Hey is there a version of this ESC for 2s lipo 7.4 volts ? , I want to use it with a 8520 7.4 volt motor& is there a receiver for flysky that will work for me ? I only have flysky i6s transmitter
Hey buddy. This is something I'm looking for, for my school project. Did you buy the ESC or make it? If you made it, would you mind sending a photo of the circuit diagram please.
This receiver doesn't have a brushed motor driver on-board. However most receivers with connectors like this one these days do have either a brushed 2 or 5 amp controller on-board so you can jsut solder the motor wires to two pads under the board.
The receiver choice will depend on what servos you want to run. See the compatible ones on the receiver page listed below. I have put links to the products in the video below. You may also need wire and connectors. See those sections on my website if you need them. RX - www.micronwings.com/Products/DelTangRx35d/index.shtml ESC - www.micronwings.com/Products/ESCBrushedMicro1S5A/index.shtml Motor - www.micronwings.com/Products/MotorBrushed7mmx16mm2.7Ohm/index.shtml Prop - www.micronwings.com/Products/Prop65mmTriTurbofan/index.shtml Battery - any 1S 3.7V battery is okay - maybe 130mah
The ESC shown here is for a coreless motor. But this ESC is no longer available. This is a link to a popular 1S brushed ESC - micronwings.com/Products/ESCBrushedMicro1S4ABareBoard/index.shtml
The ESC is powered from 1S battery and then that power is delivered to the receiver. It's not really a BEC because if just passes whatever voltage the ESC gets straight on to the receiver.@@DIyRcrc
![Veeze - F.A.F (ft. Rylo Rodriguez) [Official Music Video]](http://i.ytimg.com/vi/7hlz2S2GmIY/mqdefault.jpg)
thank you for informative video.I just came to know about micron wing where usefull parts available for my project...thank alot
Wtf good speed.
what motor/esc is that and do you know how much lift the motor generates?
if i will install 2 or 4 coreless motor. what esc would i use and how much amps?
Can you please tell me how to build one
Hey is there a version of this ESC for 2s lipo 7.4 volts ? , I want to use it with a 8520 7.4 volt motor& is there a receiver for flysky that will work for me ? I only have flysky i6s transmitter
This ESC is for brushed motors - 2S
micronwings.com/Products/ESCBrushedMicro2S8AWired/index.shtml
its motor work if my receiver input in 4,8-7,4 and ESC is 5A 1S and I install 1S Lipo? thanks
Hey buddy. This is something I'm looking for, for my school project. Did you buy the ESC or make it? If you made it, would you mind sending a photo of the circuit diagram please.
The brushed ESC is available on our website.
www.micronwings.com/Products/ESCBrushedMicro1S5A/index.shtml
can you use 1 brushed esc for 2 or more motors - probably a dumb question but idk
yes you can. but the motor will turn with same speed. cannot be differential motor
Sorry about this begginer question but why can the motor br connected to the receiver direcly? Thanks
This receiver doesn't have a brushed motor driver on-board. However most receivers with connectors like this one these days do have either a brushed 2 or 5 amp controller on-board so you can jsut solder the motor wires to two pads under the board.
@@MicronWings that makes a lot of sense to me now. thanks for the explanation!!
does the reciver works with any rc remot toys..do u sell both esc and reciver..I need one..I live in kabol afghanistan..
This unit does not work with just any transmitter. You need a DSM2 compatible transmitter. See our website for a list of products. www.micronwings.com
can u post to afg..the compatible product..motor .prop.reciver and esc..what wil be the price..tnx alot
The receiver choice will depend on what servos you want to run. See the compatible ones on the receiver page listed below. I have put links to the products in the video below. You may also need wire and connectors. See those sections on my website if you need them.
RX - www.micronwings.com/Products/DelTangRx35d/index.shtml
ESC - www.micronwings.com/Products/ESCBrushedMicro1S5A/index.shtml
Motor - www.micronwings.com/Products/MotorBrushed7mmx16mm2.7Ohm/index.shtml
Prop - www.micronwings.com/Products/Prop65mmTriTurbofan/index.shtml
Battery - any 1S 3.7V battery is okay - maybe 130mah
what esc is use for coreless motor?
The ESC shown here is for a coreless motor. But this ESC is no longer available. This is a link to a popular 1S brushed ESC - micronwings.com/Products/ESCBrushedMicro1S4ABareBoard/index.shtml
Only for DSM2 compatible transmitters?
all transmitter can be use
what is the voltage of battery
The battery is 1S - 3.7 volts
Are these reversible?
These units are no longer in producttion but they were one way only.
@@MicronWings Ah thanks! May try to harvest the board from a servo for reversibility.
Esc motor betafpv 0703 19000kv ????
Thank you
No this is just a standard 7mm brushed motor.
@@MicronWings oh, thank you. so can you help me to start a betafpv 0703 engine
@@dondoc00 Sorry I don't have any experiency with that system
@@dondoc00 You need a brushless esc, normally for those motors the esc are in 4 in 1, for that motor i'll recommend you a 6 to 7 amps esc
This esc does have bec
no it doesn't
@@MicronWings thats mean you use RX battery
The ESC is powered from 1S battery and then that power is delivered to the receiver. It's not really a BEC because if just passes whatever voltage the ESC gets straight on to the receiver.@@DIyRcrc
lol