuel economy and quicker acceleration. I have had the same issue with my 2007 Camry. Take care of it ASAP, because in a long run, it will damage your car's alternator and shorten the life of your car's battery. At 500 RPM the alternator may not produce enough electricity to run everything in your car.
I have a G corolla 2001 auto transmission car, when I start the car first time after a period (usually more than 10-12 hours) the car starts and immediately rpm drops and stop the engine. This happens even in the evening and night. After couple of times starting and pressing accelerator (providing gas) for couple of minutes it works fine. Once it is started it has no problems of starting and stopping it again and again. When I press the brakes while driving and the car is near to stop it starts shaking a lot till it is accelerated to a speed of 20 KM/hour. The problem is more if AC is on. Can you help me in this regards?
I have a 2007 Pontiac Vibe with Toyota VVT-i engine and it idles at 2000 RPM when really cold and 1600 during summer first start in morning. Is this normal? After about 5-7 minutes it goes down to about 800.
Hi Peter I have a 2004 toyota corolla 1.4 vvti. My problem is after driving for a while at speeds like 120kph the idle gets a little crazy and bounces up and down. What could this be? Really appreciate if you reply.
i have put in a complete 1zz engine in a car which was using 3zz and now the idling is at 2000 please assist how to solve this and the engine light and ABS light are on and off.Please assist or should drive a car and see if it ll go because we have tested it yet.
Hello, bad situation, if you mix the engines. Sorry, I don't never mix the engines parts, lots of issues. If I mix engines, so I must change almost engine parts and cables... !
Hope you service it regulary? Clean the throttle body and would remove,clean or replace the PCV also as doing all 3 of there (incl the MAF in this video) Doing this every 4 or 5 yrs whilst doing a service on the car when you change the spark plugs is a good thing,as you won''t forget to do it all in one go.This is what i do...never had an issue on my 2002 Yaris in 12 yrs of ownership.Don't use cheap supermarket petrol is another strong advice,95% of the time i use Bp,Shell or Esso.
@@ndumisothembalakhengcobo4172 yess i already solved the problem, replace with a new ignition coil, And now i have a youtube channel its all about cars problem ruclips.net/channel/UC5fQ6FyqNuGz8BYHzgWVwlw
OK so Peter, I'm just having a hard time understanding your accent at the beginning. Did you say a NORMAL idle speed when starting the engine cold is around 1100 rpm, and a warm idle speed is around 800rpm? I think my idle speed is around those turns when my engine is cold/warm. I notice my car shakes when I'm stopped at a red light. Do you think this is due to the worn out motor mounts OR idle speed issues?
Peter Finn mine is vitz 01 990cc normal cold idle is 600 rpm to 800 rpm till warm idle is 1000 rpm...and when i put gear on neutral which is manuel the idle keep going up and down from 600 rpm to 1600 rpm ...if you could help please thanks you
Hello Peter, I have a 2014 Corolla S manual, the idle rpm is too low (600) causing it to stall frequently driving away in 1st gear. I would like to bring it up to 900 rpm. The gas pedal is electronically controlled. How do I raise the rpm? Thanks! Your videos were very informative but not relevant to our situation because it is electronic.
hi Peter Finn Thank you for your video.. I want to know did you mean that this air leak causes a bad idle speed in cold temperature & then become a normal idle speed in normal operating temperature? OR it causes a normal idle speed in cold temperature & a bad idle speed in normal temperature? I want to tell you my problem in my Corolla 2011 1.8L the problem once I turn on the car in the morning it runs smoothly with 1600 RPM idle speed, then it decreases to 620 in normal temperature which causes vibrating in engine, this vibrating increases when i stop at a traffic light & the RPM decreases slowly to 600 then 550 then 500, i should move the gear pad to N instead of D to decrease the vibrating little, same thing happening in R, when I try to park my car & put it to R with some breaks it vibrates also and i feel it when i set on chair, I should press fuel pedal to remove the vibrating, the crazy & not understandable thing that when I turn on AC, the RPM increases too much to reach near 1000 RPM & the vibrating goes away, there is no any vibrating in the engine, what the hell is that?? I searched & spent a lot about it, I CHANGED: (spark plugs - fuel pump - throttle body - air mass flow sensor - coils) all parts are new from Toyota dealer.. I cleaned injectors by a mechanic handy.. I need a professional mechanics to advise me for any solution or possibilities of this,, Thank You & best regards..
+Peter Finn thanks but they are not easy in my country.. I took the car last weekend to a mechanic & changes the gasket, it was not broken but the mechanic told it is weak & cause some leak, i changed it with a new one but the vibration still exist.. do you know some possibilities t check? even if you are not sure its ok i will accept your suggestions.. thanks
The reason people watch people like you who know a fraction of what needs to be done right with computer scan tools is the stealership charges $140 + when they can get misinformation for free like I did and it cost me a lot to fix my car right there are too many mistakes in your videos that are not even logical like you make it up cause you dont have a clue invest in factory manuals top of the line equipment Dealers dont answer the phone if you want free info where I live please stop making videos and go to wyotech and give youtube back there money there paying you
hey bro sorry i could not take a video but i supposed to tell you that im the second owner of the car i got and when i bought the car the engine light comes on after driving for about 10-15 mins and the guy told me it was an oxygen sensor bank 1 and dont worry about it so its about 1 year since i had the car and now i get alot of jerking when im shifting in reverse or drive is it that the sensor has gotten really bad.?????
hi sir i have toyota corolla xli 2007 and i am facing (rpm unstable) issue. whenever i nutel my car gear during the driving my car rpm cauge not stable between 0 to 2000rpm please help me to resolve this issue.
Hi Peter and all People, In First of all I'd like to say good job with your channel, keep it going! And ask you about my 1.6vvti 124HP Auris 2007. Got RPMs hesitating at 0km/h, its like between 450rpm to 850rpm. And RPMs are hesitating while I'm driving too. Nearly noticeable but about +/- 50rpm. Fast deaf cranky noises when the gas pedal touches floor (in this time I got 2500rpms+, and 3-5gear). - I changed spark plugs already. One of the old one has white cover. Rest of them between black and brown, - Cleaned MAF, Ah almost forgot. ECU doesnt illuminate "check engine". Computer said "no error codes". Im thinking about "knock sensor" and timing chain. Will you help me? Regards Maciej
Clean the throttle body.I would remove,clean or replace the PCV also as doing all 3 of there (incl the MAF in this video) Doing this every 4 or 5 yrs whilst doing a service on the car when you change the spark plugs is a good thing,as you won''t forget to do it all in one go.This is what i do...never had an issue on my 2002 Yaris in 12 yrs of ownership.Don't use cheap supermarket petrol is another strong advice,95% of the time i use Bp,Shell or Esso.
you do know that the idle should drop to 600-700 rpm when the engine is at operating temperature (at least acording to autodata and my local toyota dealers).
hey Mr Peter i have a 2003 toyota corolla and the problem im having is that when i start the car for the first time like on mornings it would take very long before the car can move can you help me please as to some things i can do or check much thanks!!!
Shaun Pakeerah Hello. Of course I can help You. Please take video and send link to me. Video: the problem im having is that when i start the car for the first time like on mornings it would take very long before the car can move
Reason for the higher rev range at first start up is older vehicles like these start with a higher idle speed to reach proper operating temperature first. After which it’ll begin to drop and finally idle around the 700 range. If you look at newer engines and how newer vehicles idle at start up, they begin at a low idle because it has better monitoring and sensors to be able to obtain the best air to fuel ratio. These older model vehicles don’t have as good sensors and monitors to keep the rev range low at initial start up.
But the idiling come down but go up again
This is what happened to my car today,, thanks to Peter. Tomorrow I can point out to the w. Shop. Thanks 👌👌👌
Glad to help
Before you take anything apart you should perform an idle relearn procedure.
Turn key to run, then off twice without starting engine, then start engine and wait a few minutes until idle settles in the 800rpm range.
Thanks 👍😁
Two Screws, and a screwdriver, killed really good information! Keep up the good work.
Thanks and noted 👍😀
I fixed my 06 Vitz in 5 minutes,adjusted the accelerator pedal switch block its adjustable just go behind the accelarator pedal and you will see a slotted black box with 2 screws,loosen the screws and moved the black switch box and few milliemetres and hey presto idleing beautiful.I dont disagree with what Peter is saying,but my car was nearly stalling and badly shaking,will do the correct things soon.
Thanks for feed back. 👍😀
Dirty mass airflow sensor reduces fuel economy not the idle. It usually the dirty "Idler control valve sensor" that causes the idle to drop to 500-600 RPM. This problem causes the alternator not to be able to produce enough charge and Overtime, this reduces the life of your battery and alternator. This happened to my 2007 Camry, and the only way is to clean the ICV sensor and lubricate the valve, which sits on intake air manifold right after air filter assembly.
+kourosh tari Good info. :-)
I already cleaned but still the same
kourosh tari engine light won't come on
kourosh tari Toyota Corolla won't light engine won't come on won't start
kourosh tari ,yes u r correct (clean the ica valve ). Also u can adjust the idle speed by yrself very easy too.
Thank you Peter , you explain very well and save time for so many . kind regards to you
I have worked on Toyota's for almost three decades. The mid 90's and newer have been prone to intake manifold gaskets leaking causing a wide variety of problems.
Good info 👍😃
Had rough idle issues on my 2010 Corolla for years. Did the basic checks; air filter, mass airflow sensor cleaning,etc. Turns out it was a leak from the intake manifold and a sticking PCV valve. Replace the valve since you already have access to it when replacing the manifold gasket.
Good comment, thanks 😃👍
Thanks for this video. Appreciated. The Australian 2008 engine is not the same as this. I found my sensor. It's smaller and easier to remove in slightly later engines. After a good clean idling seems to be perfect now. They want $250 for a new one here in OZ so maybe try removing and cleaning first.
Thanks for the info!
Actually I had this problem with an 06 corolla now I’m having it with an 06 Matrix 1zz ... cleaning the MAF sensor did help. I also replaced the PCV valve at the same time. Doing the same thing on this matrix and the timing chain tensioner
Getting a rough idle in my Toyota Corolla. Will try cleaning this and hope it works.
Clean the throttle body too.I would remove,clean or replace the PCV also as doing all 3 of there (incl the MAF in this video) Doing this every 4 or 5 yrs whilst doing a service on the car when you change the spark plugs is a good thing,as you won''t forget to do it all in one go.This is what i do...never had an issue on my 2002 Yaris in 12 yrs of ownership.Don't use cheap supermarket petrol is another strong advice,95% of the time i use Bp,Shell or Esso.
This week my corolla started acting weird.
Cold start : 2200 rpm
After less than 1 minute, it started jumping between 600 and zero (!) rpm
I cleaned the mass air flow sensor like you did,disconnected the battery for 10mins and it seems fixed now!
Thanks, keep up the good work ;)
pbasses Great work ! And thanks for info.
Peter Finn hello, when i start my tToyotacorolla the km/h jumps to 20km and the car is not moving? how i fix this?
Thanks very well explained. Do you have any tips for a verso being hesitant when increasing revs, particularly when at a road junction or roundabout?
Clean throttle body, set the spark plugs gap check ignition coils..
Noted, good point. 👍
Dude, the area of the MAF sensor you were referring to is the intake air temp sensor. Time is combined with the MAF. The actual MAF part is inside the passages next to the air temp thermocouple. If you look inside these passages you will see two small "wires". That is the MAF part of the sensor. That must also be cleaned. Very carefully.
Thank You for comment. :-)
Exactly what I was seeing!!! You said it for me!!! I agree with your comment.He is not seeing the other two wires!
Replace all four ignition coils with a Denso brand, will idle extremely well if everything else is operating normal. Big improvement.
Yes, good work. :-)
Cirilo
It help a lot to use a small film of electric grease or vaseline on o ring. So you don’t pinch it and it slide right in and seals. Electric grease also conditions the rubber o ring
😀😊
Yes it's fixed I did exactly what you posted in the video thanks!
+Hawii Gaming Thank You. I appreciate Your feedback.
Today..i and my wife struggling in d middle of traffic jam..with 38deg c..sweating..
Found your video..do exactly as you did..and the car idling ok..its was the sensor dirty..thank you for tour videi..that make someone there life much more easier..thank you
Hello Peter,
When I start my Toyota Vios(2007) w/ 1.3 VVT-i engine, it starts with 2500-3000revs. After about 2 minutes, it will go down to 1000revs. Is there any problem in my car?
Change the intake manifold gasket trust me
I have a toyota sienta rev counter is at 500 it switches off if u stop how can i adjust it to 1000r per minute
Hello, thanks for your video. One question, I have a 2008 Toyota Corolla with 230,000 km of manual gearbox, 1.8-liter engine, type 1ZZ-FE. The fault is that when you turn it on it starts with 1300 rpm and as it warms up it goes up to 2000, that is, it does the opposite since I understand it should go down to about 900 rpm. and when I'm hot I go out and when I make the gear changes I see that the rpm oscillates between 2000 and 1000 rpm and when I continue the march the minimum is 2000 rpm. If I leave it running stopped the car stays at 2000 rpm. I clarify that with a scanner it does not give an error. Well, we took out the carburetor, total cleaning including the MAF sensor of the filter, I clarify that you cannot take out the IAC valve to clean but the carburetor body was immersed in non-abrasive remover liquids and a lot of dirt came out. We measured TPS and IAC with a multimeter, simulated with power and everything was fine. We checked the pipes that had never been touched and were spotless. We put everything together and it starts doing the same fault. Then I disconnected the EGR vacuum valve and there the rpm's dropped a little but after five seconds it accelerates and when connected it returns to 2000 rpm. The same if I disconnect the PCV valve and it idles at 200 rpm until it shuts off. Could it be a fault in the EGR vacuum valve or Crankshaft Sensor and cams (CKP and CMP)?
Hi did you get it resolved...I'm experiencing the problem, I have a 2002 1.8l toyota corolla.
Hi, the issue is inside in Throttle body. You must replace that part👍
Hi, the issue is inside in Throttle body. You must replace that part👍
@@olanonanton8192 Hello, the solution was to change the intake manifold and throttle body gasket and apply the correct torque, which was 89-90. Greetings
@@PeterFinnTheCarDoctor Hello, the solution was to change the intake manifold and throttle body gasket and apply the correct torque, which was 89-90. Greetings
When the engine is cold like in the morning, it is normal for the rpm to be high for some minutes. It should go down as it reach operating temperature.
Yes
Yes because it revs higher as the cold engine is trying to warm up quickly, so as to reach normal operational temperature as quickly as possible. More important in winter times where the temperature gets really cold and when it snows as well.
Cleaned my MAF and idle corrected. Thank you!
Excellent!
Greatvideo, was able to fix the idle issue in my girlfriend Corolla by cleaning the air flow sensor.
TmaaTube Great work. :-)
Clean the throttle body too.I would remove,clean or replace the PCV also as doing all 3 of there (incl the MAF in this video) Doing this every 4 or 5 yrs whilst doing a service on the car when you change the spark plugs is a good thing,as you won''t forget to do it all in one go.This is what i do...never had an issue on my 2002 Yaris in 12 yrs of ownership.Don't use cheap supermarket petrol is another strong advice,95% of the time i use Bp,Shell or Esso.
I'd love to have a v6 Corolla I bet those cars move better
Thanks
Hello Mr. Peter. I have 2005 year Avensis with 1.8 VVT-i engine and I have had many problems caused by abs sensor. Now I have fixed that and now when I stop the car the idle drops to 600 rpm and goes back to normal after few seconds. It keeps doing that again and again every time I stop the car. I have checked the mass airflow sensor, although it's kinda new. Do you have any ideas what would be causing the problem? Thanks.
Hi, your engine compression might be low or throttle body could be stuck.
@@PeterFinnTheCarDoctor okay thanks a lot. I got the fault codes and it gave me codes P0171, P0174, P0133 for every cylinder and also C1246 & C1201 for braking/ABS-system. I'll check every other ABS-sensors, measure engine compression and clean the throttle body. After that I let you know if I have solved the problems.
all video that i see is verry usefull becuase i'm a mechanic
+rex melendres Good ! And Thanks Your comment. :-)
Good day sir, ask ko kang po ang problma nang toyota vios na inayos ko...pag mag aircon ka hindi nagbabago ang idle tapos pag bbgyan mo nang gas hanggang 5000rpm bigla mong btawan yong throttle mamamatay yong makina...ano kaya ang sira non...??? Tnx
janjan de guzman wat goddamn language is that
What is the cause of the RPM decreasing in a fluctuating manner when I take my foot off the gas in first gear? (I have already cleaned the throttle body.)
Auris 1,33 Dual vvti.
Noted 😀👍
@@PeterFinnTheCarDoctor Thanks,
Yesterday, I checked the sensor you mentioned in your video, and it looked clean. I am eagerly looking forward to your new video.
Peter you told me to check fuel lines 05 Toyota Corolla ce no check engine light on it cranks but it won't start you think it could be throttle body sensor
Hi, we need to test fuel injectors. I will do new video. 👍😃
@@PeterFinnTheCarDoctor I oready have fuel injectors clean also new fuel pump
Will this fix issues with the Valvematic system??? Recently had the check engine light come on, following which scan codes p1047 and p264a came up. Overall, been experiencing issues with rough idle/speed cuts, laziness and car shutting off during traffic stops.
Yes. Thanks for watching!👍😊
Haii Peter, thank you for explaining how this works. I do really like the way you show every step to take, use simple words. Much appreciated.
Can you tell me if this film can be used for the Avensis Verso 2004 VVTi engine, like you other movies?
And can you tell me where I can find the park assist computer for parking distance sounds? I want to put one in and put sensors on it.
Thank you once more!
Afwijkende Factor Hello. These films works also Avensis Verso.
Clean the Idler control valve sensor, which sits right on top of air intake manifold toward the end of air filter assembly.
+kourosh tari Many Thanks for comment. :-)
Peter, very good advice and easy to following!
I have a problem with a 1.6GLE 2005 corolla, at first it would swing then start. Drove 100km and parked after that it won't start just swings until the battery dies?
Thanks 👍
Hi Peter, Thanks for mangy good videos. I have a corolla 1.6vvt year 2006. When cold it revs 1500rpm but when hot it revs only 600rpm. It does not have this mechanical adjustment like in your video. In stead the idle air plate seems to be electronically powered. I would like to get the revs up to 800rpm. Is this possible to adjust somehow?
This maf sensor clean is good
10:49
Same problem with my 2006 Honda crv. how to fix?
Well, Honda is different car then Toyota. I need to investigate.
I have issue with my altis 2000, during iddle on the traffic jam, rpm drop almost to the lowest number than when i press the gas pedal to go forward there is no respond at all for few seconds, could you advice how to solve it please!
Hi, maybe your engine is so worn out
Hello please I need your help I have a Toyota corolla Verso 2008 it is starting but not going in any gear and it's not taking the rev what do I need to do to get it work please
Noted
I have a 2005 Toyota Corolla my issue is after the engine warms up my RPM goes to below 1000 at a red light but it is not stable; the issue is it seams like it will stall the engine but there is no check engine light. if I rev-up the engine to be over 1000 RPM then it's ok. i know there is an issue but how don't I know exactly what it is? This is only when the engine is warm and at low rpm like idling at a red after it warms up it's ok... any help would be appreciated. thank-you
You may need to check the overall tuning of the engine
Thank you. But sometimes poor battery charge give a higher idle rpm. now i thinking what a type of rtv can seal it withou buying a new china parts
Ok
I bought a 2003 Toyota Yaris Verso a few months ago and then realised that when the motor was hot and I turned it off, the engine would not start again. I read and learned about replaing the idle air intake valve and also replaced the MAF sensor. Also a new air filter. But now when I start the car, it revs up to 2000 rpm when it is cold. What have I done wrong? Please help.. I am in Norway where it is so expensive to use a mechanic... Dee
The 2000 rpm issue did not happen before I replaced the MAF and idle control intake valve.
Hi, maybe your throttle body is bad
Try re-learn, remove negative terminal for 60 sec. After that fix it back the negative..
My toyota corolla 2005 ce has 264,878 miles and runs good the only problem is when u stop like in a red light the car start shaking and goes to 800 rpm but driving the car dont do that
But the only way the car dont shake when u stop is when u have the ac higher and the fan is always on and stays on 900 rpm with ac
What can i do ? My husband does the proper maintenance every 3,000 or sometimes less then 3,000 no lights on
Hi, maybe your engine is so worn out. Maybe throttle body replace could help
Okay i tell my husband so we can change the part , and that problem is bad for my car or what could happend?
Yes, you might need a engine replace or new piston rings. Sorry.
Try changing you fuel injectors cuz it's clogged up so the gas can't combust in the cylinder that's why it's causing to act up like that
Check the moter mound's because they might be hard and cracked from age and above idle it'll have no vibration and maybe get some injector cleaner and put it in the tank and that should fix it
Hey there, thanks for sharing info, cool stuff you do!
I have problem with my vvti 1.6 2001.
When I start the car it idles very bad.
When otside is worm its arround 200-300 rpms, but when weather is cold it can not work at all. I have to keep the gas in order to work, but after a minute or two this issue dissapear and then car works normaly.
Airflow sensor is new.
Do you know what may be issue?
I think you have errors:
Throttle body is bad ( Link: ruclips.net/video/tu9bIoMkEk0/видео.html )
or
compression pressures in the engine. Measure the engine cylinder pressures first. ( Link: ruclips.net/video/UJEhaP5LllA/видео.html )
Hey there, thanks for sharing info, cool stuff you do!
I have a problem with my vvti 1.6 2001.
When I start the car it idles very badly.
When otside is worm its around 200-300 rpms, but when weather is cold it can not work at all. I have to keep the gas in order to work, but after a minute or two this issue disappears and then the car works normally.
Air flow sensor is new.
Do you know what may be the issue?
@@PeterFinnTheCarDoctor Thanks for your answer, I'll check that for sure, but I still wonder if maybe the intake manifold gasket could cause this issue....
Hie Peter.I am having problem with my 2001 Irsum which when you start it the rpm 1100 and inceases on its slighty below 2000.What coud be the problem.I have cleaned the sensors and trotle
Good comment, me too 👍
Hi Mr Finn! I have a one year old corolla 1.6 L 1Zr-fe engine. Rarely when I start the car from a cold start, there is a loud rattle which lasts a few seconds. I have googled this and some people say it is a problem with with the intake VVT-i gear which must be change. Is this true? Grateful to have your expert views on this.
This sound is normal and your car is OK. The oil pressure becomes high in engine and valve caps makes the sound. This is normal and no issue in engine. :-)
+Peter Finn Thanks Mr Finn
Hi Mr. Peter, how to fix my Toyota Altis 2013 model, the rpm is getting high when i press the pedal cluth for gear changing. Thank you.
Really? Please take video and send link to me. Ok ?
Same problem..mr. Elbert your problem is solved or not..if already solved please explain me what is the exact solution.. Thanks God bless you
Icv, pcv & throttle body already cleaned, but during cold start my rpm goes 1500 then dropping to 500 until my engine dies. After accelerating for 5mins and my engine at normal temperature, my rpm goes to 800 to 900?
Any suggestion with my problem?
Altis 2002-automatic.
Thanks for comment. Glad to hear that 😊👍
On my 2005 Corolla the idle when cold is steady, but when the engine is warm the idle goes up and down between 600 rpm and 1000 rpm. This makes it tricky to handle at stop lights as it will stall if you don't give it gas, and when you do give it gas it's hatd not to give it a bit too much gas, making it seem like you're a noob or an old lady.
👍 Noted
@@PeterFinnTheCarDoctor Do you think I need the same fix? It seems that it only goes down too low (600 rpm) when the engine fan goes on. 🤔
Hello Peter! I`m from argentina, I have a corolla xei vvt-i 1.8 engine 1zz 2005, i got a trouble and i will comment to you, maybe you can help me, when i accelerate i feel a cut in the acceleration like if one cylinder fails and i see a oil consumtion and smell of bruning oil.
before an inspection i have find the distribution lock broken an i was think "the cause of il consumtion" but not.. i changed it and the oil consumtion remains.
I was make a cylinder compression test and its ok, a throttle body clean, tps sensor test ok, MAF test ok,
I was not do a obd2 scann yet
thats probably can be a coil? How can i test them?
I follow you and yours vids are a good help !
Thanks!!! Juan
Hi, you could test your coil using obd scanner. Look my video: ruclips.net/video/Ah2ysLIHlw8/видео.html
I still experience problem even after cleaning and replacing the sensor and hard start plug. What is issue? I have to restart 3 times in the morning or evening after parking all day...
Noted 👍
would this method work on 2000 Lexus ES 300? BUT I am suspecting more sensor Issues cam sensor and IAC.
Yes, it should work too.
Heyy. Need help here. My engine is 1nzfe 1.5l. I recently change throttle body to 1zz1.8. The car start but the idle so bad. Too low until the engine turn off. My question is. I need to change the Injecter ?? Already clean the throttle body.
Ok. You have wrong throttle body
Peter Finn what do you mean ?
excellent thanks for sharing good knowledge
My pleasure
Hi Peter
I have a Toyota Auris 2007
1.6 vvt-i petrol semiautomatic mmt
I noticed a problem with the idle when i put the car in drive mode and release the brake pedal the idle start going up and down
If I move the gearbox on neutral everything is fine
Maybe throttle body is bad
Peter, i want to ask a question about engine vibration.
I have a 2009 Camry with 2AZFE ENGINE, 2.4L. 215,000 miles.
When i am stopped at a light, and the engine is in gear, i get a noticeable vibration. If i shift to neutral, it goes away or is much better.
I have the following new parts i installed trying to fix the vibration.
New Toyota OEM motor mounts, all 4.
New spark plugs
New alternator, Denso
New water pump.
New serpentine belt
New coil packs, all 4, Denso.
New coil pack connectors, Denso, all 4.
New valve cover gasket
New intake manifold gasket
Newer AC compressor. Has 71,000 miles on it. AC works good.
I think the engine is being loaded down when in the drive gear. Engine rpm us 750-850 when idling.
Gave you seen this?
Engine runs good when driving.
Thanks!
Dave
Hi, maybe your engine need rebuild. New piston rings ?
Hi my name is Stanley and I have a question. My car havce a problem When you start the engine it run about 4 to 5 second and than it cut off. and everytime you start it it does the same thing again. Can you tell me what's wrong?
Thanks 👍
Help pls while cleanning my engine bay taking off the tube from the carburetor to the air filter...i have found out 2 open nozzles at the back of the carburetor no hoses. Are those possible...toyota innova 2014 gas...ty
If your engine works fine, everything is Ok !
Can we clean idle air control valve with wd-40?
Yeah
Hey bro im from Guyana 🇬🇾 I have a Toyota Premio 1NZ engine 2011 it's idling 600 I clean the throttle body and change the plugs and same thing can u help please
Noted
Hi Peter, can u please assist. I have a Toyota Corolla professional 1.4 4zz. I have replaced my cylinder head and installed new oil pump and new cams and timing chain kit. When it starts it's fine, no noise. But after about 10 minutes the check engine light comes on again and also the low oil pressure sign shows. The water level is fine, and also the oil still looks clear. The idling is bad and I don't know what could be the problem anymore. It is the 2nd time since last year that I have replaced the cylinder head. Can u please help me
Hi, you have maybe cracks in cylinder head or block?
@@PeterFinnTheCarDoctor there are no cracks in block or cylinder head. Pressure test was done. Could it possibly be vacuum?
How much did all the parts cost?
hi boss, what the common problem when idle run, engine was jerking, (2azfe engine estima) already replace, coil ignition, plug, fuel pump, injection flushing, manifold gasket, but still happen, later I try pull out ignition coil cylinder no 1 and no 4,just little engine shaking, when I try pull ignition coil no 2 and no 3 the engine heavy shaking, maybe something problem cylinder no1 and no 4,thanks a lot, reply
Yes, check the pressures inside the cyliders: ruclips.net/video/abm308NYMX4/видео.html
@@PeterFinnTheCarDoctor tq sir for your reply, last time I already check pressure, all for cylinder around 140 to 150 psi that it is OK? or not enough pressure.
Only difference between 1.8Vvti , 2.5 and 1.4Vvri is engine displacement. These 3 engines are similar.
That's roughly... right. But
The 2.5 machine also includes fine balancing shafts in the machine
moro corollassa 1.6 vvti 2005 sellainen vika, että lämpimän koneen tyhjänkäynti laskee jonnekin noin 500-600 sitten nousee ylös jonnekin 1000-1100 ja seilaa tätä väliä? missäköhän vika
Hi, please replace Throttle body
air sensor should be clean and silver not brown ???
Hi please I'm having a problem with my Toyota RAV4 2005 model, the ildling is so abnormal and i have check everything and it seems not to be working well what could be the cause
Thanks for comment
hi Mr peter. I have a toyota yaris model 2010. The vehicle stops suddenly and it doesnt move for some seconds even after giving it full race. Am very upset pliz lemme know what the issue might be. Thank you sir
Hi, please visit the Toyota Dealer center.
stops suddenly? explain. do you mean the vehicle will be in motion and decelerate without braking to a stop on its own? do you mean the engine turns off while you're stopped? I have 2011 yaris, manual transmission, but haven't experienced what you described before.
Hello :) is this the same process for Toyota Avensis 2007 1.6 VVT-i engine? :) When I start the car when engine is cold the RPM goes 1600. is this normal because the engine is cold? or do I have to fix something? My car has 76600km. Thank you.
goku ssj2 Yes, The same engine.
Peter Finn Hello Mr.Finn my Toyota Avensis exhaust is black. I clean it but when driving it get black again. what could this be? please reply. thank you
Hi, do you mean exhaust pipe end ?
Yes the exhaust pipe end. it gets black when driving. when I wash my car I clean it but it get black again the pipe when driving.
@@PeterFinnTheCarDoctor air pump not work changing for new but computer dont see it
Hey good day I'm having problems with my toyota corolla 1nz engine I try cleaning the engine an after put in back the oil it start idling high what could cause that
Ok. You need new gasket to cylinder head cover.
Hi I have a toyota yaris verso. That has an issue when driving over 2000 rev. When i take my foot of the gas it is stuck on about 1100 and don't go below and when i brake it allmost do not want to slowdown. And then suddenly it do. And the motor light is on. I figure it might be the motor that changes the vents? What do you think?
It's is Automatic gearbox
Nicklas Olli Hello. I need to investigate this issue.
It whas the vvt-i valve that adjust the oil flow to the camchaft. It got broken when adjusting the generator. The solenoid that moves the rod that adjusts the oilflow got tvisted. But worked 90% of the time. 1 bult to lisen puld it out replaced with new part (150€)
And it runs great.
Hey Peter I am trying to install my Intake Manifold on my 08 Corolla but I cannot find torque specs or bolt sequence ... Do you know where I can find guides ?
Torque: 30 N·m (306 kgf ·cm, 22f t·lbf )
Hello Peter,
I have a toyota yaris 2004 1.0 with 1ZS-FE,
and the idling is 500 revs (make small vibrations) when the engine is cold revs to 1000
how do you think, is this a problem?
+Igor Nirca Sounds OK. No any issues.
+Igor Nirca Dirty Idle Control Valve sensor causes this issue over 90% at a time. Have the ICV sensor cleaned. Also, it is wise to clean the air flow sensor for better fuel economy and quicker acceleration. I have had the same issue with my 2007 Camry. Take care of it ASAP, because in a long run, it will damage your car's alternator and shorten the life of your car's battery. At 500 RPM the alternator may not produce enough electricity to run everything in your car.
+kourosh tari Thanks for info
I have a G corolla 2001 auto transmission car, when I start the car first time after a period (usually more than 10-12 hours) the car starts and immediately rpm drops and stop the engine. This happens even in the evening and night. After couple of times starting and pressing accelerator (providing gas) for couple of minutes it works fine. Once it is started it has no problems of starting and stopping it again and again. When I press the brakes while driving and the car is near to stop it starts shaking a lot till it is accelerated to a speed of 20 KM/hour. The problem is more if AC is on. Can you help me in this regards?
Hi, your engine looks like old and weak. So, turn off A/C and if issues are still, replace the engine.
My corolla first start up idles at 1900 any idea what wrong?
No that's correct my verso does that aswell
Good comment 😀👍
I have a 2007 Pontiac Vibe with Toyota VVT-i engine and it idles at 2000 RPM when really cold and 1600 during summer first start in morning. Is this normal? After about 5-7 minutes it goes down to about 800.
Yes, normal cold idle
Hi Peter I have a 2004 toyota corolla 1.4 vvti. My problem is after driving for a while at speeds like 120kph the idle gets a little crazy and bounces up and down. What could this be? Really appreciate if you reply.
Throttle body or coolant level.
hello peter I need to know which water line goes to intake and air on a 2003 Toyota corilla 1.8 thanks
Hi, I need to do new video.
That's the idle air control it's a small piece with two small hoses attached to it at bottom of the throttle body.
Can I use petrol to clean?
Yes, Sir
nice video. Now i can do it myself and save money.. thanks
Great work !
I have the same engine 03 corolla it idles bad and dies at stop light with check engine light on
same issue!
I had the sane issue. I cleaned the throttle body and replaced MAF sensor. It went away.
i have put in a complete 1zz engine in a car which was using 3zz and now the idling is at 2000 please assist how to solve this and the engine light and ABS light are on and off.Please assist or should drive a car and see if it ll go because we have tested it yet.
Hello, bad situation, if you mix the engines. Sorry, I don't never mix the engines parts, lots of issues. If I mix engines, so I must change almost engine parts and cables... !
Do you have an online resource where you get your gaskets from?
Rockauto has very good prices compared to the big chains
Sir i have a toyota vios 2nz-fe the problem of my car is that it has very delayed acceleration and has no power . What do you think are the problem..?
I have the same problem of you,. Toyota vios 2007, did you fixed already? Please share with me,. Thank you
@@felsamlopez4448 Have you tried changing the spark plugs? That solved my problem
Hope you service it regulary? Clean the throttle body and would remove,clean or replace the PCV also as doing all 3 of there (incl the MAF in this video) Doing this every 4 or 5 yrs whilst doing a service on the car when you change the spark plugs is a good thing,as you won''t forget to do it all in one go.This is what i do...never had an issue on my 2002 Yaris in 12 yrs of ownership.Don't use cheap supermarket petrol is another strong advice,95% of the time i use Bp,Shell or Esso.
@@ndumisothembalakhengcobo4172 yess i already solved the problem, replace with a new ignition coil,
And now i have a youtube channel its all about cars problem
ruclips.net/channel/UC5fQ6FyqNuGz8BYHzgWVwlw
Thank you sir for this video 🙏🏽
My pleasure
My 04 corola has poor rpm like 400 hundred whats going on there
OK so Peter, I'm just having a hard time understanding your accent at the beginning. Did you say a NORMAL idle speed when starting the engine cold is around 1100 rpm, and a warm idle speed is around 800rpm? I think my idle speed is around those turns when my engine is cold/warm. I notice my car shakes when I'm stopped at a red light. Do you think this is due to the worn out motor mounts OR idle speed issues?
Hi, normal warm idle is about 800 rpm and normal cold idle about 1200 rpm. Thanks, Sir. :-)
Peter Finn mine is vitz 01 990cc normal cold idle is 600 rpm to 800 rpm till warm idle is 1000 rpm...and when i put gear on neutral which is manuel the idle keep going up and down from 600 rpm to 1600 rpm ...if you could help please thanks you
Peter , what did you do to clean the sensor ?
How to clean the throttle body as well
Thank You. :-)
Hello Peter, I have a 2014 Corolla S manual, the idle rpm is too low (600) causing it to stall frequently driving away in 1st gear. I would like to bring it up to 900 rpm. The gas pedal is electronically controlled. How do I raise the rpm? Thanks! Your videos were very informative but not relevant to our situation because it is electronic.
+Ingrid H Hi, please do this service. Look my two videos: ruclips.net/video/dTlTbgKzO9w/видео.html and ruclips.net/video/cnuqxDDbFrQ/видео.html
hi Peter Finn
Thank you for your video.. I want to know did you mean that this air leak causes a bad idle speed in cold temperature & then become a normal idle speed in normal operating temperature? OR it causes a normal idle speed in cold temperature & a bad idle speed in normal temperature?
I want to tell you my problem in my Corolla 2011 1.8L the problem once I turn on the car in the morning it runs smoothly with 1600 RPM idle speed, then it decreases to 620 in normal temperature which causes vibrating in engine, this vibrating increases when i stop at a traffic light & the RPM decreases slowly to 600 then 550 then 500, i should move the gear pad to N instead of D to decrease the vibrating little, same thing happening in R, when I try to park my car & put it to R with some breaks it vibrates also and i feel it when i set on chair, I should press fuel pedal to remove the vibrating, the crazy & not understandable thing that when I turn on AC, the RPM increases too much to reach near 1000 RPM & the vibrating goes away, there is no any vibrating in the engine, what the hell is that?? I searched & spent a lot about it, I CHANGED: (spark plugs - fuel pump - throttle body - air mass flow sensor - coils) all parts are new from Toyota dealer.. I cleaned injectors by a mechanic handy..
I need a professional mechanics to advise me for any solution or possibilities of this,, Thank You & best regards..
+Noor Isleem Hi, please visit with Toyota dealer service. They helps.
+Peter Finn thanks but they are not easy in my country.. I took the car last weekend to a mechanic & changes the gasket, it was not broken but the mechanic told it is weak & cause some leak, i changed it with a new one but the vibration still exist.. do you know some possibilities t check? even if you are not sure its ok i will accept your suggestions.. thanks
The reason people watch people like you who know a fraction of what needs to be done right with computer scan tools is the stealership charges $140 + when they can get misinformation for free like I did and it cost me a lot to fix my car right there are too many mistakes in your videos that are not even logical like you make it up cause you dont have a clue invest in factory manuals top of the line equipment Dealers dont answer the phone if you want free info where I live please stop making videos and go to wyotech and give youtube back there money there paying you
Plus when moving it moves slow then pick up speed
Ok
hey bro sorry i could not take a video but i supposed to tell you that im the second owner of the car i got and when i bought the car the engine light comes on after driving for about 10-15 mins and the guy told me it was an oxygen sensor bank 1 and dont worry about it so its about 1 year since i had the car and now i get alot of jerking when im shifting in reverse or drive is it that the sensor has gotten really bad.?????
Shaun Pakeerah Hello. Please try this fix, it could help you: ruclips.net/video/Y8FBGrCT3rM/видео.html
ddfi
inb
Im having the same issue, did your car get fixed?
That's awesome nice and clear
Thank you too 👍
hi sir i have toyota corolla xli 2007 and i am facing (rpm unstable) issue. whenever i nutel my car gear during the driving my car rpm cauge not stable between 0 to 2000rpm please help me to resolve this issue.
peter ... really interesting your videos, but your voice is necessary to put more feeling and more desire ... when I hear you makes me want to sleep
Hi Peter and all People,
In First of all I'd like to say good job with your channel, keep it going!
And ask you about my 1.6vvti 124HP Auris 2007.
Got RPMs hesitating at 0km/h, its like between 450rpm to 850rpm. And RPMs are hesitating while I'm driving too. Nearly noticeable but about +/- 50rpm.
Fast deaf cranky noises when the gas pedal touches floor (in this time I got 2500rpms+, and 3-5gear).
- I changed spark plugs already. One of the old one has white cover.
Rest of them between black and brown,
- Cleaned MAF,
Ah almost forgot. ECU doesnt illuminate "check engine". Computer said "no error codes".
Im thinking about "knock sensor" and timing chain.
Will you help me?
Regards Maciej
Hi, your car needs new piston rings.
@@PeterFinnTheCarDoctor I think you are wrong. The car is not smoking from exhaust. Not at all.
Hi guys I had the issue when I turned on my Toyota hilux it's not pick up the speed it going slowly, what can I do
Clean the throttle body.I would remove,clean or replace the PCV also as doing all 3 of there (incl the MAF in this video) Doing this every 4 or 5 yrs whilst doing a service on the car when you change the spark plugs is a good thing,as you won''t forget to do it all in one go.This is what i do...never had an issue on my 2002 Yaris in 12 yrs of ownership.Don't use cheap supermarket petrol is another strong advice,95% of the time i use Bp,Shell or Esso.
You said everything went well? RPM!
Noted!
you do know that the idle should drop to 600-700 rpm when the engine is at operating temperature (at least acording to autodata and my local toyota dealers).
+eivis13 Yes, it drop down when warm. :-)
hey Mr Peter i have a 2003 toyota corolla and the problem im having is that when i start the car for the first time like on mornings it would take very long before the car can move can you help me please as to some things i can do or check much thanks!!!
Shaun Pakeerah Hello. Of course I can help You. Please take video and send link to me. Video: the problem im having is that when i start the car for the first time like on mornings it would take very long before the car can move
I spoke with a mechanic an he say it has to do with something in the cam area
Ok
Thank you Peter
Ok and Thanks 👍😃