How To Replace the Axle Bearings on a Yamaha Raptor 700
HTML-код
- Опубликовано: 16 июл 2024
- Shop Now | Yamaha Raptor 700 Axle Bearing Replacement www.rockymountainatvmc.com/Sa...
Inspecting and replacing your rear axle and axle bearings is a part of maintenance that should be done regularly to ensure that your ATV is running properly. If your feel slop in your rear axle, your machine is most likely in desperate need of axle bearing replacement. In this video Charles shows how to replace the axle bearings on a 2008 Yamaha Raptor 700, but these steps will be very similar for all Raptor 700's.
Check out www.rockymountainatvmc.com/Sa... for all your parts, apparel, and accessories!
Click Here To Subscribe To Our Channel!
/ @rmatvmc
Follow Rocky Mountain ATV/MC On Social Media!
FACEBOOK: rmatvmc?utm_...
INSTAGRAM: rmatvmc?ut...
TWITTER: RMatvmc?... Хобби
Awesome! More Raptor content! 💪🏻
I love this and all RMC videos
GREAT video! Easy decision to support RM ATV when they are continually putting out videos like this. Just did this job, no issues!
Thank you so much for the support! We're glad this video helped make the job easy.
Awesome video, very helpful . [ NZ ]
Nice, I just got a carrier from RM last week. My 06 brake hub is seized solid on axle though, and no amount of penetrating oil, heat, or hammering seems to want to free it up. As such, I liked when you cut the footage to sliding it off by hand 😂
I thought I would die of old age before I got it off, we will just see if I need a new brake disc now lol
Great video👍
Thanks for listing the torques specs on everything so thorough. You guys make great video's.
Thanks watched this video about a million times haha very helpful
You're welcome! Glad the video helped out.
Thank you
Was wondering, upon removal you removed an oring off the axle on the brake disc side but on installation you referenced an oring on the sprocket side while not putting the oring back on the axle on the brake disc side? I don’t seem to have an oring on the exterior of the sprocket side
Hi can you also put the upgraded 2 bearing in the carrier instead of the 4 bearings in a raptor 700r 2011 ? Thanks
Thankyou
How did your carrier berring come off the axle I’m beating the end of the axle but the berring isn’t separating from the axle
Привет! Перед установкой тормозного диска ты не поставил резиновое уплотнительное кольцо. Или ты просто не показал это на видео?
I can't get the axle completely in there's always a 1inch gap snd I've tried to force it in but it just doesn't go. HELP
Good video how often you supposed to do this I put on an hour meter the day I got my ATV I got a 2018 Raptor 700R I got about a hundred hours on there 99.3 to be exact what do you think I do go in water sometimes
Do it when you feel play in the axle
Didn’t put the o rings back on the axle ?
hi.. can you tell me what type of grease you use ? thanks!
Put any grease on it. Anything is better than nothing!
What snap ring pliers are you using ? I can’t find a pair big/strong enough to take that snap ring off. Thanks in advance!
No kidding I'm in the same situation . Putting it back on is worse !
Get it open a little bit and get some screwdrivers
you never showed how to grease the carrier bearing housing and show how to and sloppy that sleeve is inside there so can you please tell me why that sleeve is just loose and moving around in there and does the grease stop that
what about greesing up your bearing carrier
Yes, make sure you are greasing it as well, to help the rust and removal process later in the future.
I don't understand the minute 8:40. Help mee!
i swear i just watched him put 2 bearings in one end? that would be 3 bearings ?
Your not the only one I seen it to but isn't it only 2 one on each side ??
There is two on each side