At the 3:29 mark when they install the seal ring the proper process is to use an installation tool that can be purchased from a dealer. Using a screwdriver like they are risks damaging the rubber o-ring on the back of the seal creating a leak path. Also when these seals are installed a lubricant, such as isopropyl alcohol, is typically used on the o-ring. When done correctly installing that size of seal ring is easily a 1 man job.
I was thinking that. Here in South Africa when we install similar face seals like that we also wet the seal face with a drop or two of oil. I also noticed once the outer planetary carrier was installed they didn’t use any silicone sealant or lock tite ?? Is this normal procedure for CAT on these machines ?
The bearings preload is setted by that small cylinders in the drum, why they don't push against the drum but directly on the inner race of the bearing? In this way the drum is allowed to slide a littel bit on the spline, why? Thank you.
Where in the world are these fitters from? I used to do the same thing out in the field with cardboard and block and tackles. Good on you fellas. Hip hip hoorah. Best regards.
@@themountaineermechanictv Sa Saudi Arabia ba talaga, dahil sa nadidinig kong usap-usapan ninyo e puro tagalog kaya sa isip ko nasa pinas kayo. e Matanong ko saan lugar ito sa Saudi Arabia dahil tinawag mong mountaineer?
@@blessedchimwedzi6625 I got an experienced mechanic. But they need some time to reach Saudi Arabia. But do not mind if you have a diesel mechanic with at least 90% experience, an expert in the reconstruction of gearboxes, diffusers, gear sets, engines of diesel equipment, bulldozers, loaders, excavators and other diesel equipment .
you're right sir, the wages are small, I'm looking for someone to move to, I'm just finishing my contract and then I'll try to find a better job with a higher salary
At the 3:29 mark when they install the seal ring the proper process is to use an installation tool that can be purchased from a dealer. Using a screwdriver like they are risks damaging the rubber o-ring on the back of the seal creating a leak path. Also when these seals are installed a lubricant, such as isopropyl alcohol, is typically used on the o-ring. When done correctly installing that size of seal ring is easily a 1 man job.
I was thinking that. Here in South Africa when we install similar face seals like that we also wet the seal face with a drop or two of oil.
I also noticed once the outer planetary carrier was installed they didn’t use any silicone sealant or lock tite ??
Is this normal procedure for CAT on these machines ?
The bearings preload is setted by that small cylinders in the drum, why they don't push against the drum but directly on the inner race of the bearing? In this way the drum is allowed to slide a littel bit on the spline, why? Thank you.
Awesome job guy’s!👌😎👍💪
It's pleasing to see someone using hand tools rather than Rattle guns!
Excelente video!! Thanks for sharing!! Great work!!!
thank you sir you noticed my video, thanks also for the support on my channel godbless🙏🙏🙏
@@themountaineermechanictv ลงงล
งงลลงลลลล
ลล
งล
ลล
Where in the world are these fitters from? I used to do the same thing out in the field with cardboard and block and tackles. Good on you fellas. Hip hip hoorah. Best regards.
They are Filipinos working likely in Saudi Arabia or mid east.
Filipinos
these large dozers are awesome ,would love to drive and work on them .....
Next vlog master paano tangalin lining Nyan sir,shout out po.salamat sa video sir
Magandang araw sayo sir, sa susunod sir gagawa ako ng video about sa pag tangal ng lining nyan.. Godbless sir salamat sa suporta sa channel ko
Pre saan ang lugar na ito, sa Pilipinas ba?
Sa saudi arabia sir
@@themountaineermechanictv Sa Saudi Arabia ba talaga, dahil sa nadidinig kong usap-usapan ninyo e puro tagalog kaya sa isip ko nasa pinas kayo. e Matanong ko saan lugar ito sa Saudi Arabia dahil tinawag mong mountaineer?
Saudi sir, dto kami sa abha, aseer region
Pinoy kc mga kasama ko dto
@@themountaineermechanictv Malapit pala kayo sa Red Sea at Yemen. Gaano na kayo katagal diyan?
Kalaki ng sprocket
Hola lindo vidio
Unbelieveable, no grease was used in any of that assembly. I give it 100 minutes or 100 feet which ever comes first.
I was thinking the same thing.
У вас там запчасти есть на D7G катерпилер
Hello.. we need a diesel mechanic to work in Saudi Arabia, would you like that? Fahad from Saudi Arabia
Do yu stl need a diesel mechanic
@@blessedchimwedzi6625
I got an experienced mechanic. But they need some time to reach Saudi Arabia.
But do not mind if you have a diesel mechanic with at least 90% experience, an expert in the reconstruction of gearboxes, diffusers, gear sets, engines of diesel equipment, bulldozers, loaders, excavators and other diesel equipment
.
Saudi Arabia? NO! why? because it is very small salary.....accommodation no good.
you're right sir, the wages are small, I'm looking for someone to move to, I'm just finishing my contract and then I'll try to find a better job with a higher salary
@@blessedchimwedzi6625
yes
Nothing lubed on assembly?
Must have left the oily bit out. They're field guys, they're not stoopid, they filled it to level. Is it still gear oil?
ممتازجدا
COOL
very good working system
Forgot to fill with oil
There is oil, sir, but it was not included in the video
Wer ar you
Saudi aribia sir