How to replace rear ABS sensor | Peugeot 308,3008,408,5008 | Complete guide
HTML-код
- Опубликовано: 12 сен 2024
- www.youtube.co...
Procedure to replace rear wheel speed sensor for vehicle Peugeot modal 308,3008,408,5008 with complete guide sensor |
A wheel speed sensor is used by the anti-lock brakes to determine if a wheel is moving at a different speed than the others in order to control the anti-lock brake or traction control functions. Some makes and models use a single sensor on a single wheel for the speed signal. Some vehicles that have anti-lock brakes use the wheel speed and the transmission output to determine any faults. Most models that do not have anti-lock brakes use the transmission output for the speed signal.
If the wheel speed sensor has broken, there will usually be dashboard lights for the ABS or traction control systems illuminated. The ABS system will likely not function properly.
Step 1: Prepare your work area. Make sure the vehicle is on a level, safe surface, and you have set the parking brake.
Step 2: Loosen the lug nuts. Use a ½ inch drive breaker bar and a lug nut socket set to loosen all the lug nuts before you jack the vehicle up in the air.
Step 3: Jack the vehicle up and use jack stands. Jack the vehicle up and put it on jack stands. Place the wheels off to the side, away from the work area.
Be sure to jack the vehicle up in the correct location; usually on the sides underneath there are pinch welds you can use to jack from. Then make sure you place the stands on the body or frame and lower it down onto the stands.
Step 4: Remove the old wheel speed sensor. In some cases, you may have to remove the brake pads and rotors in order to get a clear view of the wheel speed sensor. Once it is visible, you can remove the bolt that holds the sensor onto the hub/knuckle.
Next, remove any clips or hold downs that are securing the sensor wiring to the vehicle's chassis/body. Once you have done that, unplug it so you can remove it completely from the vehicle. Use some emery cloth or sandpaper to clean off any rust in the areas where the new sensor will be going to ensure it fits easily.
Step 5: Install the wheel speed sensor and brake parts. Work in the reverse order of the way you removed everything. Start by plugging in the new connector and then routing the harness back so it is secured to the body/chassis. Then insert it into the hub/knuckle.
If you needed to remove the brakes, reinstall the rotor and brake caliper bracket along with your brake pads, and make sure you torque everything to factory specs.
Step 6: Reinstall the wheels. Place the wheels back onto the hubs using the lug nuts. Snug them all down with a ratchet and socket.
Step 7: Jack the vehicle back off the jack stands. Place the jack in the correct spot under the vehicle and jack the car up until you can remove the jack stands. Then you can lower the vehicle back onto the ground.
Step 8: Torque the wheels. Most cars use a torque from 80 ft lbs to 100 ft lbs. SUVs and trucks usually use anywhere from 90 ft lbs to 120 ft lbs. Use a ½ inch torque wrench and torque the lug nuts to the proper specification.
Step 9: Test drive the vehicle. After the wheel speed sensor is replaced, the ABS and traction control lights should go out. In the event that they don't, you will need to take it to a certified mechanic to have them reset the vehicle's computer.
To test drive, go down a safe road where you can speed up and hit your brakes hard to try and engage your ABS and make sure it is working properly.
How or replace ABS sensor | How to replace car wheel speed sensor | How to change abs sensor| How clear abs fault| Procedure to replace abs sensor | How to replace Peugeot 308 abs sensor | How to replace Peugeot rear abs sensor | How to replace Peugeot 3008 rear abs sensor | Rear abs sensor
I did this job yesterday. A few things to note. Clean as much as possible before you remove anything. Take photos. Get the car as high as you safely can. Get a rubber mallet to hit the wheel with. It'll probably be fused to the hub - mine was. Get one of those screwdriver-handled telescopic magnets, to retrieve the hex bolt when it drops into the hub back-plate. Mine did. Have the right length hex key - the longer, the better. Have a good torch.
Have a can of WD 40 to hand. Once removed, clean the location for the hex bolt. The spring clip attached to the old sensor was so rusted in place, it stayed buried in the crud, and made it impossible to locate the new one. Don't forget to re-tighten the wheels once the load is back on the car.
I only attempted this to save money. It took me a couple of hours, and the sensor was £16.99 from a well known online auction site. The only downside is, I used muscles I'd not used in years, and now I can't move! 😂
Thanks for the tips on removing screw at 1:18 . What I did was remove the wheel hub just to replace the abs sensor. Now I know there's a smarter way to do it. Thanks again.
Oh my goodness. A big thanks. On first look I thought I had a lot more take off to access the Allen Key. Thanks for sharing.
Great video, going to do exact same repair when part arrives on Saturday, wish me luck.
Good luck bro👍
Hi bro, how can i contact you?
Well pictured video. Easy to follow step by step.
Excellent, I will try clean mine first before teplacing.
Nice video...step by step.👍👍
Thanks
Thanks man , when i see where is i was scary to start... :)
Perfect video !! Thanks
Good job
Thanks bro
in this car the wheel speed sensor is also The ABS sensor that you replaced? thanks
Nice workkkkk
Nice Step by Step Tutorial Video, may i know is the steps similar with front ABS sensor. May have to do it myself later. Thanks!
Is that 2008 the same way to do it? Thanks a lot.
Thank you, I have a handbrake faulty which also throws up abs and esr on the dashboard. I’m thinking of going down this route.
If like that you should change handbrake switch so other faulty sign will disappear
I changed the sensor as per instructions in video. Once sensor is removed, I recommend cleaning the backplate as rust pushes the sensor out of line and into the hub. Follow the video, takes 15 minutes.
@@stevegerrard0 did that fix the problem you had? Having the same issue and it’s still there after replacing the handbrake switch
Baie Goed..Baie nuttig
Question does the same method apply to the 308 sw on a 16plate, also does rear abs speed sensor if i got a new one come with loom..
Does the abs sensor screw into the stub axle then?
Hocam merhaba. Aracım 2 gün karda kaldı. Bugün çıkardım hareket halinde iken hız sabitleyici arızası işareti ve motor arıza ışığı işareti çıktı. Sağ arka teker de gittikçe hızlanan alarm sesi gibi gibi bir ses var.. Arka lastik çok kara gömülmüştü. Acaba abs hız sensörü ne karmı girdi. Akü kutup başını çıkarıp takıyorum resetliyorum. Sonra sorun tekrar ediyor. Başınıza hiç geldimi.cevap için çok teşekkür ederim.
Can u please tell where is the rear speed sensor in peugeot 207 2008?
You can see at rear wheel hub behind
Will the faulty wheel speed sensor affect your fuel consumption
No
How many abs sensor does a Peugeot 308 have? Can you replace the abs sensor without a car lift or jack stands? Just with the own car jack. How do you know which abs sensor is faulty?
This car have 4 wheel speed sensor. Yes you can use own jack to lift the car so easy to fix the sensor. Use diagnostic tools to fine out the faulty sensor.
@@rajsilverautolearn Thank you very much for your prompt response. I don't get any fault related to the ABS system with an OBDII reader. I just get a message on the car screen saying Faulty ABS braking system and the ABS light on. Could it also be a defective brake pedal switch?
@@csraln6748 can you tell me what fault code is that?
@@rajsilverautolearn Not a single fault code on Car Scanner app. I guess I need an official diagnostics tool like Peugeot Planet or similar. I just get that warning message on the built-in screen of the car and the ABS light on of the instrument panel.
Yes you are right,you should use official diagnostic tool
Is it a the same steps for the front sensor too?
No its different steps
P0087 Vehicle speed (CAN) given by ABS no signal.
When I travel about 50 km (al4 gearbox), my gears change at 4200 rpm and do not go into manual.
Peugeot 307 2005 1.6 engine
It was diesel car or petrol
code that indicates a fault within the fuel delivery system. ... Low fuel pressure causes the Check Engine Light to trigger by the ECM and a failsafe mode is enacted to prevent damage until repaired.So try to change fuel filter
@@rajsilverautolearn petrol
@@rajsilverautolearn my vehicle is gasoline. When I connect to the original device, I do not get any error other than ABS error. I think the vehicle is reading speed from abs sensors. Can abs ecu be broken?
Nice video...step by step.👍👍