My a 72's touch screen became unresponsive a day ago, and now I can t even access settings. I've tried everything short of factory reset and disassembly, so I'm hoping maybe you might have some ideas on a solution? Great video by the way, love the detailed instructions. Might try this if nothing else works.
Same, but I think it might be the new update or the flex cable ( 1:27 ), but I'm not sure yet, I'm gonna buy a flex cable and fix my phone, and MAYBE come back and tell you guys. Maybe.
Hello, I think my Samsung A72 has an issue with regards the backplate, it fell off and I'm guessing that Samsung has a poor glue residue. No history of repair though, what will I do? Thanks.
you can replace the adhesive with a new one. Here is a link for it: www.ebay.com/itm/234722749721?hash=item36a690ed19:g:v~MAAOSw5p1jPbYF&amdata=enc%3AAQAIAAAA4J74u5kvH8apIL1oMsB3gi%2Fe0J0H1ZH2zwsOszCqzcx12UXa%2Bq4sXROJgWNDUbySn3qU4spJfdqmBfk7%2F4X5sTM9BWdQeUbq60n9WTpWb070Nb9ucYzvNSt2XPxamT3u0dnx2FtUGVr9Pkvqoc9E9XLGAvLM4KMv14vtTtIvhMvkOFIBkZ3ArbdJ2mcDUSgvdmlDZpxaveFqk6IMlJwX3mAksu4qq%2FAu5saodXOs9C2h%2B3qU3tyz36sjC2QP67zN1O7mzh9f4ppNva4nRSz6WvGnKxLeteiqjaBUQMYR0Mnd%7Ctkp%3ABk9SR6TM3OrOYg
Great quality video and details that I haven't seen on other disassembly ones. Thanks. I have a question, there are two pinholes on the top, one for the SIM/SD card slot. The other seems to be a microphone. What happens if you use the sim ejector on the mike hole. I would imagine Samsung Engineering would have accounted for that chance. Did they? Asking for a friend....
Thanks for the great video! Could you tell me please what parts do I need to replace if my fingerprint sensor doesn't work? Will it work if I replace the sensor and the bottom board or I need the sensor only? Thank you!
Hi, I have a question: My A72 stopped vibrating out of nowhere and sometimes the virbation returns whilest i'm tyling even though its a lot weaker. I also hear a rattling noise, but this is the camera assembly you said. Is this fixable without dissasembling the phone? Thank you!
Hi, yea you can heat it up with a hair dryer and pry it off. Make sure all the liquid inside the phone is dry and that there is no corrosion around any connectors or chips so it doesn't short later and damage your device. Then you can re apply your current back with new adhesive strip like this one: www.ebay.com/itm/155008250046?hash=item24173630be:g:RFMAAOSwAdlhBEq1 or you can get a new back cover that already has the adhesive pre installed, so all you do is peel off the film and apply it to your phone like this one: www.ebay.com/itm/115130401775?hash=item1ace4e83ef:g:hFQAAOSwdfdhreqb
Hello, my phone was soaked in a laundry water. Unfortunately, the back part was open (it was opened by a technician and didn't glue it properly)... Then there was a water inside (since it was open)... Is there a possibility that it will be repaire? Or should I buy a new one?
Most likely will be too badly damaged. The only way to tell is to open it up, disconnect the battery, dry it out completely, brush off any corrosion over the chips and connectors with a small brush and then test the phone to see if it will work. If not, you would then need to order working parts like the screen, battery, etc. to test and see which is not working or has gone bad.
Hi! I dropped my samsung a72 in a water last week. At first i was not worried since its a waterproof phone but after letting it dry, i noticed that there is still a moisture visible inside the back cover of the phone. I literally panicked since the phone is just 9 months. Can there be any damages inside my phone? Btw, the phone is working fine and there seems to be no damage on its functions. Thank you!
i dropped mine in the washing machine but thankfully i got it out before it ran a full cycle.. did your phone not turn on too after you got it out of the water? what did you do to dry it out?
@PBKreviews On my A72, when i press the center of the back cover, I hear a plastic click. Then it should be the plastic that contains the graphite pad that probably has some play. Do you agree?
Yes correct. There is a slight space in between the back plate/battery door in some portions so that would be the reason you are able to press down and hear that.
@@PBKreviews Thanks! No need to worry then. Although these clicks shouldn't be expected in a Samsung phone imho. Nevertheless even some iPhone Max models have that, apparently...
I am noticing a bump/hump/ swell to the right side of the camera unit is it normal or something serious ? There is a slight battery draining issue and a slight heating issue near the camera unit when browsing.
My samsung a72 back cover fell off on its own. Thats why I was curious on how to glue the back cover without affecting the water resistance capability of the phone. But it looks like you didn't even glue it back? Is gluing it back enough? Or it has something more that is needed?
I don't show applying a new one in the video, but here is a link to the replacement adhesive needed to re apply the back. www.ebay.com/itm/234722749721?hash=item36a690ed19:g:v~MAAOSw5p1jPbYF&amdata=enc%3AAQAIAAAA4J74u5kvH8apIL1oMsB3gi%2Fe0J0H1ZH2zwsOszCqzcx12UXa%2Bq4sXROJgWNDUbySn3qU4spJfdqmBfk7%2F4X5sTM9BWdQeUbq60n9WTpWb070Nb9ucYzvNSt2XPxamT3u0aDNNFYR4jt6wZ1Zzfn6Erb1hFkLqaPOacoktKdunddqWkC%2FZlfBNE1Jy4ws0i37Z7odIT7TvxLcjPCtOAOBk%2Fd7A1gofxCCa%2F9Gxh%2B0%2BIRPXWqHK0PbdQU5QzpmQq74gQbtKr1MEvXl7Ysad0My4Zg62mkXiV%2FGaoe%2B%2BIJ3Pe6t%7Ctkp%3ABk9SR8rLgO3OYg
Hello, my Samsung A72 can't recognize the SIM, from what I've understood, I should replace the main flex cable and/or the sub-board. Is it correct? Thanks a lot.
Hi, no the sim reader is located on the main board and not the sub board. So would require a specialty shop that does soldering to be able to replace the sim reader on the main board.
Sad to see the mid frame cannot be replaced.. if you want your phone to look new in the long run, and you like to carry your phone around without a case, that's better off buying a new screen. But still, at least its got IP rating in exchange
Hi, nothing will happen, its just there to help transfer some heat but its not a necessity for the speaker to function. Will work without it just fine.
Nice video bro 👍🏻. I just recently dropped my phone and the screen goes all black. No damage on the body since I used case. One thing I noticed is the screen actually works even it's all black (it vibrates when I touch where the fingerprint scanner located). So then I tried to remove the back cover and suddenly the screen turned on and I can use it like nothing happened. But the probrem is when I put the back cover back on, the screen goes all black again. What could be the problem?
Hi, hmm that's odd. Might be a short or something. Try taking apart the phone and making sure all cables are attached and have not become disconnected. Also make sure everything is seated properly and see if that helps. If not, might be a defective screen.
Hi sir, my main board is damage due to I dropped my Cellphone (A72) to the saltwater and it's already black screen and i cant charge also..is there a chance that I can retrieve my files and photos? please feedback :(
Hi, my A72 suddenly started to restart itself and only stops when the battery is drained, cannot start it and tried everything. Any clues on what to do next?
Could be many things. You would have to try a different battery to see if the battery has gone bad, or might be software issues, bad board, water damage etc.
Ya, its soldered onto the board so it would require a place that is good at soldering and that can find the part to be able to replace it. Wouldn't be easy.
@@PBKreviews thankyou for explaining.. instead to repair.. i would like to find alternative way that more cheaper.. maybe use velco and glue it on my cover phone.. then use led lightning that i can buy from china and attach it with velco.. whenever i want extra light.. it could help for a while before i change to new device huhuhu
Hi, aside from taking the phone apart, you would need some sort of tool to be able to get in that hole slightly and hook around the sim tray eject hole to gently drag out the sim tray.
Not sure, it can be caused my moisture exposure over time or excessive heat can loosen it as well. You can replace it with this replacement: www.ebay.com/itm/155008250046?hash=item24173630be:g:RFMAAOSwAdlhBEq1&amdata=enc%3AAQAHAAAA4HeCADtEdyPMVgJ6qJDeIuYjgpdiaCo0s2XQINKvlIGjRvuNOfZsQXCCt%2FmwBtZ8QwklsC%2F2yNK2Mw47M2X%2FhS1alFJWNoNX9ji%2FzT5hdRuPF82%2FHd5MaXcFjM7e%2F8xVy7pDY1KUs6UwA2McsET0IaD%2BpeauUJsiXzY%2FRWpQ2qIXiyw2zVDjj%2Bg%2BRgpv%2BmR7qWu851jx%2BnKsdbZjNO5VtBRyxioS4rqDezIl0flZE5XCrvhYdpEMxXH9jIl%2F3qbpFIn1hZit3TYfXdYwLZSYHSB5WdoIVCo2QJrnqWgAUNII%7Ctkp%3ABFBMxpnwtZdh
Having problem in A72 . Moisture detected .. Is it the problem in type c port or the logic board or the sensor ? if its sensor than ..which chip it is ?
Hi, not sure which one sets off that message, but you can try brushing out your charger port with an old tooth brush or taking apart the phone to brush off any corrosion inside or dry out any moisture.
The midframe itself is aluminium with a layer of plastic around the sides/frame of the phone. Its not a unibody aluminum frame if that's what you are asking.
Hey just wanted to know (since I get paranoid easily). I dropped my a72 and although there is no visible damage because of my good bezzeled cover and screen protector. Is there any chance for it to still have any internal damaged despite it looking absolutely fine? Is the internal built sturdy enough to survive a simple drop easily? I am just a bit concerned since this phone is indeed expensive. Do guide me.
I have been using my a72 for 3 months now. Suddenly whenever I shake my phone, it makes a rattling noise inside. Idk everything is working fine, but I'm nervous about it because I never drop the phone or anything else.
There are some components bellow the earpiece speaker on the board which can get hot and there is graphite film there as well which transfers the heat from those components from inside the phone to outside the phone.
dude i have sometging to tell you..my phone while im charging it its say trmperature too low but theres nothing waterlogo...pls help i cant charge my phone
It would be best to just disable the wifi from the phone, because disconnecting the antenna cable or antenna would just make the signal weak but does not mean it would completely turn off the wifi.
I don't have the skills to do that. It requires special companies with special computers and tools to be able to desolder the memory chip and get the info off of it. Its not a user removable chip. Soldered onto the main board.
Because most replacement screen assembly usually come with the mid frame pre installed so once you have taken all the parts out, you usually transfer them over to the new frame assembly. However I do mention how to replace the screen itself if you only bought a screen which was not with the frame (basically once you took everything apart as shown in the video, all that is left is to heat up and pry your old screen off the frame). I don't pry the working screen off since there is a high chance of damaging the working screen when prying it off.
Me:Watching this on a A72
My A72:There is no way that this video is not censored
👍
Wow samsung really improved
This is the one am waiting...thanks
You're welcome
hi, my a72 lcd is broken. Then I made it at the samsung service center .. water resistance is still working?
thank you very much. Does it have the same build quality and endurance as a52 or better or worse?
You're welcome. They have very similar build quality.
My a 72's touch screen became unresponsive a day ago, and now I can t even access settings. I've tried everything short of factory reset and disassembly, so I'm hoping maybe you might have some ideas on a solution?
Great video by the way, love the detailed instructions. Might try this if nothing else works.
same here
it just went black right?
Same, but I think it might be the new update or the flex cable ( 1:27 ), but I'm not sure yet, I'm gonna buy a flex cable and fix my phone, and MAYBE come back and tell you guys. Maybe.
Hello, I think my Samsung A72 has an issue with regards the backplate, it fell off and I'm guessing that Samsung has a poor glue residue. No history of repair though, what will I do? Thanks.
you can replace the adhesive with a new one. Here is a link for it: www.ebay.com/itm/234722749721?hash=item36a690ed19:g:v~MAAOSw5p1jPbYF&amdata=enc%3AAQAIAAAA4J74u5kvH8apIL1oMsB3gi%2Fe0J0H1ZH2zwsOszCqzcx12UXa%2Bq4sXROJgWNDUbySn3qU4spJfdqmBfk7%2F4X5sTM9BWdQeUbq60n9WTpWb070Nb9ucYzvNSt2XPxamT3u0dnx2FtUGVr9Pkvqoc9E9XLGAvLM4KMv14vtTtIvhMvkOFIBkZ3ArbdJ2mcDUSgvdmlDZpxaveFqk6IMlJwX3mAksu4qq%2FAu5saodXOs9C2h%2B3qU3tyz36sjC2QP67zN1O7mzh9f4ppNva4nRSz6WvGnKxLeteiqjaBUQMYR0Mnd%7Ctkp%3ABk9SR6TM3OrOYg
same, the left side (the one with no buttons) is coming off when the phone heats
Great quality video and details that I haven't seen on other disassembly ones. Thanks. I have a question, there are two pinholes on the top, one for the SIM/SD card slot. The other seems to be a microphone. What happens if you use the sim ejector on the mike hole. I would imagine Samsung Engineering would have accounted for that chance. Did they? Asking for a friend....
Thanks you. Nothing you should be fine, the mic sits above the hole so it wont be damaged.
Is the usb port easy replace? Is it a whole board replacement? I dont have much surface mount soldering experience, but I have the full setup.
You would just have to replace the sub board which has the charger port on it. For example like this one amzn.to/3ua80lX
Thanks for the great video! Could you tell me please what parts do I need to replace if my fingerprint sensor doesn't work? Will it work if I replace the sensor and the bottom board or I need the sensor only? Thank you!
You're welcome. You would only need to change the fingerprint sensor. Here is a link to one amzn.to/3CwJgce
Hi, I have a question:
My A72 stopped vibrating out of nowhere and sometimes the virbation returns whilest i'm tyling even though its a lot weaker. I also hear a rattling noise, but this is the camera assembly you said. Is this fixable without dissasembling the phone?
Thank you!
Thank you for the video. 👍
You're welcome
I got water inside my back camera. So I would like to know if i could remove the back and put it back by myself?
Do I need a glue or something?
Hi, yea you can heat it up with a hair dryer and pry it off. Make sure all the liquid inside the phone is dry and that there is no corrosion around any connectors or chips so it doesn't short later and damage your device. Then you can re apply your current back with new adhesive strip like this one: www.ebay.com/itm/155008250046?hash=item24173630be:g:RFMAAOSwAdlhBEq1 or you can get a new back cover that already has the adhesive pre installed, so all you do is peel off the film and apply it to your phone like this one: www.ebay.com/itm/115130401775?hash=item1ace4e83ef:g:hFQAAOSwdfdhreqb
Hello, my phone was soaked in a laundry water. Unfortunately, the back part was open (it was opened by a technician and didn't glue it properly)... Then there was a water inside (since it was open)... Is there a possibility that it will be repaire? Or should I buy a new one?
Most likely will be too badly damaged. The only way to tell is to open it up, disconnect the battery, dry it out completely, brush off any corrosion over the chips and connectors with a small brush and then test the phone to see if it will work. If not, you would then need to order working parts like the screen, battery, etc. to test and see which is not working or has gone bad.
Very good video! Thanks so match
Glad you liked it!
Hi! I dropped my samsung a72 in a water last week. At first i was not worried since its a waterproof phone but after letting it dry, i noticed that there is still a moisture visible inside the back cover of the phone. I literally panicked since the phone is just 9 months. Can there be any damages inside my phone?
Btw, the phone is working fine and there seems to be no damage on its functions.
Thank you!
i dropped mine in the washing machine but thankfully i got it out before it ran a full cycle.. did your phone not turn on too after you got it out of the water? what did you do to dry it out?
@PBKreviews On my A72, when i press the center of the back cover, I hear a plastic click. Then it should be the plastic that contains the graphite pad that probably has some play. Do you agree?
Yes correct. There is a slight space in between the back plate/battery door in some portions so that would be the reason you are able to press down and hear that.
@@PBKreviews Thanks! No need to worry then. Although these clicks shouldn't be expected in a Samsung phone imho. Nevertheless even some iPhone Max models have that, apparently...
I am noticing a bump/hump/ swell to the right side of the camera unit is it normal or something serious ? There is a slight battery draining issue and a slight heating issue near the camera unit when browsing.
My samsung a72 back cover fell off on its own. Thats why I was curious on how to glue the back cover without affecting the water resistance capability of the phone. But it looks like you didn't even glue it back? Is gluing it back enough? Or it has something more that is needed?
I don't show applying a new one in the video, but here is a link to the replacement adhesive needed to re apply the back. www.ebay.com/itm/234722749721?hash=item36a690ed19:g:v~MAAOSw5p1jPbYF&amdata=enc%3AAQAIAAAA4J74u5kvH8apIL1oMsB3gi%2Fe0J0H1ZH2zwsOszCqzcx12UXa%2Bq4sXROJgWNDUbySn3qU4spJfdqmBfk7%2F4X5sTM9BWdQeUbq60n9WTpWb070Nb9ucYzvNSt2XPxamT3u0aDNNFYR4jt6wZ1Zzfn6Erb1hFkLqaPOacoktKdunddqWkC%2FZlfBNE1Jy4ws0i37Z7odIT7TvxLcjPCtOAOBk%2Fd7A1gofxCCa%2F9Gxh%2B0%2BIRPXWqHK0PbdQU5QzpmQq74gQbtKr1MEvXl7Ysad0My4Zg62mkXiV%2FGaoe%2B%2BIJ3Pe6t%7Ctkp%3ABk9SR8rLgO3OYg
We have the same problem.
Hello, my Samsung A72 can't recognize the SIM, from what I've understood, I should replace the main flex cable and/or the sub-board. Is it correct? Thanks a lot.
Hi, no the sim reader is located on the main board and not the sub board. So would require a specialty shop that does soldering to be able to replace the sim reader on the main board.
Sad to see the mid frame cannot be replaced.. if you want your phone to look new in the long run, and you like to carry your phone around without a case, that's better off buying a new screen. But still, at least its got IP rating in exchange
Yup, replaceable frame housings have their pro's and cons and vice versa with the none replaceable frame housings.
Thank you bro
I like how they wrap the Processor with graphite, Do all processor cover like that?
most phones use a mix of thermal paste, graphite film and copper to draw heat away from the processor.
Can you specify the size of screws in the board because I am having trouble opening 2 screws on the board.
Hi, can you please tell what happen if i remove the graphite sheet over the speaker assembly ??? (minute 1:19)
Thanks!!
Hi, nothing will happen, its just there to help transfer some heat but its not a necessity for the speaker to function. Will work without it just fine.
Are the vibrations on this one like the one on the a52?
I don't remember, been a while since I used that phone
Thank you , one question : Galaxy A70 have graphite or something for cooling CPU ? Thank you again
You're welcome. Yes it has a layer of graphite on one side and thermal pads and heat transfer tape on the other side of the board.
Awesome, just swapped a screen over. Thanks a lot!
You're welcome.
شكرا
you're welcome
Nice video bro 👍🏻. I just recently dropped my phone and the screen goes all black. No damage on the body since I used case. One thing I noticed is the screen actually works even it's all black (it vibrates when I touch where the fingerprint scanner located). So then I tried to remove the back cover and suddenly the screen turned on and I can use it like nothing happened. But the probrem is when I put the back cover back on, the screen goes all black again. What could be the problem?
Hi, hmm that's odd. Might be a short or something. Try taking apart the phone and making sure all cables are attached and have not become disconnected. Also make sure everything is seated properly and see if that helps. If not, might be a defective screen.
Thanks bro, you help me
You're welcome
@@PBKreviews 👍 good content, keep doing this
@@mysocialmediaaccount270 thank you, will do
Hi there
The screen touch is unresponsive even after replacement with a new screen and it gets hot at the small chip on the main board
Thanks for the video
You're welcome
Hi sir, my main board is damage due to I dropped my Cellphone (A72) to the saltwater and it's already black screen and i cant charge also..is there a chance that I can retrieve my files and photos? please feedback :(
Hi, my A72 suddenly started to restart itself and only stops when the battery is drained, cannot start it and tried everything. Any clues on what to do next?
Could be many things. You would have to try a different battery to see if the battery has gone bad, or might be software issues, bad board, water damage etc.
My led lighting at camera burn i think.. now i can't use led light. So the led light cannot be replace? Am i right?
Ya, its soldered onto the board so it would require a place that is good at soldering and that can find the part to be able to replace it. Wouldn't be easy.
@@PBKreviews thankyou for explaining.. instead to repair.. i would like to find alternative way that more cheaper.. maybe use velco and glue it on my cover phone.. then use led lightning that i can buy from china and attach it with velco.. whenever i want extra light.. it could help for a while before i change to new device huhuhu
Hi. How to remove sim card slot if the pin hole not working (pin press cannot eject the slot)!? Thanks in advance.
Hi, aside from taking the phone apart, you would need some sort of tool to be able to get in that hole slightly and hook around the sim tray eject hole to gently drag out the sim tray.
Got any idea why the phones back plate adhiseve weaking. My phone's back plate just appears coming even though the battery is not bloated.
Not sure, it can be caused my moisture exposure over time or excessive heat can loosen it as well. You can replace it with this replacement: www.ebay.com/itm/155008250046?hash=item24173630be:g:RFMAAOSwAdlhBEq1&amdata=enc%3AAQAHAAAA4HeCADtEdyPMVgJ6qJDeIuYjgpdiaCo0s2XQINKvlIGjRvuNOfZsQXCCt%2FmwBtZ8QwklsC%2F2yNK2Mw47M2X%2FhS1alFJWNoNX9ji%2FzT5hdRuPF82%2FHd5MaXcFjM7e%2F8xVy7pDY1KUs6UwA2McsET0IaD%2BpeauUJsiXzY%2FRWpQ2qIXiyw2zVDjj%2Bg%2BRgpv%2BmR7qWu851jx%2BnKsdbZjNO5VtBRyxioS4rqDezIl0flZE5XCrvhYdpEMxXH9jIl%2F3qbpFIn1hZit3TYfXdYwLZSYHSB5WdoIVCo2QJrnqWgAUNII%7Ctkp%3ABFBMxpnwtZdh
not really nice but nice to see other people have the same issue, did you fix it?
I accidentally poked my a72 top microphone with sim injector,did I damage it and how about the waterproofing?
Hi, no you will be fine, the mic is seated above the hole and the filter will be fine as well.
even if I applied a force on it?
@@eisanonsol8771 yes because the filter is not seated against the hole and its above it, so would not be damaged
thanks 😊
Having problem in A72 . Moisture detected .. Is it the problem in type c port or the logic board or the sensor ? if its sensor than ..which chip it is ?
Hi, not sure which one sets off that message, but you can try brushing out your charger port with an old tooth brush or taking apart the phone to brush off any corrosion inside or dry out any moisture.
@@PBKreviews thank you
@@saheburrahman1213 You're welcome
Gi, I accidentally punctured my mic instead of the sim try. Could it be a problem? I tried everything but it seems working okau
Hi you should be fine, the mic sits above the hole so it wouldn't get damaged.
What the material on the side frame? Is it metal or plastic?
The midframe itself is aluminium with a layer of plastic around the sides/frame of the phone. Its not a unibody aluminum frame if that's what you are asking.
@@PBKreviews okay, thanks for letting me know!
you're welcome
@@PBKreviews what do you mean by midframe?
If you tear it down and put it back again is it still water resistant?
need to install new seal
correct :)
As previous com-mentor mentioned, would require new original pre cut adhesive seal to be installed to retain the water resistance.
Hey just wanted to know (since I get paranoid easily). I dropped my a72 and although there is no visible damage because of my good bezzeled cover and screen protector. Is there any chance for it to still have any internal damaged despite it looking absolutely fine? Is the internal built sturdy enough to survive a simple drop easily? I am just a bit concerned since this phone is indeed expensive. Do guide me.
Hi you should be fine. Unless you threw the phone against a wall or hit it really hard, a drop should not damage the internals.
When i shake my A72 i can hear "clicky sound", is that camera OIS?
Yeah or the camera assembly itself moving around.
@@PBKreviews thanks
I have been using my a72 for 3 months now. Suddenly whenever I shake my phone, it makes a rattling noise inside. Idk everything is working fine, but I'm nervous about it because I never drop the phone or anything else.
Hi, it's just the camera assembly rattling and its normal nothing to worry about :)
dude thats the camera...they are like chicken neck theyre moving..
Why does my a72 back gets warms where the earpiece speaker is located ??
There are some components bellow the earpiece speaker on the board which can get hot and there is graphite film there as well which transfers the heat from those components from inside the phone to outside the phone.
Does the water resistance gone after disasembly ?
yeah you need a waterproof seal again to make it waterproof
Correct :)
As the previous comment mentions, you would need to apply new original pre cut adhesive made for the phone to retain any water resistance.
dude i have sometging to tell you..my phone while im charging it its say trmperature too low but theres nothing waterlogo...pls help i cant charge my phone
The sub board/charger port board needs to be replaced.
Can someone tell me if its normal?
Mine was coming off and there was sticky glue too when it was coming out
What was coming off? the back cover? Its possible the adhesive went bad and needs new pre cut adhesive for the back plate/cover.
Oh man,i love your voice
lol, I'm sure your being sarcastic 😄 everyone always complains about it
@@PBKreviews whatt,,,no,,,,,,your voice sounds so smooth and relaxing for me
Is it possible to disconnect the wifi antenna?
It would be best to just disable the wifi from the phone, because disconnecting the antenna cable or antenna would just make the signal weak but does not mean it would completely turn off the wifi.
Is this the 4g model?
Yes
yes 4G model but its the same process and internal as the 5G, no difference aside from it supporting 5G and having an additional 5G antenna.
It’s lit 🔥
👍👍
interesting they put large graphite on the speaker bcz previos galaxy A series is overheating the speaker burning coil
hay sir where a thermostat sensor? my phone not charging because temperature to low
Hi, not sure where its located.
If i send and pay you to take my samsung Z flip apart so i can get the data that is stored on there, would you?
I don't have the skills to do that. It requires special companies with special computers and tools to be able to desolder the memory chip and get the info off of it. Its not a user removable chip. Soldered onto the main board.
@@PBKreviews thank you for getting back to me
@@dasbo1fan you're welcome
Battery link?
www.ebay.com/sch/i.html?_from=R40&_trksid=p4432023.m570.l1313&_nkw=eb-ba426aby&_sacat=0
Tnx
You're welcome
Nice
Thanks
Dude what music you're playing?
Its called Allégro - Emmit Fenn and its on the RUclips Studio audio library under free music.
@@PBKreviews thanks lot
@@carlandres3319 you're welcome
I love it...
👍
nice
Can you teardown Asus Zenfone 8?
yes, will do it once I get it in.
@@PBKreviews thx buddy
Is the graphite pad cooling worse than liquid cooling?
No its as good if not better. Lasts longer than vapor chambers since the vapors can evaporate over time.
💪
👍
I accidentaly tore mine apart for a small part
what do you mean
Please tear down moto g100,moto G10power and moto g 30
will look into it
Mimo 4х4?
not sure
They really dont use battery made by samsung themselves after note 7 lol
lol
This phone is a72
Why you cannot open display also 😂😂😂🤣🤣🤣
Because most replacement screen assembly usually come with the mid frame pre installed so once you have taken all the parts out, you usually transfer them over to the new frame assembly. However I do mention how to replace the screen itself if you only bought a screen which was not with the frame (basically once you took everything apart as shown in the video, all that is left is to heat up and pry your old screen off the frame). I don't pry the working screen off since there is a high chance of damaging the working screen when prying it off.