This instructions in this video worked for me ... but the instructions on the inside lid of the keypad did NOT work for me. Glad I found this! Thanks!!!!!!
Thanks so much! Your instructions were the only ones correct and clear after wasting time watching other videos that did not work. Thank you, thank you!
As far as I can see, my LiftMaster opener doesn’t have a learn button. There is a display with a menu, but no learn option. Looks totally different from yours
Thank you so much, I kept trying to set it up from the motor because of other tutorials on RUclips. Having it set from the door opener by the garage door made it so much easier thanks to you!
Just curious in some other videos it states to press the learn button on the ceiling garage door opener unit while in your video you show using the wall mount. What’s the difference? Also will creating a new pin have any impact on the ability to use my vehicle’s built in garage door opener that is already linked? Thx in advance!
Todd, I have a chamberlain, same key pad exactly. All of my buttons work. I replaced the battery. It was dead. Now when trying to program it as the old number did not work, I push the learn button on my motor assy housing, push in a new code and hold the enter key down, waiting for my lights to flash, but nothing happens. I did not check the enter button to see if the key pad light up, but I will do that now, but assuming all buttons work, what can I do to get it going. I cannot afford a new key pad right now. I know they are just $30, but I have been out of work for 4 years. Just trying to get this working. I was a copier tech for 14 years, so even if I need to work on the keypad, I can do it. Thanks for any help you can give me.
@connerdavis3333 i removed all codes by pushing and holding the learn button on the opener ( for about 6 seconds) until the indicator light next to it turns off. Then I put the new code in the key pad . That worked. Of course I had to re sync all the garage door remotes as well.
This was so incredibly helpful! I somehow undid the previous owners code thinking I could change it to my preference. I kept trying to reset it from the lift itself and that did not work clearly. The solution was a lot simpler than I could have imagined and was able to do it in -26 Celsius
What do you try if that does not work. The keypad is from 2005 but I have replaced the main unit witha new Liftmaster. The remotes work fine but the keypad just flashes no matter what I try. The 9v battery is good and it worked long ago so could it be wired?
installed a chamberlain 940ev wireless opener it works fine with the 4 digit code to open the door however just using the enter button to close the door does not work the unit is a craftsman opener thanks for any help
Hey Todd. Garage door keypad in my house is not accepting the pin code. I am certain that I am entering the correct code, and I followed your awesome instructions (so clear and helpful) about how to check the battery and keypad. I replaced the battery even though the old one was working well and there seems like all buttons are working fine on the keypad. My garage is detached so I can't access it from inside the house. Any suggestions what I should do?
if i accidently paired with neighbour's garage remote control while I was changing the passcode on my garage keypad, right now my.neighbour can open garage.door, what.should i do?
My door is closed and I have lost my garage door opener. I just replaced the batteries in my keypad and now the code doesn't work. I am stuck! Any advice?
Nothing is working on mine. The motor lights never blink for me, what am I doing wrong? Do I hit the learn button on the motor or the opener button on the wall with the flap? This thing is frustrating to say the least.
Sadly this doesn’t work. Double pressing the learn button doesn’t make the yellow light to flash. And pressing long on enter does not make something click….
Two nights ago tried to use the keypad and didn't open just blinking, tried using the remote and also weren't responding. Switched out batteries on the keypad . Eventually go in the house with a key. Reprogrammed the keypad and the remotes. Ensured multiple times they were programmed and working properly. Last night at 3am a family member tried using the keypad and went back not working and only was blinking. I went outside myself at that time and both keypad and remotes stopped working. I have the My Q app which allowed me to open and close no problem. However the keypad and remotes stopped working. Anyone have any idea or trouble shooting I can figure out? Thanks
Thank you Sir!! After 20 min of contemplating my existence I was lucky enough to find your video. I was a real man again in seconds lol 🙏🏻👊🏻
"Contemplating my existence"...oh, how I can relate!
We moved into a new place and previous owners did not leave us a code. Tried your directions and it worked perfectly. Thank you!
Your directions worked! For someone over 60 I thought this was impossible. But with your directions I got my keypad code changed!
This instructions in this video worked for me ... but the instructions on the inside lid of the keypad did NOT work for me. Glad I found this! Thanks!!!!!!
Same!
You're the best step-by-step guy I've on youtube leaning. Thank you, sir.
This is the only video I found that actually answered my question
Thanks so much! Your instructions were the only ones correct and clear after wasting time watching other videos that did not work. Thank you, thank you!
After viewing your 2:34 minute video, it took me less than 1 minute to accomplish the task.👍🏾……thank you!
Awesome! Thank You! I watched a dozen other videos that were incorrect and over complicated. Only yours worked. Best Wishes my friend!
As far as I can see, my LiftMaster opener doesn’t have a learn button. There is a display with a menu, but no learn option. Looks totally different from yours
Same with mine. I have the elite series and can't find one for it.
I don’t have one either 👎🏻
We don’t have a learn button?
U have to climb up to the lift master in the garage.. the learn button is to the back
Thank you so much, I kept trying to set it up from the motor because of other tutorials on RUclips. Having it set from the door opener by the garage door made it so much easier thanks to you!
Hi Sean, Thanks for watching and the feedback! I am glad this video was helpful and made changing the pin code easier!
Thank you for giving a simple, clear solution.
After 5 different videos, this was the one that worked!!!
Very helpful and simple to learn, great job. Appreciate your time 👍
I have added the new code, but how do I get it to stop using a previous code? I haven’t been able to get it to not respond to the previous code
i have the same problem the old code still works
Clear instructions and easy to follow. And NO LADDER involved which is great for us geezers. Thanks a ton!
Thanks A Billion! I no longer have to steal my moms Garage door clip when I ride my bike!
Great job mate. Helped me here. Thanks!
ty - just perfect. looked thru so much online - but this one helped and fixed it.
Thanks for educating me on how change code
Thanks worked like a charm 😊
great tutorial and so simple. Thanks
Worked as you advertised! Thank you.
Looks easy, will try it in a few minutes. Thanks!
thank you very very much, brand new home owner and did not want to call a company
wow, no more climbing up a ladder and fighting to remove the light cover to press the yellow button. A done so easy. So grateful for this video!
Thank you for making this video
I did it today! Good video!
Just curious in some other videos it states to press the learn button on the ceiling garage door opener unit while in your video you show using the wall mount. What’s the difference? Also will creating a new pin have any impact on the ability to use my vehicle’s built in garage door opener that is already linked? Thx in advance!
Got it thanks! It was pushing Learn twice, then code, then hold down Enter. Whew. Thanks!
Worked great thanks!
I went with the ladder to the top looking for the learn button, couldn't find it, what an idiot, thank you so much for this video
Very helpful. Thank you.
Short and sweet 🔥🤙
It works easily. Thanks!
Awesome, thx. Worked!
Great information thank you very much
I seem to have a different wall control as there doesn’t seem to be a cover that lifts up?
This is awesome ! Thank you so much 😊
Thank you for such clear easy instructions
Worked perfectly!
Thank you Todd. I just changed the code on my Liftmaster Keyless Entry due to worn key pads.
Thanks for watching! I am glad the video helped!
Greatly appreciated
Great!!!! Works😁
Thank you!
Worked. Thank you!
You da MAN Todd..thanks!
Todd, I have a chamberlain, same key pad exactly. All of my buttons work. I replaced the battery. It was dead. Now when trying to program it as the old number did not work, I push the learn button on my motor assy housing, push in a new code and hold the enter key down, waiting for my lights to flash, but nothing happens. I did not check the enter button to see if the key pad light up, but I will do that now, but assuming all buttons work, what can I do to get it going. I cannot afford a new key pad right now. I know they are just $30, but I have been out of work for 4 years. Just trying to get this working. I was a copier tech for 14 years, so even if I need to work on the keypad, I can do it. Thanks for any help you can give me.
Hi! My old code still works. Can you please show us how to delete old codes?
Same here. Help?
Thank you very helpful
Great. Now I have 2 codes to open my garage. The old one and the new one.
Me too
@connerdavis3333 i removed all codes by pushing and holding the learn button on the opener ( for about 6 seconds) until the indicator light next to it turns off. Then I put the new code in the key pad . That worked. Of course I had to re sync all the garage door remotes as well.
@@floridajogi8175i will go try. Tnks. How do I resync the remotes pls?
THANK YOU! 🎉🎉🎉
thank you, the other clips made it hard to change code
great , thank you
Great contribution to society 😀. Thank you!
This was so incredibly helpful! I somehow undid the previous owners code thinking I could change it to my preference. I kept trying to reset it from the lift itself and that did not work clearly. The solution was a lot simpler than I could have imagined and was able to do it in -26 Celsius
Awesome ! It was really easy. Thank you
Anyone that still has any questions is a bozo, thank you for a very clear easy to follow video
Do I need to press the learn or lock button after I set my new code?
Will this remove old codes?
Will I be able to use my remote opener?
Life saver 🔥
Very easy to follow video. Worked like a charm! Thank you!
😅😅so easier and verry clearly
What do you try if that does not work. The keypad is from 2005 but I have replaced the main unit witha new Liftmaster. The remotes work fine but the keypad just flashes no matter what I try. The 9v battery is good and it worked long ago so could it be wired?
Thank you so much. Very helped me. 👍🏻👍🏻
Thanks for watching, I am glad the video helped!
installed a chamberlain 940ev wireless opener it works fine with the 4 digit code to open the door however just using the enter button to close the door does not work the unit is a craftsman opener thanks for any help
Do I need to do anything with remotes or will they still work?
Does anyone know if it'll reset or "unlearn" other remotes?
And No if you have the exact system shown it will NOT change the remote, only the keypad. This is literally a 20 second job. Thanks for this video
Very useful .
Thank you kindly!
Thank you
Are lifemaster garage openers universal
thanks!
Possible to add more than 1 code?
👍 So easy thank you 😊
Thanks for watching!
Thanks Todd
Thank you Todd!! Saved us money
Thanks, you helped me out!
Thanks for watching!
Thanks
Hey Todd. Garage door keypad in my house is not accepting the pin code. I am certain that I am entering the correct code, and I followed your awesome instructions (so clear and helpful) about how to check the battery and keypad. I replaced the battery even though the old one was working well and there seems like all buttons are working fine on the keypad. My garage is detached so I can't access it from inside the house. Any suggestions what I should do?
Thank you very much. They made it so hard in other videos that if I couldn’t believe what you did. 😂
Hi there,
When I enter the new code and hit enter nothing happens? Maybe I need a new keypad.
if i accidently paired with neighbour's garage remote control while I was changing the passcode on my garage keypad, right now my.neighbour can open garage.door, what.should i do?
I changed the code but the old code works too. How do i fix that??
I am also having this problem!
Same issue too. Old one still works. Any ideas how to fix that?
@@21Carlos237 Isn't this shit infuriating?!
What if the key pad is to a swing gate, and there is no learn button or light to blink. ?
My door is closed and I have lost my garage door opener. I just replaced the batteries in my keypad and now the code doesn't work. I am stuck! Any advice?
My light just blinks twice when I try and shut 😢 i have walked through your steps ten times 😢😢
Nothing is working on mine. The motor lights never blink for me, what am I doing wrong? Do I hit the learn button on the motor or the opener button on the wall with the flap? This thing is frustrating to say the least.
Thanks this video made this so simple it took me three years to get the courage to figure out how to do it 😂
Where can I find written instructions?
Just bought a replacement thinking what was the problem but it still doesn’t work with the new one. It’s not detecting the key pad.
Maybe my motor is defective 🤷♂️ 😭
Pressing "Enter" by itself will close the garage. Don't get fooled by that feature.
Great
Sadly this doesn’t work. Double pressing the learn button doesn’t make the yellow light to flash. And pressing long on enter does not make something click….
Same issue
It makes my yellow light flash, but when I put in a code and hold enter it doesn't work.
It works but the old pin code still working too
My Lift Master keypad doesn't have an enter key. Just star and pound key. How do I proceed from here, if anyone can help?
Two nights ago tried to use the keypad and didn't open just blinking, tried using the remote and also weren't responding. Switched out batteries on the keypad . Eventually go in the house with a key. Reprogrammed the keypad and the remotes. Ensured multiple times they were programmed and working properly. Last night at 3am a family member tried using the keypad and went back not working and only was blinking. I went outside myself at that time and both keypad and remotes stopped working. I have the My Q app which allowed me to open and close no problem. However the keypad and remotes stopped working. Anyone have any idea or trouble shooting I can figure out? Thanks
My LiftMaster said program, and then, when you look at the screen, it says to press program again, and than set new code