Programming used replacement ECM on a Chevy Malibu with the new SPS2 via j2534 Cardaq plus 2
HTML-код
- Опубликовано: 27 авг 2024
- If you're in need of service or assistance:
-ECU Repair Services: keyworks.us
-DIY/Pro Resources: autoelectronic...
You can also support our channel by using our affiliate links below (also found in our comment replies), where we may receive compensation for your purchases:
-eBay : keyworks.us/ln...
-Amazon : keyworks.us/ln...
-AliExpress : keyworks.us/ln...
If you'd like to make a direct contribution, you can do so via:
-Cash App: cash.app/$ecur...
-PayPal: paypal.me/keyw...
Your support means a lot to us, Thanks for watching!
Do this cause your car to stop while driving ?
Thanks for this great video. I was trying to reprogram a used 2011 chevy cruze ecm (delphi dcm3.7 ap). After ecm programming when I try to perform the immo learning it shows this : parameter id is not supported, try to reprogram the ecu with correct sps software calibration.
The mistake I did was maybe to keep the registered vin on the ecu during the flashing process. I did not change the vin as you showed it on the video.
Any help is welcome. I am using autel j2534 programmer.
Yes you must change the VIN. You will need to find out if the 2011 cruze is Global A architecture or not. Those you can not do used modules with SPS2. gm-techlink.com/?p=11221
@@ecurepair Thanks for your support. I can see 2011 cruze on that list. So does it mean that there is no way to swap the ecu ? What would be the solution in that case? Using a virgin ecm ? Thanks once again.
For SPS you would need a virgin ecu. For a used you can clone original with aftermarket tools like kess3, i/o terminal, etc.
Hi,I have a 2011 Chevy Cruze 1.8 auto, changed the TCM with used one ( Gen1 ), will GDS2 over write the vin of replaced TCM.Do not have the old TCM any more.
yes, i did one the other day. it’s easier to inhale from the old and just change the vin in sps2, but you can do it. check service information
Professional
did you ever have problem programming a use bcm ?
Only if its global A. gm-techlink.com/?p=11221 . Those I just clone if customer wants to replace with a used one.
thank you
@@ecurepair hey I have a 2012 chevy malibu also I'm going to get a used replacement ecm about how much will it cost
@@cbriggsmkx1436 depends on where your located I guess. parts prob 60-100. programming for pcm and key is prob 120-200 Id guess.
Hello, I’m new into the programming world, I got a maxicom device, mk908p, it comes with a jbox but I can’t program gm vehicles, please help!!
I got th B0389A fault on the Chevrolet Cruze 2010, Will it be able to replace an ECU in this case
You should be ok to replace with used ecu on a 2010 cruze. 2011+ starts a system type called "global A" and you would need to use a new/virgin ecu.
@@ecurepair
Thank you @Keyworks Repair
I am quite surprised why I get that B0389A code because it is linked to Environment Identification, I checked further that Environment Identification is linked to "Global Architecture" models and yes like you mention, for cruze that starts in 2011.
So I will get the DMI(clone)then go ahead and replace ECU and see what happens, in case it fail my question is, how is the resetting done to virginise the ECU, is it through SPS2 as well?
So do I manually enter the correct vin number that's on your car right
Only if replacing the ECM. @1:35 in video the screen that pops up is where you need to manually enter VIN if changing ecu. If using original ecm and just updating or changing a different module then you can just "connect to vehicle". I made a mistake in the video the first time thats why I connected first then had to go back and manually enter it.
@@ecurepair I keep trying to use my vcx nano gm device bit everytime I install techline it delete my current programs and rewrites the. To a point we're every time I choose a device I get am error and force to shut down. Any ideas
@@alexarias3289 Install it, then close your browser and re open it, log back into acdelco, go to "add vin" in the sps menu then when the techline download page opens up there should be 2 buttons now, the left is to re-install, the right is to launch techline. I missed this and reinstalled it a few times not paying attention I was just about to call tech support then I noticed the right button. See @0:30-1:04 in video
@@ecurepair thanks I'm about to check it out hopefully it works
@@ecurepair bro I really need your help I tried everything Everytime I install techline I lose connection to my vcx nano when it comes to chose a device I get 3 option Bosch Bosch and then my device which is in yellow when I click it I get a error and techline goes to shut down mode and then when it allows me to enter I get the no vci connection
for some reason i do not have the override option when trying to program a used ecm
Make sure you do not connect to vehicle with the automatic option. Instead type in the vin on the first screen then connect that way or the override option wont pop up.
Is this still working for you, All I get after manually typing
Vin in left box is Vin miss match, Proceed with wrong Vin or Cancel.
@@henryford4337 yea you just need to proceed with "wrong" vin
If I proceed with wrong Vin, can right Vin then be written? Thanks
@@henryford4337 SPS refers to the VIN you typed in as the "wrong" vin and that if you want to proceed you will overwrite whats currently on the ecm that it considers the correct vin. So to write the VIN you typed you need to select the overwrite button a couple of times through the process.
انت مبدع
Trying to program 2015 buick with a used pcm. Will it work or need a virgin unit? Thanks for posting the video.
Need virgin or clone original.
autoelectronics101.com/index.php/auto-repair-help/list-of-gm-make-and-models-using-global-a-architecture
I could not perform the second part of TDM learning, it keeps re-trying but never goes to 12 minutes screen. When learning the keys manually using the 30 minutes the car will start but if you turn the engine off will not start again unless you perform the 30 minutes relearn.
Use a new unprogrammed key
@@ecurepair Thank you, I will try
@@ecurepair New key did not solve the issue, the original ECU was shorted, either the replacement ECU is defective or the original ECU damaged another module, I even replaced the TDM and still having same issue
Update: The replacement ECU was defective
Can I just buy an ecm and swap it for 2.4 2012 Malibu? Or do I have to have it programmed?
Has to be programmed. Vin and security
@@ecurepair dang that stinks , what’s that typically cost ?
It’s not actually mine it’s one I’ll be working on. Basically they put a used trans in a 2010 malibu bent the rap out of the pins so the tcm in the used trans was a no com. They put the original one in the used trans now they say it won’t do anything. You think that still a programming issue?? It’s the one you have to pull the pan to do.
I think the tcm in this year are only coded by vin so I would assume the original would still work in the case you described and you may have other problems but I'm not 100% sure sorry. You will need to check dtc's. If there are any config error codes then I would take a guess that the ecm was updated past a compatible calibration when they tried to switch it with the donor unit and programming will probably fix it.
I’ll try reprogramming both ecm and tcm together
my security light won't go out after 10 minutes during the key relearn procedure. what could be the cause? thanks.
This is after flashing the ecu?
Currently working on a 2011 Malibu put new ecm when I try programming key the ecm stays on learn mode for immobilized car shuts off after 2-3 seconds
try using a new key to program.
09 malibu 4cylinder.. can i get a used ecu and program? Also could i do it with autel maxysis or do i need laptop?
What’s the ballpark pricing for installing a new ecm on a Chevy Malibu classic lt 2007 normally?
Flashing will probably be about 150 so I guess that + part cost (and any labor if mechanic installs it for you). Used ecus are pretty low cost for these but it really depends on where you go and if they try to mark it up or not.
hello, I will do the same in a car with a wireless key and the switch changes from on to off in 5 minutes do you think I should run it regardless or turn on the car so that it does not happen?
I'm sure there is an official way to do it but I always just stand by switch back on myself quickly if it switches itself off. Never had any issues doing it that way.
@@ecurepair thanks!
I tried to program one the other day. The window that has connect vehicle never pops up for me after I open the program. Purchase like normal, add vin, then it opens the techline and only gives me the option to log in.
You have to open it from acdelco website like old sps not the shortcut on desktop, just delete it to prevent future confusion.
I had the same issue the other day. I uninstalled SPS and reinstalled it. Worked then.
2007 CTS doesn't require online subscription to rewrite a junk yard ecm vin, right?
yes unless your planning to use old ofline tis2k
Will this work on global a modules? I need to replace ecm on 2011 gmc terrain 2.4L with a donor ecm. Any input is appreciated. Thank you.
no this will not work on on global a. Need to use a device like kess3 or i/o terminal. Like this ruclips.net/video/0p7qRlS7T7A/видео.html
How can we test the ecs and pcm
Hello, please say me, i buy used ECU and replace, i want to know, i need to buy 1 vin or 2 ?
Just one. Make sure to not let it auto select. Manually type VIN of the car you are programming
Can you flash a used tcm on a 2010 malibu? Mine won’t move
Yea if you installed another tcm it will need to be programmed before it will work.
Can u use the tech connect from an tablet??
long as its a windows10 or up. Will be fine.
Im from Atlanta need someone to do this o 2017 Malibu do you know anyone
No sorry
Can any one give feedback on the used TCM VIN change of Chev Cruze 2011 on GDS2/SPS2
Should be ok on a 11 cruze. just make sure to select program & replace
What about the incorrect VIN in used TCM
@@heinebester5049 it should correct it
So I’m in the process of flashing a reman ecu in the same platform as your working on in the vid. I flashed the ecu and went to relearn the key. Once there and after clicking start programming the window pops up downloading cals, that loaded completely then the programming ecu spot says connecting to vehicle, I have not gotten the 12 min wait video and I have been hooked up for almost 20 min now on this screen any ideas?
Window not video, sorry
Not sure why its frozen but you can always just do the 3, 10minute waits. Should take care of it.
@@ecurepair thanks I’ll look into that, I usually only do euro stuff I’m not familiar with the 3 ten min wait. Thank you. Good video as well
@@ecurepair I’m not sure why it froze either, I tried to figure it out but never did. However the three ten min wait took care of it! Thank you once again🤙🏻
After so many failed attempts I gave up on used ecm 😢😢😢
The new SPS system has much harder time then the old system for sure.
Oup’s ecm
The new system is garbage
Yea, old system was pretty crappy to tho. Hard for me to decide which is worse.