How to make the disc sander SHAFT with bearings
HTML-код
- Опубликовано: 8 сен 2024
- In this video I make the driving shaft I will use to build a homemade disc sander. After the problems I had making the disc for the disc sander in my last video, now I decided I should make a shaft with bearings, so it will be easier to rectify the disc and to protect the drill from vibrations.
Watch here my problems trying to rectify a disc connected directly to the drill chuck: • Problems trying to mak...
More on this shaft with bearings in my woodworking and DIY blog: enredandonogar...
Omg this is the prefect solution for fixing my belt sander. Thanks for the idea
I like your videos, because you use basic tools and show your mistakes!
isakwatz11 l
isakwatz11 g b
isakwatz11 qTajči
katlanabilir sineklik nasıl yapılır
That looks like a suitable arrangement for many other kinds of DIY woodworking powertools such as a lathe, belt sander, or small circular saw. You managed to find just the right collection of pipes, threaded rod, washers and bearings to fit perfectly; well done!! Now you'll inspire hundreds of people to hunt in hardware shops and second-hand dealers to get similar pieces.
dav snow 0
dav snow. Congratulations by the adequate comments about the amazing video. I do mine words yours.
Inasio Reyes Vasquez ijiu
instablaster
Thanks for uploading.. You gave me an idea for my project!!
Thank you for sharing. I was going to purchase an electric motor (£100) to use in making my own disc sander, then I saw your videos. Now I intend to use an electric drill instead.
Thanks for this video, gives me an idea of how to make sure my bearings line up when building something!
I like your videos , you explain very easy and slowly .you make great job. thank you
very good idea
NIce tip for stabilizing the shaft.
Myself , like you enjoy making something that is useful even tho it might cost more in the long run... Thanks for sharing and do not read the stupid peoples remarks. They just do not know any better.
This is a great idea. Afkharisto
Very nice. It's a little hard to find these parts for me, so I used a old bicycle wheel hub instead.
Smart idea !
You seemed to have skipped a few things, you described the bearing set up but not the way you used it
very cool idea and nicely done, u can do the same only make the mount for the bearing with wood on your drill press, a forstner bit or a holesaw( for a layered mount) will give u a pretty perallel holes for the bearings
u could of also cut the pipes on your jigsaw table with a fence maybe more precisely, how did it turn out?
dont worry i get notiffied :)
Another Great Video Sergio! Thanks for Sharing! Have A Super Week!.....Gus
Good informative video. Thanks for sharing.
It appears to me, that the threaded rod is not totally straight. It seems to have a slight bow which causes the wobble.
Maybe it's only on the video and not in reality. But it's easy to check it out.
Very nice job:) I must try it
Thank you, Well understood .......
well done looking forward to the rest of the build
buen video. apliqué un concepto similar en una hiladora electrica DIY que hice y quedó perfecta, sin ruido ni movimiento.
your Like,excelent and that was THE VIDEO that a was looking for. Greetings
you can reduce the wooble ich you make the distance of the bearings as long as 1/2 of the circle
diameter. think of it as terms of leverage, You are pressing with ~ 12cm againgst a 2cm Lever which is not good. Another method for improvement is you can add 1 bearing at each side on the outer corner of
the circle. (on the back side , so when you press against the disc from the front, the bearing on the back supports the rotating disc)
well done Bravo i liked it this video But i would suggest that you use your vise or clamps to press your bearing never use a hammer because that is the sort of thing that damages bearings and introduces wobbles or knocks in bearings
algo similar yo pense, al ver que se golpeaba con martillo, pero mi preocupacion estaba mas en que se produzca danhos a la rosca o a la punta del perno, no pense en el cojinete.
Para no danhar la rosca, normalmente uso una madera como amortiguador, o un metal blando como el bronce, o bien un martillo de goma.
nice job
I realy like your videos. I think you should make some ASMR whisper DIY Instruction videos too. You voice is so suitable for it.
what is your first language?
that's what i do when i made a table saw i used 4 bearings the saw blade is in the middle to secure from flying
Cool and after you scored the second subset they did not fall apart? As far as I know, when the clips are banned, they try to hit the edge of the padhinnik clip in order not to destroy it with hammer blows
thank you very night my friend
"if you like this shaft" hahaha
Very simple project, Sergio - I like it; the "wobble" you speak of, is a result of tapping the bearings onto the silvered pipe - it has made a slight shift in the bearings, themselves, even tho' the bearing is encased (they don't like lateral impact). My only suggestion might be that you press the bearing by using a vice, gradually tightening same. Excellent presentation - thank you, Andrew :D
Great Work My Friend!
How do you use this shaft in your disk sander? Have you made a video on it?
Design muito bonito entregue
Muy buen diseño. Gracias.
Gracias Sergio
Good work Sergio!
Very nice
Perfect.
God idea..👍👍👍👍
Thank you.
veramente bravo 😎👍👍👍
Очумелые ручки.
Nice
Could it be that the slight wobble is caused by the ends of the copper pipe not being quite square? Tightening the nuts would then cause the threaded rod to slightly bend.
Alan S 88m
Is this possible for a video on how it works in action.? Thanks in advance.
I can not wait to see how this actually works.
Sorry Sergio, I see now , The bearings are clamped into a frame to hold the shaft and the rod spins when attached to the disc and drill, I don't know what I was thinking, Sorry !
Thank you Sergio, I wait in anticipation !Cheers .
great bvideo
ide bagus..
good
How to run 12" shaft with pulley
SUPER SUPER SUPER +++++
...WOW, OKAY!!!
verygod your vídeo
Hala Madrid 🍒
bravissimo
What is the size of bearing you are not given in video
SUPER SUPER SUPER
super ball
muito bom
Little WD40,
to pur bearing on tube, and little play at begining....
but not in bearing.
ممتاز
I want that
hahahaha, as you can see it is quite easy to make 😃
are you trained as a machinist(i mean actual schooling for it)
Thanks for video!! I love them! :) Do you have a patreon account btw? I've started to donate a small amount to all the channels i watch.
Sleepydog i
Top💪🏻💪🏻💪🏻👍
👍👍👍
gut
Je Kaye may dalta hai
👍
Tempstar
My job hay sr...ji
Good video, could be done shorter.
hum !
Supar
melhor ele nao falar, eu nao entendo nada
看了半天不知幹啥用的
Mm
transmisan
hai
Linilbabu ck?
hi hi hiiii
What are vearings? Lol
wtf ??????? ahahhahahha
Серёжа , говори лучше на русском языке .
Sergio Acuña Padin pero aparentemente más ruso que el español .
Honestly that is the stupidest thing I have ever seen, why would you waste time and money doing this. Stop wasting time, go to Harbor freight and buy a sander. MY GOD!
Nice
good