See I got this Garmin eld as soon I plug let it book two check lights and 2 codes under CGW. I took it out and the codes aren’t there anymore but one check engine light remains. Help
Did you ever find out what your codes were for? I’ve been dealing with the same codes for the last few months they are for the after treatment system and specifically for DEF injection, I have a 2019 Cascadia as well and I’ve spent just about $20,000 trying to fix these codes
On the right hand side of the steering wheel there is a button with squares overlapping, when you are in the main screen, press it and a menu to increase it will appear in the main screen, with the arrows up and down, on the left of the steering wheel, you can control the engine speed at idle. Thanks for watching and I hope this information help you.
First: is it the new clutch the same as the old one you removed? Sometimes there are slight differences between clutches make sure about it. Second: did you calibrate the new clutch? DDDL 8 software is required for this step. Otherwise, the new clutch will not work properly. I hope this information help you. Thanks for watching.
Hello I have a orange check engine light on my 2020 Freightliner Cascadia right now and there is a fault code under the ACM can you tell me what's the issue if I can give you the code number?
Thank you sir.. gracias...lm looking to change settings.. 2019 cascadia DD15, DT12. The trans is only on economy mode.. l only get 7.5 mpg. Midroof trk pulling light flatbed loads.. Also when the truck switches to E coast the motor idles low and oil pressure drops to 15psi. Is that ok? I'll be in the 45-65mph range.
Usually, if you have this dashboard (newest cascadia), you can dig in to find out a basic information about the fault code. Over the internet, you might find a bit about it, but in order to know exactly the issue, you are going to need the DDL software. This is a diagnostic tool need it in order to find out why the Check Engine is On or MIL (Malfunction Information Light) is on. I hope this help you with your matter. To know a code just by the SPN, FMI or other methods is hard because there are thousands relate to it.
I might be something relate it radar or sensor angle, those problems might be solve with a software update from Freightliner dealership. Thanks for watching.
You CANNOT reset fault codes with the ICU (Instrument Cluster Unit) or Dashboard. You need the DDDL (Detroit Diesel Diagnostic Link) software or an aftermarket diesel software to clear the faults stored in the ECM.
Your truck has idle shutdown active. If you want to idle, you need to take your vehicle with a technician with DDDL software to remove that feature. Thanks for watching.
The MCM codes you need the Detroit Diesel Diagnostic Link (DDDL software) to know exactly the codes. About the ABS code if you had performed a brake job recently, perhaps one of the ABS sensor is not in place properly. Make sure your technician check all the brakes to see which is out place. Hope this help. Thanks for watching.
I got engine light and its showing sign in MCM and showing fault waring symbol sign but when i click on it it say no fault found. And i got solid yellow engine light. What wrong then if its not showing any code ??
Usually, inactive codes store in the MCM memory, but those codes cannot be check directly from the instrument cluster screen, even when there is a warning sign from it. if your truck MIL (Malfunction Information Light) stays on for few days, you might need to take a repair shop to connect the proper diagnostic tool. Thanks for watching and I hope this help you.
CPC (Common Powertrain Controller) codes are relate it to the communication between ECM, TCM and others modules. Sometimes, wires can be the cause and even just the bad weather, for example: Snow conditions or high heat temperatures. Either way, it is really unlikely that you by yourself can fix it without the Software tool (DDDL). If problems persist, you should take it to the nearest shop to let them check the fault codes. I hope this help you and thanks for watching.
George From the Bronx do you know how to by pass radar I switch cab the frame has radar and wire to the cab but cab don’t have a conection and I don’t need this shit and cruise control stops every 5minuts
![COLOMBIA vs. CHILE [4-0] | RESUMEN | ELIMINATORIAS SUDAMERICANAS | FECHA 10](http://i.ytimg.com/vi/TDjN4W3yy1k/mqdefault.jpg)
Very helpful and informative video.
Good job 👍
It was an excellent 👌 video. Thanks
Thank you Very much !
Very helpful thanks a lot
End off the code White⚪️ and blue🔵 point, what’s that mean? thanks🙏
See I got this Garmin eld as soon I plug let it book two check lights and 2 codes under CGW.
I took it out and the codes aren’t there anymore but one check engine light remains. Help
CGW, j1939-250k comms error serice vehicle , whats that mean?
I am getting HVCR is it serious issue ?
Same
I have 2 orange engine light on. Egr some mechanic said.. any recommendation?
Hello, in my 2019 Cascadia engine light on and off. Active shows 0. However I found on ACM fault code 520372, 520371. What can be that? Thank you
Update
Did you ever find out what your codes were for? I’ve been dealing with the same codes for the last few months they are for the after treatment system and specifically for DEF injection, I have a 2019 Cascadia as well and I’ve spent just about $20,000 trying to fix these codes
How to set 5443 15 fault code...it also stuck on manual mode
I have a 2019 cascadia I don't have apu so i idle my truck - how can I increase my rpm when I am parked?
On the right hand side of the steering wheel there is a button with squares overlapping, when you are in the main screen, press it and a menu to increase it will appear in the main screen, with the arrows up and down, on the left of the steering wheel, you can control the engine speed at idle. Thanks for watching and I hope this information help you.
How do you remove the distance warning alert because I've been trying to find it and I dont get it it's annoying
Notice to its the only thing that works. Everything else fails
I replaced a clutch on a cascadia 2017 and it’s stuck on manual and won’t start
Telling me to switch to neutral when on neutral
First: is it the new clutch the same as the old one you removed? Sometimes there are slight differences between clutches make sure about it.
Second: did you calibrate the new clutch? DDDL 8 software is required for this step. Otherwise, the new clutch will not work properly. I hope this information help you. Thanks for watching.
Hello I have a orange check engine light on my 2020 Freightliner Cascadia right now and there is a fault code under the ACM can you tell me what's the issue if I can give you the code number?
Update
How can I fix the dome light in the cab because is on & of automatically
Just break it
No alerts show but I have code on ACM 520349 14..what is can be
Thank you sir.. gracias...lm looking to change settings..
2019 cascadia DD15, DT12. The trans is only on economy mode.. l only get 7.5 mpg.
Midroof trk pulling light flatbed loads..
Also when the truck switches to E coast the motor idles low and oil pressure drops to 15psi. Is that ok?
I'll be in the 45-65mph range.
Do you know what CPC codes 521001 and 521002 mean?
Usually, if you have this dashboard (newest cascadia), you can dig in to find out a basic information about the fault code. Over the internet, you might find a bit about it, but in order to know exactly the issue, you are going to need the DDL software. This is a diagnostic tool need it in order to find out why the Check Engine is On or MIL (Malfunction Information Light) is on. I hope this help you with your matter. To know a code just by the SPN, FMI or other methods is hard because there are thousands relate to it.
My 2021 freightliner has a triangle next to srrr in the diagnostics. Often it sets off my abs tcu disables my adaptive cruise control
I might be something relate it radar or sensor angle, those problems might be solve with a software update from Freightliner dealership. Thanks for watching.
How do you reset the fault codes on a 2020 Freightliner Cascadia?
You CANNOT reset fault codes with the ICU (Instrument Cluster Unit) or Dashboard. You need the DDDL (Detroit Diesel Diagnostic Link) software or an aftermarket diesel software to clear the faults stored in the ECM.
Hvcr which one
Hi dear my Engine shutting off when I go to sleep please tell me what shoud I do for that I have same screen your truck
Your truck has idle shutdown active. If you want to idle, you need to take your vehicle with a technician with DDDL software to remove that feature. Thanks for watching.
I have mcm problem 171-3 and 171-19. And abs 790-1 check wheel speed sensor b airgap
The MCM codes you need the Detroit Diesel Diagnostic Link (DDDL software) to know exactly the codes. About the ABS code if you had performed a brake job recently, perhaps one of the ABS sensor is not in place properly. Make sure your technician check all the brakes to see which is out place. Hope this help. Thanks for watching.
I got engine light and its showing sign in MCM and showing fault waring symbol sign but when i click on it it say no fault found. And i got solid yellow engine light. What wrong then if its not showing any code ??
Usually, inactive codes store in the MCM memory, but those codes cannot be check directly from the instrument cluster screen, even when there is a warning sign from it. if your truck MIL (Malfunction Information Light) stays on for few days, you might need to take a repair shop to connect the proper diagnostic tool. Thanks for watching and I hope this help you.
@@LetstalkDIESEL hi thanks for replying back the engine light was gone after 2,3 hours and its not showing up again.
My truck stopped and it was showing the cpc how do I fix it
CPC (Common Powertrain Controller) codes are relate it to the communication between ECM, TCM and others modules. Sometimes, wires can be the cause and even just the bad weather, for example: Snow conditions or high heat temperatures. Either way, it is really unlikely that you by yourself can fix it without the Software tool (DDDL). If problems persist, you should take it to the nearest shop to let them check the fault codes. I hope this help you and thanks for watching.
George From the Bronx do you know how to by pass radar I switch cab the frame has radar and wire to the cab but cab don’t have a conection and I don’t need this shit and cruise control stops every 5minuts
@@LetstalkDIESEL hey bro i got same issues cpc. Truck stopped . What causes the reason? And how to fix?
@@gurjotsingh6056 Are you able to fix it coz i have the same issue.
Why or what can I do if my hood latch says it unlatched?
Hello where do l view my engine hours?