Sign up for Nebula for just $4/month to watch the the extended version of this video right now: nebula.tv/videos/strangeparts-how-we-built-a-250-lb-battlebot
You replied to a comment i made on this video and I replied back but i'm yet to hear an answer off you. If you have the time, i wouldn't mind a response please.
I think your design is really well I think it would be awesome if you coupled that with artificial intelligence I like how you can keep your weapon away and get it spinning up then drop it in on someone.
From my experience at BB my advice to new builders is don’t build your first combat robot trying to do things the “new way” brushless drive is far less reliable (but sometimes necessary due to space constraints). Also the Battlebots floor is really difficult to get good traction on so small, hard, smooth wheels are usually not the best choice if you have a high center of mass. With all that being said, tremendous props to this team and what they accomplished. I’m sure they learned all of those lessons before they even left the event. I love this video and the bot is a really neat concept and I’m sure they’ll be back even better next season!
I'm going to guess that with brushless motors you end up blowing up the controller boards pretty frequently... my experience with eletronic controllers is that they aren't particularly fond of vibration - getting sufficient isolation for the board so that it works reliably in competiton must be terribly difficult.
@@wrlprchnx I've never examined a failed speed controller board to determine cause of failure, however I would guess heat buildup due to large current demands and insufficient cooling would be the main causes of failure. Vibration failure can easily be overcome using polyethylene or a polymer resin to encase the parts so the components and circuit boards can't flex. Once that's done the components will be held rigidly in place. Heat dissipation will be your primary concern after that. The only method I know would be to used a water cooled heatsink that's also encased in the polymer resin making direct contact with the FETS using thermal epoxy. I'd consider using a couple of negative coefficient temperature sensors connected to a ESP-8266 to monitor temperature and control the cooling to critical components. Just my thoughts. Maybe you have alternative solutions you're considering.
I don’t understand how not tinning the wires caused a dead short. That sounds like something I’d say at work to cover up for a mistake I made that destroyed a piece of equipment 😂😂😂
@@alvieteal4980 Because wire for windings have coating(non conductive) so they dont short, when they crimped them, wire never made a proper connection to connector because of that coating, but when you solder you burn off that coating. In order to make proper connection with that kind of wire you need to scrape, sand or burn away that coating.
Greg is awesome! He had a goal over 20 years ago to work in robotics and he's achieved more than I think even he ever thought possible. He and I (with others) were co-founders of our university's robotics club (MDRC at RIT, go Tigers!). Best of luck Switchback team!
@Karl with a K Greg co-founded Rev Robotics which makes components for educational robotics systems, especially the international FIRST Robotics Competition that get hundreds of thousands of high school age students hands on involved with robotics every year. He and I go back almost 20 years and seeing how our discussions of what we wanted to do with our talents and skills have panned out, Greg is definitely doing what he wanted to do so many years ago. So to bring the experience he's gained from designing robot components for so many years back into BattleBots, which so heavily influenced all of us in that university robotics club so many years ago is great to see.
Same, I was suprised when he said at the start of the video that he was at REV headquarters, to see that these were the same guys that made my FRC & FTC parts
Nah its really annoying when you are from the Netherlands because shipping and customs are super expensive and you cant get the stuff from other places
@@joran4612 we always try to make it as easy as possible for teams all around the world, but international logistics is not easy or inexpensive. We are always trying to improve our process, please feel free to reach out to us with any concerns you have.
This is awesome, reminds me of my time with FIRST robotics, I miss those days. Cool to see this is at REV, I don't think we got parts from them until later on (2015/2016). Never had brushless motors though, they look awesome. Also, I love all of the robotics shirts. 2169 represent!
the vescs getting destroyed is a very common issue, try this: Solder a 50V TVS diode directly onto the pcb. Adding a low ESR cap also helps but that will increase bulk a lot. The vescs dying usually happen because of voltage spikes, tvs diodes and caps help with that a lot!
Your esc needs to be be rated 10 times the motor power rating because the way motors are rated is weird. You might need special rc buffered esc because the load is rather unpredictable.
Also the static buildup from spinners(which act like van de graaf generators) could mess them up I wonder if OHKOs by spinners that turned out to be receiver errors, happened that way in the show
Meaning if you have 4 wheel drive with 4 motors… that’s roughly over 8 grand. Double it due to testing and having spares, the cost exceeds 20 grand for just motors and escs
It's so weird to see pre-injury video now; because I kinda noticed something but didn't really think about it until after you said something. I'm really glad you're talking more about the hard to quantify effects of brain injury because I've had a couple different friends experience traumatic brain injuries and have their lives turned upside down just with the symptoms still left after everything was treated and "okay". I've always loved your work and I'll be sticking around for whatever you wind up doing even if you just want to start doing vlogs about living with the brain you've got. Either way you'd be providing really helpful and relatable information for people to live their lives better.
Looking back at his update video, He did say he was hit in the head by a falling pipe at a warehouse in Dallas in July. Which was when this video was originally shot :/
I was thinking the same thing, this bot looks too simple electronically to handle well. battle bot have been too concentrated in getting good mechanical design, but good electronics, sensors and microcontrollers is also really helpful in controlling. I wonder why few ever go past using simple RC parts, even a flight controller will help with stabilization
@@yuxuanhuang3523 I think the sheer amount of power being pumped through the systems may limit the complexity of the control systems. One of the other robots this year blew up 3 ESC's in their weapon setup, and had to revert to a spare that was only rated for 50amps. It took their spin up time out to 15s instead of the 3s they were used to from the (IIRC) 300amp setup they had grenaded. There are many reasons to stick with proven "dumb" systems, including ease of setup, ease of troubleshooting, peak current capability, reliability, ability to survive the combat environment, and overall cost. More complex systems tend to cost more, and add more failure points - and if a system can't survive being hit with a flamethrower, having a 100lb steel bar spinning at 250mph slammed into it, or being dropped from 12 feet up onto a floor made of 1/2" steel, potentially all at the same time, then the average roboteer won't use it.
Glad to hear you are on Nebula Scotty! And if anyone needs encouragement to join, I’ve had the Nebula/curiousity package for 2 years now and it’s absolutely worth it.
Agreed! I build non-combat robots and mentor FRC teams. One of my criteria for a team member to be anywhere close to a hot bot is "Are they sufficiently terrified?" This thing gave me chills!
Awesome to see you again Scotty, been missing your content, hope your recovery is going well and you're feeling better bud, take care All the best from the UK
I remember test driving my (small) robot the night before a competition and blowing a MOSFET after few minutes. Early morning the next day to get it replaced and ready. Really enjoying watching this.
Battlebots is my favorite tv show. + its the most real reality show ever i love robot fights big or small. i just wish it was more popular. its not a sport tho but its a real life video game.
and just how complicated it is just shows how talented the builders - teams are. because in the show they only have a matter of hours to get ready for another fight
I loved how switchback worked. When I first saw a picture of it I thought it would spin up, move the arm/rotate a bit and just go completely physics. Instead, it just worked fine. Sure it had some turning issues with the weapon extended since center of gravity, but other than that it worked beautifully and gave some pretty hard hits. Can't wait to see the improvements next season if you decide to re-enter.
Love you man. I do IT for work and as a hobbie but your videos have made me dive deeper into the electronics side of it than ever have before. You also began my journey down the rabbit hole of supply chains and where parts come from so that has eaten a terrifying amount of my time. Thank you and glad to see you making videos.
So good and refreshing to just see the FIRST logo out and about in a video that is not utterly and completely directly tied to FIRST. I think this might be my first time wondering upon this channel, but to my subscriptions this channel shall go!
To whomever has access to the closed captions, I think he's saying "I don't wanna lose the whole platoon" and not "I don't wanna lose the hopeful tune" at 0:08.
Yall should look into making a robot for NHRL, its a much more low-key fighting league that doesn't take itself nearly as overly serious as BB does. They also don't regulate what weapons you have so long as they aren't specifically designed for easily disabling other weapons (nets, ropes, emp devices, etc)
I would keep that steel armor playing, but I would want to put something similar to a ships hull on it. Maybe aluminium. Maybe even hard plastic. Something disposable and lightweight, just to get in the way before the actual armor is hit. But I don't know anything lmao. If I did, I'd be building my own bot
cool idea, but there are a few problems: 1. That works with projectiles and things that can be slowed down. Since the weapons are almost as big as the whole robot, they aren't going to slow down from a bit of soft material. The AR500 will do all the work when it comes to absorbing impact. 2. The judges use visual damage as a metric when the game goes the whole time. Chunks of aluminum and plastic are bad news in a close fight.
That Neblua ad was genuinely one of the first times in over a year that I have listened to the ad all the way through and was actually interested in the product. I certainly hope more content creators here plug it in future, as it sounds like a really good alternative to the growing tyranny of the popular “free-to-use” platforms. If I may ask, what was it that RUclips was having you cut? Did some sections contain too much “unacceptable” content, or was it mostly length/visibility related?
Nebula is a nearly five year old platform that thousands of youtubers have been shilling in all that time. They're still pushing it, and we still dont use it.
I'm guessing its mainly just length, especially since he mentioned the algorithm. Lots of creators on RUclips that do longform videos complain about longer videos not working well with the algorithm.
Some improvement ideas: Remove the chain drive and use 4 smaller motors Definitely add heatpipes to all critical parts Maybe even split the spinner into 2 counter rotating sections which cancels the gyroscopic force offset to enable faster turns
"The resistance was infinite so essentially a dead short" That is 2 completely opposite states of resistance, not remotely the same. High resistance is the exact opposite of a short.
I think what he meant was that the controller had to crank up the output to overcome the resistance, and that increased current output made the controller act similar to a dead short scenario. They clearly at least *somewhat* know what they're doing, so I'll give em the benefit of the doubt here.
@@Amy_A. I have another explanation. It is a three-phase motor, and when one cable is not connected properly, the motor will not spin because two cables connect through one coil. What might have happened was that one connected coil was acting as a short because it was passing DC current. What should have happened in a spinning motor was AC passing through all three coil at 120 degree apart phases.
I agree this was just a misspeak, but I think he's also onto the wrong idea - I've never seen a motor controller where it blows up without connection to a load.
Hey here's something that no bot builder has thought of. Installing limited slip clutches on their weapons and arms. I built recycling plants that wash tank paddles would jam up under excess waste material. to fix this, I added spring loaded clutch plates to the motor so that it would spin under power, but if the counter force was too much, the clutch plates would slip saving a lot of chains and sprockets. Your weapon stops abruptly on contact. A limited slip clutch would prevent it from burning out from excess load.
Believe it or not, clutches have been used since the very beginning of robot combat. Anything beneficial that you can readily think of has been done already. Especially something as simple as a clutch.
@@bldjln3158 I've watched every build vid from Blip to sawblaze and not one has incorporated a clutch. The mechanical engineer in me gets frustrated when I see spinners being installed as diirect/chain drive without so much as a single measure of protection. Electronically, these machines are sound as a pound, but mechanically they could use some expertise.
Only seen you got a head injury now. Sorry to hear hope you heal quickly. I've had a bad year due to problems with my kidney and it's just put a damper on a already existing financial situation, us as humans really take good health for granted especially when your type of work is physical. All I can say is I hope you heal quick and soon. Keep up the good job on these amazing engineering videos.
we use a lot of rev robotics parts in our robots that we build for robotics. This was a REALLY COOL video knowing that you were invited to their Warehouse. Keep up the good work!
This is genuinely the most exciting thing I've ever watched! What a group of great people with brains and skills to match! Great to see you triumphantly return Scotty! 👍
Paused at 13:51 - immediate first impression- fewer blades would be better. Reduce strain on complex arm components plus more kinetic force would be distributed to each remaining blade, like a bed of nails, too many equals less damage per cutting surface. Someone with math chops could provide a functional equation for this idea.
You sold me INSTANTLY on Curiosity Stream and Nebula. Love your content and "like minded" content. Thanks for everything you do and look forward to seeing more of your content on any/all streaming platforms! :)
the discovery plus links are not working.... it doesn't take you to the fight :| .... or may be coz it's not available in India?????? Can you provide all fight links from youtube?
That was such a great and enjoyable video! I'm glad you got to do this, and are also well enough now to produce content again :) It's amazing to have ya back, can't wait for your next projects, and I'm on my way to watch that free fight now :3
Very ironically I had a concussion a little whiles ago, I was very lucky to read up on treatment of concussions due to your video. I've recovered almost fully now, but it was pretty scary when it happened and I couldn't speak properly
when the guy figured out that the short was from crimping the connection at mfg level, with the increased load you guys applied... i decided to sub to the channel. im an ex-engineer, and i have to say, this is a beautiful video that demonstrates so much fun with knowledge about the development process and how much there is to know about making things from scratch. it reminds me of the projects i got to work on, and how lucky I was. this was inspiring :)
Back in the 90s and early 2000s, robots with small teams and meager budgets could feasibly win a championship, but that's not been a likelihood since Battlebots came back in 2015 - now it's all 5 figure budgets, sponsorship deals and typically large teams.
Loved the video, gonna have to watch the fights later. The moment you did the nebula Ad I ditched to Nebula, got a subscription but I never remember to watch people on there instead of RUclips
8:53 If the resistance goes to infinite, it is the opposite of a dead short! Also with infinite resistance you are not able to bump the current, because you would need a massive high voltage to do so, like lightning voltage high. If you want to learn more, look up Ohms law.
@@BrainHurricanes pretty patronising to tell people that probably have degrees in engineering to look up the single most fundamental law in electronics.
@@Validifyed No patronizing intended, but I understand you can feel it that way. You don't need a degree to build great things, they are only tools, just like Ohms law.
This is so interesting! I love watching stuff like this because I was on a FIRST robotics team and got second in regionals the year I competed. It was honestly a super fun time!
Ohhhh man so good to see you're well. Fantastic video. Had to think about you a lot since the wife of a friend of mine has a similar brain concussion as well. So good to see it is getting so well.
For my bachelor in electrical engineering I had several projects during the 3 years. One of them was making a skateboard with a brushless motor. None of the teams got it to work. The motor was turning (more or) less effectively for all projects but the entire electric skateboard didn't really work in the end. They are really annoying. I guess it is easier if you are allowed to use motor drivers or other assistance.
anyone else remember that mythbusters episode how they're all behind the polycarbonate screen thinking it was bullet proof, only to find it's not? it depends on the thickness of the material. the thickness you have there isn't enough to stop high velocity, heavy objects. stack 3 of those shields and you'd be pretty safe
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
Sign up for Nebula for just $4/month to watch the the extended version of this video right now: nebula.tv/videos/strangeparts-how-we-built-a-250-lb-battlebot
You replied to a comment i made on this video and I replied back but i'm yet to hear an answer off you. If you have the time, i wouldn't mind a response please.
I love you guys, but the last thing I need in my life is ANOTHER streaming platform... Best of luck to you with that.
Most important question. Is that a cup from Dickey's BBQ? At 9:12
I think your design is really well I think it would be awesome if you coupled that with artificial intelligence I like how you can keep your weapon away and get it spinning up then drop it in on someone.
Has it won any battles yet?
From my experience at BB my advice to new builders is don’t build your first combat robot trying to do things the “new way” brushless drive is far less reliable (but sometimes necessary due to space constraints). Also the Battlebots floor is really difficult to get good traction on so small, hard, smooth wheels are usually not the best choice if you have a high center of mass. With all that being said, tremendous props to this team and what they accomplished. I’m sure they learned all of those lessons before they even left the event. I love this video and the bot is a really neat concept and I’m sure they’ll be back even better next season!
I'm going to guess that with brushless motors you end up blowing up the controller boards pretty frequently... my experience with eletronic controllers is that they aren't particularly fond of vibration - getting sufficient isolation for the board so that it works reliably in competiton must be terribly difficult.
@@wrlprchnx I've never examined a failed speed controller board to determine cause of failure, however I would guess heat buildup due to large current demands and insufficient cooling would be the main causes of failure. Vibration failure can easily be overcome using polyethylene or a polymer resin to encase the parts so the components and circuit boards can't flex. Once that's done the components will be held rigidly in place. Heat dissipation will be your primary concern after that. The only method I know would be to used a water cooled heatsink that's also encased in the polymer resin making direct contact with the FETS using thermal epoxy. I'd consider using a couple of negative coefficient temperature sensors connected to a ESP-8266 to monitor temperature and control the cooling to critical components. Just my thoughts. Maybe you have alternative solutions you're considering.
I don’t understand how not tinning the wires caused a dead short. That sounds like something I’d say at work to cover up for a mistake I made that destroyed a piece of equipment 😂😂😂
@@wrlprchnx it’s dumb easy and most of us let the ESCs just flop around inside the robot. It’s overdraw causing them to burn up that usually kills.
@@alvieteal4980 Because wire for windings have coating(non conductive) so they dont short, when they crimped them, wire never made a proper connection to connector because of that coating, but when you solder you burn off that coating. In order to make proper connection with that kind of wire you need to scrape, sand or burn away that coating.
Greg is awesome! He had a goal over 20 years ago to work in robotics and he's achieved more than I think even he ever thought possible. He and I (with others) were co-founders of our university's robotics club (MDRC at RIT, go Tigers!). Best of luck Switchback team!
its been quite the ride.....🙂
@Karl with a K Greg co-founded Rev Robotics which makes components for educational robotics systems, especially the international FIRST Robotics Competition that get hundreds of thousands of high school age students hands on involved with robotics every year. He and I go back almost 20 years and seeing how our discussions of what we wanted to do with our talents and skills have panned out, Greg is definitely doing what he wanted to do so many years ago. So to bring the experience he's gained from designing robot components for so many years back into BattleBots, which so heavily influenced all of us in that university robotics club so many years ago is great to see.
@@karlwithak.Post the video. I want to see it
Awesome to see a bunch of REV Robotics people on a channel I like, they're super helpful when it comes to my FIRST teams.
The REV folks are wonderful. I met Greg in China, and had a blast meeting and making friends with everyone else while I was in Dallas.
Same, I was suprised when he said at the start of the video that he was at REV headquarters, to see that these were the same guys that made my FRC & FTC parts
Nah its really annoying when you are from the Netherlands because shipping and customs are super expensive and you cant get the stuff from other places
@@joran4612 we always try to make it as easy as possible for teams all around the world, but international logistics is not easy or inexpensive. We are always trying to improve our process, please feel free to reach out to us with any concerns you have.
This is awesome, reminds me of my time with FIRST robotics, I miss those days. Cool to see this is at REV, I don't think we got parts from them until later on (2015/2016). Never had brushless motors though, they look awesome.
Also, I love all of the robotics shirts. 2169 represent!
the vescs getting destroyed is a very common issue, try this: Solder a 50V TVS diode directly onto the pcb. Adding a low ESR cap also helps but that will increase bulk a lot.
The vescs dying usually happen because of voltage spikes, tvs diodes and caps help with that a lot!
Your esc needs to be be rated 10 times the motor power rating because the way motors are rated is weird. You might need special rc buffered esc because the load is rather unpredictable.
by RC i mean resistor-capacitor in series connected to all three phases of each output
Could also design it so that your ESCs sink heat into your frame.
Also the static buildup from spinners(which act like van de graaf generators) could mess them up
I wonder if OHKOs by spinners that turned out to be receiver errors, happened that way in the show
The ESCs and Motors alone cost well over a thousand for battlebots of this size 😭
Meaning if you have 4 wheel drive with 4 motors… that’s roughly over 8 grand. Double it due to testing and having spares, the cost exceeds 20 grand for just motors and escs
It's so weird to see pre-injury video now; because I kinda noticed something but didn't really think about it until after you said something. I'm really glad you're talking more about the hard to quantify effects of brain injury because I've had a couple different friends experience traumatic brain injuries and have their lives turned upside down just with the symptoms still left after everything was treated and "okay".
I've always loved your work and I'll be sticking around for whatever you wind up doing even if you just want to start doing vlogs about living with the brain you've got. Either way you'd be providing really helpful and relatable information for people to live their lives better.
Looking back at his update video, He did say he was hit in the head by a falling pipe at a warehouse in Dallas in July. Which was when this video was originally shot :/
@@manorin i think you're on top something
glad to see more of your videos hope you are doing better thanks for the great videos
I second that
When it's spinning at top speed, the steer torque will be impressive. Turning a corner could well flip it over.
If it turns using tank steering and raises blade it would probably do ok
something something Wrecks, something something highest kinetic energy spinner at the show.
spin it the right way and it could be gravitationally stabilized no matter how you flip it over! :P
I was thinking the same thing, this bot looks too simple electronically to handle well. battle bot have been too concentrated in getting good mechanical design, but good electronics, sensors and microcontrollers is also really helpful in controlling. I wonder why few ever go past using simple RC parts, even a flight controller will help with stabilization
@@yuxuanhuang3523 I think the sheer amount of power being pumped through the systems may limit the complexity of the control systems. One of the other robots this year blew up 3 ESC's in their weapon setup, and had to revert to a spare that was only rated for 50amps. It took their spin up time out to 15s instead of the 3s they were used to from the (IIRC) 300amp setup they had grenaded.
There are many reasons to stick with proven "dumb" systems, including ease of setup, ease of troubleshooting, peak current capability, reliability, ability to survive the combat environment, and overall cost. More complex systems tend to cost more, and add more failure points - and if a system can't survive being hit with a flamethrower, having a 100lb steel bar spinning at 250mph slammed into it, or being dropped from 12 feet up onto a floor made of 1/2" steel, potentially all at the same time, then the average roboteer won't use it.
Glad to hear you are on Nebula Scotty! And if anyone needs encouragement to join, I’ve had the Nebula/curiousity package for 2 years now and it’s absolutely worth it.
Just signed up for curiosity stream, but I cant see how to access Nebula from there. Is it Geo Restricted to the USA or something?
The comment I was looking for. Thank you.
MAJOR kudos to the safety mindset on this build!! what a great team to be safe and produce a great product.
Agreed! I build non-combat robots and mentor FRC teams.
One of my criteria for a team member to be anywhere close to a hot bot is "Are they sufficiently terrified?"
This thing gave me chills!
Awesome to see you again Scotty, been missing your content, hope your recovery is going well and you're feeling better bud, take care
All the best from the UK
I remember test driving my (small) robot the night before a competition and blowing a MOSFET after few minutes. Early morning the next day to get it replaced and ready. Really enjoying watching this.
The REV team is so incredible. I only got to interact with them occasionally at FIRST champs, but theyre such a kind group of people!
Nice to hear your voice again sir, great video as always. You talents and experiences are always a pleasure to watch. be safe and good health always!
Battlebots is my favorite tv show. + its the most real reality show ever
i love robot fights big or small. i just wish it was more popular. its not a sport tho but its a real life video game.
and just how complicated it is just shows how talented the builders - teams are. because in the show they only have a matter of hours to get ready for another fight
I loved how switchback worked. When I first saw a picture of it I thought it would spin up, move the arm/rotate a bit and just go completely physics.
Instead, it just worked fine. Sure it had some turning issues with the weapon extended since center of gravity, but other than that it worked beautifully and gave some pretty hard hits.
Can't wait to see the improvements next season if you decide to re-enter.
My Nebula subscription was happily paid for by the can shaking bit in your extended version of this video over there. Well done!
That was hilarious.
Man seeing such a heavy thing spin st 10k rpm is truly terrifying
“Its important to design your robot for the oven that you have”
Im dead 😂
I know from experience that worm gears are hard to run in combat robots - makes switchback even more impressive.
Glad to see you again in shape ! Keep the good work ! You rock .
9:13 is the most engineering thing ive ever seen
Love you man. I do IT for work and as a hobbie but your videos have made me dive deeper into the electronics side of it than ever have before. You also began my journey down the rabbit hole of supply chains and where parts come from so that has eaten a terrifying amount of my time. Thank you and glad to see you making videos.
That explanation of the wire windings crimp was god damned phenomenal. I re-watched that explanation a few times.
Thank you for showing proper combat robot safety protocols!
So good and refreshing to just see the FIRST logo out and about in a video that is not utterly and completely directly tied to FIRST. I think this might be my first time wondering upon this channel, but to my subscriptions this channel shall go!
To whomever has access to the closed captions, I think he's saying "I don't wanna lose the whole platoon" and not "I don't wanna lose the hopeful tune" at 0:08.
It is auto-generated.
Yall should look into making a robot for NHRL, its a much more low-key fighting league that doesn't take itself nearly as overly serious as BB does. They also don't regulate what weapons you have so long as they aren't specifically designed for easily disabling other weapons (nets, ropes, emp devices, etc)
....AFTER SEEING THEIR PERFORMANCE...KINDA....YEAH,agree....
....BECAUSE MAYBE THIS WAY THEY WONT BE SO EMBARRASSING
@@robotnikkkk001 LMAO YEAH
I would keep that steel armor playing, but I would want to put something similar to a ships hull on it. Maybe aluminium. Maybe even hard plastic. Something disposable and lightweight, just to get in the way before the actual armor is hit.
But I don't know anything lmao. If I did, I'd be building my own bot
cool idea, but there are a few problems:
1. That works with projectiles and things that can be slowed down. Since the weapons are almost as big as the whole robot, they aren't going to slow down from a bit of soft material. The AR500 will do all the work when it comes to absorbing impact.
2. The judges use visual damage as a metric when the game goes the whole time. Chunks of aluminum and plastic are bad news in a close fight.
That Neblua ad was genuinely one of the first times in over a year that I have listened to the ad all the way through and was actually interested in the product. I certainly hope more content creators here plug it in future, as it sounds like a really good alternative to the growing tyranny of the popular “free-to-use” platforms.
If I may ask, what was it that RUclips was having you cut? Did some sections contain too much “unacceptable” content, or was it mostly length/visibility related?
Nebula is a nearly five year old platform that thousands of youtubers have been shilling in all that time.
They're still pushing it, and we still dont use it.
I'm guessing its mainly just length, especially since he mentioned the algorithm. Lots of creators on RUclips that do longform videos complain about longer videos not working well with the algorithm.
Some improvement ideas:
Remove the chain drive and use 4 smaller motors
Definitely add heatpipes to all critical parts
Maybe even split the spinner into 2 counter rotating sections which cancels the gyroscopic force offset to enable faster turns
Counter-rotating wouldn't work because you want the whole thing impacting at once in one direction to impart force into the other bot.
@@inthefade yes I thought so as well...
Another downside would be that the bot flips itself in the opposing direction
"The resistance was infinite so essentially a dead short"
That is 2 completely opposite states of resistance, not remotely the same.
High resistance is the exact opposite of a short.
I think what he meant was that the controller had to crank up the output to overcome the resistance, and that increased current output made the controller act similar to a dead short scenario. They clearly at least *somewhat* know what they're doing, so I'll give em the benefit of the doubt here.
@@Amy_A. I have another explanation. It is a three-phase motor, and when one cable is not connected properly, the motor will not spin because two cables connect through one coil. What might have happened was that one connected coil was acting as a short because it was passing DC current.
What should have happened in a spinning motor was AC passing through all three coil at 120 degree apart phases.
Obviously just a miss speak. Like it does not matter.
I agree this was just a misspeak, but I think he's also onto the wrong idea - I've never seen a motor controller where it blows up without connection to a load.
Hey here's something that no bot builder has thought of. Installing limited slip clutches on their weapons and arms. I built recycling plants that wash tank paddles would jam up under excess waste material. to fix this, I added spring loaded clutch plates to the motor so that it would spin under power, but if the counter force was too much, the clutch plates would slip saving a lot of chains and sprockets. Your weapon stops abruptly on contact. A limited slip clutch would prevent it from burning out from excess load.
Believe it or not, clutches have been used since the very beginning of robot combat. Anything beneficial that you can readily think of has been done already. Especially something as simple as a clutch.
@@bldjln3158 I've watched every build vid from Blip to sawblaze and not one has incorporated a clutch. The mechanical engineer in me gets frustrated when I see spinners being installed as diirect/chain drive without so much as a single measure of protection. Electronically, these machines are sound as a pound, but mechanically they could use some expertise.
Love to see what we been missed to carry on and pick it up, not the program only, but you, Scott, all are well. Keep it up
I would binge a whole Netflix Series about you guys on your way to BattleBots no question!
Only seen you got a head injury now. Sorry to hear hope you heal quickly. I've had a bad year due to problems with my kidney and it's just put a damper on a already existing financial situation, us as humans really take good health for granted especially when your type of work is physical. All I can say is I hope you heal quick and soon. Keep up the good job on these amazing engineering videos.
“So we’ve lost drive on one half of the robot”
Welcome to Battlebots where losing drive is pretty much obligatory. 😜
It's so nice to have you back Sir! Hope you are well and hope you never stop uploading your awesome content!
this was so incredibly cool!!! thank you for showcasing such great engineering
Were so glad to see you! This video was EPIC! You never disappoint. Thank you
Glad you're feeling better. Concussions are no joke. Robots are more like a bonus! :)
I'm glad you were finally able to make this video, it was great seeing the Strange Parts logo on TV!
I'M SO GLAD YOU'RE BACK!!!
we use a lot of rev robotics parts in our robots that we build for robotics.
This was a REALLY COOL video knowing that you were invited to their Warehouse. Keep up the good work!
This is genuinely the most exciting thing I've ever watched! What a group of great people with brains and skills to match!
Great to see you triumphantly return Scotty! 👍
Paused at 13:51 - immediate first impression- fewer blades would be better. Reduce strain on complex arm components plus more kinetic force would be distributed to each remaining blade, like a bed of nails, too many equals less damage per cutting surface. Someone with math chops could provide a functional equation for this idea.
Kinda a longshot, but I'd love a collab between you and diy perks.
Hopeful and still praying for your health and the future of your channel scotty. Don’t ever give up on your amazing passion. Chin up.
YO ITS SWITCHBACK FROM BATTLEBOTS YO WHATS UP!
I hope your are getting better and better after the injury, but from this video, it looks like you do ! ♥
It's great to see you back :) Really enjoyed this video - can't wait to see more from this team.
Glad to see your videos popping up in my feed again. Hope you're making a good recovery from the accident :)
You inspired me to study engineering. I love your videos, it is great to see you again.
You sold me INSTANTLY on Curiosity Stream and Nebula. Love your content and "like minded" content. Thanks for everything you do and look forward to seeing more of your content on any/all streaming platforms! :)
Same here, have been seeing that promoted by many other creators including wendover etc, but... pulled the trigger when Scotty mentioned it!
been waiting for this content for so long, glad to see you back and hope your health is good!
the discovery plus links are not working.... it doesn't take you to the fight :| .... or may be coz it's not available in India?????? Can you provide all fight links from youtube?
actually with the thickness of those plates you don't need to preheat AR500, you only need to preheat for greater thickness (more than 3/8")
Thanks for the great video. I'm happy that it seems like you've now made a complete recovery.
That was such a great and enjoyable video! I'm glad you got to do this, and are also well enough now to produce content again :)
It's amazing to have ya back, can't wait for your next projects, and I'm on my way to watch that free fight now :3
Welcome back Scotty. Can't wait to see your full creativity continue to come back to life.
Im so happy your doing better and posting again. I love the content.
Glad to see ...you are return on field projects ... Stay healthy, safe and alert.... Love from India..🇮🇳
Very ironically I had a concussion a little whiles ago, I was very lucky to read up on treatment of concussions due to your video. I've recovered almost fully now, but it was pretty scary when it happened and I couldn't speak properly
when the guy figured out that the short was from crimping the connection at mfg level, with the increased load you guys applied... i decided to sub to the channel. im an ex-engineer, and i have to say, this is a beautiful video that demonstrates so much fun with knowledge about the development process and how much there is to know about making things from scratch. it reminds me of the projects i got to work on, and how lucky I was. this was inspiring :)
Scotty never disappoints when that notification drops!
8:00 - I don’t agree with the enamel coated winding wires but whatever. Google using aspirin and a soldering iron to remove winding wire enamel
I saw switch back live in Vegas! Looking forward to seeing V2!
It always feels like a treat to see a new video of yours. Thank you for continued content!
Glad you're posting again. Hope you are feeling better!
We're Battle Bots ever actually built in garages by small teams, and did they ever win?
Back in the 90s and early 2000s, robots with small teams and meager budgets could feasibly win a championship, but that's not been a likelihood since Battlebots came back in 2015 - now it's all 5 figure budgets, sponsorship deals and typically large teams.
@@Matt-cn2nn I wonder if a sportsman/grassroots class could help
Loved the video, gonna have to watch the fights later. The moment you did the nebula Ad I ditched to Nebula, got a subscription but I never remember to watch people on there instead of RUclips
The extra content was amazing and it’s sad the algorithm hated it
Glad to see you posting again! we missed you. Hope youre healing up!!
my favorite line "its important to design robot for the oven you have" dying here
Glad to have you back mate! You're a gem.
Awesome. I enjoyed watching the build. I know y'all had a blast with this!
The can shaking part is honestly so funny, I didn't expect that ,those guys know how to build robots and also jokes
Great video, thanks:)
8:53 If the resistance goes to infinite, it is the opposite of a dead short!
Also with infinite resistance you are not able to bump the current, because you would need a massive high voltage to do so, like lightning voltage high.
If you want to learn more, look up Ohms law.
Pretty sure everyone in this video knew about ohmes law when they where 12
@@Validifyed If he knew from the age of 12, he wouldn't say: "So your resistance went to infinite, and it was essentially a dead short'
@@BrainHurricanes pretty patronising to tell people that probably have degrees in engineering to look up the single most fundamental law in electronics.
@@Validifyed No patronizing intended, but I understand you can feel it that way. You don't need a degree to build great things, they are only tools, just like Ohms law.
Excited to see you back, hope you've had a full recovery!
So glad to see you back in videos. Glad you're improving!
And thus, an amazing BattleBot was created. It’s so interesting to see the origin of Switchback and how it was created.
This is so interesting! I love watching stuff like this because I was on a FIRST robotics team and got second in regionals the year I competed. It was honestly a super fun time!
Ohhhh man so good to see you're well. Fantastic video. Had to think about you a lot since the wife of a friend of mine has a similar brain concussion as well. So good to see it is getting so well.
17:30 That is a testament to the balance of those blades.
Awesome to see your content again Scotty!
Hoping you're feeling better!
Thanks!
Thank you Franklin!
oh you're back! Good, been waiting for your videos
I actually work with frank for first and he is a really nice mentor and helpful and it is fun to see him do this
Glad to see u back in yt. Love your content. Always blow my mind
18:55 Link to that bonus fight available on youtube? Even if it's no longer available, I'm curious to know about this footage.
man iv'e had a head injury as well i hope you recover with no complications man
For my bachelor in electrical engineering I had several projects during the 3 years. One of them was making a skateboard with a brushless motor. None of the teams got it to work. The motor was turning (more or) less effectively for all projects but the entire electric skateboard didn't really work in the end. They are really annoying. I guess it is easier if you are allowed to use motor drivers or other assistance.
Great to know you're back, I missed you!
Great to see that you are getting better and making videos again
Welcome back
anyone else remember that mythbusters episode how they're all behind the polycarbonate screen thinking it was bullet proof, only to find it's not?
it depends on the thickness of the material. the thickness you have there isn't enough to stop high velocity, heavy objects. stack 3 of those shields and you'd be pretty safe
Did you see what they had holding it up?
Hey Welcome back. Was worth waiting for you. 👍🥳
Really great to to have the super likeable scotty back on my screen
That looks like an awesome battle monster. Great to hear your head is all better man! Welcome back!
Happy to see you better! Thanks for the video 🙏
dude. I'm so glad to see you looking and feeling good!!! I've missed your channel!!!
right? this is new?