10 Minute Doggy Door Install
HTML-код
- Опубликовано: 19 ноя 2018
- Worlds Largest doghouse gets a self closing dog door. In this video I put the door in for the shop boss finally so he can quit leaving the big walk thru door open when he let's himself in. Sawing, cutting, screwing and drilling gets the job done. Tools used, Circular saw, sawzall, drill, and phillips screwdriver, and the Jimmy Diresta "if it looks straight it is straight" eyeball level. The boss doesn't seem thrilled with it but he is using it. I think he would prefer his minion tend to his door needs but when not available he can suffer with this. lol Thanks for Watching!
Наука
The only doggie door that's within 1 1/2 thou.
Bailey will like that for sure👍. Light press fit👌
It makes the flap seal better too. :-) He used it some without coaxing today.
Nice job! I liked how you left the camera run so we could see how the whole job was done. Keep them coming!
Installing a hole without calipers, dial gauge and a hand held slitting saw, Very impressive... 😁
The boss won't complain when it gets colder, he'll be happy he can get in quick ! But now you have to deal with surprise inspections...stay on your toes !
What????
Huh? What the fuck you smoking??
My man is a beast with the circular saw. That's something that can only be learned through trial and error. Lots of experience.
Nice work Bubba... you're good with that Saw!
Ha ha love it , you can tell he's like "what I can just go in and out like whenever" he just so wants to build stuff for himself that's why he made that bed in the insulation. he see's you in there building stuff and it looks like fun
Yes normally he just twists the knob with his mouth and in he flies! Problem is he doesn't close it back!!!
Quick & easy ! Good job Brian. I'm sure Bailey will appreciate it !
Have a Happy Thanksgiving !
Heck, the supervisor might even give you a xmas bonus for this work
I'll bet he throws Brian a bone! 😁
Did Bailey check the interference fit with his Starett micrometer?
The
E
Looks good sir. I was going to complain about the screws being on the outside, since that wouldn't be "secure" but realized you are putting a giant hole in the door.
Bailey approves,you’re within tolerance and done before deadline lol
learning a dog to use the door ,a very smart Bailey learns fast ,that's why he is "shop boss"
Great, informative video, thank you!
Bailey says hey no sweat! I’m a smart Doggy.... Bark Bark... 👍🏼👍🏼👍🏼✌🏼
I had this vision of a door clamped to an angle plate on the HBM...LOL
Gotta use the appropriate tools for the job sometimes. lol
It's a deluxe accommodation for the boss. Cool!
Ya darn right , good Job man .. ! When He want to find his couch , He sure can ..
Nicely done.
Aww, I thought you were going to do it on the mill!
Haha me too. lol
It would have been more interesting
I think that might be the smallest power tools I have ever seen you use! ;-) Nice job.
Thanks
Hey, inspecter finally has his own access. Bailey's like, "the sensor on this door isn't working i gotta use my nose." 😀
that is the problem!! lol I should have known he would expect an automated version after all he has been watching those NYCCNC videos. :-)
Cool Beans Glad he's giving it a try.
Nice. Thanks for the video.
I just built a new place and we put a doggy door in it. Our two dachshunds were like Bailey at first, not trusting it too well, but now they fly through it like it wasn't even a speed bump. Among the critters here in Texas are lots of skunks, so that panel is important.
4:45-- I used the same detail saw doing the moldings in my house..
That napk8n in the deadbolt is working sooooo hard lol
Keeps the wind out!
Great job Brian the boss is happy and he said you deserve a pto day but he didn't say when you could use it lol
He has got his own place now. All he needs now is a girlfrin. Go Bailey ! Thanks Brian.
nice fit. supervisor approved ,,,
I’ve never cut a metal door with a circular saw and not had metallic shards hit me in the face. That’s why I would use a zig saw.
You must have had a DRO on the circular saw to get that fit. 👌🇨🇦
I was a bit surprised that you didn't mount the door on some machine and indicate it before cutting the door.
My niece has a door for her pup what locks except when the dongle on the pup's collar is near. He just pops through, but other critters can't get it unlocked. I guess he could invite his posse if he stood near the door though.
Hey Bluegrass
Good video,
Ur shop build has been one of the most EPIC projects I’ve seen on RUclips
Better not make a video of catch’n bass in ur ponds coz people would get COMPLETELY jealous
Good job!
Nice Job Baily approved!
"Looks like a machinist did it," and without using an inside micrometer to check the cut. :D
Bailey is a fast learner and of course you already knew that.
6:04 its got that toolmakers fit
You could hear the precision fit pop. lol
Always listen to the boss 🤣
Supervisor would like to have a bing bong doorbell to announce his arrival
“Measure with a micrometer. Mark with chalk. Cut with a chainsaw.”
Not a problem for a good chainsaw operator. :-)
Supervisor 100% approved!
I real dog lover. I am sure he now knows it’s home.
A dog for all seasons!
Put a double cylinder deadbolt on it so the hoodlums can't crawl through and unlock from the inside.
More like Smith and Wesson bolt action dead bolt.
@@barrygerbracht5077 He goes to work. He can't be standing there around the clock waiting to shoot everyone.
Baily is there 24-7 to bite everyone though.
@@bcbloc02 Brian, he looks like a lover not a biter.
You must not remember the recent mailman incident with the doggy door delivery when he ran them off.
I need one of those for when I'm drinking.
😂💀
That job is Bailey approved.Later and all the best.
Photo bombed by a beetle 😜
It looks easy to install.
Judging by my dog, Bailey will soon be hitting that door full speed. FREEDOM!.
Baily has always been free to roam so he doesn't get to amped about it.
The sniffer-visor approved.
Brian, I see you using the cordless Milwaukee Sawsall. if you’ve ever used a corded one, how would you rate the cordless? I bought the first lithium powered Sawsall that Milwaukee put out and it was miserably underpowered and toasted the batteries in just a few months, it has been sitting there on the shelf ever since. I went back to a corded one.
Not near the power of my Super Sawzall but it does very well. It does suck hard on the batteries though. I can run almost 6hr use on my impact but the same battery in my sawzall probably won't make 20minutes of fulltime cutting.
I have the Makita version and it's OK, but you can only pull about 500W safely out of those batteries. The brushless motor makes up for some of the difference but it's still not the same as a corded one and you can tell. They make a version with two batteries, if you need more power, but also heavier.
Depends on the job but most times I prefer the cordless version of a tool now, power isn't everything
The critter cover is important. Wouldn't want the local raccoons and possums and such following the Boss into the house.
I find the hardest part is drilling the holes perpendicular to the door without a jig to align my drill.
great winter time upgrade....when Howie moved in he ran through the screen door in our bedroom and the bottom became loose, that is his summer time doggie door...two other screen doors and he know that those are not for his access....hmmm....new series...”this old dog house”....lol
So Howie made his own doggy door! lol
Woof!
precision is just built in to you. isn't it?
. . . hope the boss likes his new door.
He uses it multiple times a day. I think he appreciates the warmer shop anyways.
Ok , just a heads up; remove the door, lay it flat on saw horses , Mark the door, use a 4” grinder with a cut off wheel ( not a grinder wheel ) or reciprocating saw , cut opening , easier to cut, easier to assemble! Use 3m waterproofing tape under outside frame. Shalom!
Glad to see you have your priorities straight!
ATB, Robin
That is what Baily said too! :-)
Will this work on a fiberglass door as well? 🙈
I don't know why not but be sure to wear a repirator as the saw could blow the glass fibers in the air and you don't want to breathe those.
I expected a boring mill project on the door. 😂
You have admire a shop boss who has the love and admiration of his minion. This was done off hours so as to not impact production billing right?
Make sure the tax assessor understands that is a large dog house.
_Dan_
Baily has gone uptown.
Just means the boss can creep up on the minions to make sure their working hard
You could have taken the door off the hinges and laid it down on some sawhorses, but you did all right.
Extra work.
Work smarter not harder 👍
Now raccoons and skunks can visit. And children will love it. Our gran daughter climbs thru our little dog door , great for company . Need a backer so no goods don't get in when your not there.
Did you watch the video?
I have often wondered with doggie doors how you keep human intruders out?
You can't keep human intruders out if they want in. Like a house they just break the glass and go thru the window, no real effort required. The dog on the other side of the door ready to chew your face off for getting on his bed is a good deterrent.
Nice job but generally the screws will get installed so the heads are on the inside of the house. Doesn't matter much here since the hole is so darned big
I could get in there myself.
Well the 120lb cane corso barely fits thru it now.
takes way longer for cats to figure those out.
Where are you located
Very good just job he will be able to nip in and out when he likes.Hope Bailey said thanks 🙏 boss
Was that a fiberglass door you cut into?
Yes, I believe it is a fiberglass cover with a foam core.
Does anyone know the link for the actual doggie door he was installing??? or where you can buy that frame/kit????
It is a pet safe door I bought on sale at feeders supply they also have them on amazon. www.amazon.com/PetSafe-Efficient-Extreme-Weather-Aluminum/dp/B082N4RBZN/ref=sr_1_5?crid=1HQWJ81D9ZDSD&keywords=pet%2Bsafe%2Bextra%2Blarge%2Bdog%2Bdoor&qid=1683117519&s=pet-supplies&sprefix=pet%2Bsafe%2Bextra%2Blarge%2Bdog%2Bdoor%2Cpets%2C112&sr=1-5&th=1
Looks a little different now but believe it is just updated I know when I got mine it was on sale for like $90 glad I got it before inflation!
@@bcbloc02 thanks for the info but God damn that's expensive I found them for like 30 to $50
woof woof lol
With skills like that you're going to get moved up to head fry cook and chief bottle washer before long!!
Fully inspected and approved. Now we need to come up with a placard to put on top of the door.
Machinists make good carpenters but not the other way around.
Finally...!!!! ( Says Baily...)
Did you check if you need to start dieting in order to use the doggy door in case of an emergency...??? lol
Guess it's not that burglar proof, at least the slim ones...
Never heard about those circular saws that can make square corners... ;)
It is all about the skills. :-)
Yeah but what if you also ha e a screen door.
You eve could of use the big drill with a mill in it too.
Hope Baily lets you stay in his house.
He likes having me around, he can't pet himself. lol
big bug on door frame
Well done... now you can take a shower 🤣🤣🤣🤣🤣🤣🤣
"I got dis cover for duh duur hurr to keep critters out, so i got dat too."
I had a client with a doggy door have a possum enter her garage while she was on vacation. Apparently the dogs were to terrified to do anything. It ate all the dogs food and shit every where leaving a disgusting mess. People don’t realize what could come in their homes through those things. Don’t think a dog will always fight off a wild animal.
Guess that is why they have the fancy collar activated doors now.
@@bcbloc02 Wow no kidding? Yeah that would be a great idea. Not to mention the doggy door this woman wants me to install I could crawl through. If a criminal really wants in your home there are ways to neutralize dogs.
wood door or Steel door ?
That one was wood but you could do a steel door the same way with the appropriate blades.
Really? U had to ask that after u watched saw dust fly everhwhere in half the video. Smh 😂
C.E.D. entrance. Chef Executive Dog entrance NO varmints allowed vaulters will be perused
Doggy/burglar door
With a circular saw? Why not use a jigsaw?
KMF Because i am not good at plunge cutting with a jigsaw.
@@bcbloc02 you don't have to be. Just drill holes in each of the four corners.
do you worry that kids etc. might get in and cause mischief?
Kids get shot around here. Also there is a 85lb pitbull to welcome them where they don't belong. :-)
A lot easier if you took 5 minutes and took the door off.
Nice job but not that helpful/ instructive. Like, what kind of blade did you use in the skill saw and the sawzall? One can't just pick up a skill saw and use the same blade you would cut a 2x4 with. And I know you have on glasses but would have been good to warn to use safety glasses. I know, I know, that is just common sense but lots of people on here searching these videos to learn how to "do it yourself" and save some money don't necessarily have common sense. Again... nice job.
The trouble with that is it's big enough for most burglars. You can get locks activated by a proximity transmitter on his collar, but if you added a motor to the door he'd get the full service feeling.
There is a 85lb pitbull to welcome them where they don't belong. :-)
The Only Pain In The Ass Feature Is Remembering To Install The Security Door ,There's Gotta Be A Better Way !!!!!!!!!!!!!
What about the thief??
The dog takes care of them.
@@bcbloc02 😂😂😂
DO NOT use an angle grinder on a metal exterior door. There is insulation inside that burns from the blade and the smell is ACRID. I will never do that again. Maybe use an air hammer with a chisel bit. Anything but an angle grinder. Worst smell ever
A thief can crawl through that big hole, meet up with your dog, thiief crawl back out! Thiet said: just waste my .......butt to the dog
Your no machinist, a true machinist would have found any reason to Use the Big Mill? ;')
Adam would have used his Shaper!
Keith would have used his CNC table!
This old Tony would have hit it with a Square Hammer!
And The Chieftain would have used a Abrams!
Then you wimp out and use a Saw, not impressed!
;')
Like your work, keep it up.
Probably why those channels are all WAY bigger than mine! lol
@@bcbloc02 - Slow and steady!
Just PLEASE don't become a BANGOOD, A Lady of the Night!
I am not real big on hocking cheap low grade goods.
Hopefully, the house is not located in a crime ridden neighborhood. But then maybe with the size of that dog, it wouldn't matter.
My 85lb Pit Lab mix has to eat. :-)
Can't believe you didnot take the door off hinges set it up in the boring mill and cut out the opening to 1000th use the mew new repair DRO just use a roughing end mill Realy would of been a funny video....
Probably so! Sadly I don't have that kind of time, I have too many other projects to do to be screwing around.
@@bcbloc02 yes I know your ahard worker, was just kidding for the humor. Hey OX tool or Old Tony would of whent for the humor, they must have a lot of time, it is okay I much enjoy your work. Give Boss Baily a pet for me, what kinds of treats do you let him have??? Maybe send something you aprove of.