Hi Girish, super work, I am in UK, but visit my ancestral home in India and have 300 litre tank due to poor pipe work, I always suffer from empty tank, now I will follow your project and install, for peace of mind, thanks a million, please forward any mods or information to us, being a programmer and computer addict, you have compiled a superb programing arduino sketch, I am now building this project thanks to einstein like you, grateful
Hello, in the video your connections to LCD are going to | analog in | on the board, the code you included says to go to the digital pins. I think the board in the video was inverted when you made the video. Cheers and thanks for the video!
The Question is that its a proto type what if the water creates humidity and the lid of the tank is cover what will happen to the sensor (sonars). Plz do answer
Hello , sorry I want to ask about this project , where is the code for this video? Because I open the link , the code is different from this video project.. Thanks
Hey there i need some help regarding auto switching of 2 airpumps for my fish tank, i.e. only one airpump is given power and both are connected in parallel, with only one air pump working at one given point of time, now at the time when one of the pumps stop working, i want the other pump to start automatically without any manual intervention.
Sir the program is not compiling .so please give any suggestions for it. We can't see any mail id in the description .sir please give any solution.we are in trouble.😫😫😫😫😫
don't use 4 wires in water...with time wire will caught corrosion and won't sense well..instead use level sensors like this > www.electronicscomp.com/anti-corrosion-water-level-sensor-with-ball-float-switch?gclid=Cj0KCQjwk4yGBhDQARIsACGfAeu75thYajJO24VSaT6dSDj8zdpncPDAqWLiQpKUvoiOSuq_vuiYgNwaAi-vEALw_wcB
Its a tank project. Pls Make a project on corporation water supply. When water available in pipeline and in tank water is low than motor start automatic and when its full motor stop automatic.
Hey man, the VSS (pin 1) and VDD (pin 2) of the LCD are inverted in your scheme and this will short-circuit the board. The RW pin is not connected anywhere and this will cause the display to don't show anything! In the new video with the dry pump run protection instead the pins are correct :)
@@Naughat I think sonar sensor gets rust dur to moisture and also many say sonar sensor doesn't work in closed space...@naughat if you get the ans please let me know too? I am thinking of using waterproof submersible probes? what about you? have you found any workaround?
how to make water level percentage on the tank (5% 6% 7% ~ 20% 21% 22% ~ 100% Tank full will be overflow) instead of low high column indication on display... please give me the code...
❤️سبحان اللہ وبحمدہٖ💚ALLAHKAREEM KE RAHMET KE INTAHA ♥️ درس حدیث: (ایک مومن کو پروردگارعالم سے ہمیشہ حسن گمان رکھنا چاہئیے کہ وہ عفوو درگذر کا معاملہ فرمائے گا) حضرت جابربن عبدالله رضى الله عنه سے روایت ہےکہ "میں نے رسول الله صلى الله عليه وآلہ وسلم کو، آپ کی وفات سے تین دن پہلے یہ ارشاد فرماتے ہوۓ سنا کہ تم میں سے ہرشخص کو موت اس حال میں آئے کہ وہ الله تعالیٰ سے حسن گمان رکھتا ہو۔ (مسلم حدیث 2877 ابوداؤد حدیث 3113 ابن ماجہ حدیث 4167)
If you have the LCD1602 you need to connect the RW pin of the LCD to Ground and you need also to adjust the chars brightness with the 10K potentiometer
I tried to replicate the sketch and the build. Once it was loaded onto my arduino, it broke and same happened with my 2nd board. Now I'm not able to upload any more sketches.
the schematic is wrong: you connect 12 volts on the USB connector: the board is dead. you connect the LCD on the wrong port on the board: they are on analog ones. your connection to 240 volts is insane. where can one download the codes?
Please contact through the email address mentioned in the video description. Let me inform you that it may cost you to get a copy of the original codes.
There is some mistake in the circuit......A variable resistor has only three terminals, but they have connected the wire as if there were 5 terminals.....
Please refer this video: ruclips.net/video/0XvcTOI3-1Y/видео.html
Hi Girish, super work, I am in UK, but visit my ancestral home in India and have 300 litre tank due to poor pipe work, I always suffer from empty tank, now I will follow your project and install, for peace of mind, thanks a million, please forward any mods or information to us, being a programmer and computer addict, you have compiled a superb programing arduino sketch, I am now building this project thanks to einstein like you, grateful
Short distance wiring pe to theek hai bhai, par long wires pe ye sensors kaam karenge. 5 v ka current 10mtr wire pe travel karke 2v hi bachega
Will this work under 80-90 degree temp?
can we use this in a petrol tank? please explain me.
Hello, in the video your connections to LCD are going to | analog in | on the board, the code you included says to go to the digital pins. I think the board in the video was inverted when you made the video. Cheers and thanks for the video!
Please provide the code for this... I'm doing this but not working
The Question is that its a proto type what if the water creates humidity and the lid of the tank is cover what will happen to the sensor (sonars). Plz do answer
I made it but a few extras like liter counting and automaic or manuel liter input stop. Thanks for the video.
Sonar sensors doesn't work in a close space I.e. water well or tank
Then what are the alternatives pls tell ?
This circuit is very insane
Hello , sorry I want to ask about this project , where is the code for this video?
Because I open the link , the code is different from this video project..
Thanks
What happened to the 10K variable resistor you showed in the components list?
cool project but what happen to safety , putting loose wire in mains plug !!!! and near a water bucket !
its Awesome, Thank you, From India
Thank you, the pleasure is ours.. From India too Pradeep!
can we use this circuit arrangement for large pumps too?
what is rating of connecting wires
how to arrange the code high water and the buzzer turn on and arrange it to high water and the water pump gonna turn on
Hey there i need some help regarding auto switching of 2 airpumps for my fish tank, i.e. only one airpump is given power and both are connected in parallel, with only one air pump working at one given point of time, now at the time when one of the pumps stop working, i want the other pump to start automatically without any manual intervention.
bro your arduino program in link is for 8 pump ...where is link for automatic water level
plz voice kis app se recording kiti aa
Sir the program is not compiling .so please give any suggestions for it. We can't see any mail id in the description .sir please give any solution.we are in trouble.😫😫😫😫😫
CAN YOU PLEASE GIVE ME THE CODE FOR THIS PROJECT(THE ONE GIVEN IN THE VIDEO)
its nice and grate projuct but this sysytem not work on dark places
amazing project could you please provide sketch for I2C 16 x02 disply..
yes...
i guess I am quite randomly asking but do anyone know of a good place to watch newly released series online ?
@Roger Cash Try FlixZone. You can find it on google :)
@Andre Jaxon Definitely, have been using flixzone for since april myself =)
@Andre Jaxon thanks, I signed up and it seems to work :) I really appreciate it !!
can i do this for big submersible pump for home????
please tell me. i want to apply this at my home.
Hi Ataur, I would request you to wait for little time. I will be publishing an advance video on same topic.
Here we Go! Please visit link for the same
ruclips.net/video/0XvcTOI3-1Y/видео.html
Hi there.
Can i please get the code for this original project. I know there is a updated one but i am looking for this spesific project code
same here sir
Brother can you please make one project like this without using ultrasonic sensor.... By just using 4 wires which will ne dipped in water
don't use 4 wires in water...with time wire will caught corrosion and won't sense well..instead use level sensors like this > www.electronicscomp.com/anti-corrosion-water-level-sensor-with-ball-float-switch?gclid=Cj0KCQjwk4yGBhDQARIsACGfAeu75thYajJO24VSaT6dSDj8zdpncPDAqWLiQpKUvoiOSuq_vuiYgNwaAi-vEALw_wcB
Can you help me out with the lcd issue, i also saw your new video on this, but this is much easier
2:43 which software you used to draw this circuit
you can do the same in microsoft excel or visio
ultrasonic sensor will get moister and does it works for long life ?
You can use JSN HC-SR04T its waterproof.
how is the crcuit looks like if it has ac connection ?
Sir which pump used in this projects plz tell me
can u make a tutorial to coding the arduino?
Ultra sonic sensor doesn't work in a close water tank due to moisture.
Excellent project. Can I use the scheme and the programming with Arduino Nano version 3.0? Thank you.
For practical use, this relay is not enough for contolling water pump and also wireless connections are needed as the wiring is away from tank.
In the circuit diagram you have used singe channel relay
But application you are using 4 channel relay.
What should i use??? Please reply soon
Can i use single channel relay??
yes, you can
Hey MiKo. Have you completed this project yet? If so, do you know what the 10K variable resistor is used for? Thanks!
cobyup10 i don't have this project, I only answer. I don't see rezistor on this project. I think, IT is not necessary
OK thanks MiKo. I guess I'll just go without it for now and track one down later if necessary.
Its a tank project. Pls Make a project on corporation water supply. When water available in pipeline and in tank water is low than motor start automatic and when its full motor stop automatic.
can the sensor take reading through plastic? the kind of qpaque plastic found in small motor fuel tank?
Can i use Arduino Nano with same Code and Connection diagram? And how to protect from dry run?
Sure, you can. I will be publishing a video on same topic very soon. Please stay tuned
Here we go, please find the link for the Video with dry Pump run protection
ruclips.net/video/0XvcTOI3-1Y/видео.html
what relay did u use 12v or 5v relay
Hey man, the VSS (pin 1) and VDD (pin 2) of the LCD are inverted in your scheme and this will short-circuit the board. The RW pin is not connected anywhere and this will cause the display to don't show anything! In the new video with the dry pump run protection instead the pins are correct :)
I would request you to follow the Diagram shown in my new video
ruclips.net/video/0XvcTOI3-1Y/видео.html
iam stuck up with LCD ...there is no display ..what are THE Corrections in the circuit diagram ?pls reply.
Sonar sensor, can it transmit signal over 60 to 70 meter?
use rx tx module
Can anyone think of a way to deploy this to a non-rigid water container, ie a sack/bag?
Hi sir, You remove percentage from last movie, Why sir?
good day sir. could you please sent me the code. its for my final year project at my university. really hope that u can sent me the code.
Good demo but practically it is useless as in the water tank moist environment will district the sensor in few days
can you tell the exact model of the motor pump ?
please can i get bthe code for this project
Where is the link for aurdino codes
Can you please send me the code? And what programme did you use for the circuit diagram?
😭😭😭😭
if the ultrasound did not use, it still can be function?
Can we use dc motor
How can I include a dry run protection for this circuit? Please help me
I am working on same feature. Will be publishing a new video. Stay tuned
@@TexoBot can you send me the link sir?
i try to do this project but my ultrasonic sensor cannot detect the water level why ? is it your coding problem or problem with connection
I m having the same problem, can you tell how did you resolved or not ??
sonar sensor is not suitable for house tank, just for hobby project
why ?
@@Naughat I think sonar sensor gets rust dur to moisture and also many say sonar sensor doesn't work in closed space...@naughat if you get the ans please let me know too? I am thinking of using waterproof submersible probes? what about you? have you found any workaround?
can i get proteus circuit of this prac???
💚سبحان الله♥️لَآ اِلٰهَ اِلَّا اللّٰه🌹
This project I want to connect to cloud... Please help @TexoBot
@Robots- The Next Species On Earth
Awesome video
How to do this without arduino?
hello can you please give me the full code used in the programing
hey long ago - be inquisitive and you would have seen show more guess what it points?
how to make water level percentage on the tank (5% 6% 7% ~ 20% 21% 22% ~ 100% Tank full will be overflow) instead of low high column indication on display... please give me the code...
Please check the new video, you will get that option
ruclips.net/video/0XvcTOI3-1Y/видео.html
Not good for long term... because of moisture or water steam content Ultra Sonic sensor will go bad :-(
How make this with arduino nano and also as wireless.
Kowshik Hero ..Hi I also want to make same project with 2 wireless sensors. if u have any updates plz let me know.
fantastic project...can you pl share the code
❤️سبحان اللہ وبحمدہٖ💚ALLAHKAREEM KE RAHMET KE INTAHA ♥️ درس حدیث:
(ایک مومن کو پروردگارعالم سے ہمیشہ حسن گمان رکھنا چاہئیے کہ وہ عفوو درگذر کا معاملہ فرمائے گا)
حضرت جابربن عبدالله رضى الله عنه سے روایت ہےکہ
"میں نے رسول الله صلى الله عليه وآلہ وسلم کو، آپ کی وفات سے تین دن پہلے یہ ارشاد فرماتے ہوۓ سنا کہ
تم میں سے ہرشخص کو موت اس حال میں آئے کہ وہ الله تعالیٰ سے حسن گمان رکھتا ہو۔
(مسلم حدیث 2877
ابوداؤد حدیث 3113
ابن ماجہ حدیث 4167)
Is it work if I connect 20ft wire distance
ss use lan cable cat 4 or cate 5 or telephone cable
This is good, but when you will put it in a real tank, soon the US sensor will corrode and it will become useless.
no.. I am using thi for last 1 year no corrosion at all beacuse sonar made of aluminium and i am using box with it
Wonderful projets. Please how can I get the arduino code for this projet 🙏🏼😭
please write to us. the email address is in the description.
Ok
Could you please send code in the video
Programming BHI add Kar dete detail me
Provide ardino sketch link
sir
I used the same code and code and programming , but lcd not working.
I have the same problem as you..Do you may have any updates on this?
If you have the LCD1602 you need to connect the RW pin of the LCD to Ground and you need also to adjust the chars brightness with the 10K potentiometer
Links not working, update please!
hello i made this project , it is working properly but it is 4 level and but i need 8 level plz help me
Sir plz help me, help me with the diagram as well as the codes.
Who ampere adavtor ?????
visit www.texobot.com/
I tried to replicate the sketch and the build. Once it was loaded onto my arduino, it broke and same happened with my 2nd board. Now I'm not able to upload any more sketches.
good job
Bro plz give Arduino code. Link not responding
What's the name and model of this arduino uno ??
it's arduino UNO r3
السلام علیکم ورحمتہ اللہ وبرکاته
سبحان اللہ وبحمدہ سبحان اللہ العظیم
سبحان اللہ وبحمدہ
can you please provide the gerber file ...
Program is not compiling please send the program
the schematic is wrong: you connect 12 volts on the USB connector: the board is dead.
you connect the LCD on the wrong port on the board: they are on analog ones.
your connection to 240 volts is insane.
where can one download the codes?
Can we get a project report of this project
I want a quick reply plzzzz
@@_S_Y_J____ please email us your requirements and we can look into it. The email address is in the video description.
sayoojm420@gmail.com
I need code and circuit diagram for arduino uno . Please send me code and circuit diagram for uno
your good project but i need the that has been connect the devise
hi i need the original code, can you give?
Please contact through the email address mentioned in the video description. Let me inform you that it may cost you to get a copy of the original codes.
Please provide your code..I need this argently..
I asked him a thousand times and he didn't gave.its just a dump channel.
Very nice
Thanks
Please give me the old water tank controller code please. I pay money 💵.. Please
the relay is not working plzz help regarding the code.
check the relay driver circuit
@@electrowindiyhacks6972 couldn't get it..! is the code Working?
abhinash agasti yes. The code and circuit is working without any problem
provide the code mention in the video
What if we didn't connect display
it should work. but if u dont wanna connect display then go for float switch instead.
I have tried this, lcd is not working, rest is fine its working
Is the code working?
Sir can u send code or program to it
in the code it is showing that it is NewPing: no such file is directory
Download the library and search newping library in google andbdowload the zip file.. Then add it to ur arduino software
YOUR CODE LINK IS WORNG PLS PROVED RIGT LINK
There is some mistake in the circuit......A variable resistor has only three terminals, but they have connected the wire as if there were 5 terminals.....