FZ25 | How To Replace Drive Chain Sprocket | Life of Pal
HTML-код
- Опубликовано: 30 июл 2020
- Explain steps on how you can replace the drive chain sprocket at home on FZ25. Its a very easy job with few tools you can do it easily. You also need to remove both side panels. I didn't covered in this video as its very easy.
Alternate Torque Wrench (not tried buy at your own will)
amzn.to/3hVMppE
Video on adjusting chain slack • Chain Slack & Wheel Al...
Tools you need
08mm 1/4inch drive socket
10mm 1/4inch drive socket
30mm 1/2inch drive socket
22mm 1/2inch drive socket
17mm 1/2inch drive socket
17mm ring spanner
12mm ring spanner
10mm ring spanner
2*12mm open end spanner
Screw Driver
Music By: / neutrin05
********************************************
After receiving lots of wonderful amazing comments on my uniqueness way of presenting content. I can confidently say this is something you don’t want to miss. So, I urge you to watch more videos and then decide to subscribe. / lifeofpal
*********************************************
SOCIAL AROUND INTERNET
Facebook - / gurpal.1911
Insta - / gurpal_ent
*********************************************
BIKE MAINTENANCE STUFF & ACCESSORIES
Motul 7100 10w40: amzn.to/2oKATqX
Petrol Additive: amzn.to/33RXGDK
Pressure Gauge: amzn.to/3kzbHw5
Shoe Protector: amzn.to/3iwrGcl
Puncture Kit: amzn.to/3kDKp7F
Key Chain: amzn.to/2XUACAx
Balaclava: amzn.to/2LLEPBz
WD40: amzn.to/3kB0bQT
CHAIN CLEAN
Motul Clean & Lube: amzn.to/2AmePsb
Rubber Hand Gloves: amzn.to/2v0AJw2
Chain Clean Brush: amzn.to/2mQsCNZ
BIKE WASH STUFF
Shampoo: amzn.to/2LxzC0V
Soft Brush: amzn.to/31MeglZ
Spray Pump: amzn.to/3kC3RSn
Bike Wash Sponge: amzn.to/2LLAej3
Micro Fiber (340): amzn.to/2XGy2fm
POLISH STUFF
Wax: amzn.to/2XSCVUW
For Plastic: amzn.to/2FhXa7Z
Tyre Polish: amzn.to/3iup6np
Applicator: amzn.to/2XRHONW
Micro Fiber (800): amzn.to/2FbgXWp
*********************************************
MY RIDING GEARS
SOL 68S | Rynox Tornado Pro | Rynox Advento | Cramster TRG2 | Scoyco MC20
VLOG GEARS
Hero GoPro 5 | YI 4K | SJCAM 6 Legend
Microphone Rode SmartLav+
Samsung Evo+ 128GB
*********************************************
Links above are affiliate links - which means I receive a percentage of the revenue made from purchasing products through this link without you paying anything extra.
*********************************************
Note: The owner of this channel shares ideas and experience of his own. All DIY videos on this channel are for learning purposes only. The owner of this channel is not liable for any damage, financial loss or injury resulting from not following the correct instructions and due diligence. The viewer realizes this and accepts full responsibility/liability of his/her own actions. 
Авто/Мото
Hello Pal Family,
Many of you were waiting for this, its up today. You also need to remove side panels and sprocket cover which is not covered in the video as its easy. Already shown in some of my videos. Let me know what you think of this. If its worth, appreciate my work by giving thumps up or leave a feedback. Thank you. God bless you.
sir, what is the tyere you use . In this video
Bro no one give this much information i have own this beast... just changed it at showroom thnks nice video
Good information bro.... Today i adjust my fz25 chain as per your video
Fantastic bhai. Mazaa aa gaya! Yeh maannaa padega ki 3-4 bar dekhe hi ise practically kar paunga. Bahut badhiya detail me tha, achcha laga!
Thank you Santosh
I was afraid to do the job.. but u gave me the confidence 😂
Excellent job...
Very useful. ..
But one thing we need to care about while adjusting chain slackness is be care to matching the direction of moving chain. It must be in a straight line for both chain wheels .There is some marking lines on both side of swing arm to adjust the slackness...
Thanks..
You are champion of DIY.
Complex simplified as always. 👍🤝
Nice Educational DIY video. It will help a lot.
What to do if chain rubber guard is worn out and not available at SC. What DIY you recommend?
WOW! I will try this with my ZMR. Hope I will be able to re-fit everything.
Hope 😅😅
Great work keep on doing good things 👍🏻
bro love your effort
need more content
Thanks, very informational video as usual.
This can be a good time to lube the swingarm bearings.
For the front sprocket, I had to use an extension for my ratchet, plus my friend pushed down on the back on the bike. I had to then use my leg to push on the spanner to loosen the sprocket bolt 😅.
For the chain we didn't want to go through removing the swingarm, so we used a master link to get it done. It's still holding up fine 15000kms later.
Waoo.....Great job. Thanks the Video.
is there enough space to slide rod or something in the chain? I am not being able to relate what you are saying
excellent man keepit up.... really excellent
Can I convert chain drive to belt drive in fz25?
You are extremely superb bro.. you are sharing knowledge which will save good amount of money by diy without visiting showroom.. labour charge at showroom rs830 for fz25.
Yeah you can transfer me those 😅
@@LifeofPal next time i will do bro.. today i spent 3800 for my fz25 service, nothing new got, gen service and battery and airfilter only.😭😭
Clean and neat 👍
keep going bro!
Nice video, my most awaited one
Sorry
@@LifeofPal pls don't say sorry, your work is very good, keep sharing videos like this.
Hey Gurpal i have done the same on my fz25 after 18000 km' i think it costed me in total around 6000rs (basic 5th servicing included)......
Question- I removed number plate bulb wire (5 W) from rear fender and connected a DC mobile charger (Robotouch Rideon) in the bullet connectors of stock wire (in +/- wires). Charger worked fine for a while and suddenly electric current from instrument was gone. No electricity while turning on ignition. Found that 15A main fuse was blown. WHY it happened? Connections were right still fuse blown. Why?
Short circuit or overload
Can you please make a video for swing arm bushing?
Mine fz25 bushings are worn out so.
I have that in my list. Will do that this month.
@@LifeofPal thank you 🙏🏻
1. Why not Aluminum sprocket?
2. Can I Install 150/70 tyre in stock FZ25 alloy?
3. How do you dispose engine oil when you change it?
4. what will you do with old parts? like how do you recycle it or dispose it?
5. Rust has developed on my handlebar and forks(due to rain), Is there any way I can get rid of it?
1. Aluminum is weak relatively iron or alloy.
2. I have also fz 25 abs.. but no idea
3. Go and ask ur nearby local mechanic shop for used engine oil collector. Fr example in my area delhi, east zone. They're taking 15-20 rs per litre.
4. Old parts u can sell at junk part @ 30 rs per kg(rate in my area).
5. For rusting, u can get spray from amazon or flipkart by typing rusting spray or else vist near yamaha service centre n ask yamalube rusting spray.. it might b costlier comparatively the other company products available on amazon or flipkart..
Hope it helps... Coz m doing the same... Cheers.. 👍
Please upload a video on how to replace fz 25 bs4 edition's high beam LED.
Its sealed not possible until some jugaad is done if possible
How do you get the troque specs of fz 25? ... I have look every on the internet. Plz reply
It comes from a secret place 😜🤐
Plz I need it for my fz 25.. Help me here
Great work mate 👌
Am facing accelerator tightness. Tried cleaning, lubing and even replaced new cables. Is there any solution for it or need to live with it. Looking forward for your feedback.TIA
Thats needs to be check unable to help. You can try loosing throttle body screw to see if it is free up a bit it will give you some clue.
@@LifeofPal Thanks 🙌
what wheel are you using for rear?
Ralco speed blaster
Hello Sir
Good Morning
Which engine oil your are using..Yamalube or Motul..
{2service done}
Yamaha fz25 2019 special edition owner....
I was thinking to upgrade engine oil
Motul 7100 10w50...
I am using veedol which no one does
Waat about sprocket bearing?
Can u plz tell me the price of
Air filter
Oil filter
Chain sprocket
Throttle cable
Clutch cable
Spark plug
Throttle body cleaning charges
Fuel injector cleaning charges
Handle bearing greasing
Over all labour charges
Great video and quite informative one. I have a doubt though. Isn't there any master link to remove the chain ? I mean you can remove the master link and the chain will open from there, you would not need to open the Swingarm in that case. Just asking this as every chain has a master link. Also, the swingarm needs to tightened with a specific torque I guess. Correct me if I am wrong.
There is no master link on this chain.
Exactly same issue in my fzs. Can't figure out the issue. Also my bike wobble while turning in slow speed also.
Yamaha's "original" chain sprocket is of Rolon brand. Its costs around 2000 in authorised service centre. Same thing you will get outside for 1500rs.
I asked to rolon dealer before buying. I told him number of teeth and links but Rolon currently not supplying that outside.
Sir .. aapke channel me fz25 hazard light ka video nhi milrha!
ruclips.net/video/qNlO9DSDAZg/видео.html
What is the pitch diameter of rear sprocket of fz25?
Dont know bro
Where did you bought chain sprocket
Service center
whats your tyre size rear ?
140-70
Agr front sprocket kharab hai to kya poora chain set badlna pdega ??
Ya sirf front sprocket milta hai market mai ??
Service center me milti hai front sprocket pata karo
What type of back tier ?
Ralco speed blaster
11:28 when I went to change my Fz25's Chain drive the mechanic told me this axle is a little damaged, if I change it bike will not have any vibration. My bike was at 20500km , He showed me how the tire and the swing arm is shaking a little bit, I think he fooled me because when I agreed he took out the axle nott from his own drawer and told me he will not include it in the job card. So my question is what about your bike is the Axle nott ok in your case?
Axel doesn't get damage by its own until met with an accident.
Wheel rotate in a bearing. So the play will be due to bearings not axel. New axel is expensive. He will not give it for free. Yes he fooled.
@@LifeofPal it was not free paid 650 for that but din't included in the receipt
Its definitely doesn't cost 650. Its around 150-180 as i remember
@@LifeofPal it was written on the packet 560 and two ring ring which cost 160 somethin i forgot.
Hi Bro, loved the video. I have a doubt, i recently changed my MT-15's chain and sprocket set to Rolon. One peculiar thing i noticed is that rear sprocket wobbles left to right when viewed from rear i.e lateral movement. Can you just run your bike on main stand and view from the rear if you have the same issue !? This is an issue faced on many bikes including litre class high end bikes. Did a lot of google and din't come accross and concrete solution, some say it could be because of the Cush Drive(The rubber grommets inside the hub). A R1 owner from US had the same problem and he changed literally every part that could lead to the issue i.e the hubs, cush drives, axle bolt,swing arm, sprockets and even the entire wheel set(alloy wheels) but it never went away ! So plz just check issue on your bike & revert back. :) I will share the link to the R1 thread where they have discussed and uploaded the video aswell, do check out to know exactly what the problem is.
www.r1-forum.com/threads/how-much-sprocket-wobble-is-too-much.599249/?__cf_chl_captcha_tk__=c1deb84ea095a403f0dcbcc8180718daca9a260e-1612373020-0-Abwgk4L5i79V2-uEf09BsENqGcIQ7SrPUL7n7ekMXhH1Y-lrdWF9HF-WRV7CaTy_eE4ROf6GrMQBKDfKuHTjStER_MWvM1DrmPPwvPQvPiNZa5JDKsGK5M8VMrqqPMTMIKkq9wDo6DtIt62McbIAEU3x-SJyGiTsTXahrbimhoYtDEzPedPTkLV628KVKciyH6u_yUiZE6PsPs7RQwvmC_XbxQj4izo65L_g3_QFjsijPQhCUQuMBhag342-22X6lwX32NqUC0m9uVYFcsjeIQCouFUrD-fOLJOhEAtP1Fa_dvrOYYmK9zJmSSI5IdK4EETT-qGJwcp0Es2CxN5gUdj0e80OJi1buxMsW4VKPRP1xoSC0Z36ZtpGUpSsR2K_SnsLvcMBDzRGDHKw89jHrdWRDI9RBRIu2IcHdZfn8owu8q-ao2vOUZGdFK2Ti8snTjppl5L-WwoFBdgoTH_gi40PFZsJpaouo0zPV2ipgWHVcG6hI4MqERrXUVYC1pJjN2PG92_o2-X7H5HNSkSuFMDuxE618Pe4DJtFagS6bjT9qh-NRFwmo_nOZj3yuo14qOS4uM71DdY0m8OCpc3HCpGEhs81BIKVG9tdAKwOIBfsuuaXfzpG8jQk7okNgc7lGc9cJOLH2jEOK55lbAhAJFs
there will be some slight movement in every bike you cant make it perfect. these are not superbikes made in limited piece with absolute perfection. we have to accept the fact these are high production cheap bike. so when you focus more on production at less cost quality will be compromise but we expect too much out of it. If movement is too much then get it checked otherwise ignore as chain sprocket does contain some play so no worry
@@LifeofPal Cool,thanks for the reply bro 👍
Can i remove chain with cutting
Try. How will fit a new chain then
Bro, can u tell me that how long last your old chain & sprockets?
25000-27000
My fzs v3 around 18k+ going on. But there is irritating noise in the rear side chain like "karuk muruk" even I maintain my chain clean with lube every 500km. Can u guess what may be the reason for this?
Send me the teeth pic at 9654242269
@@LifeofPal ok bro
Damn good video broda
Thanks bro
Motogenesis, I follow your channel too, can you please tell me the pitch diameter of rear sprocket of fz25? I want to buy a 44T sprocket like you did..
@@eddieroyal2020 hi man. I dint get into the details of it I just left it up to sparrow tech. They did the whole thing and it fit like a glove
@@MOTOGENESIS_IND
How do I get in touch with them?
bro... what chain sprocket brand you currently replaced ?
Original from service center.
thanks bro...
Original from service centre is of Rolon. Its costs 2000 rs . Same thing you will get outside for 1500. 500 extra you pay for the yamaha packing.
oh okay okay bro 👍
where can I get only front sproket for my fz25, got nowhere .............. plz help
Company stopped selling separately
Thank u pal... can you provide me any link to buy it...
No bro not available anywhere
Price?
Do fz 25 have endless chains to compulsorily remove centre axel to replace chainkit ?
Yes
@@LifeofPal bro i have fzs v2 and its chain set was recently changed from yamaha service centre but there's this rolling noise coming from front sprocket that was not there in the old chain set and it's so much irritating that anyone can sense it if they ride my bike and i have literally done everything i could to solve it but it's of no use so do u have any idea what it might be ?
I have a query bro please answer me...!
What
kiya price hai chain spocket ka?
2100 k around
Kitne Km me chain set chamge krna chahiye fz25 ka??
22k-26k range me kharab ho jata hai tab
Bhaiya or clutch plate fz25 ka hi??
Bro, Why did you remove swing arm to replace chain /sprocket . i mean, we can remove the chain by removing the chain lock right with a nose plier
There is no lock
@@LifeofPal hmmm it's a big headache to remove so much for chain sprocket replacement. Bad choice of chain sprocket by yamaha
What is the price for chain Sprocket bro?? Few guys are saying it is 8k
I believe the max price should be 2500
Around 2150
Back tier model
Price of chain spocket???
2118
Oy Gurpal ji, oy chak de phate
Jo bole so nihal....
At which price u got from service center..?
I bought long back for 2050 now its increased a bit
@@LifeofPal i have also fz 25 abs, the way u describe n present.. its above all... Mind blowing, i subscribe so many channel, but u explain simple, crisp, and attractive... Informative.. god bless, keep growing man..
Thank you Varun for sincere appreciation. Thank you
I would like to give u advice, as u live in delhi n u need to buy some costlier product for FZ 25. Visit karol bagh, there is shop name Jain yamaha, official shop by yamaha and each n evry part original with 20-30% cheaper thn workshop. I had previous bike YAMAHA LIBERO, the reg expires then i purchased fz 25 abs. But m purchasing evrything from there including engine oil.. since 5 years...
💯% genuine...
Hope it helps..
@@VarunKumar-mg5sz Google map link, plz. And full name of the shop?
*Gurpal Singh* 💚💚💚💚💚💚💚💚💚
Bhai. I am mentioning it not for offending you. Its not Wrench while pronouncing. Its rench ('W' is silent)
Thank you and keep up the good job.
Oh thank you for correcting me. I am always open for feedback.
@@LifeofPal lots of love to u bro, by the way how's ralco as compare to other brands, wet grip and puncture resistance?
@@dineshojha033 thank you for you love. I haven't used other brands but ralco is better than stock. Haven't punctured since fitted. Performed well for me on its price.
@@LifeofPal ok, great , one more thing can we try R15 sprocket (teeth diff) on our FZ25 ? Or make a video on that if possible, installation test..
@@dineshojha033 should be fittable need to check but service center dont sell only sprocket
Hi dude, you have done a tiresome work with videoing and describing. You are really great awesome.
Please bro make in Hindi 😘
First like
Thanks bro. Here i gave u first heart.
Please speak the Hindi sir
Ye sala yamaha fzs me kitne baar v chain socket change kro har baar 4to5000km ke Baad hi kat kat ki awaz ani start ho jati h. I'm fed up why I bought fzs. Better go for hero or Honda bajaj
I have sent u a message in ur messenger. Plz respond
What messenger. Didn't got any. Ask here it will also help others