Brilliant!! Thank you, this is exactly the video I needed. Finally some real information I can use with my first build using this Mother Board with the 6800k.
I was having a lot of problems with booting and finally isolated it that my 3200mhz rated memory needed to run a bit slower to accommodate the overclock. Hoping this helps anyone trying to figure this out and extract as much as they can from their aging system.
I just have to say: Thank you very much! After some days studying to do my overclock, your video was really the most importante thing for me to get started at the right path. Thank you! Keep the good work!
Awesome video; very clear; easy to understand. I learnt so much from this video. For a long time I was too scared to change any settings in the BIOS but your video gave me confidence. Thanks! +1
After some time studying overclock and watching this video I could achieve 4.4ghz on the 6950x at 1.351v with an avx offset of 4. Very good vídeo. Thank you!
@@kountheaim Note that, even having the same motherboard and processor, the results might be different because each peace of silicon have it limits. Your processor might achieve the same or even better configurations with lower temperatures, or not. The important thing to do is try with a lower clock and stress the computer and check your temperatures. Then work your way up until you hit temperatures as high as you would like to go. You always need to check if the overclock is stable too. It is not easy, but after some testing and studying, you can get there. Just be careful, you can burn your processor if not done right. I burned a 6950x once. :X
Really great overclock video. I'm going to attempt this with the same rig next week. I've subscribed and look forward to more videos like this. Thanks for what you do for us PC freaks!
A little voltage seems to go a very long way. I increased my VCORE to only 1.21 and its now running for 1 hour at a temp of 84C and is now set to 4.2mHZ. I am very happy. Don't think I will push this any further. I also set a -3 for the more intense avx which I will test next but I am happy that I finally hit 4.2 and the temp at 100% load is no more than 84 and appears stable.
I have this board, it's great, except for ASUS customer service which is garbage. They are so slow to release up to date drivers. The SupremeFX HiFi DAC wasn't even working in Windows 10 until last week. I sent them a very angry email about this. One weird thing is that the protective plastic film over the IO ports was impossible to remove.
Hi, Thanks for the video. I have 6800k and asus strix x99. I have exactly same settings like you. My problem is that i can hit 4,1 ghz with no less than 1.275v. and 4,2 ghz no less than 1.35 v. I have test it with RealBench 2.43 (one hour Duration) if i put less voltage, it goes BSOD. My cooler is arctic liquid freezer 240. Temperature with 4,2ghz and 1.35v. are between 60 - 70 C with RealBench one hour stress tess. Is it safe to use 1.35v 24/7 ? Is there something to do with this or do i just have very poor processor? :(
lexustheimpaler Most likely something from G.Skill, I just haven't decided on what speed. I just ordered two EVGA GTX 1080 SC's which don't arrive at the warehouse until tomorrow (6-22-16), so I have time to make up my mind.
Amazing guide! Der8auer, question: what would be the settings that would need to be adjusted to allow for a 4.2GHz overclock? I am currently using the same exact hardware configuration and settings (Intel Core i7-6950X Processor @ 4.0GHz, Corsair Vengeance LED (128 GB) @ 3200MHz and Asus ROG RAMPAGE V EDITION 10)! Thank you in advance!
All motherboards should come without I/O shield separate nowadays, biggest pain when putting together a new PC! Great and informative video. First time I heard of the new Intel AVX settings. I"m guessing all them cores making it run warm compared to my older 4930K Ivy-e 6 core even though it's only 14nm and should run cooler. Even under load haven't seen my CPU go over 60 and usually stays in 30's. Looks like a sweet and solid mobo but expect nothing less from an Asus Rampage board;that's all I've been using for years for solid overclocks!
Thanks for the time and effort on this video, planning to upgrade soon possibly to this board, never has a problem with ASUS boards, they build them like the old Nokia phone ;-) and for the CPU the 6850K witch I think is a nice compromise ( I will only have to sell one kidney instead of that and a piece of my liver) but is an upgrade for many years to come, I'm not sure about the RAM yet (unfortunately I play minecraft modded and is cpu intensive.) Cheers and thanks again from" La Canada"
Thanks. A really great video, very thorough. One question though, you said that temps shouldn't go about 95 on full load on the stress test, but other forums have indicated 60-70 is the ideal temps..who's correct?
What cooling are you using for this setup? Custom water cooling? Great video as always :) EDITED: Nvm, I was still in the middle of the video when posted a comment, it's Noctua NH-D15 :)
Hello and thank you for this great video. It has helped me a lot! Question, I bought a 4.4Ghz binned 6800k from silicon lottery. It's supposed to run @4.4Ghz using 1.35v or less. I'm currently running the exact settings in your video with 3200Mhz memory. What settings do you recommend I set to run at 4.4Ghz and even 4.5Ghz?
Vielleicht etwas spät aber ich habe das selbe Mainboard nur mit einem i7-6900k und dem Dark Rock Pro 3 als Luftkühler. Sollte ich die Exakt gleichen Einstellungen nutzen oder hast du einen perfekten Bauplan für diese CPU? (Wo es stabil läuft und für die meisten Funktioniert?) Wenn ich alles so übernehmen würde wie im Video, muss ich dann nur noch mit der Core Frequency der CPU rumspielen oder zusätzlich dann andere Einstellungen mit anpassen?
I tried these same settings at 1.2 volts but trying to get my cpu to stay at 4.2 ghz 24/7 on waterI get a blue screen in games on that setting how much voltage do i need to get 4.1/ 4/2 stable I tried 1.32 and same thing
Hey amazing video I am considering buying both the motherboard and Intel chip set in the next month, I did have a couple of questions maybe you could help me out. 1. What case would you recommend? 2. What would be the top power supply to use with this set? 3. What would be a top Fan to maintain good temperatures? 4. Can this motherboard can handle more multiple video card like the PNY GeForce GTX 1080? 5. I'm planing on getting G.SKILL TridentZ Series 64GB (4 x 16GB) 288-Pin DDR4 would the overclocking process be the same? Thanks again for this great information.
Hey :) 1. case not sure. That's more a thing of personal preference. I like most phanteks, in win and lian li cases. 2. Power supplies: Super Flower, Corsair, Seasonic. Total power depends on the rest of the components. 4- Yes it can handle multiple cards without problems :) 5. Yes that's also no problem. I already used 8x16 GB on this board and could load XMP without problems (3000 MHz)
Hello Der8auer, this overclock dont work with the new updates of WIN 10 1903 and 1809 my specs i7 6950x ,RVE10 ,RAM DDR4 CORSAIR 3000MHZ ,any ideas plz?? Thank you
Hello! I have a question. Your 6950x stays at the overclocked speed. Mine ramps down to 1200mhz. It will jump up to 4000mhz under load but will go back to 1200mhz when done. How did you get yours to stay at 4000mhz??? I overclocked my 3960x on my x79 machine and it stays at 4100mhz. It never moved up or down. I have had no luck with my 6950x in making it stay at the overclocked speed. THANK YOU for your help!
wagagagaggag I hope you are joking do it gradually like if it's at 4.4 set it to 4.5 boot then test and then set it to 4.6 and until you can't boot then lower it back and give it a tiny bit more voltage
I realise i'm late to this post, but for the stress test would you configure your fans to maximum? My liquid cooler keeps temps 70-77 with the fan on second from the highest setting, but I was wondering if stress tests are best done with the fans in set in the middle.
Fantastic Video. I used your settings on my i7 6900K in a Rampage V Edition 10 Motherboard with G.SKILL TridentZ Series 32GB (4x8GB) 288-Pin SDRAM DDR4 3200. Your settings allowed me to get the full 3200 speed of my Ram and a stable OC of 4 Ghz. I did notice a few strange things. My windows 10 Pro would not blank my screen logged in after a few minutes. Also the stress tests passed but on start up a few times windows hung. I went back to default settings and the monitor power off returned to proper operation and the windows hanging stopped. It appears that overclocking (even if it passes the stress test) can cause software anomolies. Any suggestions on what I should try to make it more stable? Thanks your video was great.
Hast vergessen den m.2/u.2 Port zu erwähnen, als du das Board vorgestellt hast, aber sonst ein super Video! War 4ghz das Maximum? Oder hast du noch mehr rausholen können?
nein :) Die meisten CPUs werden 4.1-4.3 GHz machen. Das Basic Setting von mir sollte aber bei jedem funktionieren und dann kann man selbst noch 1-3 Multis ausprobieren.
+der8auer okay, habe mich schon gewundert haha hast du ein paar infos (sicherer oc/Max oc usw) zum 6850K? Habe leider keine 1700€ für den 6950X übrig :D
What's the max frequency I can go with 6800k and if the other settings can be the same? and is all informations provided by cpu-z already in task manager? Thanks for the nice video.
goin pretty well but i seem to be running a little hotter than you. more like 89 degrees for the 279 test. also 4.5W instead of 3.2 you were running. I have a Arctic Liquid Freezer 360 cooler.....any thoughts? seems stable at 86-89....
Looking for some advice, did this exact overclock almost 2 years ago and got 4GHZ and was happy (thank you), I have not played around with anything and figured a day or two that i should try to overclock it a little bit more and perhaps get a better water cooler just for the sake of it. However i before i did anything i went it to CPU-Z just to verify my clock and noticed that it was now at 3.5GHZ with a 35 multiplier WTF? I took a look in about section in CPU-Z and clicked clock there it showed only 1 core on 4ghz. In windows power management it is set to Performance and i have double check everything i could think of. I have rested CMOS, redone the clock several times to no anvil. The Multiplier is stuck on 35 and 3.5ghz in CPU-Z and it is impossible to get it back to its original 4ghz with 40 multiplier. Any suggestion as to what could have happened?
update your mobos bios to the latest avalible. i have a 6850k and mine would only go to 4.0 ghz. some digging and i found that its the windows genuine intel micro code.
Hi ! Nice job and thanks a lot :) I've got two questions for you please. I just buy the same motherboard but this is not the 6950x on it ... it's only the 6900k. Does it change something for overclocking ? The chip run at 1.051V on stock 3200MHz. Do you think that means this is a good chip to overclock ? Thanks a lot have a nice day.
Thank you very much for this video! Great information, easy to follow, and it worked perfectly except I am struggling to get my 128GB of Corsair DDR4 memory to run stable at 3200. The RAM runs great at 3000, but at 3200 it won't boot. :( I did some minor voltage increases but I am reluctant to push it too hard.
i own multiple x99 boards and cpus and have seen similar issues on some of them, only in my case 3200 seems to run fine and 3000 causes a b7 code after which the system will refuse to post
I have an edition 10 with a 6950x, exactly the same as you here, i have the same settings you have set, but in the stress tests i cannot get over 3.5 my bios shows a successful 40% oc at 4.2Ghz but it is as if the cores are capped at 3.5, can anyone help?
Does the Broadwell-E chip like the 6850k work out of the box with this X99 board or would i need a haswell chip first and then need to upgrade the bios or flash the bios?
hi . I to have a asus rampage v edition 10 and intel i7 6950x .your settings for 4ghz working well , nice one mate. Do u have a recommended setting for 4.4ghz or 4.5ghz . thank you
So I have almost the exact same setup. Before I adjusted anything, it was reading 1200 mhz. Once I set everything like you, it was reading 4000 mhz. I loaded up the latest version of prime95 and it dropped to 3700 and temps never got above 73. However, once I shut it down, it instantly dropped back to 1200mhz. I saw that yours jumped right back to 4000. Do you have any idea what I am doing wrong. I am not an enthusiast, but need as much power as possible to shave some time off a process I am doing that is CPU intensive, and time sensitive.
Meiner funktioniert nicht.sobald ich alles einstelle wie im video.will restarten.mein pc geht aus und dann kommt kein unterschied.. wieder im windows und dann geht er auch nur mit 3.2ghz.
no it was a normal 6950X. You can expect 4.1-4.4 with good cooling from these chips. The setting I showed is the basic setting so you can start testing more
Thanks. I am still not sure if i go 6900K or 6950X. May even skip again having a 3960@4700/6C running stable on water for years now. Thanks for the guide tough!
Excellent vid, I want some advice if you can, I have this board, with a custom cooling loop, i7-6850k, I have two different sets of ram available g.skill trident z rgb 64gb ddr4-3466 (8gbx8) & 64gb ddr4-3200 (16gbx4) I want to push to the best combo possible, any advice? Thanks
Maybe it is time we upgrade our cpu, mobo, and mem to 14900k ? :-) I lost my settings on my X99-A/USB3.1 mobo, and it just needs to be faster, so here I am...before I do an upgrade. How is your rig going? (year later)
Klasse Video mal wieder. Ich hätte mal eine Frage, wie bekomme ich ddr-4 3600er RAM mit ner 5820k CPU zum laufen weil ich gehört habe die meisten CPUs lassen max. 2800er RAM zu!? Und wie hoch kann man "in etwa" die Nordbridge Frequenz hoch machen? Dankö.
I keep getting an overclock8ng failed and have to go back to default settings. I noticed one of my ram sticks isn't reading is this likely the problem? Otherwise the system runs ok stock i have i76950x and 64gb ram platinum 3330 but only reads 49152 mb of ram so could it be the ram causing the issue? Thanks great video
@@Jimbo_1977 no and I’ve sold that build and built a way better machine since then now I’m running ryzen 5950x 128gb Corsair dom msi x570 creation motherboard evga 3090 ftw3 and it holds a steady 5.0-5.1
Did this to my computer ........ - i7 6950X. Computer crashed and won't reboot, bios flash didn't work, CPU must of friend.WARNING. *I USED THE SAME SETTINGS AS IN THE VIDEO.
I have same setup with g.skill 128gb 3200 cl14, and done same settings from the video but The processor is stuck on 3000mhz, the ram was ok at 3200, any idea what could be wrong?!
Hi 8auer, wo liegt eigentlich die sichere Voltage-Obergrenze für die 6950x, um "Electromigration" und ähnliche Effekte im Zaum zu halten? Ich bekommen demnächst meine 6950x und werde dann die von Dir beschriebenen Settings probieren (allerdings auf einem X99 Strix Gaming). Danke für das interessant und hilfreiche Video! Chris
Hey Chris! Bleib unter 1.35 vCore und dann ist alles gut :) Normalerweise solltest du damit auch etwas höher kommen als im Video. Die Kühlung muss aber entsprechend gut sein?
+der8auer ... Du hattest ja 1.20v eingestellt. Ist das für 4GHz und einen durchschnitts- 6950x ein typischer Wert? Ich dachte, man bräuchte dafür eher so um die 1.30V. Die ganzen Einstellungen sollten ja auch auf dem Strix x99 funktionieren, oder muss ich noch etwas im Speziellen beachten?
Ich konnte bisher nur etwa 40-50 BW-E CPUs testen, aber davon hat der Großteil 4 GHz mit 1,20 Volt gemacht. Daher der Wert :) Funktioniert zu 100% auf dem Strix. Strix und R5E10 unterscheiden sich nur in ein paar features. Spannungsversorgung und BIOS sind identisch
+der8auer ... Super, danke für diese wertvollen Infos. CPU ist heute geliefert worden, morgen werde ich mich mal damit beschäftigen. Danke nochmals! Grüße, Chris
+der8auer Hi, bin jetzt dabei, Deine Settings auszuprobieren. Es scheint aber so, als ob mit diesen Einstellungen der Aida64 Streß-Test nicht sauber läuft (nutzt AVX). Crash nach etwa 10 Minuten. Was mach ich nun? Voltage hoch auf 1,3V? Bin für eine Vorschlag dankbar.
Does anyone know why a 6950x would not go over 3.5Ghz when coping his settings? I have the exact same chip and an edition 10 rog board, basically the same board. and when I copy his settings and run aida 64E, the clocks sit at 3.5. I cant get em higher. anybody able to help?
The solution that worked for me is ( from Microsoft forum) Take security control of the file mcupdate_GenuineIntel.dll and then disable it by renaming it mcupdate_GenuineIntel.dll.disabled. Reboot your PC and your Multiplicator will work as normal again. answers.microsoft.com/en-us/windows/forum/windows_10-security/kb4100347-intel-microcode-updates-messes-with-cpu/51796b00-75cb-41fb-b587-0df7a1ed8349?page=3
I have this same mb, an h115i cooler and a 6850K, 64 gb (8x8gb) Corsair Dominator Platinum 3000mhz DDR4. With the exception of the RAM XMP profile and the DDR4-3000 Setting, If I carbon copy all the other settings you made in the UEFI bios, should I theoretically be stable and good to go?
I'm using a 6850k, I increased core to 45, did a voltage of 1.25 and cache voltage of 1.2, Set the rest the same except my memory is xmp at 3200mhz, but my cpuz didn't show any improved values at all, even the bios page is still at standard frequencies. May I know why...?
Hi Gay I followed all your steps. But my motherboard is a ASUS X99 Deluxe II. I have a question. My motherboard have actived the Intel Speedstep. With this configuration is better or worse to have it activated?. Some there may be problem to have it activated? Kind regards
I have a 6800k, strix99 and hyperx 3200mhz. Whenever I try to overclock either manually or with Asus software. It fails to boot again and BIOS wont detect samsung 960 EVO my m.2 ssd systemdisk. Any idea whats wrong? It also only accepts me runnning ram at 3000mhz and not 3200mhz. Great videotutorial btw :)
600 ist viel zu viel. Nichtma nen 10 Gbits Netzwerk Onboard gibts dazu. Für bisschen bling, bling und ne 50 Cent Kunststoffplatte drauf zahle ich nicht 200 Euro Aufpreis zum Rampage v Extreme. Aber du kannst mir ja gerne erklären wieso das Board verdient hat mit 600 Euro eines der teuersten Consumer-Boards aller Zeiten zu sein
So frustrating. Stress tested for 5 hours No issues. I was happy too fast. Upon reboot windows would not start unless I unplugged all USB devices. Went back to default (no overclocking) USB Ports work fine again.
Buzz Jump thanks I have it set to 4.2 running 1.21 volts. The USB Problem is because I had a Amazon dot echo plugged in. I unplugged it and everything is working great now
hey, thanks for the post. I have a irrelevant question but would be happy if anyone know the answer or reason, my water cooling system make me really nervous. I had to fill it just a bit to get it about 1cm upper than the incomin water tube every 2 or 3 weeks or it gets noisy bcs of the water level geting low it starts to making bubble and so much noise. Is it normal and the water cooling system should be filled in this short period of time?! I did t even overclocked my 6950x cpu that much just to 3.81 and a 560x radiator with 4 140 fans working just for the cpu!
You guys are mean :) Yes I mean 4000mHZ OK i used the default settings and after a reboot the strange screen off problem is now gone ! I increased the 40 to 4.1 and its been running for 2 hours max temperature is 82.0 C and stable. I was hoping to go to 4.2 but when I increase my core voltage to 1.25 or 1.27 the temperature climbs to 96 C and it crashes. Probably not much of a difference between 4.1 and 4.2 but would like to go to 4.2 if possible. Thanks
Yup most advanced boards like Asus Rampage require at least some basic tweaking in BIOS since stuff like XMP never works at speeds as advertised. At least I haven't seen it. That's why you save a known stable baseline profile like was shown in this video and then can start tweaking more extreme overclocks from there!
HiI have ordered the Rampage V Edition 10 and will order an 6900K.What is the best frequencies i can reach? i saw on many websites than it can't reach 4.3Ghz.... i hope reaching 4.5/4.6Ghz with a EK Fullboard waterblock.Tell me what you think please.Regards.
4.0GHz is a very mild OC for 6850k, you can take it further between 4.2-4.5 but remember every chip is different and you need to increase it just 100Mhz at a time and test before increasing
Hello' first thank you for this Video. can i try this settings for this products i have same cpu 6950X and asus rampage V Extreme ,Corsair dominator 2666MHz thanks
hmm... i have the 6900k with a water cooler Cirsair H105i. Memory Kingstone HyperX 3200mhz. I cant follow you because my system dont boot (monitor black) after i make the OC in the bios... so i think that my system is unsteable. so. ¿What i have to do different at you? memory OC is to much for mines? Help please.
I HAVE THE SAME SPECS 95% the same... AND THIS DOES NOT WORK... PLZ HELP ME. - posted 10.10.19 It hangs and never posts... then I wait and wait to see if the CPU will OVERCLOCK to 4GHZ, when it fails, I get the "OVERCLOCKING FAILED!" message. And I have to press F1 for setup, where all my previous settings are now back to default, ram is 2133 and my 6950X is at 3000MHz, NOT the 4.0Ghz I wanted with the XMP 1 (profile)... help! More Info: I have the same specs with the 6950x... have the corsair dominator quad channel 3333 8gb x 8 =64gb of it... I put in the EXACT settings and the computer restarts-COLD RESTART-and when it does start up, the code in the corner stays at " 6d " -at least I think that's it. I have no idea what that means, it cycles from that to 60 and back to that 6d or is it saying 'bd'... not sure what the code is... JUST KNOW IT DOESN'T WORK. There is one yellow led lit up and blinking next to the code, it is like it wants to start up but something is stopping it and it repeats the cycle of the codes going from '60-69' or' 60-bd' or '60-6d'... Once it does that for a while, the computer completely restarts and loads the old settings. Now I have BIOS 0903... do I have to upgrade to have it working? ANYONE HERE? HELP ME PLZ! I WANT the hardware to run to get the money out of what I spent for it...bid deal to me. Thank you KINDLY. I APPRECIATE ANY FUTURE HELP. 1 idea, instead of 8 sticks of RAM, should I just use 4 and put them in only 1 quad channel slots? 8gb x 4 instead of 8gb x 8... less memory but it might do something... NOT SURE... HELP OB1... ANYONE.
Ah it may be a bit late but looks like that is a RAM issue. First try updating your bios and see if the error code is the same, and if that doesnt work try turning off xmp and try the 4ghz clock. That's it really the error code is on about DXE initialization which means its trying to recognize your ram which could lead to why your xmp profiles aren't functioning properly
@@MegaKayway could you give me all the settings you know of? for faster ram, oc, and faster cpu, oc, separate... and also settings with everything together... I have the newest bios... this is corsair dominators... real nice ram on the QRM-the registered manufacturers that make ram exactly working for this MB... I am curious what everyone here has their setting that work so well... also fastest ram used, make model... all that good stuff... hook me up...for 5 years I never had this baby at 4ghz... it always does something funky after the auto settings... i'll tryp xmp... but I doubt it. Let me know if that error code had anything to do with a GROUND ISSUE? thanks.
@@MegaKayway the ram was recognized... CMD -3333mhz version quad core 32gb and I have 2 of them to fill the 8 slots for 64 total... xmp option sees it fine... I will do the 4.0 without xmp test now. I just have "6d" sitting on the bios output code screen on the motherboard... 6d and a yellow is flashing... meaning what one of the modules is bad? can I still run 7 modules and get full speeds or no? or it doesn't matter if it just one bad module, take it out and try again? with xmp? let me know. thanks and I never got an email about you responding... THANK YOU SO MUCH! lets see if this works.
tried without xmp and nothing... just sat off not booting with the 6d and yellow led flashing... I never got my 6950x higher than 3.0ghz or have my 64gb of ram ever go past 1333... I even have air conditioning and water cooling on the units... it runs at 25-30 degrees C... but as soon as I put it with any of your settings it just sits there and returns to the slow speeds... I think the ram module is broken... I'm trying to make a cancer movie and having ram that works really matters... is there anyone that may help? plz. I can only afford this old computer to do the 4K RAW editing on... and After Effects... and slow video cards because of the super costs. This is for my father, he has the cancer, something that was given to him by bad doctors. PLEASE HELP.
I have same board with 6800K - whenever my cpu is hitting more than 70c it is restarting. Finally i fixed this in the settings by changing the the cpu max temperature manually to 95
Ah super, dann wird es wohl ein 6800k in Kombination mit dem Noctua D-15. Hast du eventuell noch eine Mainboard Empfehlung unter 500€, Herstellungsjahr 2016. Ist die letzte Frage, die sich mir noch stellt, dann kann ich die Bestellung fertig machen. ^^ Das ASUS Rampage V Edition 10 ist schon toll, aber der Preis dafür ist gesalzen. Ich möchte nur moderat Übertakten und keine neuen Rekorde aufstellen. :) Fällt dir spontan eins mit guten Preis/Leistungsverhältnis ein? Habe jetzt keine besonderen Wünsche, außer das es von 2016 sein sollte. ^^
yea up to 4.4 GHz 24/7 stable. Same settings just CPU Core Ratio to 44 and CPU Core Voltage to 1.34. But ofc that depends on the individual CPU quality
Brilliant!! Thank you, this is exactly the video I needed. Finally some real information I can use with my first build using this Mother Board with the 6800k.
I was having a lot of problems with booting and finally isolated it that my 3200mhz rated memory needed to run a bit slower to accommodate the overclock. Hoping this helps anyone trying to figure this out and extract as much as they can from their aging system.
I just have to say: Thank you very much! After some days studying to do my overclock, your video was really the most importante thing for me to get started at the right path. Thank you! Keep the good work!
Awesome video; very clear; easy to understand. I learnt so much from this video. For a long time I was too scared to change any settings in the BIOS but your video gave me confidence. Thanks! +1
After some time studying overclock and watching this video I could achieve 4.4ghz on the 6950x at 1.351v with an avx offset of 4. Very good vídeo. Thank you!
Hello... were you using the same motherboard as shown in this video?
@@kountheaim Yes, I was :)
@@Canal2Playerz Thank you. I have just got the same motherboard and a 6950x from eBay. I will try same configuration.
@@kountheaim Note that, even having the same motherboard and processor, the results might be different because each peace of silicon have it limits. Your processor might achieve the same or even better configurations with lower temperatures, or not. The important thing to do is try with a lower clock and stress the computer and check your temperatures. Then work your way up until you hit temperatures as high as you would like to go. You always need to check if the overclock is stable too. It is not easy, but after some testing and studying, you can get there. Just be careful, you can burn your processor if not done right. I burned a 6950x once. :X
@@Canal2Playerz Thank you very much for your kind advice. I will be careful. By the way, what kind of cooler did you use with this system?
The first interesting tutorial about OC. Thanks mate, you helped me a lot!
Really great overclock video. I'm going to attempt this with the same rig next week. I've subscribed and look forward to more videos like this. Thanks for what you do for us PC freaks!
4THz. That is one quick CPU.
A little voltage seems to go a very long way. I increased my VCORE to only 1.21 and its now running for 1 hour at a temp of 84C and is now set to 4.2mHZ. I am very happy. Don't think I will push this any further. I also set a -3 for the more intense avx which I will test next but I am happy that I finally hit 4.2 and the temp at 100% load is no more than 84 and appears stable.
Tillbaka här 2024
Ska testa att klocka min 6950X
👍👍👊👊🍺🍺🇸🇪🇸🇪
x99 is back from the dead and i love it
I have this board, it's great, except for ASUS customer service which is garbage. They are so slow to release up to date drivers. The SupremeFX HiFi DAC wasn't even working in Windows 10 until last week. I sent them a very angry email about this. One weird thing is that the protective plastic film over the IO ports was impossible to remove.
mine stil dont
I followed your guide and clocked my 6850k to 4.2 , 1.2v . Thank you for showing us how to.
Hey man thanks! I followed your instruction and it's fine. Subscribed. Currently running on 6850K, just bought 6950X awaiting that. :D
geiles vid mal wieder der8auer :D da haut er die 2000er cinebenchs raus
Good video my German friend. Looks like you will win Euro 2016.
Hi, Thanks for the video. I have 6800k and asus strix x99. I have exactly same settings like you. My problem is that i can hit 4,1 ghz with no less than 1.275v. and 4,2 ghz no less than 1.35 v. I have test it with RealBench 2.43 (one hour Duration) if i put less voltage, it goes BSOD. My cooler is arctic liquid freezer 240. Temperature with 4,2ghz and 1.35v. are between 60 - 70 C with RealBench one hour stress tess. Is it safe to use 1.35v 24/7 ? Is there something to do with this or do i just have very poor processor? :(
My Rampage V Edition 10 and 6900k should be here tomorrow.
nice....what RAM you using
lexustheimpaler
Most likely something from G.Skill, I just haven't decided on what speed. I just ordered two EVGA GTX 1080 SC's which don't arrive at the warehouse until tomorrow (6-22-16), so I have time to make up my mind.
Where did you order it from?
GuranTBH
The 6900K was from B&H Photo, the RAMPAGE V EDITION 10 is from NewEgg, and I ordered the GTX 1080's from ShopBLT.
Contemplating between 6900 vs 6950, also i am running a two 1080s, But why did you choose the 6900 over the 6950?
Amazing guide! Der8auer, question: what would be the settings that would need to be adjusted to allow for a 4.2GHz overclock? I am currently using the same exact hardware configuration and settings (Intel Core i7-6950X Processor @ 4.0GHz, Corsair Vengeance LED (128 GB) @ 3200MHz and Asus ROG RAMPAGE V EDITION 10)! Thank you in advance!
All motherboards should come without I/O shield separate nowadays, biggest pain when putting together a new PC!
Great and informative video. First time I heard of the new Intel AVX settings.
I"m guessing all them cores making it run warm compared to my older 4930K Ivy-e 6 core even though it's only 14nm and should run cooler. Even under load haven't seen my CPU go over 60 and usually stays in 30's.
Looks like a sweet and solid mobo but expect nothing less from an Asus Rampage board;that's all I've been using for years for solid overclocks!
hello I bot the rampage v edition 10 and Corsair Dominator Platinum Series 64GB (4 x 16GB) DDR4 DRAM 3466MHz
It will work or no please ??
Excellent. Continue in the same spirit .
Thanks for the time and effort on this video, planning to upgrade soon possibly to this board, never has a problem with ASUS boards, they build them like the old Nokia phone ;-) and for the CPU the 6850K witch I think is a nice compromise ( I will only have to sell one kidney instead of that and a piece of my liver) but is an upgrade for many years to come, I'm not sure about the RAM yet (unfortunately I play minecraft modded and is cpu intensive.) Cheers and thanks again from" La Canada"
It well worked for me on Rampage V Edition 10 + 6950x + Corsair Vengeance Red Lpx 3200mhz 8x8gb 🧐 you rock 🤘
Thanks. A really great video, very thorough. One question though, you said that temps shouldn't go about 95 on full load on the stress test, but other forums have indicated 60-70 is the ideal temps..who's correct?
Higher temp = shorter cpu life. you choose.
After hearing that music twice I feel compelled to rob a liquor store.
thank you de8bauer great overclocking guide.
for videos like this I'm using a R7 250 which is passive cooled. Just to avoid sound while recording :)
Perfekt zum Frühstück!
What cooling are you using for this setup? Custom water cooling?
Great video as always :)
EDITED: Nvm, I was still in the middle of the video when posted a comment, it's Noctua NH-D15 :)
Hello and thank you for this great video. It has helped me a lot! Question, I bought a 4.4Ghz binned 6800k from silicon lottery. It's supposed to run @4.4Ghz using 1.35v or less. I'm currently running the exact settings in your video with 3200Mhz memory. What settings do you recommend I set to run at 4.4Ghz and even 4.5Ghz?
great video sir is the ROG MAXIMUS VIII EXTREME/ASSEMBLY still a faster or higher performance motherboard ?
Terrific guide thank you!
Nice, going to have some fun with my new machine. Rampage 5 Edition 10, 6900K, and 128GB G.Skill 3200Mhz 14-14-14-34 . Fun times.
Dario D'Aversa
wow, what graphics card
Zotac GTX 1080 Amp! Extreme . It's a pretty decent build. Very fast, but I use it mostly for work, not games. :P
Dario D'Aversa
nice
Vielleicht etwas spät aber ich habe das selbe Mainboard nur mit einem i7-6900k und dem Dark Rock Pro 3 als Luftkühler.
Sollte ich die Exakt gleichen Einstellungen nutzen oder hast du einen perfekten Bauplan für diese CPU? (Wo es stabil läuft und für die meisten Funktioniert?)
Wenn ich alles so übernehmen würde wie im Video, muss ich dann nur noch mit der Core Frequency der CPU rumspielen oder zusätzlich dann andere Einstellungen mit anpassen?
I tried these same settings at 1.2 volts but trying to get my cpu to stay at 4.2 ghz 24/7 on waterI get a blue screen in games on that setting how much voltage do i need to get 4.1/ 4/2 stable I tried 1.32 and same thing
Should i use the same voltage for 6800k?
Hey amazing video I am considering buying both the motherboard and Intel chip set in the next month, I did have a couple of questions maybe you could help me out.
1. What case would you recommend?
2. What would be the top power supply to use with this set?
3. What would be a top Fan to maintain good temperatures?
4. Can this motherboard can handle more multiple video card like the PNY GeForce GTX 1080?
5. I'm planing on getting G.SKILL TridentZ Series 64GB (4 x 16GB) 288-Pin DDR4 would the overclocking process be the same?
Thanks again for this great information.
Hey :) 1. case not sure. That's more a thing of personal preference. I like most phanteks, in win and lian li cases. 2. Power supplies: Super Flower, Corsair, Seasonic. Total power depends on the rest of the components. 4- Yes it can handle multiple cards without problems :) 5. Yes that's also no problem. I already used 8x16 GB on this board and could load XMP without problems (3000 MHz)
Hello Der8auer, this overclock dont work with the new updates of WIN 10 1903 and 1809 my specs i7 6950x ,RVE10 ,RAM DDR4 CORSAIR 3000MHZ ,any ideas plz?? Thank you
I had the same problem and it was fixed with a BIOS update.
@@marcleduc1493 Hello what version of bios you have? I have install the last 1903
@@user-he6ot2iy8y The latest BIOS version is now 2101 www.asus.com/us/Motherboards/ROG-RAMPAGE-V-EDITION-10/HelpDesk_BIOS/
Hello! I have a question. Your 6950x stays at the overclocked speed. Mine ramps down to 1200mhz. It will jump up to 4000mhz under load but will go back to 1200mhz when done. How did you get yours to stay at 4000mhz??? I overclocked my 3960x on my x79 machine and it stays at 4100mhz. It never moved up or down. I have had no luck with my 6950x in making it stay at the overclocked speed. THANK YOU for your help!
go to manual mode. Optimal or Auto will throttle the cores down.
Can I do this exact overclock to my 6800k?
wanna know that too =/
wagagagaggag I hope you are joking do it gradually like if it's at 4.4 set it to 4.5 boot then test and then set it to 4.6 and until you can't boot then lower it back and give it a tiny bit more voltage
6800k can overclock 4,2 with 1,37 cpu core with 280 aio water cooler
I realise i'm late to this post, but for the stress test would you configure your fans to maximum? My liquid cooler keeps temps 70-77 with the fan on second from the highest setting, but I was wondering if stress tests are best done with the fans in set in the middle.
Nice tutorial. Thanks!
Fantastic Video. I used your settings on my i7 6900K in a Rampage V Edition 10 Motherboard with G.SKILL TridentZ Series 32GB (4x8GB) 288-Pin SDRAM DDR4 3200. Your settings allowed me to get the full 3200 speed of my Ram and a stable OC of 4 Ghz.
I did notice a few strange things. My windows 10 Pro would not blank my screen logged in after a few minutes. Also the stress tests passed but on start up a few times windows hung. I went back to default settings and the monitor power off returned to proper operation and the windows hanging stopped.
It appears that overclocking (even if it passes the stress test) can cause software anomolies. Any suggestions on what I should try to make it more stable?
Thanks your video was great.
Thanks for the vid, very helpfull
Hast vergessen den m.2/u.2 Port zu erwähnen, als du das Board vorgestellt hast, aber sonst ein super Video! War 4ghz das Maximum? Oder hast du noch mehr rausholen können?
nein :) Die meisten CPUs werden 4.1-4.3 GHz machen. Das Basic Setting von mir sollte aber bei jedem funktionieren und dann kann man selbst noch 1-3 Multis ausprobieren.
+der8auer okay, habe mich schon gewundert haha hast du ein paar infos (sicherer oc/Max oc usw) zum 6850K? Habe leider keine 1700€ für den 6950X übrig :D
What's the max frequency I can go with 6800k and if the other settings can be the same? and is all informations provided by cpu-z already in task manager?
Thanks for the nice video.
goin pretty well but i seem to be running a little hotter than you. more like 89 degrees for the 279 test. also 4.5W instead of 3.2 you were running. I have a Arctic Liquid Freezer 360 cooler.....any thoughts? seems stable at 86-89....
Dafür das du so wenig abos hast machst du echt hochwertige videos :)
thx =) Arbeite daran :D
Can anyone explain to me why the IMC cannot handle memory speeds above 3200Mhz? Is there a website I can learn more about this limitation.
Looking for some advice, did this exact overclock almost 2 years ago and got 4GHZ and was happy (thank you), I have not played around with anything and figured a day or two that i should try to overclock it a little bit more and perhaps get a better water cooler just for the sake of it.
However i before i did anything i went it to CPU-Z just to verify my clock and noticed that it was now at 3.5GHZ with a 35 multiplier WTF?
I took a look in about section in CPU-Z and clicked clock there it showed only 1 core on 4ghz.
In windows power management it is set to Performance and i have double check everything i could think of.
I have rested CMOS, redone the clock several times to no anvil. The Multiplier is stuck on 35 and 3.5ghz in CPU-Z and it is impossible to get it back to its original 4ghz with 40 multiplier.
Any suggestion as to what could have happened?
i have this issue too
Same here! I don't get it, the CPU appears to ignore the ratio entered in the BIOS and keeps its default ratios.
update your mobos bios to the latest avalible. i have a 6850k and mine would only go to 4.0 ghz. some digging and i found that its the windows genuine intel micro code.
Hi ! Nice job and thanks a lot :) I've got two questions for you please. I just buy the same motherboard but this is not the 6950x on it ... it's only the 6900k. Does it change something for overclocking ? The chip run at 1.051V on stock 3200MHz. Do you think that means this is a good chip to overclock ? Thanks a lot have a nice day.
Florian Lalignel I have a 6900k and the best I could do (and be prime95 stable) is 4.4ghz @ 1.290v
Hi der8auer. Can you make a video for X299 overclocking? we really need that
briliant
Thank you very much for this video! Great information, easy to follow, and it worked perfectly except I am struggling to get my 128GB of Corsair DDR4 memory to run stable at 3200. The RAM runs great at 3000, but at 3200 it won't boot. :( I did some minor voltage increases but I am reluctant to push it too hard.
i own multiple x99 boards and cpus and have seen similar issues on some of them, only in my case 3200 seems to run fine and 3000 causes a b7 code after which the system will refuse to post
What do you reckon the single thread performance difference is between the 4930k, and the 6850k?
I have an edition 10 with a 6950x, exactly the same as you here, i have the same settings you have set, but in the stress tests i cannot get over 3.5 my bios shows a successful 40% oc at 4.2Ghz but it is as if the cores are capped at 3.5, can anyone help?
Does the Broadwell-E chip like the 6850k work out of the box with this X99 board or would i need a haswell chip first and then need to upgrade the bios or flash the bios?
hi . I to have a asus rampage v edition 10 and intel i7 6950x .your settings for 4ghz working well , nice one mate. Do u have a recommended setting for 4.4ghz or 4.5ghz .
thank you
So I have almost the exact same setup. Before I adjusted anything, it was reading 1200 mhz. Once I set everything like you, it was reading 4000 mhz. I loaded up the latest version of prime95 and it dropped to 3700 and temps never got above 73. However, once I shut it down, it instantly dropped back to 1200mhz. I saw that yours jumped right back to 4000. Do you have any idea what I am doing wrong. I am not an enthusiast, but need as much power as possible to shave some time off a process I am doing that is CPU intensive, and time sensitive.
hi! this settings works with i7 5960x?
hello dear can i install 3080ti for this set up ! 6850k , Rampage V Edition 10 32gb ram !
Hello again, Is there any hardware (and for overclock) difference about confidential edition and box edition for I7 6950X?
Meiner funktioniert nicht.sobald ich alles einstelle wie im video.will restarten.mein pc geht aus und dann kommt kein unterschied.. wieder im windows und dann geht er auch nur mit 3.2ghz.
can I use this same Oc for my 5960x using the same board as in the video?
+jhonny dead aren't the 2 240mm radiators bottlenecking the resevoirs?
Was that the delided one from the other video you did or is it a stock 6950X? Is 4000/3700 the ceiling you expect from air for the 10core?
no it was a normal 6950X. You can expect 4.1-4.4 with good cooling from these chips. The setting I showed is the basic setting so you can start testing more
Thanks. I am still not sure if i go 6900K or 6950X. May even skip again having a 3960@4700/6C running stable on water for years now. Thanks for the guide tough!
I would wait for Skylake-E which should be out next Computex and it will come with a new and more efficient PCH
Excellent vid, I want some advice if you can, I have this board, with a custom cooling loop, i7-6850k, I have two different sets of ram available g.skill trident z rgb 64gb ddr4-3466 (8gbx8) & 64gb ddr4-3200 (16gbx4) I want to push to the best combo possible, any advice?
Thanks
Maybe it is time we upgrade our cpu, mobo, and mem to 14900k ? :-) I lost my settings on my X99-A/USB3.1 mobo, and it just needs to be faster, so here I am...before I do an upgrade. How is your rig going? (year later)
Should I follow the same steps as I have the ROG x99 which is also a rog motherboard
Klasse Video mal wieder.
Ich hätte mal eine Frage, wie bekomme ich ddr-4 3600er RAM mit ner 5820k CPU zum laufen weil ich gehört habe die meisten CPUs lassen max. 2800er RAM zu!?
Und wie hoch kann man "in etwa" die Nordbridge Frequenz hoch machen?
Dankö.
Gabs da nicht Videos/Tests das mehr als 3000 nichts bringt? Also vom "more powa"-feeling mal abgesehen? ;)
Ja es soll nicht viel bringen, aber bei ArmA3 vlt. ein paar minimum. FPS.
I keep getting an overclock8ng failed and have to go back to default settings. I noticed one of my ram sticks isn't reading is this likely the problem? Otherwise the system runs ok stock i have i76950x and 64gb ram platinum 3330 but only reads 49152 mb of ram so could it be the ram causing the issue? Thanks great video
Can you let me know a good over clock speed for my i7 6850k? 32gb of gskillz ram liquid cooled 1200watt power supply rampage v motherboard
did you ever find one, same setup except 64gb ram, & psu.
@@Jimbo_1977 no and I’ve sold that build and built a way better machine since then now I’m running ryzen 5950x 128gb Corsair dom msi x570 creation motherboard evga 3090 ftw3 and it holds a steady 5.0-5.1
Did this to my computer ........ - i7 6950X. Computer crashed and won't reboot, bios flash didn't work, CPU must of friend.WARNING. *I USED THE SAME SETTINGS AS IN THE VIDEO.
I have same setup with g.skill 128gb 3200 cl14, and done same settings from the video but The processor is stuck on 3000mhz, the ram was ok at 3200, any idea what could be wrong?!
did you disable the Turbo Mode?
+der8auer never mind it worked 😝 how far were you able to push it beyond the 4 GHz?
On air 4.5 GHZ. And about 5.4 GHz on LN2 :)
Nice, would love to see a video of this ;)
what do you think about a factory corsair water-cooling setup, could you get close to 5ghz??
Hi 8auer,
wo liegt eigentlich die sichere Voltage-Obergrenze für die 6950x, um "Electromigration" und ähnliche Effekte im Zaum zu halten?
Ich bekommen demnächst meine 6950x und werde dann die von Dir beschriebenen Settings probieren (allerdings auf einem X99 Strix Gaming).
Danke für das interessant und hilfreiche Video!
Chris
Hey Chris! Bleib unter 1.35 vCore und dann ist alles gut :) Normalerweise solltest du damit auch etwas höher kommen als im Video. Die Kühlung muss aber entsprechend gut sein?
+der8auer ... Du hattest ja 1.20v eingestellt. Ist das für 4GHz und einen durchschnitts- 6950x ein typischer Wert? Ich dachte, man bräuchte dafür eher so um die 1.30V.
Die ganzen Einstellungen sollten ja auch auf dem Strix x99 funktionieren, oder muss ich noch etwas im Speziellen beachten?
Ich konnte bisher nur etwa 40-50 BW-E CPUs testen, aber davon hat der Großteil 4 GHz mit 1,20 Volt gemacht. Daher der Wert :) Funktioniert zu 100% auf dem Strix. Strix und R5E10 unterscheiden sich nur in ein paar features. Spannungsversorgung und BIOS sind identisch
+der8auer ... Super, danke für diese wertvollen Infos. CPU ist heute geliefert worden, morgen werde ich mich mal damit beschäftigen. Danke nochmals! Grüße, Chris
+der8auer Hi, bin jetzt dabei, Deine Settings auszuprobieren. Es scheint aber so, als ob mit diesen Einstellungen der Aida64 Streß-Test nicht sauber läuft (nutzt AVX). Crash nach etwa 10 Minuten. Was mach ich nun? Voltage hoch auf 1,3V? Bin für eine Vorschlag dankbar.
Does anyone know why a 6950x would not go over 3.5Ghz when coping his settings? I have the exact same chip and an edition 10 rog board, basically the same board. and when I copy his settings and run aida 64E, the clocks sit at 3.5. I cant get em higher. anybody able to help?
hexus.net/tech/news/cpu/122477-windows-10-kb4100347-update-breaks-broadwell-e-overclocking/
The solution that worked for me is ( from Microsoft forum)
Take security control of the file mcupdate_GenuineIntel.dll and then disable it by renaming it mcupdate_GenuineIntel.dll.disabled.
Reboot your PC and your Multiplicator will work as normal again.
answers.microsoft.com/en-us/windows/forum/windows_10-security/kb4100347-intel-microcode-updates-messes-with-cpu/51796b00-75cb-41fb-b587-0df7a1ed8349?page=3
5 GHz LN2 chip for Cinebench and wprime 1024, average or bad?
I have this same mb, an h115i cooler and a 6850K, 64 gb (8x8gb) Corsair Dominator Platinum 3000mhz DDR4. With the exception of the RAM XMP profile and the DDR4-3000 Setting, If I carbon copy all the other settings you made in the UEFI bios, should I theoretically be stable and good to go?
Adam Goddard any luck? Have exact same specs as you, would like to know how you oc. Thanks
I'm using a 6850k, I increased core to 45, did a voltage of 1.25 and cache voltage of 1.2,
Set the rest the same except my memory is xmp at 3200mhz, but my cpuz didn't show any improved values at all, even the bios page is still at standard frequencies. May I know why...?
Hi Gay
I followed all your steps. But my motherboard is a ASUS X99 Deluxe II.
I have a question. My motherboard have actived the Intel Speedstep.
With this configuration is better or worse to have it activated?.
Some there may be problem to have it activated?
Kind regards
ASUS MBs like overvoltage CPU VCCIO and VCCSA rails when overlclocking ram with XMP or auto voltages on this rails.
I have a 6800k, strix99 and hyperx 3200mhz. Whenever I try to overclock either manually or with Asus software. It fails to boot again and BIOS wont detect samsung 960 EVO my m.2 ssd systemdisk. Any idea whats wrong? It also only accepts me runnning ram at 3000mhz and not 3200mhz. Great videotutorial btw :)
On your CPU profile, you put 4000gHz XD. I think you meant to put 4000mHz.
bclk is 100mhz noob
hahaha :D
+Lars Vader lol I don't think you get it.
is that a bad joke or what 400o ghz very funny ?
Lars Vader 4000 GHz is a lot. Like no cpu has reached it before. Though 4000 MHz makes sense.
BTW 1GHz = 1000MHz.
I'm having a issue with this board. i cant get it to post using Corsair dominator 32gb 3200mhz (8x4) any advice?
Das Rampage V Edition 10 ist die größte Abzocke seit es Asus gibt!
wieso das?
A comparision between X99, Strix and Rampage would be nice. Like overclock on air, water and maybe ln2. Differences in bios/settings/stability...
600 ist viel zu viel. Nichtma nen 10 Gbits Netzwerk Onboard gibts dazu. Für bisschen bling, bling und ne 50 Cent Kunststoffplatte drauf zahle ich nicht 200 Euro Aufpreis zum Rampage v Extreme. Aber du kannst mir ja gerne erklären wieso das Board verdient hat mit 600 Euro eines der teuersten Consumer-Boards aller Zeiten zu sein
So frustrating. Stress tested for 5 hours
No issues. I was happy too fast. Upon reboot windows would not start unless I unplugged all USB devices. Went back to default (no overclocking) USB Ports work fine again.
James Bandes it might be power supply what is the psu and how much more voltage did you give it
Buzz Jump thanks I have it set to 4.2 running 1.21 volts. The USB Problem is because I had a Amazon dot echo plugged in. I unplugged it and everything is working great now
hey, thanks for the post. I have a irrelevant question but would be happy if anyone know the answer or reason, my water cooling system make me really nervous. I had to fill it just a bit to get it about 1cm upper than the incomin water tube every 2 or 3 weeks or it gets noisy bcs of the water level geting low it starts to making bubble and so much noise. Is it normal and the water cooling system should be filled in this short period of time?! I did t even overclocked my 6950x cpu that much just to 3.81 and a 560x radiator with 4 140 fans working just for the cpu!
You guys are mean :) Yes I mean 4000mHZ
OK i used the default settings and after a reboot the strange screen off problem is now gone !
I increased the 40 to 4.1 and its been running for 2 hours max temperature is 82.0 C and stable. I was hoping to go to 4.2 but when I increase my core voltage to 1.25 or 1.27 the temperature climbs to 96 C and it crashes.
Probably not much of a difference between 4.1 and 4.2 but would like to go to 4.2 if possible.
Thanks
Hello 8,
I have Density: 64GB (4x16GB) ram 2400 MHz
Just follow the given adjustments on bios?
What max. clock speeds do you expect on the 10-core with proper water cooling for a 24/7 build? 4GHz seems kind of low to be honest.
sure, it's just a basic setting, like I said :) With proper WC you can expect 4.2-4.4
Yup most advanced boards like Asus Rampage require at least some basic tweaking in BIOS since stuff like XMP never works at speeds as advertised. At least I haven't seen it. That's why you save a known stable baseline profile like was shown in this video and then can start tweaking more extreme overclocks from there!
HiI have ordered the Rampage V Edition 10 and will order an 6900K.What is the best frequencies i can reach? i saw on many websites than it can't reach 4.3Ghz.... i hope reaching 4.5/4.6Ghz with a EK Fullboard waterblock.Tell me what you think please.Regards.
that's not realistic unfortunately. 4.4 GHz at best
this settings works for a 6850k?
4.0GHz is a very mild OC for 6850k, you can take it further between 4.2-4.5 but remember every chip is different and you need to increase it just 100Mhz at a time and test before increasing
Hello'
first thank you for this Video. can i try this settings for this products
i have same cpu 6950X and asus rampage V Extreme ,Corsair dominator 2666MHz
thanks
nice, dass du musik von jonas benutzt!
hmm...
i have the 6900k with a water cooler Cirsair H105i.
Memory Kingstone HyperX 3200mhz.
I cant follow you because my system dont boot (monitor black) after i make the OC in the bios... so i think that my system is unsteable. so. ¿What i have to do different at you? memory OC is to much for mines?
Help please.
I HAVE THE SAME SPECS 95% the same... AND THIS DOES NOT WORK... PLZ HELP ME. - posted 10.10.19
It hangs and never posts... then I wait and wait to see if the CPU will OVERCLOCK to 4GHZ, when it fails, I get the "OVERCLOCKING FAILED!" message. And I have to press F1 for setup, where all my previous settings are now back to default, ram is 2133 and my 6950X is at 3000MHz, NOT the 4.0Ghz I wanted with the XMP 1 (profile)... help!
More Info:
I have the same specs with the 6950x... have the corsair dominator quad channel 3333 8gb x 8 =64gb of it... I put in the EXACT settings and the computer restarts-COLD RESTART-and when it does start up, the code in the corner stays at " 6d " -at least I think that's it. I have no idea what that means, it cycles from that to 60 and back to that 6d or is it saying 'bd'... not sure what the code is... JUST KNOW IT DOESN'T WORK. There is one yellow led lit up and blinking next to the code, it is like it wants to start up but something is stopping it and it repeats the cycle of the codes going from '60-69' or' 60-bd' or '60-6d'... Once it does that for a while, the computer completely restarts and loads the old settings.
Now I have BIOS 0903... do I have to upgrade to have it working?
ANYONE HERE? HELP ME PLZ! I WANT the hardware to run to get the money out of what I spent for it...bid deal to me. Thank you KINDLY. I APPRECIATE ANY FUTURE HELP.
1 idea, instead of 8 sticks of RAM, should I just use 4 and put them in only 1 quad channel slots? 8gb x 4 instead of 8gb x 8... less memory but it might do something... NOT SURE... HELP OB1... ANYONE.
Ah it may be a bit late but looks like that is a RAM issue. First try updating your bios and see if the error code is the same, and if that doesnt work try turning off xmp and try the 4ghz clock. That's it really the error code is on about DXE initialization which means its trying to recognize your ram which could lead to why your xmp profiles aren't functioning properly
@@MegaKayway could you give me all the settings you know of? for faster ram, oc, and faster cpu, oc, separate... and also settings with everything together... I have the newest bios... this is corsair dominators... real nice ram on the QRM-the registered manufacturers that make ram exactly working for this MB... I am curious what everyone here has their setting that work so well... also fastest ram used, make model... all that good stuff... hook me up...for 5 years I never had this baby at 4ghz... it always does something funky after the auto settings... i'll tryp xmp... but I doubt it.
Let me know if that error code had anything to do with a GROUND ISSUE? thanks.
@@MegaKayway the ram was recognized... CMD -3333mhz version quad core 32gb and I have 2 of them to fill the 8 slots for 64 total... xmp option sees it fine... I will do the 4.0 without xmp test now. I just have "6d" sitting on the bios output code screen on the motherboard... 6d and a yellow is flashing... meaning what one of the modules is bad?
can I still run 7 modules and get full speeds or no? or it doesn't matter if it just one bad module, take it out and try again? with xmp? let me know. thanks and I never got an email about you responding... THANK YOU SO MUCH! lets see if this works.
and I'm running on bios 2102... you have bios from 2016... I have 2019 bios... let me know
tried without xmp and nothing... just sat off not booting with the 6d and yellow led flashing... I never got my 6950x higher than 3.0ghz or have my 64gb of ram ever go past 1333... I even have air conditioning and water cooling on the units... it runs at 25-30 degrees C... but as soon as I put it with any of your settings it just sits there and returns to the slow speeds... I think the ram module is broken... I'm trying to make a cancer movie and having ram that works really matters... is there anyone that may help? plz. I can only afford this old computer to do the 4K RAW editing on... and After Effects... and slow video cards because of the super costs. This is for my father, he has the cancer, something that was given to him by bad doctors. PLEASE HELP.
I have same board with 6800K - whenever my cpu is hitting more than 70c it is restarting. Finally i fixed this in the settings by changing the the cpu max temperature manually to 95
I keep getting a multiplier of 12 and my cpu is clocked between 12 and 3000 despite following this guide. any ideas for fixes?
I follow the same steps and my Pc os not opening windows...!! 😑 64gb dom plat Of ram makes any diferences..???
Is this motherboard compatible with EK-FB KIT ASUS R5E - Acetal+Nickel (Original CSQ) water cooling sistem
i7 5820k or i7 6800k ?
I dunno which one I should pick. D:
Schafft der Noctua D-15 4Ghz beim 6800k oder wird das schon zu heiß?
Der NH-D15 packt das :) Wenn du jetzt upgraden willst dann nimm den 6800K
Ah super, dann wird es wohl ein 6800k in Kombination mit dem Noctua D-15. Hast du eventuell noch eine Mainboard Empfehlung unter 500€, Herstellungsjahr 2016. Ist die letzte Frage, die sich mir noch stellt, dann kann ich die Bestellung fertig machen. ^^
Das ASUS Rampage V Edition 10 ist schon toll, aber der Preis dafür ist gesalzen. Ich möchte nur moderat Übertakten und keine neuen Rekorde aufstellen. :) Fällt dir spontan eins mit guten Preis/Leistungsverhältnis ein? Habe jetzt keine besonderen Wünsche, außer das es von 2016 sein sollte. ^^
hi just got me a 6950X and was wondering if you have taken it past 4.0 and would you think of doing a video on that ?
yea up to 4.4 GHz 24/7 stable. Same settings just CPU Core Ratio to 44 and CPU Core Voltage to 1.34. But ofc that depends on the individual CPU quality
good to hear I will have a 4 fan rad on it... thanks for the reply.
thanks just did it today to 4.4 works perfect, one core at 73 and the rest at about 59-71-
Does the Klevv Cras memory work with this board? I notice in the video you switch to g skill memory during the over clock.
Because the G.Skill memory is better for OC :) But Klevv works fine, too
Klevv uses Hynix MFR ICs and G.Skill Samsung ICs
Thanks for the info! Let me know if the old Rampage V water blocks fit on this new board.