This will work but only if you only turn it off from one pair of switches. If it is off from the left pair, nothing you do with the right two switches will turn it on. Replacing the two middle switches with DPDT switchs that reverse the traveling wires will make it work from any location.
absolutely correct, instead of switches that make a permanent connection once pressed, they'd better use a door bell button, of course with the same look as any other normal switch, and a relais, then you can have up to dozens of (door bell button) switches.
@@renemeier9057 it is called télérupteur in france it works with a coil and push buttons dpdt switches are not allowed anymore that is according to norms what you have to install as soon as there are more than two switches controlling a light otherwise the set with two 3ways only that we call other wise (cause in fact they are only two-ways) are still in use I knew right away there was something wrong thanks for sharing : )
This wirig is totally wrong!!! If the right side is switched off, the you cannot switch on the light on the left side! The middle two switches have to be X (4connectors) and not V (3 connectors) ----------
Wrong Connection, Misleading Video If the first two two way switches are placed in OFF position (One On and Other one OFF) then phase will not pass to the last two switches, then how can you turn ON the bulb using the last two switches Also the animation shown is wrong, the bulb should glow if the two switches are placed in either both in ON (downword)or both in OFF(upword), and the bulb should turn off if any one switch in placed in On(downword) and other in OFF(upword)
@@wittydisplayname1761 No. When interrupteur, 1 is open ,2 close ...no current go. So,if you clic on 3 or 4 ..no work..no work. For 3 and 4 , is work. 1 and 2 same position If 1 and 2 no same position..3 ,4 don't work
@@pierrebreton1153 I think I see what you are saying, Pierre. I think if the light was on you could turn it off from any switch but if the light was off you could not necessarily turn it on from any switch because the circuit might be broken in 1 or 2 and nothing 3 or 4 does can change that…and visa versa.
@@Gilbert208 en France il y a une norme, 2 points d'allumage = va et vient, 3 points d'allumage = permutateur possible, à partir de 4 points d'allumage c'est télérupteurs. Aucune chance d'obtenir le consuel avec un bricolage comme ça qui en plus ne fonctionne pas. Les normes électriques US me font peur...
It doesn't work perfectly... if you change the state of 1st or 2nd switch, turning off the light, then the 3th or 4th switch can't control the lamp... In really, the circuit acts a AND logical function, where 1-2 switches are in series with 3-4 switches...
Pero el salto a los otras llaves d combinación( par opuesto) no es posible si desde su complemento no la habilita. Pero igual está muy interesante el circuito, un abrazo desde Uruguay 🤜🏼🤛🏼
Although a great graphic, installing two pairs of 3-way switches connected as shown, will NOT work as shown. If there is no voltage coming from the first pair, there is nothing that can be done by changing either of the other pair of switches that will work because of no voltage at third or fourth switch.
Sí el par de llaves 1 y 2 no dejan encendida la lámpara, no es posible actuarla desde las llaves 3 y 4. Igualmente si la llaves 3 y 4 la dejan apagada, para las llaves 1 y 2.
Неполноценная схема. Будет работать только при соблюдении определённых положений переключателей. Выключаться будет каким угодно переключателем, а вот включаться только из той пары, из которой выключали и которые связаны по двухпроводке (1и2 или 3и4).
согласен, тоже смотрел раза два, думал может что упустил, но нет. Не всегда есть возможность включить свет одним выключателем, а выключить другим, и наоборот выключить одним, а включить другим
Nice graphics, but your circuitry is flawed. Only the outer switches can be 3 way. The center ones need to be 4 way in order for it to work properly. It's the sort of mistake a lot of non-electricians make.
Não funciona. Se qualquer um dos dois primeiros interruptores estiver desligado a energia não vai chegar no terceiro. Por isso existe o interruptor PARALELO/INTERMEDIÁRIO de 04 pinos.
@@valdecidepaula3709 nem precisa testar esse circuito aí, sou engenheiro eletricista e sei que não funciona. Interruptores intermediarios (4 pinos) são feitos pra isso, pois evitam esse problema que ocorre na ligação que o sujeito está espalhando por aí. Sempre tem que haver 02 condutores entre os interruptores.
Soy Electricista Profesional , esta manera o ckto , no funcionará ya que en algún momento una llave quedará abierta y no encenderá de ningún otro punto . para esta instalación se necesita obligatoriamente dados de 4 vías.
It's 4-way AND gate, meaning this circuit will close only if all four switches are closed. But, since we can turn off this circuit just by opening only one circuit, it has to be AND
This circuit don't work for all states. For example you cant turn on the lamp by one SW in left pairs if you turned it off by one SW in the right pairs. This never works properly.
From figure given, let us say all switches are on ( coz all switches are upper pressed), so the bulb is lighted. Let us label first the four switches namely from the left, A, B, C and D. What will happen then, if: Leftmost switch (A) is swicth off (lower pressed). Then, the connection or continuity line of switches A and B is disconnected. Then the bulb lights off. With the above condition (A is disconnected with B, coz A is lower pressed and B is upper pressed), What if You're located near switches C and D, how can you turn on the bulb/light by switching C or D? Switches group A & B will work just by themselves, as well as switches group C & D will work just by themselves. If both groups are connected to each other, ie, as what shown in the figure, the connection of the two groups' line continuity cannot be proven or established to be always connected.
Não funciona. Se qualquer um dos dois primeiros interruptores estiver desligado a energia não vai chegar no terceiro. Por isso existe o interruptor PARALELO/INTERMEDIÁRIO de 04 pinos.
Não funciona. Se qualquer um dos dois primeiros interruptores estiver desligado a energia não vai chegar no terceiro. Por isso existe o interruptor PARALELO/INTERMEDIÁRIO de 04 pinos.
@@branddo sim, é sério. Sou engenheiro eletricista! Para esse circuito funcionar precisa usar 02 interruptores intermediarios (4 way, intermediários ou inversores, depende da região o nome muda). E sempre usar um par de fios , que é onde esse circuito fracassa, pois se cortar a energia se um lado, ainda podemos ligar para o outro lado!
Não funciona. Se qualquer um dos dois primeiros interruptores estiver desligado a energia não vai chegar no terceiro. Por isso existe o interruptor PARALELO/INTERMEDIÁRIO de 04 pinos.
This video is not correct. The light will be on when all the switches are in the same direction, or when the first two pairs are in the same direction and the other two pairs are in the same direction. Otherwise it will be off.
pullshit - you need - two three-way and two cross-connect switches - on one end of the swiches connect P(hase) - between the swiches connect corresponding wires - on the other end, connect the lamp-wire to connect to the consumer. - on the consumer lamp connect N(eutral) and the lamp-wire - it is never allowed to connect a P(hase) to al lamp. Phases are always connectet to the switch-connectors.
Saklar 3 & 4 hanya bisa utk matikan atau hidupkan lampu jika saklar 2 on atau ada aliran listriknya jika saklar 2 off/mati, maka saklar 3 & 4 tdk bisa hidupkan lampu.
This doesn't work. Any switch can turn the light off, but can only turn it on in certain conditions. It needs "crossover" or "intermediate" switches for the inner two. Alternatively, you can use "Quinetic" or equivalent type switches. Materials cost more, but labour and disruption WAY less. This is the future.
This Wiring Work or Not Work proof
ruclips.net/video/3WCYjeO7i6A/видео.html
not work for 4 switch
Doesn't work. You must use cross switch, between 2 two Way switches!
@@attilazabos846 yes, the solution is exactly what you wrote.
What type of switch?
@@gleentrajano9305 question for?
This will work but only if you only turn it off from one pair of switches. If it is off from the left pair, nothing you do with the right two switches will turn it on. Replacing the two middle switches with DPDT switchs that reverse the traveling wires will make it work from any location.
i agree
For those readers who don’t know, a DPDT switch for house light wiring in USA, is called a 4-way.
absolutely correct, instead of switches that make a permanent connection once pressed, they'd better use a door bell button, of course with the same look as any other normal switch, and a relais, then you can have up to dozens of (door bell button) switches.
@@renemeier9057 it is called télérupteur in france it works with a coil and push buttons dpdt switches are not allowed anymore that is according to norms what you have to install as soon as there are more than two switches controlling a light otherwise the set with two 3ways only that we call other wise (cause in fact they are only two-ways) are still in use I knew right away there was something wrong thanks for sharing : )
@@veidorje1681
Ceci n'est pas un telerupteur c'est un simple montage avec quatre commutateurs.
This wirig is totally wrong!!!
If the right side is switched off, the you cannot switch on the light on the left side! The middle two switches have to be X (4connectors) and not V (3 connectors)
----------
Wrong Connection, Misleading Video
If the first two two way switches are placed in OFF position (One On and Other one OFF) then phase will not pass to the last two switches, then how can you turn ON the bulb using the last two switches
Also the animation shown is wrong, the bulb should glow if the two switches are placed in either both in ON (downword)or both in OFF(upword), and the bulb should turn off if any one switch in placed in On(downword) and other in OFF(upword)
You are absolutely right
Yes you r right
Yes wrong
so tech me better please
@@ufomadutochukwu4694 please is a correct connection
The two center switches should be 4 way
ruclips.net/video/3WCYjeO7i6A/видео.html
This circuit don't work 100%...ok...no thank.
This looks like it will work to me, Marvin. Do you not think so?
@@wittydisplayname1761 No.
When interrupteur, 1 is open ,2 close ...no current go.
So,if you clic on 3 or 4 ..no work..no work.
For 3 and 4 , is work. 1 and 2 same position
If 1 and 2 no same position..3 ,4 don't work
@@pierrebreton1153 I think I see what you are saying, Pierre. I think if the light was on you could turn it off from any switch but if the light was off you could not necessarily turn it on from any switch because the circuit might be broken in 1 or 2 and nothing 3 or 4 does can change that…and visa versa.
Sangat simpel bermanfaat cover VErlita hader
You can control a bulb in so many location even 100 locations if you want to... provided the type of switches used are 4way switch...😊
Pas tout à fait.Aux extrémités il faut quand des inter.à 3 voies
@@Gilbert208 en France il y a une norme, 2 points d'allumage = va et vient, 3 points d'allumage = permutateur possible, à partir de 4 points d'allumage c'est télérupteurs. Aucune chance d'obtenir le consuel avec un bricolage comme ça qui en plus ne fonctionne pas. Les normes électriques US me font peur...
Actually, the two switches at the beginning and the end need to be three-way switches, all others, four-way switches
Nice sharing sir watching here sending full support
Thank you so much
Woooow
Very goooood
Thanks
Best video for RUclips
It doesn't work perfectly... if you change the state of 1st or 2nd switch, turning off the light, then the 3th or 4th switch can't control the lamp... In really, the circuit acts a AND logical function, where 1-2 switches are in series with 3-4 switches...
Faites nous un shema va et vient
Awesome! Interesting tip!
Thank You
Pero el salto a los otras llaves d combinación( par opuesto) no es posible si desde su complemento no la habilita. Pero igual está muy interesante el circuito, un abrazo desde Uruguay 🤜🏼🤛🏼
one lamp, four switch ?
impossible ?
iam groggi, labil ?
what's can ?
#ThumbDown !
Good this encourages us to carry on our project of making teaching learning materials by using waste plastics
ruclips.net/video/3jaEmRyrcUM/видео.html
Very good video editing
Thank you a beautiful comment
Your tips very very useful for every one. Thanks. God bless you...
Thank you so much
nice work
Thanks ❤️
The two middle switches must be intermediate switches for it to work with no problems.
ruclips.net/video/3WCYjeO7i6A/видео.html
They also make 4 way switches for this .
Thanks for sharing idol...☺ full support
Thank you
Although a great graphic, installing two pairs of 3-way switches connected as shown, will NOT work as shown. If there is no voltage coming from the first pair, there is nothing that can be done by changing either of the other pair of switches that will work because of no voltage at third or fourth switch.
Venho acompanhando as suas explicações, porém essa foi top a sua didática, parabéns.
Sí el par de llaves 1 y 2 no dejan encendida la lámpara, no es posible actuarla desde las llaves 3 y 4. Igualmente si la llaves 3 y 4 la dejan apagada, para las llaves 1 y 2.
Tôi cũng thấy vậy .
Good work bro
Thanks ❤️
So good
Неполноценная схема. Будет работать только при соблюдении определённых положений переключателей. Выключаться будет каким угодно переключателем, а вот включаться только из той пары, из которой выключали и которые связаны по двухпроводке (1и2 или 3и4).
согласен, тоже смотрел раза два, думал может что упустил, но нет. Не всегда есть возможность включить свет одним выключателем, а выключить другим, и наоборот выключить одним, а включить другим
@@otsy7947 перекрёстные и проходные помогают)а это ерунда какая т
Как охрененый электрик чуть не побежал проводку тянуть...спасибо парни))))
Nice graphics, but your circuitry is flawed. Only the outer switches can be 3 way. The center ones need to be 4 way in order for it to work properly. It's the sort of mistake a lot of non-electricians make.
si l'interrupteur 2 est sur "off" impossible d'allumer avec le 3 ou le 4
On peut brancher 3 interupteurs en va et vien mais il faut un interrupteur 4 voix et 2 inter 3 voix
Good video.
Thanks ❤️
WoW
Amazing
👍👍👍
Never have I see switch terminals like.
Só funciona parcialmente!!!
tem horas que não vai acender!!
Good
Thank you so much sir
Muito obrigado!! Essa ligação, eu não conhecia!! Valeu!!!!
Thank you
Mane, isso nao funciona , se desligar o segundo , para todos os demais.
ele tirou barato da cara dos otarios que acreditaram. Duvida? testa.
Pena que não funciona.
Very smart thank you
muito bom gostei obrigado professor por este vídio tão inportante
Thank you for comments
Professor? larga de ser mane, ele esta tirando barato da sua cara, isso nao funciona, se desligar o segundo , para os demais.
👌 Super
Muchas gracias por el circuito que no conocía.
Parabéns amigo estamos juntos
Thanks for sharing it with us
Thanks for watching
Essas nunca vi! pra mim é novidade mais uma que aprendi
Não funciona. Se qualquer um dos dois primeiros interruptores estiver desligado a energia não vai chegar no terceiro.
Por isso existe o interruptor PARALELO/INTERMEDIÁRIO de 04 pinos.
@@EddieMetal68 verdade eu? achei interessante
Até mostrei pro meu filho
Qualquer dia vó fazer num teste
@@valdecidepaula3709 nem precisa testar esse circuito aí, sou engenheiro eletricista e sei que não funciona. Interruptores intermediarios (4 pinos) são feitos pra isso, pois evitam esse problema que ocorre na ligação que o sujeito está espalhando por aí.
Sempre tem que haver 02 condutores entre os interruptores.
@@EddieMetal68 kkk não vó nem perde tempo bgd eu que achei que iria emconomiz o interruptor intermediário e caro
Mas valeu bgd
Sem o for way nunca vi.
Thanks for your useful information
Thank you
It doesn't work if switches 1 or 2 are set to OFF. Energy will never arrive to switch 3 and 4.
Good tutorial and it is easy to follow 👍
And now how to live with it?
Very nice bro
Soy Electricista Profesional , esta manera o ckto , no funcionará ya que en algún momento una llave quedará abierta y no encenderá de ningún otro punto . para esta instalación se necesita obligatoriamente dados de 4 vías.
It's 4-way AND gate, meaning this circuit will close only if all four switches are closed. But, since we can turn off this circuit just by opening only one circuit, it has to be AND
Данная схема неправильная работать будет частично
Good job
Thanks for watching sir
Good video !! Thanks !!
On such videos should teach people and not mislead
Nice sir i like it sir
Thank you
Thanks , it is correct connection
Thank you
the two middle switch should be double pole double throw (DPDT) switch for it to work
Thank you
Double pole, single through!
Muito bom nota 10 eu vou fazer aqui em casa
ruclips.net/video/3WCYjeO7i6A/видео.html
Não funciona esse circuito, se desligar o interruptor da esquerda, os da direita param de funcionar.. Furada.
First switch on and second switch off position, not working other switches.
this is wrong connection
This circuit don't work for all states. For example you cant turn on the lamp by one SW in left pairs if you turned it off by one SW in the right pairs. This never works properly.
die Schaltung funktioniert nicht. Aber schön gezeichnet.
Not possible ..... Not working...
Please check the wiring is 100% working
@@itselectrical if first two switches not passing current then how can anyone operate last two to turn off/on the bulb.?
off-course possible bro........... here you must use two-way switch, not one way
@@BikashRoy-yn3zo think again bro...
ruclips.net/video/aQhoPwbRH5M/видео.html
From figure given, let us say all switches are on ( coz all switches are upper pressed), so the bulb is lighted. Let us label first the four switches namely from the left, A, B, C and D. What will happen then, if:
Leftmost switch (A) is swicth off (lower pressed). Then, the connection or continuity line of switches A and B is disconnected. Then the bulb lights off.
With the above condition (A is disconnected with B, coz A is lower pressed and B is upper pressed), What if You're located near switches C and D, how can you turn on the bulb/light by switching C or D?
Switches group A & B will work just by themselves, as well as switches group C & D will work just by themselves. If both groups are connected to each other, ie, as what shown in the figure, the connection of the two groups' line continuity cannot be proven or established to be always connected.
Se acontecer isso mesmo eu te dou parabéns. Estou testando na prática agora. Não acredito ainda perdão.
Ещё не хватает три розетки и два рубильника)
Merci bcp ❤
Thank you 🙏🙏🙏
Circuito errato
Se si vuole accendere e spengere con qualsiasi combinazione bisogna inserire degli invertitori su 3 e 4.
Point, and travelers.
The points goes two ways. The point terminal on the closest to the light
Very nice
Thanks
If only it worked. Viewers should be warned not to expect this to work.
Good👍
Thanks Sir
Good Nice Sir
Thank you
شكرا!100%ثانكس!
Those were always fun with one wire in wrong place.
ruclips.net/video/3WCYjeO7i6A/видео.html
Muito legal, perfeito. Faru.....
Não funciona. Se qualquer um dos dois primeiros interruptores estiver desligado a energia não vai chegar no terceiro.
Por isso existe o interruptor PARALELO/INTERMEDIÁRIO de 04 pinos.
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍tres bien
AS per your circuit your bulb is burning 24×7 without SWITCHINGON,
Show ! fiquei todo bôbo quando instalei o tree way, imagina 4 ???
Não funciona. Se qualquer um dos dois primeiros interruptores estiver desligado a energia não vai chegar no terceiro.
Por isso existe o interruptor PARALELO/INTERMEDIÁRIO de 04 pinos.
@@EddieMetal68 É sério isso que vc falou ?
@@branddo sim, é sério. Sou engenheiro eletricista!
Para esse circuito funcionar precisa usar 02 interruptores intermediarios (4 way, intermediários ou inversores, depende da região o nome muda). E sempre usar um par de fios , que é onde esse circuito fracassa, pois se cortar a energia se um lado, ainda podemos ligar para o outro lado!
show??? Cara , ele esta tirando um barato da cara dos otarios que acreditam, se desligar o segundo , para os demais , Nao funciona.
@@saureano Não se trata de otários, quem é leigo acredita, eu sei fazer o three way mas não sou "expert" como vc...
Brilliant connection and guidance.
Thanks Raj Shah
Spoiler alert: It doesn’t work in the other video either.
From what country do you hail? This diagram works but is quite different from the way it would be done in the states.
Good, very good
Thank you
Não funciona. Se qualquer um dos dois primeiros interruptores estiver desligado a energia não vai chegar no terceiro.
Por isso existe o interruptor PARALELO/INTERMEDIÁRIO de 04 pinos.
Gostei se der certo não precisar colocar intermediário entre os paralelo vou fazer o teste depois
Nem precisa testar , ele esta tirando barato , se desligar o segundo , para os demais. Da deslike para este trouxa
Without music teacher please. Thanks
Deviatore, invertitore, invertitore, deviatore 👍
Ok felicitări
This video is not correct. The light will be on when all the switches are in the same direction, or when the first two pairs are in the same direction and the other two pairs are in the same direction. Otherwise it will be off.
ruclips.net/video/aQhoPwbRH5M/видео.html
Right connection please watching this video
pullshit - you need - two three-way and two cross-connect switches - on one end of the swiches connect P(hase) - between the swiches connect corresponding wires - on the other end, connect the lamp-wire to connect to the consumer. - on the consumer lamp connect N(eutral) and the lamp-wire - it is never allowed to connect a P(hase) to al lamp. Phases are always connectet to the switch-connectors.
Sorry sir instead using 4pcs of 3way swtch why dont you use 2 4way switch. Thank you
Khi gỏi vẽ máy tính mà không được học hành môn vật lý
palpak
Thanks for comments
Hi guys post ko lang din po ung yt chanel ko kba pwd nyo din pano orin
Este circuito não funciona
Para mais interruptores é necessário usar interruptor intermediário
✋
Saklar 3 & 4 hanya bisa utk matikan atau hidupkan lampu jika saklar 2 on atau ada aliran listriknya jika saklar 2 off/mati, maka saklar 3 & 4 tdk bisa hidupkan lampu.
ruclips.net/video/3WCYjeO7i6A/видео.html
This doesn't work. Any switch can turn the light off, but can only turn it on in certain conditions.
It needs "crossover" or "intermediate" switches for the inner two.
Alternatively, you can use "Quinetic" or equivalent type switches. Materials cost more, but labour and disruption WAY less. This is the future.
Super
Thank you
😉
This will not work. If A is up and B is down, you can't turn it on with C or D.
Yes, the conversion key has this feature, even more than this feature , Another key also has
Thanks
🙏👍