Sir every video of yours is very instructive, made a water level control circuit with Esp32 with HC-SR04 from your channel, after watching your video I downloaded your project and made it, but the water label shows 100% no change and can't enter the setting Please let me know where the problem may be.
after long research we have a new technology to send data over dc lines so no need to connect 4 wires of ultrasonic module just use same dc line between module and MCU to supply module & get data
If it's in an environment where it's humid or corrosive, you could use level sensors of wire probes that detect a ground connection. I used three wires to make an automatic discharge pump to empty out a dehumidifier tank, very reliable and it just requires positioning two wires at the high level pump turn on point, and low level shut off point. Arduino pull-up on an input detects whenever the wire contacts the fluid, pulling it to ground. Very reliable and simple-
Hi. I connected everything as in your diagram. I uploaded the code to the nano and unfortunately the screen doesn't work. I have an LCD keypad shield, I connect VDD instead of the 5V mark, then the screen lights up. After connecting pin D3 to E in the screen, the screen turns off and blinks slightly. in no case can you see the subtitles on the screen. What could be wrong?
Wow, nice project. I am kinda working on a similar project for my final year project, I am trying to control the level of water in the sewer lift station, but I am struggling to determine the components for my prototype. Someone to please help me.
Hi brother can you please make same automatic water level indicator by using complete arduino nano board (without ultrasonic sensor) as you made on your other channel . because the circuit you gave on another channel is really very complicated. And i request you to please make it in the most simplest way as you can. I would be really grateful if you make it again by using complete arduino board.
Dear friends nice video... You share link of AliExpress. For components. And site is band in india so how can I order components from AliExpress... Please help and suggest..... alternative way....
Nice project. It's wonderful. Keep doing good. Thanks for sharing the file. Pls try do sine wave inverter which uses 4 pwm and also have LCD. I need a project like this.Hope you will ?
Bro, Post a new video, same concept, do only a small change that is add extra one component nrf24 transmitter module for control a motor without wire connection from water tank to starter..
@@KiyanisLabthanx to reply.. i've finished work your project same as your tutorial.. it's working good with HC-SR04 on simulation.. but when i use JSN-SR04T the distance read is wrong.. is it coz the distance of JSN-SR04T work range from 25 to 450cm..? while HC-SR04 work range from 2cm to 400cm..?
It's ok but it's not practical to install wire from bottom to top overhead tank....need 50 feet wire to install it will decrease the volt to sonar sensor...
hi, can your pls make the video with 16X04LCD for getting the result 1)Millimeter 2)Centimeter 3)Inches 4)Ft at the same time also CM, Inch, ft must read the decimal points too brother
dear friend very good project, let me know how to adjust the height of tank in code, ( changes in which line)
Sir every video of yours is very instructive, made a water level control circuit with Esp32 with HC-SR04 from your channel, after watching your video I downloaded your project and made it, but the water label shows 100% no change and can't enter the setting Please let me know where the problem may be.
How do you set the high water level? Or do you have to set the Ultrasonic unit close to the high point?
Shall we add a alarm buzzer with this project
It's very useful if the ultrasonic senser can connect with a wireless device
A.0.A is the same connection and code for arduino uno?
Dear brother ,
In water tank , there is darkness . My question , if ultrasonic sensor works in darkness or not ?
after long research we have a new technology to send data over dc lines so no need to connect 4 wires of ultrasonic module just use same dc line between module and MCU to supply module & get data
Hello sir,
Can you kindly explain the values in the code
After some days of use in such high humidity environment the ultrasonic sensor start corrosion and finally it's stop working
You are right bro for such condition there are waterproof sensors as well
@@KiyaniKiLabok then, can you make video using waterproof ultrasonic sensor?
soon bro
I think sensor circuit pcb catch moisture then effect working .
@@KiyanisLab I must wait
I use 30 ft length of wire for ultra sonic sensor. Is it work?
Doesn't the sensor corrodes when mounted inside the tank?
If it's in an environment where it's humid or corrosive, you could use level sensors of wire probes that detect a ground connection. I used three wires to make an automatic discharge pump to empty out a dehumidifier tank, very reliable and it just requires positioning two wires at the high level pump turn on point, and low level shut off point.
Arduino pull-up on an input detects whenever the wire contacts the fluid, pulling it to ground.
Very reliable and simple-
Just Finished the Project.! And its Working. Thanks Bro !
Welcome 👍
Hello how can I contact you because i have the same project to do
Sir how can i use this code for small size tank...for example tank hight 500 cm or 1000cm....
Hi. I connected everything as in your diagram. I uploaded the code to the nano and unfortunately the screen doesn't work. I have an LCD keypad shield, I connect VDD instead of the 5V mark, then the screen lights up. After connecting pin D3 to E in the screen, the screen turns off and blinks slightly. in no case can you see the subtitles on the screen. What could be wrong?
Awesome vedio bro
I want to do this project can u help me add a dry run protection also?
Awesome project, can the unit be used to empty a tank instead of fill one? Would this require a change to the sketch?
Can u pls implement with dry run protection with sonar sensor reading & timing based.
What do you call the part that you plug all the wires into and then solder to the pcb? where do you get them?
Wow, nice project. I am kinda working on a similar project for my final year project, I am trying to control the level of water in the sewer lift station, but I am struggling to determine the components for my prototype. Someone to please help me.
Sir apni tanky kay lihaaz say code mein changing karni hogi kia.
Nai jab sensor fix karlo to tank ko empty kar k controller ko auto mode pe kar k push button press karne se tank size set ho jai ga
Thank you sir❤
wont have any problem on the snsor with moving water??
helo friend, project is great.
You can add Dryrun protect and use waterproof ultrasonic sensor, please!
hello there, can this measure distance of water form top with respect to time
why you didn't use Water sensor?
water proof is also the same
If I use a water level sensor, what cable do I need to change
Hi brother can you please make same automatic water level indicator by using complete arduino nano board (without ultrasonic sensor) as you made on your other channel . because the circuit you gave on another channel is really very complicated. And i request you to please make it in the most simplest way as you can. I would be really grateful if you make it again by using complete arduino board.
Bhai please reply
Please give me a method to connect the ultrasonic senser wireless using nrf24L01 or other device.
Thanks
ok soon bro
Dear friends nice video...
You share link of AliExpress. For components. And site is band in india so how can I order components from AliExpress...
Please help and suggest..... alternative way....
Nice project. It's wonderful. Keep doing good. Thanks for sharing the file. Pls try do sine wave inverter which uses 4 pwm and also have LCD. I need a project like this.Hope you will ?
Ok I will try
@@KiyanisLab thanks. I will expect it.
Becoz its working near in water, how make it hc sr04 module water prove? Tx mr
its water proof version is available you can use it
@@KiyanisLab i know that sir, but i want modified sr04 into waterprove sir
Which pump did you use for ultrasonic sensor
Nice project
How much percentage required to switch on the water pump
I'm not able to use that Garber file, I don't know why?
Awesome
Nice project sir
Thank you sir
Ultrasonic module how many meter maximum?
How can we impliment in AC motor in the home
Hard level
verry good
The link for 1 X Arduino Nano is wrong.
Hi, can you add a temperature sensor at the project ?
Ultrasonic 30 sm Motor off hona chaina to code kya Cheng kare?
Water tank height adjustment code change details
Sir how to change %
I mean it's show 4 8 12 16 18%
I near it's show 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 %
Hai sir ultrasonics sensor long wire connect sensor singl lost probleam alive details
Bro, Post a new video, same concept, do only a small change that is add extra one component nrf24 transmitter module for control a motor without wire connection from water tank to starter..
Please Sir did you write the code your self?
How to set tank size
Can i use arduino uno instead of arduino nano
yes you can
Please can you send me the connections how or they are the same?
Bro, can you plz provide the pcb's design file.
Simples form basic ardino project ki jankari do jiye sir
ruclips.net/video/tK9krFxTgCc/видео.html
Can we buy from india now ??
Instrument switch use pump on off
Push button can use for manual auto is better
WATR_LVL_ULT.ino:2:23: fatal error: Countimer.h: No such file or directory
I have downloaded this zip then also showing no such file .
Please reply
there is a text file as well use it
Ok
can i purchased this project
if i change the HC-SR04 with JSN-SR04T / AJ-SR04M, is the code still work..?
yes it will work
@@KiyanisLabthanx to reply.. i've finished work your project same as your tutorial.. it's working good with HC-SR04 on simulation.. but when i use JSN-SR04T the distance read is wrong.. is it coz the distance of JSN-SR04T work range from 25 to 450cm..? while HC-SR04 work range from 2cm to 400cm..?
Price this tool
Price this project
Bro can I get the code you have used for it
Is same code and diagram for Arduino uno???
yes bro
It's ok but it's not practical to install wire from bottom to top overhead tank....need 50 feet wire to install it will decrease the volt to sonar sensor...
can i use this code using arduino uno ?
yes
Hi how to put code
hi, can your pls make the video with 16X04LCD for getting the result 1)Millimeter 2)Centimeter 3)Inches 4)Ft at the same time
also CM, Inch, ft must read the decimal points too brother
Nice job, but i will like to include GSM notification.
please help!
Yes, sure soon i will
Only model
Can not use in real tank
اسلام علیکم بھائی lcd1604 with water bar code send me plz
soon bro
And the code is where?
link is in the description
Link doesn’t work for me just downloads a picture of the file name WATR_LVL_ULT.1 what good is that?
Can i purchase this from you?
contact me on fb bro
@@KiyanisLab fb link plz?
facebook.com/Kiyanis-Lab-1520512291502452/
At 09 project bro
This code low lavel set programe
Can you provide its loaded program file.
its in the description bro
Not good ,because You did not showing code.
its in the description bro
Nice project