I will be sure to use your link for the laser machine. The exact machine you have, what else can you use it for? I took the quiz but got overwhelmed and hope you can kindly take a moment to answer my question :)
With the xtool s1 you can cut and engrave many materials. Since its a diode laser not all colors of acrylic can be cut. If you plan on working with more acrylic i recommend that Xtool p2.
This is very helpful, but there is one thing I’m caught up on. The bottom is smaller than the top but you used the top for your measurement. Since your design is a rectangle, how is it that the design elements on the bottom don’t end up overlapping?
Thank you so much for your help! I have a question, before starting the Red Cross on the screen is suppose to be where the laser starts right? So How do you align it to start engraving on the handle when the cross was in the middle? I’m a little confused
Hello :) I receive my S1 tomorrow and I can’t wait to give it a try. (I am the one who has the M1 and wrote you about it on Messenger). Have you tried the S1 with acrylic at all? I love how your Stanley came out it looks amazing!!
Hi! Thank you for this tutorial--it's very detailed and I appreciate that! I am wondering where to purchase the foil with sticky back? I am purchasing your cover for logo off your Etsy account, but need to find the foil with sticky back. Thank you!
20w better for engraving? Yes and no. You can adjust the power on the 40w. The 40w laser beam is bigger but I personally think it's better. I've herd of people with 20w using a spacer when framing to get that bigger beam focus. The comparison on engraving is hard to tell. Don't think you wasted your money on that 40w. You can cut deeper wood, acrylic ect
How long did it take to generate the image? I have a file very similar to yours. I know you said to be patient but we are at 40 minutes and it is still cycling,
We have been trying to get this process right for a while but we are having issues with the laser hitting the cup. We are using dupes but they are the same measurements. When we level the bottom the tabs hit the laser. Any suggestions?
I’ve set my distance for the highest part, the lowest part, and exactly how she stated in the video and each time the design comes out like crap on the side of the tumbler opposite to where I set the distance for.
@@ronr179 she says “measure right where the curve starts on the tumbler”. Which unfortunately I’ve done. I’ve also tried from the end of the taper as well. Both with similar crappy results unfortunately. I haven’t tried from the center of the taper like you’ve suggested. I’ll try that this evening. The only other way I could think to make this work would be to cut my design and do two separate runs with the engraving but then I would have to make sure to line the second go up perfectly which would be a headache.
Your distance measurement should be right where the curve starts? No... distance measured should be done right in the middle of the tapered area. Not at the beginning. Spreading knowledge to help others is key. I wonder how many people where disappointed when they engraved their $60 stanley and the engraving was burnt on the top from laser being 2.50mm closer then what it should of been 1.25mm away
I’ve watched your 2 tumbler tutorials over a dozen times you deserve 1000+ 👍🏽
This tumbler came out brutal I love itttttt..... Love the combo colors of this tumbler..... Amazing
Thank you so much 😀
I like how you just get to the point in your video. I am going to try a tumbler today
Thanks for this amazing video 🙌🏻🙌🏻because of you I’m doing my first tumbler 🫶🫶
Yayy! Thank you!🥰 so happy to hear this! Good luck!!💖
Wow 🤩 that came out stunning 😍 thanks for sharing your expertise on this 🩷💙🤍♥️ stay blessed love 🥰
Thank you so much 🤗
Thank you so much for sharing this tutorial. Been looking everywhere for some to explain on an xTool. U made it so easy.
If I tighten the chuck and put leveler on the bottom of tumbler the base rises up. Is that how you ran it with the base up on one side.
Love the your videos, could u please do one with just a 40oz regular powder coated video
Have you changed your settings for faster time but still great results? If so can you share the settings.
I will be sure to use your link for the laser machine. The exact machine you have, what else can you use it for? I took the quiz but got overwhelmed and hope you can kindly take a moment to answer my question :)
With the xtool s1 you can cut and engrave many materials. Since its a diode laser not all colors of acrylic can be cut. If you plan on working with more acrylic i recommend that Xtool p2.
This is very helpful, but there is one thing I’m caught up on. The bottom is smaller than the top but you used the top for your measurement. Since your design is a rectangle, how is it that the design elements on the bottom don’t end up overlapping?
Thank you so much for your help! I have a question, before starting the Red Cross on the screen is suppose to be where the laser starts right? So How do you align it to start engraving on the handle when the cross was in the middle? I’m a little confused
I still get so confused on where to make it so the cup starts by the handle nubs so it’s seamless
I watched your video again and got it!thank you so so much for your videos!
How. much for that please?
how. much do you chRG FOR THT?
Thank you for this! ♥🩷
Hello :) I receive my S1 tomorrow and I can’t wait to give it a try. (I am the one who has the M1 and wrote you about it on Messenger). Have you tried the S1 with acrylic at all? I love how your Stanley came out it looks amazing!!
Hi! Thank you for this tutorial--it's very detailed and I appreciate that! I am wondering where to purchase the foil with sticky back? I am purchasing your cover for logo off your Etsy account, but need to find the foil with sticky back. Thank you!
Aluminum foil tape😉
Is this a 40oz?
How did u get it to engrave around the Stanley logo
Do you have a link for this specific laser ? I’d love to get one myself
Link is in my bio. Its the xtool s1 20w with the rotary attachment.
Do you angle yours by 3 degrees?
Still cant figure this out, the laser just goes off the tumbler.
I have a 40w laser for the S1. Is the 20W diode better for tumblers? I noticed the tumbler options in the material setup is limited with the 40w. Thx
20w better for engraving? Yes and no. You can adjust the power on the 40w. The 40w laser beam is bigger but I personally think it's better. I've herd of people with 20w using a spacer when framing to get that bigger beam focus. The comparison on engraving is hard to tell. Don't think you wasted your money on that 40w. You can cut deeper wood, acrylic ect
How long did it take to generate the image? I have a file very similar to yours. I know you said to be patient but we are at 40 minutes and it is still cycling,
Oohhh thats too long. Mine took about 10min
Does anyone else have an issue of the chuck attachment lifting up while it is engraving?
Yes! This is my issue as well and I came here to see if there was any advise on this issue. Did you find a remedy?
Where did you get this design?
❤❤❤❤
We have been trying to get this process right for a while but we are having issues with the laser hitting the cup. We are using dupes but they are the same measurements. When we level the bottom the tabs hit the laser. Any suggestions?
Did u ever figure this out ? I am having the same issue .
@Makingstuffforfun I don't understand why your having that issue. Are you inputting the settings correctly?
Having the same issue even with the tabs bent down the laser frame hits the tabs if the bottom section is level
Would you be willing to share the svg for this?
It's 1.99 on etsy, and most only come with 1 file per person
the part you did not show is what everyone messes up on can you please show where you auto messured on the stanley
Auto measure right in the middle of the slant (where the size starts transitioning)
Which part of the tumbler do you focus your laser on to determine the height?
I do the highest point of the tumbler
I’ve set my distance for the highest part, the lowest part, and exactly how she stated in the video and each time the design comes out like crap on the side of the tumbler opposite to where I set the distance for.
@@AYYO_DoraI believe she says measure at the middle of the tapper
@@ronr179 she says “measure right where the curve starts on the tumbler”. Which unfortunately I’ve done. I’ve also tried from the end of the taper as well. Both with similar crappy results unfortunately. I haven’t tried from the center of the taper like you’ve suggested. I’ll try that this evening. The only other way I could think to make this work would be to cut my design and do two separate runs with the engraving but then I would have to make sure to line the second go up perfectly which would be a headache.
@@AYYO_Doraany luck? And I would make sure your tumbler is centered and level.
❤️❤️❤️
I need you affiliate code for the engraver
Please use my link in the description 🙏🏼 thank you so much.
❤❤❤❤❤
🥰
💞💕
❤❤❤❤💚💚💚💚💜💜💜💜💜💜💜
Thanks for watching!!🥰🥰
Your distance measurement should be right where the curve starts? No... distance measured should be done right in the middle of the tapered area. Not at the beginning. Spreading knowledge to help others is key. I wonder how many people where disappointed when they engraved their $60 stanley and the engraving was burnt on the top from laser being 2.50mm closer then what it should of been 1.25mm away
I'm showing what works for me. Do what works best for you.