How to test a power window switch/motor (1985-2001 Toyota)

Поделиться
HTML-код
  • Опубликовано: 2 окт 2024
  • 1992 Toyota Camry Power Window Troubleshooting.
    The testing procedure shown in this video can be applied to any reverse polarity DC electric motor. This car has an Auto Down power window circuit that is used on many different models.
    Related videos
    How to test and fix a PGM-FI main relay - Honda/Acura
    • How to test and fix a ...
    How to identify a bad main relay on a Honda (PGM-FI)
    • How to identify a bad ...
    Tools used
    Power Probe IV
    www.aeswave.co...
    Power Probe Lead Set (PPLS01)
    www.aeswave.co...
    AES' Electronics Accupuncture Probes www.aeswave.co...
    OTC 3633 Mini Circuit Tester
    www.jbtoolsale...
    Related videos
    Auto Down Power Window Circuit Operation and Troubleshooting
    • Video
    For more information on this topic, I have written a “field manual” called Engine Performance Diagnostics which is available at www.scannerdanner.com as an eBook or paper book.
    Want even more diagnostic training? Whether you are a DIY trying to fix your own car, someone looking to become an auto technician, or a current auto technician that wants to get more into diagnostics, subscribe to ScannerDanner Premium www.scannerdan... There is a 14 day free trial.
    On ScannerDanner Premium I will bring you right into my classroom at Rosedale Technical College. You will find page for page lectures taken right from my book as well as exclusive classroom type case studies. What is so special about these classroom case studies? I pull live problem vehicles directly into my classroom and we troubleshoot them in real time, using and applying the theory and testing procedures we learn during the classroom lectures. There is no better on-line training of how to troubleshoot automotive electrical and electronics systems anywhere!
    Disclaimer:
    Due to factors beyond the control of ScannerDanner LLC, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. ScannerDanner LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. ScannerDanner LLC recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of ScannerDanner LLC, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not ScannerDanner LLC.

Комментарии • 215

  • @shanebrunette4399
    @shanebrunette4399 7 лет назад +5

    where do I get your book

    • @ScannerDanner
      @ScannerDanner  7 лет назад +4

      Through my website at www.scannerdanner.com
      It is available as an eBook or paper book.
      Thank you!

    • @smokelikeahippi4538
      @smokelikeahippi4538 7 лет назад

      ScannerDanner I am having s major issue with my 2000 blazer. I'd appreciate it if you'd contact me by email. my email is louievilleslugger95@gmail.com I just need help troubleshooting. any advice would be greatly appreciated

    • @ScannerDanner
      @ScannerDanner  7 лет назад +3

      I'm having trouble keeping up with these types of requests.
      It is becoming more and more difficult to answer questions here. I have 90,000 people asking me for help now. So I have created a forum to help you guys better. It is free to join and we can exchange pictures, wiring diagrams and waveforms if needed to help guide you through the process of troubleshooting your vehicle. Thank you so much! Hope to see you there.
      Paul Danner (ScannerDanner)
      www.scannerdanner.com/forum/post-your-repair-questions-here.html

    • @ironmike742
      @ironmike742 3 года назад +1

      @@ScannerDanner that's what you get when you're a problem solver. I work at a Ford dealership and have 26 years in the field. My phone rings off the hook from people needing help. I always try to pay it forward and help because without a lot of people's help I wouldn't be where I am today but sometimes it becomes overwhelming. It's a double edged sword but the good Lord will never give us more than we can handle.

    • @ironmike742
      @ironmike742 3 года назад

      @@ScannerDanner also when I am unsure of the voltage reading on a window circuit since I have the master window switch right there in my hand I'll test a working circuit from another window. Testing a known good one is something you teach and preach all the time. I have learned alot from you sir. We are a dying breed. A high percentage of TECHNICIANS in the field are parts changers. Keep up the good work and just know that you are appreciated.

  • @joeandgod1
    @joeandgod1 7 лет назад +8

    I've used the power probe, the load pro, etc... After everything, nothing beats the simplicity and efficiency of the mighty "TEST LIGHT".

    • @ScannerDanner
      @ScannerDanner  7 лет назад

      agree, the test light would have been my tool of choice had it not been for the fact that I needed to manually get that window up.

    • @AGuysGarage
      @AGuysGarage 7 лет назад

      Couldn't you use a DMM and just leave everything hooked up one way? When it reverses it will just read negative voltage. Easy peezy. Unless i am missing something. /shrug, love my fluke dmm with super sharp spear you in the eyeball probes

    • @joeandgod1
      @joeandgod1 7 лет назад

      I think that's another way of doing it. The only problem with the volt meter is that it doesn't "load" the circuit like the test light does. So the test light checks for ground and power and loads the circuit at the same time.

    • @AGuysGarage
      @AGuysGarage 7 лет назад

      keep the motor in circuit and it supplies the load. meter just tells you if there is Voltage in both directions. Sort of a quick and dirty test. If it goes down, u get 12V so up without changing anything should be -12v because the grounds swap. if it remains 0 the motor is good because it went down, only thing left is switch / solder on the switch board. or a broken wire for up. or the module itself /shrug to each their own. once one gets the feel for it, it is shocking what you can find out just with a simple diode check setting.
      "use it as a short detector" I have been in electronics repair for a very long time, i guess i am just really comfy with the DMM plus it is relatively cheap compared to fancy stuff. the window circuit on my pathfinder is a bit strange, when you close the switch it grounds on a different module entirely. pretty simple really, hit the button, completes circuit and window moves. used it to install my "momentary switch 2 wire door popper" never call the locksmith again or worry about a magnetic key box letting go when u hit a pot hole or a good bump.

  • @KingBaconMonger
    @KingBaconMonger 9 месяцев назад

    Dang!! I was trying to figure out on a 2013 CRV: Master window switch? Passenger window switch? Motor? Regulator? I did what you said, I yanked the button on the master switch up and down, nothing, did it again, did it again, mashed it down - THE WINDOW MOVED. It's something with the master window switch. I can replace that, no problem. YOU ARE A GENIUS! Thank you, ScannerDanner!

  • @stevenknaub55
    @stevenknaub55 21 день назад

    I’m no electrical engineer, but I believe when you press the auto down feature, the resistor, works in conjunction with the circuit board to maintain the physical position of the switch you activated until the window meets the end of travel at which time the current exceeds limitations, and the board then releases its control over the mechanical switch and the switch returns to the neutral ground position

  • @stevenhzoll7057
    @stevenhzoll7057 7 лет назад +2

    I could never wrap my head around a Power Probe and I know how they allow you to supply batt+ and - to the circuit under test . Yes the incandescent test light (scope on a rope SMA) is still my go to tool and if you know the current carrying capability of the circuit a sealed beam headlight makes a nice load.
    I agree that the auto down feature cannot function as wired in the Mitchel diagram.
    Keep up the great work between you, Eric O and Ivan I might just start to figure some of this stuff out Thanks

    • @ScannerDanner
      @ScannerDanner  7 лет назад

      Nice, thank you! I thought maybe I was going crazy with that diagram.

  • @tecnaman9097
    @tecnaman9097 7 лет назад

    Paul from my experience attempting to fix taxi cab window switches over many years it just ain't worth the trouble.! I used to bodger them using a points file (remember them) to clean the contacts but it always failed. Only did this if I didn't have one to go. Man, I know what you mean when you say patience is needed!

  • @leifsimmons2464
    @leifsimmons2464 7 лет назад +2

    I believe the resistor is a current sense resistor. When the motor stalls, current will increase and the voltage drop over the resistor will increase. The "solid state" box in your diagram will be able to detect the voltage difference between "true" ground and motor ground and stop feeding power to the motor.

  • @freddyflores6412
    @freddyflores6412 7 лет назад +2

    I always just use a multimeter to diagnose window problems . Just back probe both wires at the same time and then push switch either way . Then look at your voltage reading .

    • @ScannerDanner
      @ScannerDanner  7 лет назад

      Definitely multiple ways to troubleshoot these. Thanks for the comment.

  • @jpintrick84
    @jpintrick84 7 лет назад +1

    you ever run into a broken wire in the door jam I run into that all the time wear the harness goes into the door the wires Flex a lot and end up breaking inside the casing talk on them a little bit the broken one will stretch just fix that on my Ford Explorer only took 2 days LOL

  • @nemanjadzombic6101
    @nemanjadzombic6101 6 лет назад +1

    On 500 likes statistically there has to be certain number of dislikes. But 31 is a bit to much. I guess people who dislike, they do that because they were thinking this is gonna be simple fix. But whatching it and having difficulties understanding it, make them angry.
    I can't possibly see any other reason to dislike this video. It would be really interesting to read explanation for hiting dislike button.
    I like simple solutions but if there is no one, what then? Parts changing - You're definitely on the wrong channel and that's not autor's fault.

  • @johnkaplanian
    @johnkaplanian 7 лет назад

    Dear Mr. Paul, maybe sometimes such contacts that resembles old distributors contact points can be cleaned well using sand paper / FYI and thanks you indeed for all these wonderful videos.

  • @nickayivor8432
    @nickayivor8432 2 года назад

    SUBSTANTIAL Sir ScannerDanner
    Thank you 👍
    Sir ScannerDanner
    From Nick Ayivor from London England UK 🇬🇧

  • @tylermelendez
    @tylermelendez 7 лет назад +3

    Here is a link for a 2000 Corolla genuine Toyota PWMS diagram. Much more accurate and a tad bit more complicated.
    drive.google.com/open?id=0B1DZbsT-6zx_NmxzQUZwZFJ2Rzg

  • @josealzurut2956
    @josealzurut2956 2 года назад

    Hi good video, I have the same problem with the driver´s windows (IS there a fusible or relay to check it?. I cleaned all master swithc window

  • @rhkips
    @rhkips 7 лет назад +4

    No doubt Pete's a sharp cookie! I just worry that I see so many cars you troubleshoot there with dead batteries. Does Pete feed off DC electricity, and just him being around drains all the nearby batteries? ;D
    Great video, Paul! The confusion with the Power Probe turned into an excellent teaching opportunity for you, and an excellent learning opportunity for us. Total win! Though, you really should carry around a sheet of 120-grit sandpaper in your glovebox; works great for cleaning dead contacts and a myriad of other things! 120-grit is the WD-40 of sandpaper. :D

    • @ScannerDanner
      @ScannerDanner  7 лет назад +2

      I'm thinking the same thing! I always have a dead battery when I'm down there.
      Thanks for the positive reinforcement. I hesitated to upload this video.
      And thanks for the tips!

    • @markchidester6239
      @markchidester6239 7 лет назад

      rhkips Maybe Paul needs to get there before lunch time, lol! Great video!

  • @ozzstars_cars
    @ozzstars_cars 7 лет назад +2

    With all the rain and melted snow water that door lock/window switches get it interesting they don't short out sooner than later. Manufacturers don't seem to make door switches water tight

  • @madyoza3061
    @madyoza3061 6 лет назад +1

    4 grounds would make sense if all the windows have the same auto feature.(I was confused for a second too when you said that). also what if everyone used the windows simultaneously, you would need 4 ground wires not to burn something out.

  • @misterhandy5121
    @misterhandy5121 5 лет назад +2

    freaking awesome !!!!! another one from a real teacher , not like these other fake mechanics on you RUclips that are just part changers without even knowing what the actual issue is!!!!! Paul For President!!!

  • @carlosvaldez3874
    @carlosvaldez3874 6 лет назад +1

    Hi, good video, i have installed 2 power windows to my manual windows. Passenger and rear behind passenger. Have not installed the driver side with master switch, my question is, does it need master switch on driver side installed in order for all the other windows to work?

  • @alpinewhite
    @alpinewhite 7 лет назад +2

    The way I would've done it would be to put a voltmeter across the green (+) and red (-) wire. In the "up" position, you should read +12volts. In the "down" position, you should read negative 12volts.

    • @jackshea6937
      @jackshea6937 2 года назад

      Yes! - Why not do it the easy way? Save watching a 44 minute video, (which is great), but speaking for myself, I'd prefer to just get on and fix it - life's too short.

    • @josepeixoto3384
      @josepeixoto3384 Год назад

      There is no neg. 12V ;
      there is ONLY +12V and 0V(ground) but i get what were saying

    • @alpinewhite
      @alpinewhite Год назад

      The voltage you read on the DMM is the voltage of the red wire relative to the black wire. If you switched the red and black wire, you will read a negative voltage.

  • @alpinewhite
    @alpinewhite 7 лет назад +1

    19:15. In an ideal world, there should be zero resistance between where you're tapping and the car's chassis. But there is small resistance between where you're tapping and the chassis. That resistance is fixed, albeit a very low resistance. Remember Ohm's Law, E=IR (voltage = current x resistance). By allowing more current to flow through that section of wire, the voltage drop across that wire just went up. That's why your voltage went up from .05 to .97 volts.

  • @Boro-Lineman
    @Boro-Lineman 5 лет назад

    Resistance in series voltge drop over each resistor the motor was dropping the majority of the battery voltage as lower resistance than the one in tne switch the 0.97 volts is the voltage drop in ths switch the ground on the other side of tbe switch resistor will be close to 0v

  • @wyattoneable
    @wyattoneable 7 лет назад +2

    The detail you include in your videos are well appreciated. It helps me understand more about circuit design.

  • @RAFICKDAMISONMOYO
    @RAFICKDAMISONMOYO 9 месяцев назад

    Scanner danner subscriber forever ❤❤❤

  • @donaldlee6699
    @donaldlee6699 Год назад

    My Buick Park Avenue 2002 front driver switch has quit. Power windows. Door locks. And mirror has quit working. I have purchased a ZKZYEE Vehicle Super Probe KM50 to test with. It has been difficult to find anything on the internet about the fuses. I believe the fuse is in the back under the seat? Or under the dash. The Windows quit previously, and the door locks on the driver side. Then, after about (2) two months the light on the switch began flashing. I tried it and it started working again. Now, it has stopped again. And the passenger side has stopped working also? It is difficult to find a specific video for the 2002 Buick Park Avenue. I like your video. I subscribed.

  • @zenSutherland
    @zenSutherland 3 года назад +1

    Seriously great work! I have the same problem, and saw what a snarl taking the switch assembly apart (i'm famous for taking things apart and watching springs fly out and jumping into cracks in the universe) so I'm ordering a new switch assembly. Your explanations are very helpful!

  • @selador11
    @selador11 5 лет назад

    I have this car. I have this problem. Just started watching the vid, hoping to get a solution. Just a remark, first. That auto feature... Is that "auto" light supposed to ALWAYS glow dimly? Mine does. Always. Key on, key off, key completely removed, everything turned off. The light glows dimly, no matter what.

  • @jamesward5721
    @jamesward5721 Год назад

    The switch is burnt, but it being bad is a red herring - note how much slower the motor was going up - it's intermittently bad itself & that's what fried the switch - the motor needs changing as well. Cleaning it in this case most likely won't work as it will be the sealed plastic gear wheels that are binding & you can't get at them. If you can make the switch work again, swap out that window motor too, or the fix won't last. :-( I was at the identical all morning today..
    BTW if people don't have a power probe ( I do) you can run the window motor with a cheapo 12v variable power-supply, just swap the +/- over to go between up & down, it will run the motor no problem, might get you out of a pinch if you have a bad switch & a window that is "stuck" down. In todays case for me, which is identical to that ^^, I will swap out the switch & the window motor for good used ones, because just fixing the switch will only work for a little while till it fries again. Change both. :-)

  • @nickayivor8432
    @nickayivor8432 2 года назад

    Good Evening ScannerDanner take care and have a great day ScannerDanner God bless you ScannerDanner 👍
    🌟🌟🌟🌟🌟 Great tutorial thank you 👍
    From Nick Ayivor from London England UK 🇬🇧

  • @hyeeagle
    @hyeeagle 7 лет назад

    Note: don't try to fix TOYOTA window master switches,because they have recall ( factory defect ) inside switch buttons get melt and stop working,sometime even worse they get fire and burn door panel and wiring ( I seen it )
    So when you find window master switch is the problem check with dealer for recall or TSB before you do anything or if you like to sale window switch that's different story. Also you can change window switch circuit board if inside window switch is not melted.
    Note some of Toyota master switches are or very been checked by dealers as I mentioned recall and installed one way screws which is no one loud to open except dealers.

  • @clusa3721
    @clusa3721 3 года назад

    Hahaha... What you need to do now, I would say... is to kick that power switch or throw it and try it again hahahhh who knows? it might work just for fear of being thrown in the hands of even more evil people... Thank you, you made me laugh lol !!

  • @pinpointautomotiverepair1592
    @pinpointautomotiverepair1592 7 лет назад +4

    Great video on this window circuit. I am also a huge fan of what you did with the diagram, using paint to display voltage measurements through different portions of the troubleshooting. Makes for a very clear and understandable procedure! Tons of great information here to be gained on this system, as well as lessons that can apply easily to others. Wonderful video as always!

  • @rku840
    @rku840 4 года назад

    I doubt the circuit diagram is complete, where is the thermal switch? I have my camry drive side powered window problem. When going down initially no problem, but when going up a short distance it stops, then I need to wait for few minutes before it can move a little bit up again. To fully close the window it has to stop a few times and each time a few minutes before I can reactivate.

  • @TerryThrower-ci8ek
    @TerryThrower-ci8ek 11 месяцев назад +1

    Thank you so much for your time explaining how this switch works, it really makes sense now.

  • @2094Ryan
    @2094Ryan 7 лет назад +1

    Great vid buddy, I am glad to see the power probe video, it's something I have in my box but never use as am scared of frying something lol but interested in learning how to use it properly. Please do a power probe video. And am glad you shared it outcome with us lol.

  • @baxrok2.
    @baxrok2. 7 лет назад +1

    Excellent presentation Paul. Good lessons in a couple of areas. Thanks! Oh, and thanks Pete for making this possible.

  • @blingmotions6996
    @blingmotions6996 2 года назад

    I was checking a control like that one but no doors work no light in the control, only the door lock button work nth else and i fine know broken fuse..plz help

  • @stigonutube
    @stigonutube 7 лет назад +1

    yeah i had this problem on a 1997 nissan last year i found circuit complicated to figure out, lucky i tracked it down to dirt in the switch contacts and after a clean was working again.

  • @BigDog50001
    @BigDog50001 7 лет назад

    Checking window master switches, especially ones with integrated modules, can be tricky with a Power Probe. Nice video Paul.

  • @toppledgod
    @toppledgod 7 лет назад +1

    I'm really surprised you don't carry contact cleaner, it's amazing at removing carbon deposits!

    • @ScannerDanner
      @ScannerDanner  7 лет назад

      I'll add it to my toolbox! This didn't look like something any cleaner would help with.

  • @Tech-28
    @Tech-28 Год назад

    Danner your working on one of the most reliable automobiles ever manufactured.

  • @jamesortega8681
    @jamesortega8681 Год назад

    tryin to fix mine too , and mine has 4 grounds as well for the power window master switch

  • @mohammednovalija
    @mohammednovalija 2 года назад

    I was wondering about the "GREEN" wire you measured.
    It looked like it was green with some sort coloured spots on it rather than solid gren.
    Looking at your schematic , there is at least 1 green wire with another colour combined with it as well as a solid green
    So my thought is you may have measured the wrong wire when testing.

  • @joachimjohan1215
    @joachimjohan1215 5 лет назад +1

    yeeeeeeeehhhaaaa....... i dont think so.....: "trying to do a real quick one here guys" HAhehh i love it!!

  • @Joeelectronicschematicsforauto
    @Joeelectronicschematicsforauto 4 года назад

    I never really liked the power probe I just like connecting a true cable from the battery positive or battery negative

  • @playuhhaytuh5633
    @playuhhaytuh5633 4 года назад +1

    Hey man, you make very helpful videos Keep it up 👍🏽

  • @faizanautos3764
    @faizanautos3764 6 лет назад

    What is this software or website, you use for wiring diagrams... plz tell me free website for free wiring diagrams...

    • @ScannerDanner
      @ScannerDanner  6 лет назад

      It is called shopkeypro and is a $150 a month program. There is a DIY version where you can purchase a 1 month pass for your car for $20 which gives you access to the same material I show.
      www.eautorepair.net/marketing/html/about_us.asp?VID=&Count=Y

  • @throttlebottle5906
    @throttlebottle5906 7 лет назад +1

    "trying to do a real quick one here guys" noticed it's 44 minutes of video about the same time I heard it, and that caused a good chuckle :))

    • @ScannerDanner
      @ScannerDanner  7 лет назад

      Lol it would have been if I wasn't such a dumbass in my original explanation of what was going on with the switch and my power probe readings.

  • @1weirddoe571
    @1weirddoe571 5 лет назад

    SD, my (FORD 2000 Windstar) motor ohms infinity or randomly 1-2M Ohms. Isn't there a fusible link inside that's supposed to protect the motor? What about the windings in the motor? How do you know one of the loops of the windings is not open even though the rest of the motor is okay? How do you know if one of the loops isn't open and the motor still works so-so that you can't tell the difference?
    Show less

    • @ScannerDanner
      @ScannerDanner  5 лет назад

      I need a time frame of a specific test I was doing to answer your question, it is too broad otherwise. Thanks!

    • @1weirddoe571
      @1weirddoe571 5 лет назад

      @@ScannerDanner, I Ohmed the motor wires and got "infinity" or 1-2MOhms. Then reconnected since had +/-12V switched and kept banging closed the door while depressing up/down and it started working again. (Even, before, connected straight battery to motor and still couldn't jump it up or down.) Now I don't have to rip door apart. Much Thanks.

  • @mikeanderson1994
    @mikeanderson1994 7 лет назад +1

    man ur amazing i watch all ur videos and ur the best i liked scotty kilmer and eric the car guy i mean u 3 are the best in youtube keep up the good work best regards to all

  • @jeanvaljean126
    @jeanvaljean126 2 года назад

    Scanner Danner, the guy who work everytime on cars with flat battery....

  • @fredflintstone8048
    @fredflintstone8048 7 лет назад

    I agree that the diagram does not appear to reflect the circuit which holds the power on the window motor to travel all the way down, or all the way up automatically. My guess is that it will be some kind of transistors or FETs in parallel with the manual switchs. It is also my guess that the resistor in the diagram that is more than likely clamped by the diode (notice it's in the circuit with reverse polarity) is the circuit that tells the solid state control when the window has reached the end of the travel. The amount of current through that resistor will increase sharply when the motor reaches the end of the travel creating a voltage drop seen by the controller to turn off the window motors. Typically a diode is used as a clamp to prevent the voltage drop from being too great due to high current draw thus damaging the input that monitors the voltage drop. Regarding the circuit board being damaged, what I believe we're seeing is not burned connections, but instead soldering flux that was not cleaned off. It could indicate an attempted repair in the past, or a rework at the factory due to defect.

    • @ScannerDanner
      @ScannerDanner  7 лет назад +1

      Great insight! Thank you.
      I only mentioned the "burnt" contacts for the untrained eye. That would be the first thing they would see and I wanted to make a point that, that was not what you're looking for.
      You would be correct, "burnt" was not the right word to use.

    • @fredflintstone8048
      @fredflintstone8048 7 лет назад

      Oh, and I forgot to mention, great video! I really enjoy the discussions about the voltages found on grounds, loaded and unloaded, and how those things can help us determine a problem. As you point out, the amount of current flowing through a circuit will determine the voltage drop so the more current the higher the voltage will be above ground, or battery negative. The same holds true on the positive side, or really anywhere in the circuit. The perfect wire, or circuit would have zero resistance, but that's never the case. Wires, switches, connectors all provide a little resistance in the circuit and will thus provide a voltage drop proportionate the the amount of resistance, and the amount of current. Ohms law.
      It's a thinking mans game, and rewarding as well when we understand how it works. We need the money of course, but it's satisfying to work on these things when we come to understand what's going on. Again, thanks for sharing another great video.

  • @8953147
    @8953147 7 лет назад +1

    Great explanation, with wire diagram, of reverse polarity switches and switch dissection! DeOx-it works great for cleaning and lubing electrical contacts.

  • @swlmmrtn
    @swlmmrtn 7 лет назад

    I have seen these problems so many times in my time working on cars. Everyone should really look into taking the switch apart and getting to know the contacts inside "rocker" switch. They get built up with so much dust and gunk that they simply don't make contact. The down contacts are completely different than the up contacts inside the physical switch itself. I'll bet I've cleaned upwards of 50-60 switches for people over the years and got their windows back to perfect working order with simply contact cleaner, small brush, (sometimes toothbrushes work best), and some dielectric grease. Give it a shot on a known bad switch if a junk pile, you'll be amazed how well it works and how little effort it really takes. Saves money and customers LOVE when you can fix the little things instead of replacing.

  • @toothless_2v594
    @toothless_2v594 3 года назад

    I looked at my window switch and my circuit board is broken in half lol. Guess my diag is done 🤣

  • @Ottonic6
    @Ottonic6 4 года назад

    I am currently diagnosing a 1992 4 Runner drivers window that won't go up, but anyway, looking at the FSM Electrical "System Outline" which explains the operation of the different controls in the master switch it explains that in auto down 12v is sent to the motor while at the same time is also sent to a solenoid (inside the little "Solid State" box on the Mitchell diag. that doesn't show anything) which locks the switch in the down position and when the motor hits its down limit increases the current through the solenoid which disengages it along with the switch... There's a lot more going on with 8 resistors,4 diodes (1 zener), a couple caps etc... I know that won't play a part in my diagnosis, but what you explained really helped me out in direction when I attempt to fix my problem. Thank you for your time and expertise.

  • @josepeixoto3384
    @josepeixoto3384 6 лет назад

    8.99 volts?! there is no guarantee that the module works at 9 volts! it's a 12 V system;
    I do not test for grounds or for power with a voltmeter; car windows do not work with voltage; they work with current (Amps);
    best to use a made up test light, with,at least, a 21 or 25 watt bulb and two wires,unless your probe has that load capacity

  • @rwbishop
    @rwbishop 7 лет назад +1

    Maybe it's just me, but I cringe at the thought of Power Probes... in my experience they generate more grief and/or confusion than any other shop 'instrument'. Especially in the hands of less experienced techs. I've been given a few through the years; I smile politely, say thank you, then hastily make the things 'disappear' at first opportunity... just my .02¢ worth. Having said that; yes, if higher amperage circuits are completed/broken via the probe tip (with the switch first held in the *appropriate/correct* position), switch life can be substantially extended. Also, all Power Probe stuff (that I'm familiar with anyway) is compatible with garden variety 4mm banana leads, test probes and all that.

    • @D_J_R_S
      @D_J_R_S 7 лет назад +3

      rwbishop
      PowerProbe is confusing AF! All I use my for is a controlled way to drag power around the vehicle.

    • @ScannerDanner
      @ScannerDanner  7 лет назад +1

      I definitely had some issues with it on this one. So much so, I almost scrapped this entire video.

    • @djr3485
      @djr3485 7 лет назад +2

      The Power Probe like any tool, is simply another device which can be extremely useful in diagnosing electrical problems. Paul's use of the PP was entirely appropriate in this instance because it enabled him to eliminate the entire circuit and load leaving only the switch. The problem I see with the PP is when people expect it to do the troubleshooting for them. If a tech does not understand what readings should be nor what the tool is actually doing, then flashing lights and buzzers can be quite misleading. The best part of the video was when Paul opened up the schematic and began to work through the problem. Electrical repairs have very little in common with mechanical ones, and the time taken in understanding how the circuit works is usually the most valuable investment a tech can make.

  • @JustLikeGreta
    @JustLikeGreta 4 года назад

    How can there be only 68 downvotes for this video. One of the worst I've ever seen.

    • @ScannerDanner
      @ScannerDanner  4 года назад

      for those who are not just seeking silver bullets, this is gold. you found the wrong channel, unless you want to actually learn something instead of just fixing your problem

  • @Asian_Connection
    @Asian_Connection 4 года назад

    HELP!!!! Your videos are great. I love my 1997 4runner Ltd with 240k also. I want keep it runner forever. Can you help me with one issue that I can't solve. My passenger door window only goes down but not up. I have replaced the window motor already but it is still having the same issue. I tried both driver and passenger side buttons, checked the fuse but they both can't bring the window up. Can you give me a few pointers in troubleshooting the issue. Thanks.

    • @ScannerDanner
      @ScannerDanner  4 года назад

      broken wire in the door jam most likely

  • @jackshea6937
    @jackshea6937 2 года назад

    You've motivated me to buy a new $29 switch module and hope for the best: trouble-shooting is god's work - clearly.

  • @leedress2187
    @leedress2187 7 лет назад

    brake clean would've cleaned up those contacts.. Just kidding. I always have a can of quick dry contact cleaner around for stuff like this. i think you had further damage away from the contacts though.. . love your thought process though. Keep up the good work!

  • @little739
    @little739 5 лет назад

    Hello, Paul If you didn't get battery voltage in the down position of the red wire, would you still apply 12v to the green wire in the UP position?
    With perseverance and your guidance, I now understand the diagram and have answered my own question. Thanks for the video.

  • @DougHinVA
    @DougHinVA 6 лет назад

    it's too complicated and too much digressing for a normal guy to understand

    • @ScannerDanner
      @ScannerDanner  6 лет назад

      keep watching and following me and you will not feel this way very soon

  • @gvvq-pi5ml
    @gvvq-pi5ml 7 лет назад

    Hi Paul i think the reason when the switch is in the middle it puts and earth on both sides of the motor, it's kind of like a dynamic brake if you will, they used to do it on wiper motors in the UK in the 1970's to stop the momentum of the motor carrying it over the park switch and carry on working when turned off, when the park switch opened it put an earth across the motor stopping it dead...hope that makes sense...with windows i used to put a bulb in place of the motor as they dont worry about polarity if you put a volt meter in place of it of course it would try to go backward on one side and forward on the other...from Fred in England.

  • @verajavi12
    @verajavi12 6 лет назад

    polarity led lights have also threw me off on both low volts= no red led light and no green light when expected because of voltage thresholds in power probe internal circuitry.it was really bad on power probe 1,later power probes had a digital voltage reading that enable u to trust the voltage reading more than the red or green LEDs.often times old school test lights are just better because of simplicity.

  • @ldiazmdiaz
    @ldiazmdiaz 5 лет назад

    To give some life to that switch, I would use a small file lightly (from harbor freight) and contact cleaner and then you would feel like a certified dentist.

  • @edwardjames6070
    @edwardjames6070 7 лет назад

    those switch assemblies are very similar all throughout toyota. I have a 96 land cruiser and an issue arose with the windows. I know that being a 'parts swapper' is not preferred by you, but $10 and an hour and a half of time and I was able to replace the assembly and have it working by using a switch from a 96 four-runner.
    after investigating the faulty switch I found corrosion at the faulty contact. now I have a spare switch assembly, and more important, I was able to keep the wife happy.

  • @Jpilgrim30
    @Jpilgrim30 7 лет назад

    Early 2000 GM trucks are bad about solder joints cracking in the abs control module. I pull those all of the time and resolder them. Easy money all labor.

  • @theadventuresofjavier8698
    @theadventuresofjavier8698 7 лет назад +1

    hey Paul ,I know everyone gives you props all the time but I wanted to say I really do appreciate the time you invest in me personally.yes me.love all your videos.when I felt my professional auto tech career was stalling and becoming stagnant I found your videos.they started a fire inside and makes me want to get deeper into auto repair more than just being an r and r guy.God bless you always my brother in Christ.sorry for bein long winded.

    • @ScannerDanner
      @ScannerDanner  7 лет назад

      But I still need to hear this. It keeps me motivated. Thank you so much my brother.

    • @D_J_R_S
      @D_J_R_S 7 лет назад +1

      ScannerDanner
      exactly the same story for me. You and Schrödinger's Wrench(that's the channels name, right?) completely flipped my mentality towards the profession that I had grown tired of. I'm forever thankful, because that fire has crept over to other parts of learning in my life. To you, I bow down.

    • @ScannerDannerPremium
      @ScannerDannerPremium 7 лет назад

      Thank you my friend

    • @aussiefirestorm
      @aussiefirestorm 7 лет назад

      Second and/or third the above comments. You have made me want to be a better mechanic, it is better to be good rather than lucky.

  • @kennethnichols7263
    @kennethnichols7263 7 лет назад

    Great video. I don't have a schematic but what I would expect for the auto down is a self latching circuit. In the old days a relay was used and the switch side of the relay would be put in parallel with the switch. The coil for the relay would be put on the unpowered side of the switch to ground. Once the switch is closed the relay closes its switch side maintaining the voltage on the other side of the switch to keep the relay closed. The latch is now in effect. Now with the window motor this voltage should be enough until the motor hits it end of travel and the motor stalls. When the motor is moving a back emf (electro-motive force) is generated which is proportional to the speed of the motor. This is because all D.C. Motors are also generators. At the end of travel the voltage will disappear and the coil will loose its power and the relay will open delatching the circuit. Now these days the relay may have some kind of transistor circuit to replace the relay. By the way, multiple grounds and power pins may be put on a circuit board due to the limited current carrying capacity of the connector pins. The traces on the board or power/ground planes can be beefed up to carry high currents but there is a spec on the pins which is the limiting factor.

  • @lovetolearn5253
    @lovetolearn5253 7 лет назад

    pp4 has a continuity test to check the Integrity of the switch great videos but like offer viewer stated the pp4 does have a lot of capabilities I don't even understand half but learning it's fun to learn

  • @eddiemartinez265
    @eddiemartinez265 7 лет назад

    None look bad but the burned one's that is not burned it is the flux that look like that.

  • @USA4thewin
    @USA4thewin 5 лет назад

    na man awesome I used baby wipes and cue tips my windows is working great again thank you so much for the video.. Note there is a nasty spring for the window lock the square one took me a while to figure that one out and install it properly

  • @throttlebottle5906
    @throttlebottle5906 7 лет назад

    I'd guess the resistor is there for the "auto" feature to sense motor current, which seems redundant since the grounds go to the "magical solid state circuit" or the diagram is plain wrong/missing other things

  • @cwj9202
    @cwj9202 7 лет назад

    I would assume the solid state device serves as an electronic latching device during the auto down function, and so that part would not be displayed in the electrical schematic. I prefer to utilize my DVOM, not the test light, to check the loaded voltage readings and see the loaded ground circuit voltage rise. Good video as always. Keep up the great work.

  • @uptownimports-foreignautor5338
    @uptownimports-foreignautor5338 7 лет назад

    You were talking about the wiring diagram possibly being wrong, the "Valley Forge SVG" diagrams like the one you are showing in the video are OK for something down and dirty / easy to read. To get better more accurate, detailed information about the circuit and the connectors OE diagrams like the ones in Alldata, DirectHit, MotoLogic or OE websites are waay better. I've been sucked into the Black Hole of electrical diag using the Valley Forge diagrams. The OE diagrams are not all the same like Valley Forge so there is a bit of a learning curve to them but once you figure them out they are great.
    I have these two sets of contact files by these guys, they work real well. The flat ones will clean both sides of a flat male connector at once! Check it out.
    Flat files: www.ipatools.com/products/index.php/diamond-tip-electrical-terminal-cleaners.html
    Round files: www.ipatools.com/products/index.php/ipa-8042.html
    Thanks for the tip on the reading of the Power Probe!!

  • @pierretessier1682
    @pierretessier1682 4 года назад

    you're very very patient.The most important is that you knew what was the problem.Very very good troubleshooting my friend!

  • @jaakkomarin1789
    @jaakkomarin1789 7 лет назад

    Could the resistor inside the switch be a shunt resistor for the autodown solid state circuit to be able to measure current flow of the switch via voltage drop across the resistor?

  • @robertofkennedy
    @robertofkennedy 7 лет назад

    your probe has power feed test and ground driver test it calculates resistance in the circuit and gives you a reading in ohms

  • @tnamen1307
    @tnamen1307 5 лет назад

    Sir, could you be specific on Hyundai i20 power motor which has 6 wires?????

    • @ScannerDanner
      @ScannerDanner  5 лет назад

      Here is a link to get wiring diagrams for your car. eautorepair.adtrk.biz/?a=10817&c=24&p=r&s1=
      You can get access to the same wiring diagrams I use for an individual car for a month for less than $20

  • @MrTwisted1977
    @MrTwisted1977 7 лет назад

    the auto down function is simply a latching relay or a basic transistor curcuit if u think this is difficult try working on cars with can bus systems.these old Toyota circuits are just child's play to the right person so basic and bog standard it's boring at times diagnosing them.anyway scannerdanner is a champ for going through it in such depth especially the new techs.

    • @ScannerDannerPremium
      @ScannerDannerPremium 7 лет назад +1

      Thank you but i disagree that CAN bus systems are more complicated. It's just different, same principles apply to testing an output of a power window module on a network.

    • @picoboo5048
      @picoboo5048 7 лет назад

      ScannerDanner Premium Do you have any videos about diagnosing comm issues?

    • @ScannerDanner
      @ScannerDanner  7 лет назад +1

      I have many no com videos from shorted sensors and blown fuses and more recently with the network itself.
      I have two coming up. Next week on this channel, I will be uploading a no com with the TCM on a 2012 VW Jetta that I filmed with Tommy Wolfe of Positive Lead Diagnostics.

    • @picoboo5048
      @picoboo5048 7 лет назад

      ScannerDanner ok cool, I've diagnosed network issues before but it would be cool to see how you go about it. Especially with Can systems with Lin buses and all the other protocols I don't remember 😄

  • @madmotorrepair1748
    @madmotorrepair1748 7 лет назад

    Thanks Paul, much appreciated dedication here, showing how to use a power probe and the directions it can take you, I will keep this in mind!

  • @jugubantan7740
    @jugubantan7740 4 года назад

    Where do I go to get some wiring diagram!

  • @michaelmcdowell8801
    @michaelmcdowell8801 7 лет назад

    that was a lesson in confusing a apprentice. should have looked at that video several times before posting

  • @joopterwijn
    @joopterwijn 7 лет назад

    Without a current the potential over a resistance is zero, you will measure ground if the resister is not there.

  • @tnamen1307
    @tnamen1307 5 лет назад

    Sir my car i20 windows motor connector has 6 wires on it. How to get the wires for roll up and down windows?

  • @arcburn3364
    @arcburn3364 5 лет назад

    I never carried a spit cup for my chewing tobacco in my welding trucks, so I gave my drivers side window switch a workout.

  • @TomTremayne
    @TomTremayne 5 лет назад

    Dude, can you come over to London and fix my windows!!! I've got power to the switch, passenger side, took the switch apart and it's mechanically sound, changed the motor as well but still my passenger side window goes down but not up and doesn't respond at all from the master driver's side switch. Maybe it's the contacts, dirty where the naked eye can't see, maybe the Italian wiring has failed, maybe it's something else entirely, who knows!

    • @ScannerDanner
      @ScannerDanner  5 лет назад

      We can help you on my forum. IT is free to join
      www.scannerdanner.com/forum.html
      Hope to see you there! We definitely need to look at a wiring diagram

  • @konquerorx
    @konquerorx 6 лет назад

    Mr Paul! Just a question sir. I have a Toyota Camry 1996 equivalent called a Toyota Windom. I'm not sure if it's in the states.
    Basically it has these frameless windows. Similar to the Subaru's. So when you close it, the window suppose to drop slightly, to shut the door, or open it. I've tried to initialize the windows but that did not work. So I'm unsure how to approach this one.
    Thanks in advance sir

    • @ScannerDanner
      @ScannerDanner  6 лет назад

      I do not know my friend. Post it to my forum. I have thousands of members from all over the world. Someone may be able to help you. Thanks!
      www.scannerdanner.com/forum/post-your-repair-questions-here.html

  • @marcoromero2345
    @marcoromero2345 4 года назад

    Se entiende la explicación que manual está usando

  • @all-about-programming
    @all-about-programming 3 года назад

    You always the best... ...Can you tell me where I can get the best wiring diagram please

  • @patrickliverpool6487
    @patrickliverpool6487 Год назад

    Great job Paul you are amazed

  • @AGuysGarage
    @AGuysGarage 7 лет назад

    Good Video Mr. Danner, thanks for posting. I like when u post your misunderstandings or stuff you say that isn't entirely accurate, shows the Human side of Utubers, and you are one of the better ones sir. Much Respect and Many Thanks to You. Hats off.

  • @ironmike742
    @ironmike742 3 года назад

    The extra grounds are to help carry the amperage and keep resistance and heat down

  • @greygoosemafia
    @greygoosemafia 7 лет назад

    in my 99 ram i did that method. switch it back n fourth and it works now.

  • @JohnDoe-uq3mx
    @JohnDoe-uq3mx 7 лет назад +1

    Window motor problems were always a PITA for me.

    • @aleishasantos8914
      @aleishasantos8914 5 лет назад

      But you dont fix d switch in d end n dat really matter.

  • @mrghiax
    @mrghiax 7 лет назад

    Nice video Paul. As you openly admit - very nearly ended up in the reject bin but personally speaking I'm pleased it didn't. I very much doubt you are the first to be caught out using a new tool. Full credit for owning up to your rare mistakes and learning from them.

    • @ScannerDanner
      @ScannerDanner  7 лет назад

      Thanks friend. I appreciate you guys so much

  • @1weirddoe571
    @1weirddoe571 6 лет назад

    I smashed the two LEDs on my passenger side switch that illuminates can I solder in some Christmas light LEDs will that be good enough?

  • @tboneproductions2453
    @tboneproductions2453 5 лет назад

    Damn, no happy ending! Sorry, couldn’t help myself😊