Amazing How to make free energy Water Pump | Auto Pump Deep Big River 24h/day NO Electricity

Поделиться
HTML-код
  • Опубликовано: 27 ноя 2024

Комментарии • 834

  • @angnhanpham9600
    @angnhanpham9600 Год назад +11

    Đây là 1 thí nghiệm hài hước nhất tôi từng thấy 😂😂. Bạn chỉ cần một đường ống nước và bỏ qua cái thùng phuy ( bình tích áp) thì nước vẫn chảy vì nước phía đầu ra thấp hơn mực nước ở đầu vào

  • @mahess1000
    @mahess1000 Год назад +40

    Great idea....The output water volume is greater than the input water volume due to the pipe diameter for the output compare to the input. May be inverting the pipe size or using same pipe diameter for both input and output will resolve the issue.

    • @blessed1sj
      @blessed1sj Год назад +3

      Always have twice suction pipe as discharge.

    • @РахматуллаПиров
      @РахматуллаПиров Год назад

      ,

    • @armsteadyrovally6478
      @armsteadyrovally6478 Год назад +8

      @Sewing-Hacks Yes you are right but the water going out is much more than the intake that is why the drum being sucked by the outlet water pressure. Just my thinking. need pressure guage to asertain the truth.

    • @nasro2421
      @nasro2421 8 месяцев назад +1

      هذا صحيح اختلاف في الحجم أدى إلى اختلاف في الظغط

    • @yowekemos2549
      @yowekemos2549 5 месяцев назад

      Also this design muggr have created higher pressure.

  • @FromSaultoPaul
    @FromSaultoPaul Год назад +7

    GREAT video and shows the power of water.

  • @buzzzkill9183
    @buzzzkill9183 2 года назад +9

    you prove it has great potential to move water. very good.

    • @fadilibya99
      @fadilibya99 2 года назад +2

      You are correct, but you need to balance the pressure

  • @oranghingel3980
    @oranghingel3980 11 месяцев назад +7

    It's not about releasing the air pressure from the drum, but allowing some air into the drum into the vacuum inside the drum will save that drum from squashing because the rate of discharge is higher than the rate of intake thus vacuum is created within the drum,unless there's some hole or cap for some air to fill the vacuum space, the drum will not squash in like this.
    The intake and discharge rate are not regulated.

  • @patrickmusgrove2876
    @patrickmusgrove2876 Год назад +4

    Excuse me sir. The drum fold up because the end of the pipe in the water was stuck in the mud. This can happen to the world largest drum. It is a vacuum like a black hole in space. Nice video. Now the world will change forever.

    • @Mrsunrisezero
      @Mrsunrisezero 7 месяцев назад

      he said that he hears the water running inside ... there is another reason and it can be corrected either by closing the water coming out or by putting a biggerr inlet pipe from the river ....

  • @jimmyolandia162
    @jimmyolandia162 Год назад +6

    Good job.I think one more thing to reduce the water output pressure is to close the outlet valve halfway to regulate the water flow.Another thing is to elevate the slope of the output pipe to reduce the water flow.I liked idea

    • @michaelchin6626
      @michaelchin6626 Год назад +2

      Try with the inlet pipe diameter LARGER than that of the outlet, to prevent a NEGATIVE PRESSURE to form inside the drum creating a DP (differential pressure) between the atmospheric pressure and the drum internal negative pressure. The drum will implode and COLLAPSED when the DP overcomes the drum metallic resistant force.
      Engineer cum scientist.

  • @shemvirgo9470
    @shemvirgo9470 Год назад +2

    this is truly not a fake video, I salute you brother, good work for showing the truth.

  • @franklinbperaltajr2717
    @franklinbperaltajr2717 2 года назад +13

    A simple siphon because, the level of the river is the same with the tip of the outlet pipe. Now to prove the effectivity of the device install in a deep well 6 Meters depth inorder to prove the effectivity. Thank you.

    • @benedictwamala6304
      @benedictwamala6304 7 месяцев назад +2

      Can this system pump water up the hill?

    • @kwasibrains287
      @kwasibrains287 6 месяцев назад +1

      No it can't but you can use the ram which also doesn't use power to pump up after this has suck from the river

    • @gianbattista
      @gianbattista 4 месяца назад

      cosa vuoi che dimostra è un buffone

    • @morningstar5177
      @morningstar5177 3 месяца назад

      @@benedictwamala6304 Yes if the hill is on middle of system.

    • @morningstar5177
      @morningstar5177 3 месяца назад

      @@kwasibrains287Is about level yes is can do this.

  • @nelsonantunes5404
    @nelsonantunes5404 6 месяцев назад +4

    I believe you should have left the tube that drains the water from the river full and covered, and opened it a little after you opened the outlet valve. Excellent video!!!

  • @AwahManga
    @AwahManga 9 месяцев назад +3

    This is one of the best video as it is it teaches the viewers a great lesson thanks

  • @paulsun8546
    @paulsun8546 2 года назад +6

    Halloo thanks so much, GOD BLESS YOU.

  • @choironcoi6232
    @choironcoi6232 2 года назад +3

    Mantab ngajak penonton jadi pintar, semangaatt..

  • @charlesdiaz6974
    @charlesdiaz6974 2 года назад +8

    Thank you my friend for showing your video we appreciate it don't take it so hard at least you're trying keep trying until you get it right you're doing a good job we watching your video we grateful you're very smart maybe if you use the Drone that will be stronger the steals the weak it means you're doing a good job it's just a material is not strong for you doing great first time watching your video I'm very impressed with your idea thank you for sharing

    • @satishloke
      @satishloke 2 года назад +1

      No problem with drum material, the problem is designe. Inlet water pipe is smaller , so the atmospheric pressure on drum was too much, when it's vacuum in side the drum. That vacuum tried to suck the water, but it could not supply that much water at that speed. Just keep in mind that inlet pipe must be big diameter nhan outlet. Other wise any drum will collapse no matter how strong you take.

    • @JavierJrSuico
      @JavierJrSuico 2 года назад

      buy another drum

  • @АлександрДегтярев-л7б

    Достичь такого давления которое ломает металлические бочки, это круто!!!! Сам проэксперементирую с применением манометр и всех замеров.

    • @gianbattista
      @gianbattista 4 месяца назад

      chi p èiu imbecille l'imbecille o chi ascolta l'imbecille? questo è il problema

  • @ozgaming8000
    @ozgaming8000 2 года назад +10

    Hopefully this person is HEALTHY ALWAYS all his sustenance affairs are made easy, greetings from a beginner youtuber bro 🙏

  • @yoskid3646
    @yoskid3646 Год назад +2

    The pressure is so powerful which causes the drum deformed. Kudos to this guy!

  • @yegammairamanathan7780
    @yegammairamanathan7780 2 года назад +2

    நல்ல முயற்சி !!

  • @kikoyyoutubetv8206
    @kikoyyoutubetv8206 7 месяцев назад

    Always try until you get perfect thanks for sharing friend watching from Canada 🇨🇦 orig from Bohol Philippines 🇵🇭

  • @test1280
    @test1280 2 года назад +7

    Vraiment un grand bravo pour le projet qui fonctionne très bien même tellement bien fait qu'il y a un tel tirage d'air que le tonneau n'a pas supporté !??
    Il m'était arrivé plus où moins là même chose par rapport au réservoir (tonneau) quand j'avais bricolé une pompe à vide avec un moteur de frigo !
    Mais vraiment bravo à vous !

  • @dattatraypatil2692
    @dattatraypatil2692 2 года назад +3

    You have done very Good demostration.

  • @wb-sv8sn
    @wb-sv8sn Год назад

    عمل رائع وفكرة ممتازة ستغير ثقافة جلب المياه مستقبلا وتحل كثير من المشاكل ... فى هذه التجربة اعتقد ان ما حدث قفل الطمى للانبوب الداخل ...

  • @krmben4453
    @krmben4453 2 года назад +7

    I think The problem is. The out flow pipe is very large so depressed air inside the drum is strong, that's why the drum is deformed .
    Trie to change the large pipe to narrow one.
    👍 Good luck

    • @lsubbareddy5131
      @lsubbareddy5131 Год назад

      Exactly,or put a pipe to inlet,as same diametre of outlet and outlet length to be reduced.

  • @douglasp.shepherd3396
    @douglasp.shepherd3396 2 года назад +12

    The vaccum being formed in the drum is to generate a suction from the inflow pipe.But, the outflow pipe should be only slightly thicker ie 1''pipe is to 1.1/4". This ratio will prevent the drum from collapse 👍🙏

    • @shanew3595
      @shanew3595 2 года назад +3

      I saw that too. output is too big for intake causing high vacuum.

    • @shhs1791
      @shhs1791 2 года назад +2

      @@shanew3595 Why is that barrel needed???
      The water level is at a higher level to the level where the water should be forwarded..
      So it is enough just to put the pipe ... with the long part towards the watering destination ...
      What does the barrel do?.. just start the system?

    • @shanew3595
      @shanew3595 2 года назад +12

      @@shhs1791 it does not have to be a barrel it could be anything. so if you know how siphoning works the what of the water falling creates a suction that will pull water up and over a barrier, however without a pump of some kind on a pipe or hose the output needs to be lower then the input otherwise you loose pressure and/or prime and other water goes the other way. so to counter this you need a brake to prevent backflow. the barrel has an inlet at the top and an outlet at the bottom with an air gap to prevent backflow. this allows you to move water up by allowing the weight of the water in the barrel to drain causing a vacuum to form in the barrel and this vacuum pulls new water into the barrel, thus continuing the process. is the amount of water leaving the barrel exceeds the volume entering then you negative pressure/vacuum become grater, and in this video that negative pressure or vacuum was grater then the barrel could withstand. to remedy/fix this you either need to decrease the output or increase the input.

    • @shanew3595
      @shanew3595 2 года назад +2

      @@shhs1791 one other thing the pressure of the out always needs to be greater than the input if the input is greater than the out then you will draw air in through the out and lose your prime or negative pressure or it will just simply not flow, as the inlet water weight exceeds the output.

    • @balwek2
      @balwek2 2 года назад +3

      @@shhs1791 If you understand How to measure the vacuum let me know... why the drum crushed, find out yourself. Let say the vacuum 0.4KG/Cm² to be lifted the water 4M above the water level.. what the outside surface of the drum, size maybe 95cm high diameter 60cm do your math x 0.4Kg. so how many Tonne???? Atmospheric pressure??
      It just transfer the water from higher level to lover level, is a siphon system.
      Need the drum, to have 1M clicks.... on this type of videos.
      Somebody prove it I'm wrong! Build one for yourself.. will it work?
      The water won't flow upwards. Only one way can be done with Ram pump, with a loss of water... To pump it higher level. but condition apply..

  • @alaminmuhd6642
    @alaminmuhd6642 Год назад +9

    Hmmm! You did well! And for the next time, you may try to equalize the pressure power of the suck-in (from the dam to the drum) and the push-out power (from the drum to the outlet) so that the output will be equal to the input. Or do not fill the drum with water 100%, at less make it 80% water and 20% air. Both scenarios may save the drum/plastic from squeezing, I guess. Thinks with me!

    • @nancywood4748
      @nancywood4748 Год назад

      is the output lower than the input?

    • @MuhammadFrazAslam
      @MuhammadFrazAslam 11 месяцев назад

      ​@@nancywood4748No, He is saying output elevation is lower.

    • @MuhammadFrazAslam
      @MuhammadFrazAslam 11 месяцев назад +1

      He just Use a metallic drum which already has a thin sheet. These drums are only made for atmosphere pressure or slightly high pressure but definitely not for extremely low pressure. If He could use Water Tank that has thick sheet of plastic likewise his pipes are then Deformation will never be happened. 😂😂😂

  • @howiej4084
    @howiej4084 10 месяцев назад

    Congratulations. You have discovered the joys of siphoning.

  • @momonsukirman2856
    @momonsukirman2856 Год назад

    That is a good motivation. Really ilike this video ithinks this video is infortan for farmer or gardener. Thanks.

  • @flavioaugustoribeiroevange5489

    兄さん、いいアイデアですね! 上向き300メートル(300M)、500メートル(500M)千メートル(1000メートル)上向きなど…! そして最高なのは、水中で水力発電機を使えること! 水力発電機! 4 つの出力で 80 ボルトの電圧 (80 ボルト) 120 ボルト (120 ボルト)、220 ボルト (220 ボルト)、380 ボルト (380 ボルト) のコヒーレント アンペアを意のままに!

  • @SuperAlraed
    @SuperAlraed Год назад

    حدث ذلك بسبب الارض منخفضة جداً والمسافة طويلة فحصل السحب بشكل قوي جداً وكذلك الفارق بالاقطار بين انبوب السحب انبوب التفريغ !
    كان ينبغي تكبير انبوب السحب قليلاً :
    تهانينا عملك ناجح جداً

  • @quyng3114
    @quyng3114 2 года назад +2

    Nhìn mức nước 2 bên ấy chỉ cần lung 1₫ường qua bờ nước sẽ tự động chảy ẦM ầm.o phải tốn nhiều công sức

  • @zobirish
    @zobirish 2 года назад +18

    Note that the greater the diameter and length of the water tube, the greater the draw from the barrel - good work

  • @fadilibya99
    @fadilibya99 2 года назад +3

    You are correct, but you need to balance the pressure👌

  • @machines_ltd01
    @machines_ltd01 2 года назад +10

    you don’t need this types accessories!
    just take a suction flexible pipe, and take it from river to other place...and make it syphon...

    • @Veluc1f3r
      @Veluc1f3r 2 года назад

      Ahaha my mind had pictured Khaby Lame right after I read your comment.. ))))

    • @tonysebastian2614
      @tonysebastian2614 2 года назад +2

      Syphon system with flexible pipe doesn't work because the river is much further down than the paddy field

    • @mikekelly5869
      @mikekelly5869 2 года назад +1

      @@tonysebastian2614 Those are the only circumstances in which a syphon WILL work. Of course you can use a flexible hose, just not a hose that needs pressure to inflate (eg flat fire hose)

    • @Dingsrud
      @Dingsrud 2 года назад +1

      @@tonysebastian2614 Exactly, if the output is lower than the input (river) this system will not work, drum or not! It is an overengineered syphon.

  • @diyathomevn
    @diyathomevn Год назад +1

    a new project, thank you for helping many people without losing electricity and still pumping water but scientists don't know, you have invalidated the laws of physics, your project must be granted a prize International prize, you make the water column higher than 2m, then run the generator, get free electricity and sell it to households for money, it won't take long to become a billionaire

  • @PeteThecurious100
    @PeteThecurious100 7 месяцев назад

    Great. You have proved the theory of making water travel uphill. All it needs is a thick steel cylinder.

  • @AmaduDabre
    @AmaduDabre 2 месяца назад +1

    Very good intresting ❤❤❤❤

  • @alexanderbrown1407
    @alexanderbrown1407 Год назад +1

    Just have to balance the outlet water to intake side .so say 2 lt in 2 lt out and no implosion to drum.good job and video.

  • @moradmoses3779
    @moradmoses3779 2 года назад +4

    Hahahahaha I was so piss off all the way till your drum🤣 , finally I started laughing as I sow your drum 😅🤣😂😅🤣you're funny. it is not the drum soft! but outside pressure is higher than inside pressure, that's why it caved in

  • @confused5573
    @confused5573 Год назад +1

    great experiment on water pressure! very good!

  • @dabestnapinoy
    @dabestnapinoy Год назад

    Ha! Ha! U are sooo real my friend... go! Go! I like u very much!!

  • @PhanOT11
    @PhanOT11 2 года назад +3

    Great invention, buddy.

  • @AzizurRehmanShaikhOracubesERP
    @AzizurRehmanShaikhOracubesERP 2 года назад +6

    This technique is begin used in our villiges for many years. we dont use centeral drum it is not needed. only you must have a long enough pipe. the source wather level must be higher than the target level. Only you have to do is to lay down the pipe from one end to other and suck water with your mouth until the water comes in your mouth. then leave it water will start comming without any effort. and it will continue until source water level is higher than destination water level.
    I will appericate if it continue to work when source water level is lower than destination level.

    • @Artiken1
      @Artiken1 2 года назад

      Instead of sucking the pipe with your mouth. I would submerge the hose in the river, filling the pipe with water. Then with a single valve or hand over the end, lift the pipe across the road to the field. Trying to prevent air from getting into the pipe. Then once set in the field, open the valve or remove the hand.
      You are correct. It will either stop working or the water will flow from the field to the river. :~)

  • @김국환-w6i
    @김국환-w6i 2 года назад +1

    땡큐 좋은 화면 잘 봤습니다 땡큐 감사합니다....

  • @RaMon-w3w
    @RaMon-w3w 2 месяца назад +2

    The drum was deformed meaning the pressure coming out from the drum is greater than pressure going into the drum so do recommend that the size of the intake pipe should be the same with the outlet pipe because the gravity plus the pressure coming out from the drum is greater than the force going into the drum that is the physical logic not that the drum is weak

  • @JosephBitek
    @JosephBitek 5 месяцев назад

    C'est genial.je vais essayer de le raliser

  • @sugengberkah
    @sugengberkah Год назад

    Keren banget mas idenyq

  • @TheChristopher042
    @TheChristopher042 2 года назад +2

    Should have turned the drum over. Big pipe on the top.little on the bottom. More water in and more pressure at the bottom. Nice job

  • @FsOppoA
    @FsOppoA 2 года назад

    Đây là bài học cho người thực hiện sau..nên.cho vành sung quanh chống móp.nước áp lực còn mạnh hơn nhiều chắy nhanh...

  • @abiliomarques9971
    @abiliomarques9971 Год назад +3

    Tá valendo o esforço, portanto você vai conseguir. 🙏

  • @brandondelacruz6399
    @brandondelacruz6399 2 года назад +2

    Really truly amazing

  • @bambanghermanto2871
    @bambanghermanto2871 Год назад +9

    the water that is sucked up is at a higher position than the drain pipe so there is no need for a drum, the water can already flow

  • @sskkmm0904
    @sskkmm0904 2 года назад

    عمل ممتاز جدا
    كان مفروض تجعل الانبوب الواسع لدخول الماء والانبوب الاصغر لخروج الماء .
    وكان لازم تعمل عوامة في نهاية انبوب دخول الماء لضمان بقاء فتحة الانبوب تحت سطح مستوى ماء البحيرة مباشرة حتى لا يمتص الطين والعالق ويحدث به انسداد
    تحياتي لك من..
    ...صنعاء اليمن.

  • @davidfernando89
    @davidfernando89 2 года назад +2

    I think it is true the tank is too soft to hold the vacuum created inside it, due to the output is too big compare to the input.
    To compromise, the output valve may be adjusted to reduce the vacuum inside the tank just enough to flow the water.

  • @maximorosariosilva9582
    @maximorosariosilva9582 Год назад

    muy buena se ve que funciona solo se tiene que hacer otro deposito de mas espesor de la plancha fenomenal me gustó

  • @Eisndudjd
    @Eisndudjd Год назад

    Hank you very much for your sharing

  • @concerncitizen8988
    @concerncitizen8988 2 года назад +12

    You should have a pressure gauge to check how much is your required air pressure and it should be stable for continuous flow without crumpling your pressure tank.

  • @ruijomlaljakhup2008
    @ruijomlaljakhup2008 2 года назад

    Encouraging, new Technology water pump

    • @mikekelly5869
      @mikekelly5869 2 года назад

      The technology has been used for 5000 years by humans and has existed in nature for millions of years. It's a syphon.

  • @flavioaugustoribeiroevange5489

    兄弟,這個主意不錯! 可以向上扔三百米(300 M),向上扔五百米(500M)千米(1000米)等等......! 最好的是能夠在水中使用水力發電機! 水力發電機! 四 (4) 輸出八十伏電壓(80 伏)一百二十(120 伏)、二百二十伏(220 伏)三百八十伏(380 伏)相干安培!

  • @dona6920
    @dona6920 2 года назад +10

    Hi Freeenergy Team. I really enjoy your thinking and truly your demonstration works. I may be wrong, but this may be why the drum collapsed. May be the water out of the drum is faster than the water into the drum due to pipe diameter differences. Try the video again reversing the pipes. let the bigger pipe bring in water to the drum and the smaller diameter pipe take water out of the drum. or you may let it be the way it is but open the valve that connect to the outlet pipe to let air pressure help to suck water up from the pond. For some reason your setup is air tide. I think this way it will work without destroying the drum. Let me know

    • @vickytok65
      @vickytok65 2 года назад

      Way to go @Dona! You said the keyword *"air pressure"*. Releasing a little bit of the air pressure from the drum might help.

    • @buzzzkill9183
      @buzzzkill9183 2 года назад +1

      nah. just get a stronger drum.

    • @ricardotormodomenech7108
      @ricardotormodomenech7108 2 года назад +1

      Como se puede apreciar en el video la salida del agua es mas baja quel nivel del rio ,por lo tanto esto es un sifon, no te hace falta el bidon el agua saldra por su propio peso.

    • @oranghingel3980
      @oranghingel3980 11 месяцев назад

      It's not about releasing the air pressure from the drum, but allowing some air into the drum into the vacuum inside the drum will sake that drum from squashing because the rate of discharge is higher than the rate of intake thus vacuum is created within the drum,unless there's some hole or cap for some air to fill the vacuum space, the drum will not squash in like this.
      The intake and discharge rate are not regulated.

  • @mashorif9721
    @mashorif9721 2 года назад +1

    I am completely this is project 15 year before. So I know this is real project.

    • @mikekelly5869
      @mikekelly5869 2 года назад

      This is a real syphon, they've been in use for more than 5000 years by humans and have occurred in nature for millions of years

  • @hernaleoalbeos6180
    @hernaleoalbeos6180 2 месяца назад

    I enjoy watching your video❤❤with due respect can I apply this technology to my little farm as a show window to my neighbouring farmers...thanks and more power!!!

  • @rueltonio1929
    @rueltonio1929 2 года назад +7

    Well I think the outlet at the end is the same however the addition of vertical column for air to increase pressure and the addition of another one due to a mistake increases the outflow causing vacuum. So when it stabilises the drum is already deformed.

    • @blessed1sj
      @blessed1sj Год назад

      The outlet at the end restricts the flow very little.

  • @AbdulMuhammad-sy9uu
    @AbdulMuhammad-sy9uu Год назад

    Excellent invention

  • @jayarambhatsampaje2302
    @jayarambhatsampaje2302 5 месяцев назад

    Thank you so much

  • @alfrowong7436
    @alfrowong7436 Год назад

    It look great don't have to use any motor
    Pump very good skills science for the water passing

  • @Top3rev
    @Top3rev Год назад

    truly i learn good job! thanks

  • @ManjulaMathew-wb3zn
    @ManjulaMathew-wb3zn 6 месяцев назад

    The basic principle is siphon. You created a great method to fill the pipe without air from river to the discharge. The obvious reason why the drum collapsed is because it outputs faster than the input creating a vacuum inside the drum. If you make the input and output pipes the same size longer output line and higher discharge height it will solve the problem. The same thing can happen if the input line get clogged so you have to avoid debris from entering.

    • @ManjulaMathew-wb3zn
      @ManjulaMathew-wb3zn 6 месяцев назад

      If you use a backwater valve on input below water line the tank may be totally eliminated. At the highest point you still need the same mechanism to fill water wth the valve. But only one vertical fill shaft of very large diameter reducer and valve. It will serve the purpose of the tank.
      Great work!!!

  • @jamescarllagasca7572
    @jamescarllagasca7572 2 года назад

    Thank you for your idea brother.vrrry nice. And i will try to do it. Just need a little adjustment fir the pipes. Inlet & outlet. Thank you.

  • @kusumsahu5533
    @kusumsahu5533 2 года назад

    Thank you very good idia.

  • @ed-jf3xh
    @ed-jf3xh 2 года назад +17

    Your field is lower than the canal. You don't need the drum, just pipe. Just make sure you outlet is lower than your inlet.

    • @raulmontenegro5858
      @raulmontenegro5858 2 года назад +1

      Where can I conract your office if need the pump.

    • @mikekelly5869
      @mikekelly5869 2 года назад +2

      @@raulmontenegro5858 It isn't a pump, it's a syphon. All you need is a hose. Add a filler pipe and valve if you're feeling energetic.

    • @janosboros3582
      @janosboros3582 Год назад

      @@raulmontenegro5858és

    • @LocNguyen-eo4mf
      @LocNguyen-eo4mf Год назад

      1SHRUEYRYRURYTDTRTTTRTEYEYEYRYRURUUF&$&%€%÷_2WY2Y27EUEYRYRYYRYRTEY8QQOQ0@@raulmontenegro5858

    • @muhamedsherif5465
      @muhamedsherif5465 Год назад

      U just said the truth
      Many believe this foolishness

  • @د.جهادالاسماعيل
    @د.جهادالاسماعيل 6 месяцев назад

    احسنت اتمنى لك. التوفيق

  • @dahlanhusen2359
    @dahlanhusen2359 8 месяцев назад +2

    Tank you your experion for us and seeyou. Nek time.

  • @ASHORSHEMAYA
    @ASHORSHEMAYA 2 года назад +3

    You did a good job 👍, I think what you just need is to make a hole in the upper side of the drum and seal that hole with a rubber material so that the pressure difference between the outside air and the pressure of the air inside the iron drum can be handled after it became vacuumed inside that barrel

  • @Mo_ha33
    @Mo_ha33 Год назад

    يجب ان يكون السحب اكبر من الدفع ولهذا السبب انطعج الخزان يجب تبديل الانابيب بل العكس وتنجح الطريقة او الابتكار وهذه فكرة رائعة ولاتكلف استهلاك على المزارع

  • @anduamlak3
    @anduamlak3 2 года назад

    you brother make the best video i realy like it

  • @chouyang2955
    @chouyang2955 2 года назад +2

    Good . But entering pressure is lesser than out going pressure that's what happened

  • @IoaneTaboia
    @IoaneTaboia 3 месяца назад

    I believe the outlet is greater than the supplier. causing great vacuum into the drum which is too much withstand. Thank you very much.

  • @hariprasadthatha9166
    @hariprasadthatha9166 2 года назад

    Dear bro's he used reducer outlet but not sufficient totally good job.

  • @chanelgebangporjo
    @chanelgebangporjo 2 года назад

    Ist the best info .big tanks.

  • @andrewmulligan1663
    @andrewmulligan1663 10 месяцев назад

    Ha ha new type off drum that is well done

  • @PLANetVALUATORS
    @PLANetVALUATORS Год назад

    Interesting!

  • @flavioaugustoribeiroevange5489

    Kuya, magandang ideya yan! Posibleng ihagis pataas ang tatlong daang metro (300 M) pataas, limang daang metro (500M) libong metro pataas (1000 metro) pataas atbp...! At ang pinakamagandang bagay ay ang makagamit ng hydraulic electric generator sa tubig! Ang hydraulic electric power generator! na may apat (4) na output na walumpung volts boltahe (80-Volts ) isang daan dalawampung (120-Volts), dalawang daan dalawampung volts (220-Volts) tatlong daan at walumpung volts (380-Volts) magkakaugnay na amperes sa kalooban!

  • @aakinsholesi6935
    @aakinsholesi6935 10 месяцев назад

    Kudos to you.
    But you can change the inlet pipe to a bigger size than the outlet.
    This will enable more water into the drum, holding the inside of the drum intact and releasing a lower quantity of water through the outlet pipe.

  • @khalidahmed9314
    @khalidahmed9314 Год назад

    very smart idea

  • @fr.jaimsonthomasthekkekkar3310

    It's syphon effect. Thanks dear 🙏

  • @reyvrexquestorreyes404
    @reyvrexquestorreyes404 2 года назад +17

    The effect on the drum is the reverse of the hydraulic jack. The water source is higher than the output pipe outlet. There is nsturally a tremendous negative pressure on the drum. Simple siphon here.

    • @kimnielsenthewordyvikingett159
      @kimnielsenthewordyvikingett159 2 года назад +1

      I don't think so. A simple siphon is the discharge is lower than the intake and gravity does its job. But if you'll look behind him the river looks to be a good 8' to 10' below the discharge. Take another look at the video sweetheart.

    • @JavierJrSuico
      @JavierJrSuico 2 года назад +1

      simple siphone principle applied here.

    • @JavierJrSuico
      @JavierJrSuico 2 года назад +1

      but the problem his pipes crossed the road.

    • @johnjasonaustria4957
      @johnjasonaustria4957 2 года назад +2

      You are just making things hard. The source of water is higher than the area wherein the water is to be supplied. Siphoning would do the job. No need for any drum, only the pvc is enough all you have to do place valves in the correct location and a filling tube for the initial fill up of the pvc. Once set up is completed 2 persons must simultaneously open up both end valves

    • @shoshodecapo2288
      @shoshodecapo2288 2 года назад

      He should have filled 70% of water into the drum but he filled it to the brim so when atmospheric pressures acted it didn't get a vacuum. So it was full force on the drum..that's why you should not fill it to the fullest

  • @abanglongjoe5070
    @abanglongjoe5070 6 месяцев назад

    Peojek yang Gagal..

  • @edgarramirezvallejo4404
    @edgarramirezvallejo4404 Год назад +5

    The water outlet Is by lower than the inlet, so the system is not pumping It Is Just a siphon.
    In a real pumping the outlet must be higher than the inlet

  • @stumpy31952
    @stumpy31952 2 года назад +1

    great work man! thank you for sharing

  • @ASHOKPATEL-fp1ps
    @ASHOKPATEL-fp1ps Год назад +1

    Drum is good and it’s not a fault of drum but You need to increase the size ( diameter ) of input line , keep it bigger size (diameter) then output line

  • @dhe2824
    @dhe2824 2 года назад +3

    الانبوب الطويل يجب ان لا يغلق من الاعلي حتي لا يحدث ضغط علي البرميل
    اقصد الانبوب العمودي الراكب علي خط الري لا تغلقه من الاعلي لان السحب بفعل الجاذبية في خط الري قوية وتشكل ضغط علي البرميل

    • @hassanaitabbou2478
      @hassanaitabbou2478 2 года назад

      لا اظن
      لان في هذه الحالة عوض ان يمتص البرميل الماء من البركة يفضل ان يمتص الهواء من القناة التي ذكرت
      اظن الحل هو القناة التي تخرج الماء يجب ان يكون قطرها يساوي او. اكبر بقليل من التي تسحب الماء
      تحية اخي

  • @flavioaugustoribeiroevange5489

    אח, זה רעיון מעולה! ניתן יהיה לזרוק למעלה שלוש מאות מטר (300 מ') למעלה, חמש מאות מטר (500 מ') אלף מטר למעלה (1000 מטר) למעלה וכו'...! והדבר הטוב ביותר הוא להיות מסוגל להשתמש בגנרטור חשמלי הידראולי במים! מחולל החשמל ההידראולי! עם ארבעה (4) יציאות מתח שמונים וולט (80 וולט) מאה עשרים (120 וולט), מאתיים עשרים וולט (220 וולט) שלוש מאות שמונים וולט (380 וולט) אמפר קוהרנטי כרצונך!

  • @ADPE...4
    @ADPE...4 10 месяцев назад

    Fantastic job❤

  • @rihtpy
    @rihtpy 2 года назад

    มาชมด้วย สุดยอดๆเลยครับ

  • @Rumigamer
    @Rumigamer Год назад

    Keren sekali

  • @bonifacioortaliza9998
    @bonifacioortaliza9998 Год назад

    Fantastic demonstration.

  • @tteariki330
    @tteariki330 Год назад

    Love the video ma man gr8 job.

  • @muallimlabayka6377
    @muallimlabayka6377 2 года назад

    Good works

  • @robikramsa3365
    @robikramsa3365 Год назад

    Love from assam

  • @PLANetVALUATORS
    @PLANetVALUATORS Год назад

    Interesting! Make the water infill through the bigger hole and the water outlet from the barrel be via the smaller hole of the barrel; or use more rigid barrel.