Watching your video made me learn more. I replaced the si100 12x25 fan with a noctua 12x15 with a maximum speed of 1850, and the case shell does not need to be damaged.
Not sure how I got here, but this is good. Ordering one for later when the pump goes out. I think with a slim fan it would have fit perfectly, thats what I'll do. I sure do love the revised H1 case.
For those with NZXT H1 v1 case: I was able to install the SL-100, following the steps from the video. It was kinda hard to install it properly, and the fan does not fit it perfectly, but the temps are kinda good. Temps: (28/29°C Avg on my room - Summer Season) - AMD Ryzen 5 3600 (Overclocked at 4GHz on a Hackintosh) - CPU temps: on idle 45 / 46°C - Max temps on benchmark (Geekbench): 54°C / 56°C - Tip: Undervolting CPU could decrease a few °C. Kinda good, not sure if this is much better than the NZXT pre installed AIO, but as a replacement seems just right. Also as I said before, this temps are on Summer Time, with 40°C outside and 29/30°C inside the room. I expect 32 / 35°C CPU temps on idle on Winter Season. Thanks to @DalraeMyo for the video!
Hey, I got this cooler as well and tried to install it on my AM4 board, but the cooler is kind of too wide on the left side of the case, it is pushing against the support pillar of the case, even without a fan attached. I'm no expert in PC building (hence I got the H1) but am I doing something wrong? In the video, he's using an Intel board and that mount allows him to rotate the cooler 90 degrees, so the long end is on the bottom rather than on the left side. But you seemed to manage to install it on an AM4 board. I'm using an MSI B550i Gaming Edge Wifi motherboard if that changes anything. E: I think after comparing some B550i motherboards just visually, my MSI board just has the CPU mount very far on the left side. Guess that's bad luck then, have to return it and get the V2.
@@drchtct Happened exactly the same to me mate. The Cooler is pushing against the support. Try to figure how it works and fits better (for me worked like in the video), and install it without the fan first. The fan will not fit perfectly either, and the claps or the grabbers from the fan will not install properly. In my case I had to tie them with some black "zip ties" or whatever them are called. In the end, I was able to install it, and modify the V1 case to close it properly (like in the video). I was struggling for a bit, but with patience and following the video I was able to fit it and install it. Also the temps are pretty good, as I said in some other comment, or on the top one. Notice me how it goes mate. And do not surrender, it should work with patience.
@@DEV_XO Thanks for your replay mate. What motherboard do you use? I think my CPU is just placed too much on the left side. I compared the photos from other boards and they seem to have it more central. I don't know, I really tried to squeeze it, but don't want to damage anything because I can't return it afterwards if it's scratched and stuff. If it doesn't work it's not the end of the world, NZXT refunded me the money for my entire H1 because they couldn't deliver a new AIO during the warranty time.
@FlashTVBox My motherboard is a B550I AORUS PRO AX As I said before, in my case does not fit it perfectly either (besides the Cooler is installed correctly and mounted as It should be) it's more or less on a left side, and looked like I could break something, but following the video, and figuring out how to setup it properly, it ended up working. I know the feeling about that it will not fit or you could damage the cooler / anything else, as I said, it's kinda hard to make it work and you need to try to fit the Cooler in a few ways (for me worked like in the video, same position / orientation ) I don't wanna you to push it to the limits and make it work, in my case had no chance. Was to make it work, or to go for a new case, or a Noctua lower profile CPU Cooler. (With lower performance for sure) If you can get a new case, or to make a refound, feel free to go for it. Because no matter if you install the cooler, the H1 case still need to be modified (like in the video). So yeah, notice me how it goes and what you will end up doing. I'm "developerxo" on discord, in case you wanna add me, maybe I could send you some images from my build.
@@DEV_XO I just tried to fit it again and the cooler itself now fits in but it's still below the support pillar. So I tried putting the fan on top and it would be offset by a few cms to the right, so I need zip ties and have no idea how to mount the fan without reaching the left side of the cooler. I think I'll just go for the Noctua LN-L12S as it includes 90 degree kits for mounting it in other directions. It is about 5 degrees hotter than this one, but I don't really mind considering I'll stick to Ryzen 5 in this case anyway, and the temps you showed +5 degrees is still more than enough for me. Just want it to finally work again..
This is slick, I was planning to get this case but the aio pump failure was a deal breaker, should have thought about this , the v2 is bigger aswell vs the older model. the temps with i7 at 170watt looks reasonable, it would have totally handled the i5 13500 i have.
PRO TIP: If your motherboard is GIGABYTE or AORUS AM4 - this may not work for you as the AM4 cpu socket is offset to the far left side of the case. A solution would be to buy a thermalright AM4 bracket for Peerless Assassin Series so you can flip the heatsink perpendicular to the IO ports. Saves you $$$$ from buying a new cooler or another mobo
@@thenewdesign have to be 2 slot with 58mm max of thickness. I think all of the PNY 4070 TI came with 3 slot. You can set the fan curve of Gigabyte Eagle RTX 4070 TI, make it more quiet than it's default.
@@dhajal Thanks! I ended up going w/ the MSI Ventus 4070 Ti OC which is apparently significantly smaller than even the Eagle, does really well w/ undervolting, and seems perfect for this case
Hi ,Great build : and i ask you : 1) i ve seen you can add 4080 FE only removing sdd case and “ cut” or replace 3 slot bracket and remove filter on H1.( 4070ti not great GPU for 4K ) 2) i think you can change AIO with cooler master one for silent and temperature performance? Or add 280mm Aio with front/back cover custom ( easy to find on Etsy). What about ?
Haven't seen any like this before, really nice build. I'm quite interested and also want to re-make my own, btw what is the clearance for the cooler if you don't mind?
There is room for SFX-L standard power supply installation. (I think it's because the previous version was SFX-L standard power supply.) However, if you use a lot of modular cables, you may not have enough space.
To use the SI-100 as it was, the radiator mount bracket had to be removed due to a height issue. If you use a 140mm slim pan, you don't have to remove the radiator mount bracket. However, CPU cooling performance can be significantly degraded.
There was no problem with the operation, but the cooling fan noise bothered me, so I replaced the power supply. You can easily replace the power supply by removing the four screws on the power plug side of the power supply.
@@danielvipin7163 Idk, you basically have to cut some claps in the case to fit it (like in the video), so I guess no space at all? I'm using the fan that comes with the Cooler, but If you have in mind to use a smaller fan, I'm sure it will be some available space, and the case would not need to be touched. In any case, the temps are good, and following the video it's all you need (and some patience while fiting everything in that tight space)
@@danielvipin7163 The heat sink size of the SI-100 I used is as follows. (L)120 x (W)108 x (H)74.8mm * For horizontal and vertical sizes, there may be a size difference that can be mounted depending on the location of the CPU socket position.
Asrock z690M ITX may not perform well at 13600K because it can output up to 150W. To mount the 4070ti TUF to the NZXT H1 v2, the dust filter on the panel must be removed and the latch securing the dust filter must be bent.
저도 비슷하게 제작을 하고 싶은데 cpu쿨러를 녹투아로 달게 되면 L12S 이런 거 달면 되는 걸까요? 아니면 조금 더 큰 쿨러를 달아도 상관 없을까요? 예산 상관없이 조용한 게 최우선이라서 저소음 공랭 찾다가 여기까지 왔네요 ㅎㅎ 아 CPU는 발열 적은 라이젠 7900 (Non X) 로 가려고 합니다
@@Shoong03 NZXT H1의 경우 조립난이도는 ITX시스템중에선 굉장히 낮다고 생각합니다만 난이도는 개인차라고 생각합니다. H1 난이도가 낮다고 느끼는 이유는 다음과 같습니다. 1. 기본 장착된 부속품들이 이미 반조립 상태에 기본적인 선정리가 되어있는 상태 2. 보드쪽 결합만 끝나고 그냥 선만꽂고 AIO 쿨러 결착 + 그래픽카드 장착만해주면 끝입니다.
@@DalraeMyo 그 선정리를 sf750으로 이미 충분하다 못해 좋은 시소닉 골드 750에서 플래티넘으로 한등급 올리시려고 25만원을 쓰시고 전부 재조립.. 존경합니다 물론 파워 소음 등의 원인도 있으셨갰죠 혹시 글카가 같으셔서 진짜 마지막 질문 드려봅니다. 4070ti벤투스에 신규 케이블이 적용 되고 화재 문제 때문에 결착을 잘해야하는것도 있지만, 3.5cm 거리 두고 꺽으라는데 간섭 문제는 없겠죠..? 너무 질문 드려서 죄송합니다 .. Itx 첨 입덕한 쌉초보라 고수님의 조언이 필요해서 이때까지의 답변 너무 정말 많이 도움되었습니다 너무 정말 감사합니다 은인이십니다
@@Shoong03 저는 PC관련 이야기하는거 좋아해서 궁금하신건 얼마든지 질문하셔도 상관없습니다. 신규 커넥터 녹는건 제가 경험 해보지못해서 어떻게 답변드려야 될지모르겠습니다. 제가사용하는 커넥터는 커세어 파워 전용 케이블이라 (굉장히 뻣뻣합니다.) 그냥 구부린 대로 모양이 유지되길래 그대로 장착했습니다. 너무 심하게 한쪽으로만 힘이가해질정도만 아니면 될거같습니다.
@@Restless2010 Thanks! I read Gigabyte makes an "Eagle" edition of the 4070TI that's physically smaller and requires no case modification. I might go w/ that since I'm putting a 13900KF in this anyway
MSI 바이오스 -> OC탭 -> 어드밴스드 CPU 컨피그레이션 -> 숏/롱 듀레이션 파워 리밋에 150W 적으시고 그아래 CPU 라이트 로드는 Mode3를 선택했습니다. CPU 라이트 로드의 경우 CPU 수율에따라 Mode 값이 달라지니 Mode 9 부터 순차적으로 내려보시는걸 추천합니다. (내릴수록 전압을 많이 깎습니다.)
CPU 냉각성능은 LP공랭 쿨러보단 일체형 수랭쿨러가 더 좋습니다. (140mm 일체형 수랭쿨러의 경우 대략적으로 듀얼타워 대장급 공랭 쿨러 성능은 나옵니다.) 다만 절대적인 냉각 성능 외에 쿨러가 구동하는 소음에 저는 불편함을 느꼈고, 수랭 쿨러보단 공랭 쿨러를 선호하는 것도 있었기에 과감히 수랭 쿨러를 탈거하고 공랭 쿨러로 변경하였습니다. CPU 언더볼팅의 경우 CPU마다 수율이 다르기 때문에 직접 안정적인 값을 찾으셔야 합니다. 언더볼팅하는 방법은 여러 가지가 있지만, 저는 귀찮아서 보드 제조사에서 제공하는 프리셋 값이나 CPU 전압 오프셋 설정을 주로 사용합니다.
04:29 PL1+PL2 Limite 170W
This i 100% "Sleeper build" and one of the best video how to to this. "chapeau bas"
Watching your video made me learn more. I replaced the si100 12x25 fan with a noctua 12x15 with a maximum speed of 1850, and the case shell does not need to be damaged.
How did you manage to fit the SI-100 without damaging the case?
@@thegeekystuff3800 use 12X15 fan
@@dhz666 Thanks, how much distance is left from the dust filters, and what's the fan noise like, if there is any?
@@thegeekystuff3800 8MM，It is less noisy than the built-in water pump, and the bios can adjust the fan curve
@@dhz666 that sounds promising. thank you, I'll consider your suggestion. I just ordered a silverstone air slimmer 120 as heatsink fan
Not sure how I got here, but this is good. Ordering one for later when the pump goes out. I think with a slim fan it would have fit perfectly, thats what I'll do.
I sure do love the revised H1 case.
For those with NZXT H1 v1 case: I was able to install the SL-100, following the steps from the video. It was kinda hard to install it properly, and the fan does not fit it perfectly, but the temps are kinda good.
Temps: (28/29°C Avg on my room - Summer Season) - AMD Ryzen 5 3600 (Overclocked at 4GHz on a Hackintosh)
- CPU temps: on idle 45 / 46°C
- Max temps on benchmark (Geekbench): 54°C / 56°C
- Tip: Undervolting CPU could decrease a few °C.
Kinda good, not sure if this is much better than the NZXT pre installed AIO, but as a replacement seems just right. Also as I said before, this temps are on Summer Time, with 40°C outside and 29/30°C inside the room. I expect 32 / 35°C CPU temps on idle on Winter Season.
Thanks to @DalraeMyo for the video!
Hey, I got this cooler as well and tried to install it on my AM4 board, but the cooler is kind of too wide on the left side of the case, it is pushing against the support pillar of the case, even without a fan attached. I'm no expert in PC building (hence I got the H1) but am I doing something wrong? In the video, he's using an Intel board and that mount allows him to rotate the cooler 90 degrees, so the long end is on the bottom rather than on the left side. But you seemed to manage to install it on an AM4 board. I'm using an MSI B550i Gaming Edge Wifi motherboard if that changes anything.
E: I think after comparing some B550i motherboards just visually, my MSI board just has the CPU mount very far on the left side. Guess that's bad luck then, have to return it and get the V2.
@@drchtct Happened exactly the same to me mate. The Cooler is pushing against the support. Try to figure how it works and fits better (for me worked like in the video), and install it without the fan first.
The fan will not fit perfectly either, and the claps or the grabbers from the fan will not install properly. In my case I had to tie them with some black "zip ties" or whatever them are called.
In the end, I was able to install it, and modify the V1 case to close it properly (like in the video).
I was struggling for a bit, but with patience and following the video I was able to fit it and install it.
Also the temps are pretty good, as I said in some other comment, or on the top one.
Notice me how it goes mate. And do not surrender, it should work with patience.
@@DEV_XO Thanks for your replay mate. What motherboard do you use? I think my CPU is just placed too much on the left side. I compared the photos from other boards and they seem to have it more central.
I don't know, I really tried to squeeze it, but don't want to damage anything because I can't return it afterwards if it's scratched and stuff.
If it doesn't work it's not the end of the world, NZXT refunded me the money for my entire H1 because they couldn't deliver a new AIO during the warranty time.
@FlashTVBox My motherboard is a B550I AORUS PRO AX
As I said before, in my case does not fit it perfectly either (besides the Cooler is installed correctly and mounted as It should be) it's more or less on a left side, and looked like I could break something, but following the video, and figuring out how to setup it properly, it ended up working.
I know the feeling about that it will not fit or you could damage the cooler / anything else, as I said, it's kinda hard to make it work and you need to try to fit the Cooler in a few ways (for me worked like in the video, same position / orientation )
I don't wanna you to push it to the limits and make it work, in my case had no chance. Was to make it work, or to go for a new case, or a Noctua lower profile CPU Cooler. (With lower performance for sure)
If you can get a new case, or to make a refound, feel free to go for it.
Because no matter if you install the cooler, the H1 case still need to be modified (like in the video).
So yeah, notice me how it goes and what you will end up doing. I'm "developerxo" on discord, in case you wanna add me, maybe I could send you some images from my build.
@@DEV_XO I just tried to fit it again and the cooler itself now fits in but it's still below the support pillar. So I tried putting the fan on top and it would be offset by a few cms to the right, so I need zip ties and have no idea how to mount the fan without reaching the left side of the cooler.
I think I'll just go for the Noctua LN-L12S as it includes 90 degree kits for mounting it in other directions. It is about 5 degrees hotter than this one, but I don't really mind considering I'll stick to Ryzen 5 in this case anyway, and the temps you showed +5 degrees is still more than enough for me. Just want it to finally work again..
케이스 기본 수랭 죽으면 답없을줄 알앗는데
새로운 해답을 하나 배워갑니다
감사합니다
This is slick, I was planning to get this case but the aio pump failure was a deal breaker, should have thought about this , the v2 is bigger aswell vs the older model. the temps with i7 at 170watt looks reasonable, it would have totally handled the i5 13500 i have.
H1 V2 풀매쉬가 되었네요 ㅎ 영상 잘 보고가욤~
PRO TIP:
If your motherboard is GIGABYTE or AORUS AM4 - this may not work for you as the AM4 cpu socket is offset to the far left side of the case. A solution would be to buy a thermalright AM4 bracket for Peerless Assassin Series so you can flip the heatsink perpendicular to the IO ports.
Saves you $$$$ from buying a new cooler or another mobo
와 갖고 싶다 빌드 잘보고 갑니다 멋지네요
actually you can put gigabyte eagle rtx 4070 ti without any mod and no need to remove the dust filter as well
Do you know if the PNY 4070 TI will work that way too? I'd prefer that card if possible as it's so quiet
@@thenewdesign have to be 2 slot with 58mm max of thickness. I think all of the PNY 4070 TI came with 3 slot. You can set the fan curve of Gigabyte Eagle RTX 4070 TI, make it more quiet than it's default.
@@dhajal Thanks! I ended up going w/ the MSI Ventus 4070 Ti OC which is apparently significantly smaller than even the Eagle, does really well w/ undervolting, and seems perfect for this case
@@thenewdesign cool! Yes undervolting 4070 TI are fun. My Eagle 4070 TI power consumption is now between 120w-168w. Depends on the game
당신은 한국 슾의 신입니다
So wear there no loud fan noise from you then with this build
nzxt h1 v1 후면패널도 핀 구조가 똑같을까요? 하나 구입해서 핀 제거후 전면에 달고싶은데... ㅠ 아 그리고 측면 먼지필터를 전면에도 부착해서 설치가능할까용?
Hi ,Great build : and i ask you :
1) i ve seen you can add 4080 FE only removing sdd case and “ cut” or replace 3 slot bracket and remove filter on H1.( 4070ti not great GPU for 4K )
2) i think you can change AIO with cooler master one for silent and temperature performance? Or add 280mm Aio with front/back cover custom ( easy to find on Etsy).
What about ?
완본체로밖에 판매가 안되는 케이스로 재탄생
빌드잘보고갑니다.
Haven't seen any like this before, really nice build. I'm quite interested and also want to re-make my own, btw what is the clearance for the cooler if you don't mind?
When removing the AIO radiator bracket and the internal dust filter, the cooler could be installed up to 99 mm high.
how does it compare to the stock cooler, is it cooler?
I replaced it with an air cooler to avoid pump noise and frequent pump failures. AIO cooler would be better for cooling performance.
Which thermal paste do you usually use for these? Love your vids btw!
I usually use XTC-4 thermal paste, which is cheap and has a lot of capacity.
Where can I buy the front mesh to replace the glass one
In Korea, the case vendor sells it separately. I don't know about overseas sales.
хороший канал спасибо
Lost Ark mokoko
Can this case install an SFX L (ROG LOKI 1000w)size power supply?
There is room for SFX-L standard power supply installation. (I think it's because the previous version was SFX-L standard power supply.) However, if you use a lot of modular cables, you may not have enough space.
Is it viable to keep the radiator mount and put a slim 140 mm fan on it?
To use the SI-100 as it was, the radiator mount bracket had to be removed due to a height issue.
If you use a 140mm slim pan, you don't have to remove the radiator mount bracket. However, CPU cooling performance can be significantly degraded.
@@DalraeMyo thank you
Hello do you think 120mm AIO will work better than this custom air cooling?
I don't know because I haven't installed a 120mm AIO cooler separately.
How did you swap out the stock nzxt psu? Did you have any issues with it, especially the the cables?
There was no problem with the operation, but the cooling fan noise bothered me, so I replaced the power supply. You can easily replace the power supply by removing the four screws on the power plug side of the power supply.
Does the Thermalright SI-100 fit in the V1 of this case?
Nice video!
H1 v1 can also be installed in the same way as the video.
how much actual cooler space is there, can it fit 115mm c14 s or wide alpenfom blackridge cooler?
@@danielvipin7163 Idk, you basically have to cut some claps in the case to fit it (like in the video), so I guess no space at all?
I'm using the fan that comes with the Cooler, but If you have in mind to use a smaller fan, I'm sure it will be some available space, and the case would not need to be touched.
In any case, the temps are good, and following the video it's all you need (and some patience while fiting everything in that tight space)
@@danielvipin7163 With the dust filter removed, the SI-100 could be installed at maximum and there was no free space.
how much actual clearance for cpu cooler is there, can this fit the nh c14 or alphenfom blackridge cooler?
100mm is the maximum height of the cooler with the dust filter removed.
@@DalraeMyo so c14 is a no go.
How much width and length we have?
@@danielvipin7163 The heat sink size of the SI-100 I used is as follows.
(L)120 x (W)108 x (H)74.8mm
* For horizontal and vertical sizes, there may be a size difference that can be mounted depending on the location of the CPU socket position.
HI , is it okay to use i5 13600k pair with TUF 4070ti using Astock z690M ITX DD4? coz im gonna use NZXT H1 V2 as well..... any advice?
Asrock z690M ITX may not perform well at 13600K because it can output up to 150W.
To mount the 4070ti TUF to the NZXT H1 v2, the dust filter on the panel must be removed and the latch securing the dust filter must be bent.
@@DalraeMyo oohh! soo wat mobo can I use to support i5 13600k sensei?
@@PiggyByt3 I recommend a motherboard with a power supply configuration of 600A or higher.
저도 비슷하게 제작을 하고 싶은데 cpu쿨러를 녹투아로 달게 되면 L12S 이런 거 달면 되는 걸까요? 아니면 조금 더 큰 쿨러를 달아도 상관 없을까요? 예산 상관없이 조용한 게 최우선이라서 저소음 공랭 찾다가 여기까지 왔네요 ㅎㅎ 아 CPU는 발열 적은 라이젠 7900 (Non X) 로 가려고 합니다
CPU 방열판의 높이가 쿨링팬을 포함하여 99mm 이하면 됩니다. 7900 Non-X의 경우 더작은 쿨러를 사용해도 됩니다.
@@DalraeMyo 그렇군요~ 감사합니다! 견적 짜는데 많은 도움이 됐어요
쿨링 성능 같은 경우 원래 있던 번들 수랭이 좋나요 아님 교체하신게 좋나요?
단순 소음 떼문에 교체하신지요
TDP 커버용량 자체는 수랭쿨러가 좋습니다. 저는 소음문제 때문에 교체했습니다.
@@DalraeMyo 조립 난이도는 많이 난해한가요..?
미들타워는 10번 넘게 해봤으나 itx 첨이여서
선정리 난이도,전반적 난이도가 그냥 게이밍 시스템 대중적인 dlx21같은데에 조립하는 난이도가 5라면 이건 어느 정도인지.. 알려주시면 너무너무 감사하겠습니다..!
@@Shoong03 NZXT H1의 경우 조립난이도는 ITX시스템중에선 굉장히 낮다고 생각합니다만 난이도는 개인차라고 생각합니다.
H1 난이도가 낮다고 느끼는 이유는 다음과 같습니다.
1. 기본 장착된 부속품들이 이미 반조립 상태에 기본적인 선정리가 되어있는 상태
2. 보드쪽 결합만 끝나고 그냥 선만꽂고 AIO 쿨러 결착 + 그래픽카드 장착만해주면 끝입니다.
@@DalraeMyo 그 선정리를 sf750으로
이미 충분하다 못해 좋은 시소닉 골드 750에서 플래티넘으로 한등급 올리시려고 25만원을 쓰시고 전부 재조립.. 존경합니다 물론 파워 소음 등의 원인도 있으셨갰죠
혹시 글카가 같으셔서 진짜 마지막 질문 드려봅니다. 4070ti벤투스에 신규 케이블이 적용 되고 화재 문제 때문에 결착을 잘해야하는것도 있지만, 3.5cm 거리 두고 꺽으라는데 간섭 문제는 없겠죠..? 너무 질문 드려서 죄송합니다 ..
Itx 첨 입덕한 쌉초보라 고수님의 조언이 필요해서
이때까지의 답변 너무 정말 많이 도움되었습니다
너무 정말 감사합니다 은인이십니다
@@Shoong03 저는 PC관련 이야기하는거 좋아해서 궁금하신건 얼마든지 질문하셔도 상관없습니다. 신규 커넥터 녹는건 제가 경험 해보지못해서 어떻게 답변드려야 될지모르겠습니다. 제가사용하는 커넥터는 커세어 파워 전용 케이블이라 (굉장히 뻣뻣합니다.) 그냥 구부린 대로 모양이 유지되길래 그대로 장착했습니다. 너무 심하게 한쪽으로만 힘이가해질정도만 아니면 될거같습니다.
해당제품 공랭 쿨러중 140MM 사이즈의 LP타입도 가능할까요?
높이만 되면 얼추 가능합니다. AIO 쿨러 떼고 그자리에 140mm 쿨링팬 다는 빌드도있습니다.
Nice Build! Rtx4080 FE will fit instead of a 4070ti..
Will it?? Just without the SSD tray and dust filter?
@thenewdesign yes but you have to bend the 3rd tab on the 4080's IO Shield/Mounting Bracket inwards to make it fit as the case only has 2 slots.
@@Restless2010 Thanks! I read Gigabyte makes an "Eagle" edition of the 4070TI that's physically smaller and requires no case modification. I might go w/ that since I'm putting a 13900KF in this anyway
화이트하면 공기 청정기로 볼 듯.
4:34 여기에서 mode3 150w 리밋을 사용하기로 했다고 하셨는데, 어떻게 설정하는건지 알수있을까요?
MSI 바이오스 -> OC탭 -> 어드밴스드 CPU 컨피그레이션 -> 숏/롱 듀레이션 파워 리밋에 150W 적으시고 그아래 CPU 라이트 로드는 Mode3를 선택했습니다. CPU 라이트 로드의 경우 CPU 수율에따라 Mode 값이 달라지니 Mode 9 부터 순차적으로 내려보시는걸 추천합니다. (내릴수록 전압을 많이 깎습니다.)
@@DalraeMyo 오호 어려운영역이네요 ㅎㅎ ASUS보드는 적용이 안되는건가요?
@@what_should_i_eat_today ASUS의 경우 명칭만 다르고 동일한 기능을 제공합니다. 단 MSI의 CLL처럼 Mode값을 선택하는게 아닌 오프셋 값으로 음수값을 직접 입력하셔야합니다.
V2에는 100mm 장착된다고 들었는데 해야될게 많네요
V1은 농협으로 가야되겠네요
CPU 쿨러 부분은 v1 v2 모두 동일한 높이로 알고있습니다.
v2에서 2mm 가량 커진 라디에이터가 v1에서 장착가능했던 튜닝메모리가 장착 불가가 된걸로 봐선 최대 장착가능 높이는 같은거같습니다.
@@DalraeMyo좋은 정보 감사합니다
Will the v1 fit that msi gpu?
혹시 상단에 부착한 흰색 펜 제품명 알 수 있을까요?
써멀라이트 TL-B9W라는 모델로 92mm쿨링팬중엔 가장 성능 좋은팬으로 알고있습니다.
@@DalraeMyo 감사합니다!
l12s가 아니고 sl100이었구나
저도 NZXT H1 V2 12900K + 3080슈프림 사용하고 있는데 케이스에 달린 1열 수냉 보다
현재 장착하신 공랭이 효율이 더 좋은건가요 ? 따로 실험을 해보셨을 까요?
추가적으로 CPU 언더볼팅 하는 방법도 알고 싶습니다 형님!
CPU 냉각성능은 LP공랭 쿨러보단 일체형 수랭쿨러가 더 좋습니다. (140mm 일체형 수랭쿨러의 경우 대략적으로 듀얼타워 대장급 공랭 쿨러 성능은 나옵니다.)
다만 절대적인 냉각 성능 외에 쿨러가 구동하는 소음에 저는 불편함을 느꼈고, 수랭 쿨러보단 공랭 쿨러를 선호하는 것도 있었기에 과감히 수랭 쿨러를 탈거하고 공랭 쿨러로 변경하였습니다.
CPU 언더볼팅의 경우 CPU마다 수율이 다르기 때문에 직접 안정적인 값을 찾으셔야 합니다. 언더볼팅하는 방법은 여러 가지가 있지만, 저는 귀찮아서 보드 제조사에서 제공하는 프리셋 값이나 CPU 전압 오프셋 설정을 주로 사용합니다.
@@DalraeMyo 와 asus 로 하는 기본 방법을 알 수 있을까요?
asus가 프리셋을 제공하는지는 모르겠습니다. 단순히 cpu 전압설정을 오프셋모드로 음수값을 입력해서 내릴순 있습니다. asus이 B칩셋을 사용하는 보드는 전압을 높이는건되는데 낮추는건 불가능한걸로 알고있습니다.(성능이 크게하락)
선구자입니다 ㄷㄷ
혹시 전면패널은 기본강화유리로 사용하면 온도가 높을까요?
열기를 배출할 면이 하나 줄어들게되니 아마 4면 메시패널보단 온도가 살짝 높아질것으로 예상됩니다.
@@DalraeMyo 네 감사합니다 포스팅한것도 정독하였습니다^^많이 안올라가면 그냥 기본으로 강화유리 사용할려고합니다 ㅎ ㅎ그리고 패널같은거 부품은 어디서 구입하는걸까요?
@@aires515 유통사 브라보텍 홈페이지에서 1:1문의하니 구매가 가능했습니다.
@@DalraeMyo 네 달래묘님 정보감사드리고 앞으로 변태?적인 실험 잘부탁드립니다 ㅋ.ㅋ
저는 axp120-x67 이쿨러에 25T똥투아로 작업해 볼 예정입니다! >.
펌프소음이 제일 시끄러웠는데.. 내껀 파워가 양품 이였나
하나둘씩소거법으로 저소음 부품으로 교체하다보니 거슬리게 되더라구요..ㅋㅋ;
번들 수냉 많이 시끄럽나요
펌프소리보다 수랭에 달린 팬이랑 파워 소음이 엄청납니다.
sf750, 녹투아로 교체하고 나면 펌프 고주파가 들려오죠. (펌프속도 조절불가)
그래서 소음에 민감하면 공랭이 답입니다 ㅎ
9w 차이인데 온도차가 20도가 나는게 좀 이상하긴하네요..
옅은 회색 그래프는 ATX 시스템에 240mm 수랭쿨러입니다.
짙은 회색 그래프는 ITX 시스템에 LP타입 공랭쿨러입니다.
Вышло охуенно, кореец братец