If you suspect this cable being unplugged is your issue, you can probably get away with just moving the power steering fluid reservoir out of the way and snaking your hand down and around the back of the intake manifold to plug it back in, I was able to do it, and it fixed my problem with minimal effort
My car is 2011 528i sounds like wants to start building compression, then loss of compression it sounds like? Please any information would be greatly appreciated!
Yoooooo! Thanks man. My BMW has this issue and then the transmission started acting weird. I thought maybe I got 2 issues at once and started to stress. I was already doing the repair on the Crankshaft position sensor one my own, in hopes it affected the transmission as well and then saw this and it cleared it up for me. Again, Thanks.
@@TheLifeOfMartin nice 👍 I’ll make sure to order this part my car started shifting weird only from 3-4 and I got the trans malfunction errror on the screen I turned off the car and turn it back on and it didn’t come back ok just shifts weird now ... so hopefully when I change this everything goes back to normal !
@@MrTwosick i should say, i got it into limp mode today, turned it off and on and worked again. Either a boost leak or something with boost solenoids. It acted similar to before I changed the crankshaft position sensor but only till i turned it off and on.
On my 2008 335i I have the following codes: U0100, P1891, and P052B twice. I can’t figure out what’s wrong or needs to be replace. Any help or advice would be greatly appreciated.
i had bmw e90 3201 N46 engine. Car cranks but not start . Scan and prompt camshaft sensor inlet. replaced the sensor but no start/ check signal voltage its 10V.may i know whats happen?
Hey I have a 2011 328i and so I am having random stalling and then car won’t start back up just cranks. Tried a few times then waited like 30 mins and then it suddenly starts up normal no hesitation and runs and drives. No check engine light and it has happened twice. Once with my wife and then with myself. What do you think this might be???? I scanned it and no codes pending.
Hi, my 2016 bmw m4 doesn’t start, the error code is 164020 intake camshaft sensor,electric;short circuit to b+. I have replaced the sensor but the problem is still there. Any idea what it can be? Thanks
Did you wipe the error code after you replaced the part? Have you replaced the fuel pump? Have you checked your starter relay fuse? Just a few things that might help
Hi guys.... where is the starter fuse located... I have a no crank no start issue... have removed the starter motor and had it checked... all good.... have replaced earthing cable from engine mount to body.... still no result... have no codes showing that anything is wrong... have checked cable from starter as I know it gets very hot down there... any help would be most appreciated... kind regards John
@lorenz grice hi Lorenz, I've changed the starter motor with no result, had the battery checked by auto electrician, said I'd be wasting money to replace it... after going through everything I went and bought a new battery... running perfect again... it looks like the IBS is very sensitive, and it shuts down the starter motor... The funny thing is the headlights worked perfectly when I had no crank.... which is usually a quick test... but battery fix the problem... hope that helps as I know how frustrating it is trying to get to the bottom of the problem.... regards John
I appreciate your videos, but the very loud engine reving sound is so painful that I've begun watching Nathan & BMW Doctor instead. The sound clip is insensitive to people with chronic migrain headache or anxiety disorders or PTSD.
My 335i sat for 3 days and out of no where I turn it on and now reverse or any gear doesn’t work, it just says it’s in nuetral for a few secs and then says transmission dct or tca not sure but something like that. I need help please😭😭
Counted 37 guys in this video but always 1 great resource 👊😄
Can I ship my bmw via UPS for you guys to fix🤣
If you suspect this cable being unplugged is your issue, you can probably get away with just moving the power steering fluid reservoir out of the way and snaking your hand down and around the back of the intake manifold to plug it back in, I was able to do it, and it fixed my problem with minimal effort
My car is 2011 528i sounds like wants to start building compression, then loss of compression it sounds like? Please any information would be greatly appreciated!
Yoooooo!
Thanks man. My BMW has this issue and then the transmission started acting weird. I thought maybe I got 2 issues at once and started to stress. I was already doing the repair on the Crankshaft position sensor one my own, in hopes it affected the transmission as well and then saw this and it cleared it up for me.
Again, Thanks.
Did it fix it
@@MrTwosick I'll get back to you when the part gets here. Autopart stores was 120. Online 19.
@@MrTwosick yes
@@TheLifeOfMartin nice 👍 I’ll make sure to order this part my car started shifting weird only from 3-4 and I got the trans malfunction errror on the screen I turned off the car and turn it back on and it didn’t come back ok just shifts weird now ... so hopefully when I change this everything goes back to normal !
@@MrTwosick i should say, i got it into limp mode today, turned it off and on and worked again. Either a boost leak or something with boost solenoids. It acted similar to before I changed the crankshaft position sensor but only till i turned it off and on.
On my 2008 335i I have the following codes: U0100, P1891, and P052B twice. I can’t figure out what’s wrong or needs to be replace. Any help or advice would be greatly appreciated.
Hi i have 325 6 cylindrar and engine light is on and the fel code is p12ba and i dont know waht to do ?
Thank you
Help me
i had bmw e90 3201 N46 engine. Car cranks but not start . Scan and prompt camshaft sensor inlet. replaced the sensor but no start/ check signal voltage its 10V.may i know whats happen?
hey bro is hyandai sonata 2008 good ?
Ye, it is very nice.
@@변별력 lmfao you lie
does it post to have oil on it
yes
Thank you so much. You always have great info
E93 starts fine runs fine but if turned off will not start until motor is cooled. Is this related to this issue?
Yes!
Hey I have a 2011 328i and so I am having random stalling and then car won’t start back up just cranks. Tried a few times then waited like 30 mins and then it suddenly starts up normal no hesitation and runs and drives. No check engine light and it has happened twice. Once with my wife and then with myself. What do you think this might be???? I scanned it and no codes pending.
Guys, do you guys have a bad cps guys? Guys, don't worry guys, I'll explain to you guys how to fix it guys. Like and subscribe guys.
I am getting code 2DCA can you please help answer why I have this code and what to fix . I can’t find any answer anywhere E90 320i N46 engine thanks
My 2007 bmw 328i coupe has a rpm of 200 and tr stuck in limp mode... bmw tech says that 4-5 is below spec. Will this possibly fix my issues?
Have u ever found the problem? I got p0300 code and a misfire in all cylinders, and is in limp mode and rpm jumps around 300-500
I have misfire on cylinder 3 that will not go away replaced everything coils and plugs and injectors and seal. Still there I’m so lost
Change fuel pressure sensor.
Hi, my 2016 bmw m4 doesn’t start, the error code is 164020 intake camshaft sensor,electric;short circuit to b+. I have replaced the sensor but the problem is still there. Any idea what it can be? Thanks
Did you wipe the error code after you replaced the part? Have you replaced the fuel pump? Have you checked your starter relay fuse? Just a few things that might help
Great video man!!
Hi guys.... where is the starter fuse located... I have a no crank no start issue... have removed the starter motor and had it checked... all good.... have replaced earthing cable from engine mount to body.... still no result... have no codes showing that anything is wrong... have checked cable from starter as I know it gets very hot down there... any help would be most appreciated... kind regards John
Im having the same issue rn, it cranks but wont spark, it happened after i changed my oil filter housing gaskets. How did you resolve your issue?
@lorenz grice hi Lorenz, I've changed the starter motor with no result, had the battery checked by auto electrician, said I'd be wasting money to replace it... after going through everything I went and bought a new battery... running perfect again... it looks like the IBS is very sensitive, and it shuts down the starter motor... The funny thing is the headlights worked perfectly when I had no crank.... which is usually a quick test... but
battery fix the problem... hope that helps as I know how frustrating it is trying to get to the bottom of the problem.... regards John
@@johnfanale8714 i ended up having to change my crankshaft position sensor
@lorenz grice glade, you found it
Should a bad crank sensor cause a n55 to die after running a little
Can. Also can be vanos solenoids
I appreciate your videos, but the very loud engine reving sound is so painful that I've begun watching Nathan & BMW Doctor instead.
The sound clip is insensitive to people with chronic migrain headache or anxiety disorders or PTSD.
Thanks
I just came here to see what a snesor was.
you don't have to remove intake.....
good
My 335i sat for 3 days and out of no where I turn it on and now reverse or any gear doesn’t work, it just says it’s in nuetral for a few secs and then says transmission dct or tca not sure but something like that. I need help please😭😭
Megatronoic sleeves need to be replaced in the transmission
Did you ever fix this issue??? I’m having the same exact problem with my 2010 528i :////
And now the car won’t even turn on lol
You don’t have to take the manifold off fyi
okay
Smart guys
Every video they have done is for a v6 and not the 4.4 v8. They are not the same motor and he needs to stop saying that
Lol say replace it guys don't be cheap .my cam and crankshaft sensor gone on me one time in my 09 320i.it could run but I don't risk drive it
Looks more like Camshaft sensor
they look identical. it’s given me headaches
Guys guys guys guy
You MUsT stop saying “guys”!!!!!! 🙏 please this is constructive criticism
Thanks car won't start cranks but doesn't start might be crank shaft sensor
Lol say replace it guys don't be cheap .my cam and crankshaft sensor gone on me one time in my 09 320i.it could run but I don't risk drive it