Installation Guide: Monorim V2 & V3 Suspension Upgrade for Xiaomi Scooter
HTML-код
- Опубликовано: 17 окт 2024
- This video shows you how to install the Monorim V2 and V3 Suspension on your Xiaomi M365, M365 Pro, Pro 2, 1S, Essential.
Note: The V3 has the mandatory included mudguard holder that must be fitted on the mudguard as instructed by brand guidelines.
EDIT: At 1:06 As of September 2020, the kit comes with a red and blue spring. The red spring has a max capacity of 275lbs. If you are a light rider, we advise you use the blue spring with 220lbs max capacity for the best ride.
Information:
00:05 Introduction
0:48 Package Contents
01:56 Changing Spring/Load
02:27: This silver spacer is no longer included, as the spring length has been extended.
Preparation:
03:41 Removing Plastic Trim
05:47 Removing Front Wheel
07:15 Removing Center Screw + Steering Pole
08:52 Removing Rings
10:45 Ring Order (Removed)
Installation:
10:52 V2 Suspension Install
15:09 Adding Steering Pole + Center Screw
16:37 Moving Mudguard From Old To New Fork
20:44 Adding Front Wheel
22:12 Fixing Bolts/Zero Wobble
24:35 Adding Plastic Trim
28:59 Demonstration - Enjoy it!
Buy it here: www.amazon.com...
Worldwide 5-7 day shipping for just +29USD!
The were slight changes in mounting M1 V4 with regulation spring for Xiaomi Scooter 3 2022, but it was very helpful :)
Very good tutorial: BUT do not use the original bolt for the handle bar. It's way too long and it will bend the upper axle of the monorim. Just use the one in the kit, that is longer, but shorter than original with about 1 cm. I've screwed so hard the original that bent the axle and in the end the screw broke. It was a nightmare removing the remaining piece of the bolt, and because the axle was bend, I just gave up and cut everything with a bolt cutter and then bought a new monorim kit and did a second install by the book. Luckly the 2nd was on sale for 50 Dollars, and it was a V3 with the fender support piece. After all, it was still worth the time and money.
Thanks, you were right!
I measured to where the bolt would hit and it was way too long, the one provided fit perfectly.
Thanks for saving my ass!!!
What bolt?
@@killiandark6927 the bolt that holds the fork in place
Thank you so much! Just installed. I put solid tires on my m365 a few months back and the ride has been pretty harsh on Chicago streets. So glad to have some give on the front wheel. Less handlebar shudder.
sir i think you drop one BB on 11:43 part. I hope u placed it back after making the video. You missed 1 there. thank you for making this in-depth installation. It helps a lot since I am planning to buy 1.
I did not even notice that! Thank you for bringing that to my attention! :)
By following this video you absolutely can't go wrong. Thank you for making this tutorial.
you've lost a metal ball on the ballbearing wheel @ 11:43...do you think there is a problem to install on a 10 inch wheels setup ? great video, thanks !
Hello. What do you have at the very bottom part of the stem? Only the bearing? Or with 1 or 2 washer? Thanks
Hey, please do a video with the V2 Pro (adjustable spring). Really would be helpful, am about to buy it. Also would be good to show how to install it with the VERY IMPORTANT safety attachment that stops the fender from touching the front wheel.
Just fitted this to a AOVO ProM365, a few tense moments, but done. Great video
did it go in perfectly?
I tried it on mine but the handlebar's main big tube still is able to "turn" if I try to turn the handlebars over their turning point. I tightened every single screw that holds it in place, and it looks like it is correctly assembled...
@@TheTTax I had that issue too, after a while make sure the top 2 silver bolts are TIGHT, i used a key with a wrench on as leverage, if that fails you could shim the inside
@@nigelnithercott2592 Thank you!! I tightened it, and also the central screw inside the locking mechanism, and it worked. it's fixed now.
Thank you so much :)
Does the suspension work for Xiaomi Mi 3 ? The monorim site says it does but i have problems installing
Same
Thank you so much for making this video, very clear and precise. Life savior for newbie like me...
nice video , i really like it
but you lost one ball from the bearing :D or it looks like that
Very detailed video. Thanks! I’m waiting for mine to arrive. Now, question, it seems to me that front mudguard was still loose when you assembled the front wheel. It can’t be fastened better, stronger or....? Also what is that red lack you said it is good to put it on 2 wheel screws? Thanks!
Hi buddy. After I install it the Scooter don't keep in the way. It go slowly to the left or right. Do you have any suggestions ?
Thx by advance
Thanxs mate . Very clear video . I am going to get it myself soon .
Super Installation Guide 👍
Great video, thanks so much! Quick question though, which covers are you using for the wheel bolts? The right one fits fine but the left doesn’t sit flush because of the bolt :(
If you wish to upgrade the front shock on this to a dual chamber air suspension shock what is the minimum size shock that Monorin recommends? Original shock ( with spring inside) in the kit is 150 mm fully extended, measured from centre of top mounting eye to centre of bottom mounting eye . Air shocks have a fatter /wider canister body to them than original spring shock which may control what size shock you can fit. Any body fitted one ( KS A5 RR1 logo one for instance) and has advice please?
you ever find out if you can upgrade the shock. i wanted to upgrade mine as well to something beefier. it looks kind of like the mountain bike components with a custom frame.
Someone help man when u tighten the centre bolt the one inside the handle bare doesn’t move it’s too tight and when I loosen it it shakes
Very good demonstration. One of the best on the net! Thank you!!!
I have a big improvement while riding on bumpy surfaces. Such a relieve for my wrists... Would be so nice if there was something like that for a rear wheel.
One question. In that small plastic package with extra screws and rubber/metal washers for mud guard from Monorim there is always left small metal bearing 00:57. Any idea what is that for?
I’ve parts left over from V4 is there tutorial for V4 anywhere
Great video you explained it really good , thank you 👍🏻
really great video, totally agree with you, the video the monorim guys sent is far too fast. I really appreciate you doing this video.
I just have a question if you don't mind answering. The yellow and blue spring. Is it possible at all to change the screws over after the installation? So if I install the blue one and decide its not for me, and want the yellow one in. Will I have to do a full strip down again, or is it easily changed after the suspension kit goes on. Hope you can help
Thanks
Mike in the UK
Hi Michael. Yes, what you need to do is to loosen the two bolts that hold the top of the metal housing. If you loosen those two, you can unscrew the cap and lift it up to expose the spring. All of this can be done without uninstalling the suspension kit itself. I hope that makes sense!
Best regards,
Nikolaj C
NASH Team
@@nikolajchristensen1009 brilliant, thank you for taking the time to reply
If you send me your email, I can send you a picture to explain it better than I can by words :)
Hi what size spanner / wrench are you using please ?
HI does ur handle wobble after installating? Mine when shake it wobble the handle bar?
Did you ever fix this I have the same problem
Whats the difference between this ans the one version that has the shock exposed??
Thank you my friend, it was very helpful.
Do I cut the center bolt to stop it damaging the center bar which pushes through holding the suspension on? The Bolt is too long!
Got the same problem. The center bar is totally bent right now.
Use the longest black bolt of the 2. Not the one for the mudguard
after installing the steering wheel is not in line with the wheel, could someone tell me how to fix it?
Is this compatible with the new version, Xiaomi Scooter 1s?
Hi Alexis. Yes, the Monorim V2 is also compatible with the newer models of the Xiaomi scooter, hereunder the models 1S, Pro 2, Essential. I hope that clarifies!
what is the difference between v2 and v4 ?
Great video buddy! I've just ordered this and some honeycomb tyre's as I've got a puncher and really cba to keep changing it 🙈 gonna change them both together. The mud guard looked a bitch lol
I camt even get the plastic gard screws out its as if the tools dont fit
Very good informations, I thank you Sir. ❤️
Nice video. 👍
Thanks for video
the screw that screws into the stem wont go deep enough for me the black washer is just loose in there while the stem is atached
Thank you!
Hi do you know what this screw does? your video at 9:01 minute: ruclips.net/video/dICeg1upIcg/видео.html (EDIT: you didn't put this screw back?)
You forgot to put the screw from 8:54 minute back on.
Wtf, how long are the fkg scrues dude?
The problem with this KIT (V2 and V3 included) is that the mudguard rotates at stronger vibrations even if it is tightened to the maximum. I had to glue it in place with hot glue so it won't move anymore... That's one big f**k up from the manufacturer/designer.
Soy el único que se le queda con orgura?
you should put grease on the bearings i you are going to do a mechanical video do it properly please
I think it's common sense... plus every video is pretty much edited removing (I would say) obvious things...