I had the same issue on my old qashqai’s 1.5dci engine when a glowplug failed. It had over 180,000 miles on it at that stage and I was dreading taking it out. But I did some prep work on it beforehand by soaking all the glowplugs in WD40 every day for a week after a drive when the cylinder head was hot and had expanded and so the WD40 could find its way down the glowplug threads and eat away the built up corrosion. So the big day came to take them out and first off, I slightly “tightened” the glowplugs to break any remaining corrosion and then slowly undid them. They all came out without any “squeaking” or hesitation despite being the original glowplugs that had been in the car 12 years. When I examined them, the glowplug threads were full of muck which was the now dissolved corrosion that the WD40 had done a job on. I’d say if I hadn’t done my prep work, they’d have all snapped in the cylinder head. I’ve gone back to petrol now as they’re much easier engines to work on.
Been there before with glow plugs, no point risking it if they feel terrible like you say. I normally fire some more deblock oil down the threads before I put everything back together so maybe next time it comes in the stuck ones have a chance of moving
Calm personified👍, you never loose your cool Baz 😁 . Bloody amazing especially in this hot 🥵 weather . You are like watching your best friend explaining the intricacies and technical details of modern vehicles 🚗… … 😁😁👏👏👍👍
When replacing glow plugs I douse them with penetrating oil, get the engine to temp put some more pen.oil and never had an issue they fly out so to speak. That's my 2 pennies worth...
I think glow plugs should be changed every 3 years on a service interval but obvs manafuctures don't bother I had to do them on my 1.6hdi Knocked the tip into the cylinder and used the lazer pick up magnet through the injector hole to fish it out
I have a Jaguar XE that had a failed glow plug, unfortunately the tip of the plug snapped off and scored the cylinder bore, Not a good day. It also had a burned exhaust valve and seat, as well as two burned/melted pistons. Not bad for 78000 miles.
I’ve had 3 JLR vehicles, an Évoque and 2 E Paces from new. Binned them all when they were out of warranty! I see so many JLR older vehicles running around as school/shopping hacks, one b big failure coils write off the. Car! Great content Baz, your sixth sense when trying to remove seized bits Is something you learn the hard way! 👍🇬🇧😎
I watched a video today on O' rileys autos where he had turbo overboost on a JLR AAabdcit was a sticking throttle body on the inlet, common problem apparently,just a thought.
Question, from a preventative maintenance perspective at what age would you generally replace glow plugs, whilst remembering/balancing the older the plugs are the more challenging they can be to extract ?
If you can get your glowplugs out and clean the treads and apply a small layer of anti seize to help stopping them sticking, and if your changing or removing plugs, get the engine hot is your best bet to get them out
With the glow plug been worn like that, would the under boost problem cause that? It would mess with the air to fuel ratio. Also, i fuckin hate glow plugs. So many are seized in. They should be changed regularly to stop massive problems in the future.
Generally glow plugs are only used for start ups to heat cylinders, which is why they can be such a pain on start up with bad plugs, From my experience I found with codes for under/over boost to check MAP sensor in manifold, diesels with EGRs love to cake the manifolds with sludge and carbon, or if the EGR cooler is leaking internally it’s mixing with the soot and going straight through your intake and can also block up exhaust pressure pipes and sensors
My neighbour bought same car 4 year ago ... but sadly he died. (RIP Peter) One of the last UK built before they moved to Slovakia. Now his Widow is starting to experience the same JLR design failures as this video ... Tut Tut Tut, be warned!
No good having tools without knowledge simple resistance test i use the autel camera autel 808 bt brilliant hd weldone keep up the good work from mcintechmobilemechanic
@@mike-s8n8y well it depends on the resistance of the bulb, but the voltage would actually be shared in a series circuit between both meaning if both consumers have the same resistance each consumer would have 6v but with different resistances on the consumers it could potentially supply the glow plug with more than 7v
So if the glow plug was high resistance and not a complete open circuit, it would draw all of the voltage potentially so the test lamp wouldn’t light up as the glow plug is consuming all of the voltage potentially melting it
P2bae-00 only relates to adblue level low. Bad description on non gen scan tools nox performance 🤦good to clean the injector though. turbo will be shagged. Glow plug will be melted, most likely high egt/combustion temp due to faulty injectors. Fekin ingeniboom. Landrover instructions state to remove inlet manifold to do plugs 😅 (tech at a Landrover specialist for my sins)
I had the same issue on my old qashqai’s 1.5dci engine when a glowplug failed. It had over 180,000 miles on it at that stage and I was dreading taking it out. But I did some prep work on it beforehand by soaking all the glowplugs in WD40 every day for a week after a drive when the cylinder head was hot and had expanded and so the WD40 could find its way down the glowplug threads and eat away the built up corrosion. So the big day came to take them out and first off, I slightly “tightened” the glowplugs to break any remaining corrosion and then slowly undid them. They all came out without any “squeaking” or hesitation despite being the original glowplugs that had been in the car 12 years. When I examined them, the glowplug threads were full of muck which was the now dissolved corrosion that the WD40 had done a job on. I’d say if I hadn’t done my prep work, they’d have all snapped in the cylinder head. I’ve gone back to petrol now as they’re much easier engines to work on.
Been there before with glow plugs, no point risking it if they feel terrible like you say. I normally fire some more deblock oil down the threads before I put everything back together so maybe next time it comes in the stuck ones have a chance of moving
Great content, as usual, it's the dilemma of owning a JLR.😮.
half the fun sorting them out .but i keep my pensioners bus pass up to date and a mountain bike to hand
Calm personified👍, you never loose your cool Baz 😁 . Bloody amazing especially in this hot 🥵 weather . You are like watching your best friend explaining the intricacies and technical details of modern vehicles 🚗… … 😁😁👏👏👍👍
Maybe that bit of the glow plug went into the turbocharger 🤔
I bet if you feel that turbo impeller it will have loads of lateral in and out movement.
When replacing glow plugs I douse them with penetrating oil, get the engine to temp put some more pen.oil and never had an issue they fly out so to speak. That's my 2 pennies worth...
I think glow plugs should be changed every 3 years on a service interval but obvs manafuctures don't bother
I had to do them on my 1.6hdi
Knocked the tip into the cylinder and used the lazer pick up magnet through the injector hole to fish it out
I have a Jaguar XE that had a failed glow plug, unfortunately the tip of the plug snapped off and scored the cylinder bore, Not a good day.
It also had a burned exhaust valve and seat, as well as two burned/melted pistons. Not bad for 78000 miles.
you would expect better
Has anyone else noticed the jungle growing in the workshop?
Nice job Baz. Those glow plugs can be a pain
Ad blue crystal clear from wynns prevents add blue crystalising,
better to use ad blue from the pump and not from containers as they can crystalise from storage and direct heat
I’ve had 3 JLR vehicles, an Évoque and 2 E Paces from new. Binned them all when they were out of warranty! I see so many JLR older vehicles running around as school/shopping hacks, one b big failure coils write off the. Car! Great content Baz, your sixth sense when trying to remove seized bits Is something you learn the hard way! 👍🇬🇧😎
I put some ad blu conditioner in my tank when filling up no problem, u can get from Europarts.
Sounds like Ric Flair Woooooooooooo
I watched a video today on O' rileys autos where he had turbo overboost on a JLR AAabdcit was a sticking throttle body on the inlet, common problem apparently,just a thought.
This was underboost no?
I regularly watch O Reilly’s RUclips channel. His channel is so helpful too. Like this one
@@ilovepikeysit was yes but it might be something to look at,?
Tdv6 only mostly gen 2 but have seen them stick gen1
Great job, love that new smoke machine 👍
It's unreal mate
Question, from a preventative maintenance perspective at what age would you generally replace glow plugs, whilst remembering/balancing the older the plugs are the more challenging they can be to extract ?
If you can get your glowplugs out and clean the treads and apply a small layer of anti seize to help stopping them sticking, and if your changing or removing plugs, get the engine hot is your best bet to get them out
Great video as always, just wanted to ask about that halogen test light, never seen one before, is there a specific use for it?
Loads testing buddy
With the glow plug been worn like that, would the under boost problem cause that? It would mess with the air to fuel ratio. Also, i fuckin hate glow plugs. So many are seized in. They should be changed regularly to stop massive problems in the future.
Today was a graft. Vacuum pump and servo on a discovery tdv6. Too hot for that shit.
Generally glow plugs are only used for start ups to heat cylinders, which is why they can be such a pain on start up with bad plugs, From my experience I found with codes for under/over boost to check MAP sensor in manifold, diesels with EGRs love to cake the manifolds with sludge and carbon, or if the EGR cooler is leaking internally it’s mixing with the soot and going straight through your intake and can also block up exhaust pressure pipes and sensors
i would pull no three injector .and test it
@williamgould2855 yeah a leaking injector or a bad spray pattern could also cause it.
My neighbour bought same car 4 year ago ... but sadly he died. (RIP Peter) One of the last UK built before they moved to Slovakia.
Now his Widow is starting to experience the same JLR design failures as this video ... Tut Tut Tut, be warned!
No good having tools without knowledge simple resistance test i use the autel camera autel 808 bt brilliant hd weldone keep up the good work from mcintechmobilemechanic
Was the glowplug springing?
Nope solid
If you look glow plugs are 7v not 12v most likely melted the tip with 12v down it, have made the same mistake before 😅
how would it do that ?
@@mike-s8n8y well it depends on the resistance of the bulb, but the voltage would actually be shared in a series circuit between both meaning if both consumers have the same resistance each consumer would have 6v but with different resistances on the consumers it could potentially supply the glow plug with more than 7v
So if the glow plug was high resistance and not a complete open circuit, it would draw all of the voltage potentially so the test lamp wouldn’t light up as the glow plug is consuming all of the voltage potentially melting it
How would you go about further diagnosis of that turbo?
take the intake pipe off and check the impeller for wear
Hi baz hoo buys all the nice tools for u
Nice scanner
You look really hot buddy.Take care in the heat.I hate it.
P2bae-00 only relates to adblue level low. Bad description on non gen scan tools nox performance 🤦good to clean the injector though. turbo will be shagged. Glow plug will be melted, most likely high egt/combustion temp due to faulty injectors. Fekin ingeniboom. Landrover instructions state to remove inlet manifold to do plugs 😅 (tech at a Landrover specialist for my sins)
That's a noise a ghost makes?
Wheres ya glasses
They do my head in when it's hot buddy so I wear contact lenses
How much is the computer mate
£5994 buddy
@@bazmeredithI'm due to buy another scanner this year. I've always had snap-on. Is it time for me to make the change?
@@ilovepikeys can't beat change and the launch does everything I need it to and is more capable than I will ever be!!!
@@bazmeredith Bloody hell that's a lot of money!😮