Thanks for the video. $30 DYI fix. The only difference with my daughter's vehicle is that the release for the connector was on the right side, so almost impossible to access with a screw driver. I ended up taking the clip off first. It was a breeze to take off the connector once the sensor was off. Note, the clip fits into two cutouts on either side of the tube that the sensor goes into. Make sure you put the prongs of the clip into them when you slide it into place.
Great video, I would suggest instead of Vaseline on the o ring which is a petroleum based product which deteriorates rubber, use di electric grease. It's silicon based, and will not deteriorate the rubber.
Exactly. And, never use silicone grease on silicone. Buna-N is mildly affected by oil, not like rubber though. Nitrile is impervious to most auto chemicals. I'm an automation and building mechanic, I use Tri-Flow for everything but silicone and good old original Chapstick or Vaseline for silicone.
Thank you for the great video, it fixed my problem. No more sounding like a space ship (fans winding up) as soon as you turn it on, no more check engine light, and I believe various aspects of the car will now run smoother. I have a few constructive comments. Like everyone else, the vaseline is a no....best is apparently silicone based grease which I bought at the home depot. Secondly, I did not remove that plastic engine cover, I don't see a benefit there, but I did remove the air filter box entirely (2 screws and unplug the MFS. Made it like working in my living room. Strangely, my coolant didn't come flowing out. I could see it there, but not enough to come out, which yes....I found that mildly concerning. I did not need a screw driver in the electrical connector, was made to unsnap by hand (yours might be too). The sensor rotates by hand and my snap was on the bottom side not front like yours. Thanks again!
Good video, except for the Vaseline part. Don’t every put petroleum products onto coolant parts: orings, seals, or hoses. Coolant orings hoses and seals are not petroleum resistant and with swell and deteriorate. Petroleum may only be used on oil seals, and gaskets: like valve cover gaskets or cam/ crank seals.
Yes. Use silicone lube. If you don't have any, you can buy a tiny packet at the auto parts store for about $1.00 and you will still have plenty left over.
Hi, my girlfriend got a new beetle from 2002 and the light of the coolant on the dashboard it's all the time on in a blue color. I read on internet that if it never turns off, it means that there is a problem in the electric system of that part. The only thing I can think about is the sensor. Would you have some idea about that? The car has an automathic gearbox and always changes so late, that's a reason too why I think is the sensor since the engine wants to warm up.. Thanks!
Use silicone for greasing or Windex for barb fitting on rubber and Buna-N, use Vaseline and never silicone on silicone rings and hose, and whatever is handy on nitrile. Pretty sure the cheap sensors use Buna-N and nitrile.
Here is a video on how to change a thermostat on a 2008 VW Beatle. And yes it is behind the Intake Manifold: ruclips.net/video/IAOePwgqrCY/видео.html Good luck...
Thank you so much for this video. I'm a 57 year old female and because of your video I was able to fix by myself. Thank you thank you thank you.
Thanks for the video. $30 DYI fix. The only difference with my daughter's vehicle is that the release for the connector was on the right side, so almost impossible to access with a screw driver. I ended up taking the clip off first. It was a breeze to take off the connector once the sensor was off.
Note, the clip fits into two cutouts on either side of the tube that the sensor goes into. Make sure you put the prongs of the clip into them when you slide it into place.
This fixed my problem with the hard start in the morning and my air conditioner blowing hot. Thank you
Great video, I would suggest instead of Vaseline on the o ring which is a petroleum based product which deteriorates rubber, use di electric grease. It's silicon based, and will not deteriorate the rubber.
Exactly. And, never use silicone grease on silicone. Buna-N is mildly affected by oil, not like rubber though. Nitrile is impervious to most auto chemicals. I'm an automation and building mechanic, I use Tri-Flow for everything but silicone and good old original Chapstick or Vaseline for silicone.
Thank you for the great video, it fixed my problem. No more sounding like a space ship (fans winding up) as soon as you turn it on, no more check engine light, and I believe various aspects of the car will now run smoother. I have a few constructive comments. Like everyone else, the vaseline is a no....best is apparently silicone based grease which I bought at the home depot. Secondly, I did not remove that plastic engine cover, I don't see a benefit there, but I did remove the air filter box entirely (2 screws and unplug the MFS. Made it like working in my living room. Strangely, my coolant didn't come flowing out. I could see it there, but not enough to come out, which yes....I found that mildly concerning. I did not need a screw driver in the electrical connector, was made to unsnap by hand (yours might be too). The sensor rotates by hand and my snap was on the bottom side not front like yours. Thanks again!
Thanks a lot for your video! Very informative and useful.
Thank you. I will be doing this as soon as part arrives
I never comment but I had to on this. Cudos to you! Well done calm DETAILED video . Much appreciated !
Thanks that help me alot
Great video!
What problems did this fix in the car. Thanks so much!
Good video, except for the Vaseline part. Don’t every put petroleum products onto coolant parts: orings, seals, or hoses. Coolant orings hoses and seals are not petroleum resistant and with swell and deteriorate. Petroleum may only be used on oil seals, and gaskets: like valve cover gaskets or cam/ crank seals.
Yes. Use silicone lube. If you don't have any, you can buy a tiny packet at the auto parts store for about $1.00 and you will still have plenty left over.
Would coolant temp sensor keep my 2010 vw bettle fans from working?
There a marking on how it goes in or u just push it in and put clip back on ??
Hi, my girlfriend got a new beetle from 2002 and the light of the coolant on the dashboard it's all the time on in a blue color. I read on internet that if it never turns off, it means that there is a problem in the electric system of that part. The only thing I can think about is the sensor. Would you have some idea about that?
The car has an automathic gearbox and always changes so late, that's a reason too why I think is the sensor since the engine wants to warm up..
Thanks!
Why are all the forums saying a broken coolant temp sensor is code P2181 for the 2.5 engine?
Take the cap off to release the pressure then put it back on before you remove the sensor. It will loose less coolant then
Yes, this way you only lose about a tablespoon of coolant. I placed a sock underneath it to catch it.
Use silicone for greasing or Windex for barb fitting on rubber and Buna-N, use Vaseline and never silicone on silicone rings and hose, and whatever is handy on nitrile. Pretty sure the cheap sensors use Buna-N and nitrile.
Will this make my fans stop blowing non-stop?
Does the clip have to go all the way in or it stay half way out
It goes back in exactly like it came out. It has indents inside the clip to make sure it stops and retains its place. No worries.
Does that sensor supposed to be turned in to fit properly? The sensor keeps shooting out when I start the car
That is what the metal clip is for.
@@boomerguy9935 The clip is actually plastic, but LOL YES the clip is necessary.
Are you in NJ can you fix my car, lol :( damn I'm paying out the ass for this car
Is this a problem to air condition blowing hot?
Alex. No. The problem is the loose nut behind your steering wheel causing hot air.
@@BobSmith-mc7uq please explain
Here is a video on how to change a thermostat on a 2008 VW Beatle. And yes it is behind the Intake Manifold: ruclips.net/video/IAOePwgqrCY/видео.html Good luck...
Are u mechanic