Air hammer be like “look at me, I’m the Allen key” 😂😂😂 Big props to Cam for letting Carson take over, hard to find people who rather have the apprentice learn than to get the job done quick. My boss was like that with me when I started working for him 👌🏽
gosh this video couldn't have come at a better time than my final semester for trade school. we have been taking tracks off and taking apart old final drives for the last week and a half. Fantastic content as always. Cam, Carson, Brandon ya'll are the best! :)
A little tip a fella taught me spray contact cleaner on the dual cone seal rubber right as you put it on and it will shrink it a bit and make it easy as to put on then once the contact clean dries it expands, helped me out so much!
Just pulled a final drive off of a lamtrac yesterday, learned how because of the last video, boss was pleasantly surprised when he showed and and it was ready to come up, next gotta pull it apart
my favorite content :D so happy to see you Cam and Carson ! i'm saddly out of hd mechanic life for a while, cos last week while i was driving to work some douchebag without license crashed into my car, and now i have to heal my broken foot and ribs :( but i'm probably going to use this time into learning more can electronics and fixing those, so no time wasted. keep up the greatest content in youtube 👌💪
I am sure you already know about them, but sometimes left handed drill bits surprise me! Give'em a shot next time you have to drill out bolts. Great video Cam & Carson! 👍😁
You could also try using a torx socket thats oversized and smash it into the screw, thats usually what we did. Obviously not good for the sockets but it does a good job.
Hey guys! We'll all be at ConExpo 2023 from March 14-18th. Come say hi and meet us! We'll have merch to give away. Send us an email at media@tekamohd.com with job pics too and we can try to set up times. Also if you're local and want to do a truck tour let us know.
Do you guys not heat your bearings up to install? Have you found that tapping them in causes damage, even when tapping on the inner race of the bearing.
It’s part of being a tradesman and business owner is having to teach your apprentice the correct way to do things When he’s ready to go out on his own then the money will be made
Loving these vids. Just finished my Heavy Vehicle Mechanic apprenticeship in Australia. Tekamo is a serious contender to knock old uncle bumble fuck from my no.1 RUclips channel ranking
@@TekamoHD yup full show you betcha! Going with a friend of mine from Edmonton and he works on cat equipment. Should be a good time. I’m excited to see the big bud tractor that was just released to be shown at the event. If you don’t know big bud tractors it’s worth looking into. It’ll be something to see!!
I see you had a couple Ryobi’s. Any good? Wondering how they hold up. Thx for another informative and funny video. I enjoyed it. I won’t be at the ConExpo. How else can I get merch? Going to check to see if you guys sell it. Cheers. Watching from Ontario Canada 🇨🇦 🎉😊
We'll have a video out for the Ryobi stuff once we're done testing it out. As for merch, we don't currently sell it so send us an email at media@tekamohd.com and mention this comment thanks.
Rule of thumb I always use is a fist of sag. Lift the track off the Ground and between the bottom roller and the chain you should be able to fit your fist (measuring at the center of the track, where the most sag will be). Around 6-7 inches in between the very bottom of the roller and the top of the track chain.
Try equipment rental companies most are willing to hire and give apprenticeship especially for people who want to enter the trade. They’re a pretty good places because their shops are decently equipped, they have various machines and multiple of the same models, so there are margins for learning stuff.
I get you have to be there and you can see they get along and cam likes him bit I get so nervous when my boss just watches me and I mess up or forget to do the simplest things when I am being watched
I hate Allen heads. Just extracted the 2nd stripped level plug on my excavators final today. Happened on the other side last year. Pain in the ass. Luckily my harbor freight extractor set made quick work of removing it.
I see what you're saying, but that's cause they buff both faces before install. Sprockets sometimes also sit deeper one way than the other so it'll be misaligned by an inch or so if backwards.
Sir I'm haydurlic mechanic hevi equipment like D8R D9R 14H 14G 966D 966F DOSSAN 420 I have experience in 9 years india 15 years saudi arbiya still warking in saudi arbiya sir I nid Wark in canada can help me
Many many years ago company I work for bought a gray market komatsu PC 200 and trying to find parts for that thing was like trying to pull teeth out of a f****** little kid's head it was either right or wrong or nobody could find anything that's what you get have a nice day work on
![NLE Choppa - Or What ft. 41 (Orchestra Mix) [Official Music Video]](http://i.ytimg.com/vi/biOFASEgSOM/mqdefault.jpg)
SUPPORT THE CHANNEL and help us make more content! Buy rubber tracks, heavy duty tooling, and undercarriage parts at tinyurl.com/Support-TekamoHD
You know the kid is doing a good job because his boss is acting like that. If he was useless he''d be dead serious to him.
Air hammer be like “look at me, I’m the Allen key” 😂😂😂
Big props to Cam for letting Carson take over, hard to find people who rather have the apprentice learn than to get the job done quick. My boss was like that with me when I started working for him 👌🏽
Cam is a great stepdad to Carson. One of your best yet.
Cam is the most wholesome person ever great content guys
gosh this video couldn't have come at a better time than my final semester for trade school. we have been taking tracks off and taking apart old final drives for the last week and a half. Fantastic content as always. Cam, Carson, Brandon ya'll are the best! :)
Thanks Oz!! Don't forget Josh! He's the man.
@@TekamoHD HOW could I forget Josh!? He is the man!!
Glad to see Cam and Carson again !
Always great to see you in the comments Terry!
@@TekamoHD thanks !
A little tip a fella taught me spray contact cleaner on the dual cone seal rubber right as you put it on and it will shrink it a bit and make it easy as to put on then once the contact clean dries it expands, helped me out so much!
Just pulled a final drive off of a lamtrac yesterday, learned how because of the last video, boss was pleasantly surprised when he showed and and it was ready to come up, next gotta pull it apart
I subscribed about 4 minutes into the 2 guys one manifold episode, you guys deserve more subscribers, seriously good fun to watch
Thanks Ali, we appreciate it. Welcome to the Tekamo community!
my favorite content :D so happy to see you Cam and Carson !
i'm saddly out of hd mechanic life for a while, cos last week while i was driving to work some douchebag without license crashed into my car, and now i have to heal my broken foot and ribs :(
but i'm probably going to use this time into learning more can electronics and fixing those, so no time wasted.
keep up the greatest content in youtube 👌💪
Sorry to hear that, get well soon brother!
I am sure you already know about them, but sometimes left handed drill bits surprise me! Give'em a shot next time you have to drill out bolts. Great video Cam & Carson! 👍😁
I was waiting for another video! Thank you cam and the rest of the crew!
Welding is my 1st choice for getting stuck bolts out
Another win for the Camster, nice work Wrenchy!!
I'm gonna be sad when I catch up to all the cam and Carson adventures 😂 hope they can keep it up
Efff yes bud! Was waiting for another upload! Absolutely love this channel. More cam and carson on the road content please!
Glad you love the channel man. More to come.
Why use just brake clean on the seal? What's the problem with oil?
Great vidja thanks.
You could also try using a torx socket thats oversized and smash it into the screw, thats usually what we did. Obviously not good for the sockets but it does a good job.
Hey guys! We'll all be at ConExpo 2023 from March 14-18th. Come say hi and meet us! We'll have merch to give away. Send us an email at media@tekamohd.com with job pics too and we can try to set up times. Also if you're local and want to do a truck tour let us know.
Would love to do a truck tour for you guys but I’m in Ohio
See you there.
Mannn the clip whilw the air compressor was filling was epic. Best bit ive seen in a while. Cams always jokes though. Keep it up boys!
Great video! What made you decide to rebuild this final, instead of replacing it? Customer didn't mind the down time?
We Done this reseal job on a Hitachi uho63. Well done to all .
Awesome ! I rebuilt a final and travel motor in a 270 zaxis. At 16,400 brutal hours it went bluetooth
Your work is very helpful and great.
Great idea for the air hammer on the bolts
Happy new year to the homies. Cam bringing the laughs/skills to 2023 full tilt.
Happy New Year Chris!
Also do you shim to set the pre load in this bearing set up?
Do you guys not heat your bearings up to install? Have you found that tapping them in causes damage, even when tapping on the inner race of the bearing.
Great video. Thanks and keep up the good work.
thanks mr rusty nutz
It’s part of being a tradesman and business owner is having to teach your apprentice the correct way to do things
When he’s ready to go out on his own then the money will be made
Will be at CONEXPO 2023. I hope to run into you guys there
Right on! Come find us early and we'll have merch to hand out.
Had me creasing up watching this😂. Great videos! ❤
Glad you liked it hahaha
You guys need the Noco GB500 that thing is an absolute BEAST
What kind of
Cleaner does cam use in the pump
Up sprayer and where did he get the blue lifting chains? Great content
👍 great job 👏
These 2 should have their own channel
Awesome stuff guys 👍
Thanks for watching! 👍
I watch the videos for the dialogue between these two
I wonder how well the Mac RBRT hex sockets would work on the scummy fastners
i mean you could have given him a fresh rod that had the coating still on it. but i know gotta keep the skillgap ;)
ill have to try brake clean next time . ive always just just used Windex since its a dry lubricant.
Ran in these grey market machines with a Kubota kx185 excavator hopefully the customer was understanding
You just reminded me to grab my safety glasses with me 👍😅
Ya boy
Loving these vids. Just finished my Heavy Vehicle Mechanic apprenticeship in Australia. Tekamo is a serious contender to knock old uncle bumble fuck from my no.1 RUclips channel ranking
AvE is King
Thanks I've been waiting for this 1. Thanks guys luv it.
Hope you enjoyed it!
Did someone mention Premium Content ? When is that Likely to occure please ? Joking aside would an Inductor not work on the Bolts you drilled out ?
Nice work!
Thanks!
You make work boy!
Nice video guys 👍🏼 there’s always gotta be some kind of setback! 😅
Got a trip to con expo booked would be great to run into you guys there
Are you there for the full show? Shoot us an email media@tekamohd.com
@@TekamoHD yup full show you betcha! Going with a friend of mine from Edmonton and he works on cat equipment. Should be a good time. I’m excited to see the big bud tractor that was just released to be shown at the event. If you don’t know big bud tractors it’s worth looking into. It’ll be something to see!!
@@PrairieMechanic we'll check them out for sure. Come find us, we'll have merch to hand out if you want it.
I see you had a couple Ryobi’s. Any good? Wondering how they hold up.
Thx for another informative and funny video. I enjoyed it.
I won’t be at the ConExpo. How else can I get merch? Going to check to see if you guys sell it.
Cheers. Watching from Ontario Canada 🇨🇦 🎉😊
We'll have a video out for the Ryobi stuff once we're done testing it out.
As for merch, we don't currently sell it so send us an email at media@tekamohd.com and mention this comment thanks.
Carson : I'm a peacock! You gotta let me fly!
What wrench extender do you use for your big wrenches?
large mueller-kueps tinyurl.com/tekamo-fortis-wrenchextend
good work from scotland
Thanks Jeff 🙏🙏
Great video; a couple of questions, what do you look for in the correct track tension and how do you become an apprentice? Thank you for your time.
Rule of thumb I always use is a fist of sag. Lift the track off the Ground and between the bottom roller and the chain you should be able to fit your fist (measuring at the center of the track, where the most sag will be). Around 6-7 inches in between the very bottom of the roller and the top of the track chain.
Try equipment rental companies most are willing to hire and give apprenticeship especially for people who want to enter the trade. They’re a pretty good places because their shops are decently equipped, they have various machines and multiple of the same models, so there are margins for learning stuff.
I get you have to be there and you can see they get along and cam likes him bit I get so nervous when my boss just watches me and I mess up or forget to do the simplest things when I am being watched
Like using a radiator hose hook to put in the torque rings on duo cones. It’s slicker than goose shit on a pump handle
Carson and I was on the same page when he started doing the maths. Lol
He reminds me of Shorsey.
Another banger
I hate Allen heads. Just extracted the 2nd stripped level plug on my excavators final today. Happened on the other side last year. Pain in the ass. Luckily my harbor freight extractor set made quick work of removing it.
Question for you, Cam did you get a new truck?
Yes he did and we will do an update video on it
I wanna work with these guys now, where’s the dotted line?
When you were coughing from the dust your forgot to say "papa I think I got the black lung" zoolander 🤣
😂
Manual never shows enough information. He has his secrets...
Is the sprocket wrong way around? just look at the sand print on the front.
I see what you're saying, but that's cause they buff both faces before install. Sprockets sometimes also sit deeper one way than the other so it'll be misaligned by an inch or so if backwards.
Freezer
Contact Ireland for hitachi stuff. They know the most out of any other country by far when it comes to hitachi
I will work with you
Duo cone The Tool Sucks I do same way have a set of blunt tip screw drivers
OSHA was said at 2:06. If he says it 2 more times a puny man with taped glasses and a clipboard will show up.
Sir I'm haydurlic mechanic hevi equipment like D8R D9R 14H 14G 966D 966F DOSSAN 420 I have experience in 9 years india 15 years saudi arbiya still warking in saudi arbiya sir I nid Wark in canada can help me
Heat is your friend lots of it.
"Well I ain't holding s***" 💀
@ziptiesnbiasplies this you?
#Roger
I honestly would take an apprentice job just to learn how to talk that much shit and still be likeable.
At least give the kid a full rod
RYOBI!!! wtf Cam
Rbrt
What took you guys so long? It's not like you're out having fun because your prime minister doesn't allow it
There’s no way hitachi makes heavy equipment AND female sex toys 😂
Many many years ago company I work for bought a gray market komatsu PC 200 and trying to find parts for that thing was like trying to pull teeth out of a f****** little kid's head it was either right or wrong or nobody could find anything that's what you get have a nice day work on