How I consolized my Vewlix
HTML-код
- Опубликовано: 6 авг 2024
- ** Updated consolized video here • Vewlix - Consolized 2023 **
After cleaning out cigarette ashes, dank smoke smell and a few months of trial and error with parts I seem to have found a doable consolized Vewlix F setup. There is my ultimate wish that is all this could be done with a push of one button but hey, so far the DIY works.
I wouldn't have been able to do this without researching all the advice from the community via forum groups and just getting my hands dirty diving in and trying things out.
Thanks to everyone that create quality products to help keep the candy cabinet enthusiasts community thriving.
Enjoy!
** Disclaimer: My setup recorded at the time of this video is utilizing the stock Sanwa monitor which maxes out at 768p. If you are looking to run higher resolutions, you may need to find a KVM Switch, HDMI Audio Extractor and HDMI cables alternative **
Audio/Video:
- KVM Switch (MUST HAVE 2 separate USB 2.0 OR 3.0 INS FOR 2 PLAYERS): amz.run/5O9g
- HDMI Audio Extractor: amz.run/5OAV
- Volume Controller: amz.run/5OAb
- Volume Knob: amz.run/5OAa
PCB/Jamma:
- Psychic Drive - Brook UFB to Jamma: www.psychicdrive.com/store/br...
- Brook UFB: focusattack.com/brook-univers...
- Jamma Harness (pick the correct connection size for button type. Sanwa OBS = .110"):
retroactivearcade.ca/products...
- Rocker Switch: amz.run/5OAf
- USB On/Off (Cut open and wire only the power wires to the rocker switch): amz.run/5OAX
Joystick/Buttons
- Rafael Tamanini 2 Player Joystick and Subpanel
- Sanwa JLF: focusattack.com/sanwa-jlf-tp-...
- Sanwa OBS 30mm: focusattack.com/pushbuttons/p...
- Sanwa OBS 24mm: focusattack.com/pushbuttons/p...
- 24mm USB Hub: amz.run/6JsW
Inner Cabinet Compartment:
- Any Coin Mech: www.arcadeplastics.com/any-co...
- Dimmable Lights: amz.run/5OAv
- 8 Port USB Charging Station: amz.run/5OAt
Art:
- Artwork Set: www.ebay.com/usr/seiiseiiseii...
- Marquee Holder: arcadeartrepro.com/product/ve...
Keychain:
- Vewlix Keychain: arcadecandyco.bigcartel.com/p...
Link to diagrams:
- High Level Wiring Diagram: www.dropbox.com/s/8jiwbpm430p...
- KVM Routing: www.dropbox.com/s/6uyrdi2dj12...
- USB On / Off Toggle Wiring: www.dropbox.com/s/wu2kd77j3pm...
Damn bro! You are exactly what I was looking for!! I have the viewlix F and this is exactly what I been trying to do.
No bs, to the point, all the links, and the diagram. Your time is well appreciate it, honestly it is. A freaking life savor. You rock!!!
You got a sub my brother!
Awesome!!! Thank you so much. Hope it all works out and feel free to reach out if you have any questions.
@@MikeyNightchilde Brother this is amazing thanks for real everything so detailing
You are a wealth of information! I really appreciate the time you took to show step by step how you consolized your Vewlix. I've ordered one myself and I'm so glad there are people like you out there trying to help others. Awesome setup and thanks again!
Thank you so much!!! Super exited for you.
really enjoy the hands free aspect! cool video! makes me want to go back in and make things in my diamond more convenient so that i use it more. lots of work up front but less hassle in the long run.
Dood! That console switchy panel is genius! Great work fella!!
This is fantastic! I was proud just upgrading a TTX2 system and getting it up in a Vewlix Vs. I love the flexibility of your setup.
Oh man. I’d love to have a VS one of these days and a TTX. I kept most of the stock wiring in this F in the case I ever land one. I’d love to figure out the same KVM switch approach here but with a JVS loom to run both TTX and Brook for all the other consoles.
Amazing setup man all in one!!!!
Wow awesome setup. Thank you so much for that wiring diagram also!
Thank you. Just trying to make this as easy as possible for the community.
Great video 📹 I like the hands free approach I might try this on some of my vewlix cabs..
Thank you. It definitely takes a little work but worth it at the end.
Awesome! Just awesome. Wonderful setup.
Really clean set up
this is my dream setup for shmups and fighting games with a small factor PC in there.
I wish it was easier to get a viewlix
Wow that’s rad. Nice job browski.
Thank you.
Very nice man, well done
Thats freaking sweat bro, the switching between consoles is pretty badass
Wow excellent setup bravo bravo
great video - thanks for sharing
Cool, nice cable management, this is inspiring. For those looking to have both Jamma and Console, another alternative is to connect the brooks in parallel to the Jamma using the Brooks pinheader - save money on the Jammaizer and provide the same end result. Cheers!
Totally true. I didn't think about that. You could also use one of these Brook Fighting Board Cables that hooks into the pinheader and cut the end of those wires to go parallel into the Jamma harness if you don't want to solder straight into the header. That way you can switch into newer Brook boards when the PS6 or Steam Deck Pro 2 comes out in 2030. www.brookaccessory.com/detail/59387342/
@@MikeyNightchilde that's more or less what I did, I connected the Brooks to the panel using the Brooks harness, then collected the JAMMA wires in parallel. This way if I connect a console or PC, the Brooks are used. Otherwise, if I connect a jamma board, it works just well. This is the fun part, there are so many ways to do it that it's fun to see how people do and tweak or setups.
Now I’m brainstorming even more.
Yoooooo this is amazing!
Great stuff! I've just picked up a couple of Dia Blues myself and I've been looking for some inspiration for multi console/PC setup and you've given me some great ideas. I really appreciate you adding the parts list and the wiring diagram, thank you! One question, what is the front end(?) that your using?
Thank you. Score on the Diamond Blues. I was be so stoked to add a Diamond Black to my collection. The front end for the PC is CoinOps Arcade Elites 2 and for the Raspberry Pi I'm running Nostalgia Dreams. Here's links about what's in both. Enjoy!
ruclips.net/video/-yV1zC-AhYs/видео.html
ruclips.net/video/a__yhrErXtk/видео.html
Hey there, I really appreciate you sharing your process and being so transparent in regards to how you customized your cabinet.
I have a really basic question, but with the 24mm USB hub that you've shown in both videos that replaced your 2p share button: did you do anything specifically to get it to mount into the panel? In the video it looks like there's a thread like it's housed in a push button rim but you took out the plunger but from the link you provided it looks like it's a panel mount that requires screws.
Hi Chris. Looks like that link is going to an updated version of that USB hub. The previous version had a threaded back where you were able to mount by screwing in a washer and nut. Here's a similar product. Going to change the link in the description. amz.run/6JsW
@@MikeyNightchilde Ah! That's perfect and explains a lot. Thanks so much for the reply and the new link. I really appreciate all of your help. Thanks again!
I also love Deathsmiles!
If you’re into modern arcade cabinet design, I do a really neat wall mounted model for Umbrella Arcades.
Any chance you can show how you mounted your volume controller to the bottom of the sub panel?
Hi, I have a Vewlix F and am planning on converting the 1p to a 2p panel. I will be using a Taito Type X3 PCB. The cabinet has a JVSIO. I'm wondering if I need to buy a kick harness and if so, where I can buy one. Basically, I don't know what I need to buy apart from the 2p panel itself, buttons and joysticks in order to hook everything up properly.
Nice.
How did you mount the volume control?
Where you get your cab?
Awesome Video . This is very helpful . I recently ordered a Vewlix Black Diamond and want to run some consoles in it. I have a quick question . What is the Nintendo Switch Dock you are using?
Thanks Aaron! I would love to get my hands on a Black Diamond one of these days. As for the Switch dock, it’s the “BASSTOP portable dock replacement”. Basically an empty case where you transfer over all components from the stock dock. The reason why I went this route is because there was a huge issue in the past where a Switch firmware update caused consoles to fry when plugged into a third party dock. So this was the best solution to have a slimmer doc without having to worry about it blowing up because it's the same stock components. Unfortunately, it’s out of stock on Amazon but you may be able to find it somewhere else.
Just to add if you view my Vewlix Consolized - 2023 video, I now have my Switch laying on it’s side and the dock behind the Taito Amp PCB (I think the Diamond will have the same space) using this extender cable. amz.run/6P4z There’s enough room to put the stock dock behind there if you are looking for alternative solutions to put the console in the cabinet.
Hope this helps.
@@MikeyNightchilde Cool Thanks so much for all the information . I appreciate it. I had no idea about the dock issue . Glad I asked :)
@@AaronKraten Totally, reach out anytime. You can hit me up on IG too. Been following your stuff for awhile. Stoked you're adding a Vewlix into the mix!
@@MikeyNightchilde Will do . Super stoked on the help ! ohh how did you mount the KVB ?
@@AaronKraten This video I used heavy duty velcro but gravity just peels it off. Probably the heat of the metal after awhile. Now I'm using Zip Ties with no issues. www.dropbox.com/s/zf97aqzozvahzy2/IMG_4710.HEIC?dl=0
The link for the jamma edge is dead. Also, how did you know which wires went where and how did you get additional buttons from jamma to pair to the extra buttons in the two control boards? Jamma shouldn’t be able to run so many so I’m just confused.
Thanks for pointing out the bad link. I just updated it so you should be good to go. As far as extra buttons, you will get those directly from the Brook PCB through screw terminals or one of the headers. Look at their specific diagram for the PCB you get. You are correct that JAMMA does not provide all buttons. Look for a JAMMA diagram on what number is what button and then use the specific Brook pcb diagram to figure out the additional buttons. Also, I'm assuming you are using this for Vewlix. If it is already setup for JVS then you can instead just skip JAMMA all together and get this. www.hadouken-arcade.com/collections/hardware/products/vewlix-custom-io by Hadouken Arcade or this arthrimus.com/product/vewlix-console-i-o-v2/ by Artrimus. Then you don't have to rewire your whole setup. Again for the additional buttons, you can just get them direct from our Brook PCB. These did not exist at the time when I made this video. It would have saved a lot of time. Hope this helps.
Can you link me to the switch for the Brooks used in your sub panel please?
Hi Victoria. The part is called Rocker Switch under my parts list in the description. Make sure it's the 2 Pin version. Here's the link. amz.run/5OAf
Can you explain how you wired up those Brook board power switches?
Hi there,
Thanks for the question. I've updated and added into the description a link to a USB On / Off Toggle Wiring diagram.
In my parts list I am utilizing two items. USB On/Off and Rocker Switch. For me I also needed a USB A Male to B Male to connect it to the Brook and a USB A Male to USB A Female to connect to my KVM switch.
I broke open the USB On/Off casing and cut the 2 power lines connected to its switch. Be sure not to cut the data wires. Keep those intact. In my setup I additionally needed to reach my Subpanel, so I soldered 22 AWG extension wires to each end of the power lines and crimped 6.3mm female terminals on the other ends. Both those terminals fit onto the Rocker Switch's 6.3mm male ends.
Probably not the most earth friendly approach since I threw out the plastic casing. You could accomplish the same thing with less parts with a regular USB A Male to B Male cable if you can figure out which wire inside holds power.
Hope this helps.
Is the brooks board hooked up to the consoles wireless?
They are hard wired.
so i got an extra button panel off of the facebook group, but was not able to fit the rocker switches into the square usb holes. did you make any adjustments for yours? or did they just snap in and fit?
Hi there. The switches that I have linked in the description fit perfect on my Subpanel. I didn’t have to do any alterations. I’m thinking maybe it all depends on who made your Subpanel. Mine is from Raphael Tamanini.
@@MikeyNightchilde yeah same maker, my rectangle slots are just a tad bit too small, I think it's for the USB plugs only. When you ordered did you specify you were using rocker switches? I just assumed it was universal, aka my fault. Oh well thank you for answering.
@@buntholkim2981 Yeah, I didn't specify anything to Raphael. Maybe the cut changed.
at the end did you drop coin in for credits or just for fun. does it work
Hi Adam. The coin mech totally works. I had to run a wire from the Brook instead of using the existing wire.
Aquí en México donde pudiera conseguir una máquina así
You should put a MiSTer FPGA in there.
Oh yeah! I own two. One sat in the Vewlix in the past but now they are both in CRT cabinets. I decided to go modern games in the Vewlix now that I upgraded the monitor. I’ll let the retro MiSTer titles run on a proper screen size which looks absolutely beautiful. Right now it’s PS5, mini PC and Switch.
Where can i get one of these?, full cabinet or just the case
Hi there. That all depends where you live and who in your community could be distributing these machines. Your best bet would be to dig into forums like www.arcade-projects.com. I live in middle United States so I ended up going with KC in California. www.arcade-projects.com/members/kcarcadegame.593/ . There's also a few candy cab related facebook groups where I see Vewlix cabinets for sale all the time in Europe, USA, Australia, etc... You could also go the Chewlix route as well which is a Chinese knock off at a cheaper value. I've seen these on Ebay too. Happy searching!
Hey dude, where is the best place to get an Empty cabinet? I have buttons, joysticks, etc everything but a 32" monitor to populate one. but I'm just not sure who to trust on those Chinese import sites.
Hi @JJiG.
I have seen this question thrown around in the past about locating an "Empty" cabinet to purchase and I don't think it exists. Unless there's a blank Chewlix available, a Vewlix is going to come 90% equipped.
Your location is a big factor as well if you are looking to get the best deal on shipping. There are region based vendors that will do group buys to save on shipping costs. You'll have to do some digging. There are great FB groups related to Candy Cabs where the community helps each other with buying and also share a ton of knowledge to get up and running. There's also one specific to Vewlix. They will vouch for good or call out bad sellers. I've seen some vouch for Chinese vendors too. So great resources.
The arcade-projects forum is another one with tons of knowledge and sellers.
Good luck.
@@MikeyNightchilde Thanks man, I never saw a notification for this reply but I'm glad I revisited the video to find out about the psychic board for the brooks controllers. I'm trying to find a video on how it works but I can't seem to find anything, besides the website to buy is there a place to find some info? I have the Brooks Zero Pi fighting boards, so they are a little different but still have the 20 pin header found on the rest. Would those still work do you know?
Great job on this. Is there a way I can message you either by email or facebook? I am trying to do something similar and needed some help with understanding the psychic board pinout for the jamma harness and looking at your video looks like it is not wired up as a regular jamma harness to a power switcher. Also want to see if you had a link to the usb hub you used on your sub panel in the second share space.
Hi @dnsputsitdown1. Let's keep the convo going here just in case anyone else down the line has the same question. First off, here's the link to the USB hub. amz.run/5swx Depending on what Subpanel you are using, you may need to add an extra washer to get it to screw down all the away. As far as your setup, are you currently running JAMMA? What are you looking to run in your setup?
@@MikeyNightchilde Thanks. Yeah I ended up finding that usb hub last week after doing some searching around for quite a bit for that size. Also I might have figured everything out. Just waiting for this monitor bracket to come in tomorrow before testing everything. I will report back if I run into any issues. Thanks again for the reply.
Hi. I finally got my monitor installed and everything wired up. I'm running into a few issues. Main one is no matter what I do I can not get any of the buttons & joysticks to register. I have pretty much the same setup as you. I can't find any info on the on/off hit a certain button config to put brooks boards in console or pc mode. I see that you are doing it, but I can't find info on which buttons or how to set that part up. I even tried to remove the brook board off of the psychic drive board and run a usb directly to my ps4 and touch ground and any direction with a wire and sell go nothing. The on/off switch is working correctly going to the brook boards. I have the jamma harness connected to all the buttons. I have no power connection connected to the psychic drive board. Just having a hard time figuring out why the ps4 or ps5 console is not seeing the movements on my vewlix control panel.
@@dnsputsitdown1 Hi there. Glad to help.
Is there a chance you can elaborate on the routing of your setup? Like Console(PS4) > KVM Switch > Psychic Drive / Brook > JAMMA > Buttons
First off we need to know which Brook PCB you are working with.
Start here: www.brookaccessory.com/Fighting%20Board/list.html
Find your PCB and click MORE. Scroll down on the page and find a Manual Mode or Console Mode list that will show the button config. If you don’t find it on the page you may need to click the User Guide download link.
Make sure you are correctly routed from your JAMMA harness to each appropriate button and joystick direction with emphasis on the ground correctly connected to each as well.
Test directly into the PS4 USB without your On/Off Toggle. With the PS4 shut off, unplug the Brook from the console's USB. Turn on the PS4. Once it fully loads the HomePage UI or prompts to ask for a controller, hold down the Console Mode button config you looked up from the Manual, and while holding it down plug the USB back into the PS4. The Brook PCB LED should light up (depending on which one you have, some do not). Now hit your HOME button. You should be good to go from there.
If this works you should test with the On/Off toggle next.
Side Note: You mentioned PS5. The PS5 will only work with the Brook UFB PCB + UFB-UP5 combined. I don’t own a PS5 so I have not tried this in my setup. Looking at how this is hooked up you may need to somehow rig wires to the J2 header to hook up to the UP5 since the UFB PCB is plugged in upside down onto the Psychic Drive.
Hopefully this helps. Let me know how this goes.
@@MikeyNightchilde Ok So this is where I am at now (btw thanks for all your help thus far). I got the control panel to work using the config on the website. The problem I have now is I can only get it to work by plugging the usb from universal brook boards directly into the front of the ps4 or ps5 and doing the config. When I try to use the toggle method thru the kvm switcher and apply the same order config it does not register the joysticks or buttons. The toggle switches are turning off & on the brooks boards like they are suppose to, but are not registering the control panel joystick & buttons to the ps4 or ps5. I have the on/off toggle switches going from the brooks boards into the tnp hdmi switcher USB1 & USB2 slots. Hdmi coming out the ps4 into the kvm switcher input 1 on backside. Hdmi out from kvm switcher to the input hdmi of extractor. Hdmi out of extractor to monitor. Other issue I have is the ps4 not displaying on the new monitor I installed through the kvm switcher & audio extractor. It will work bypassing those two items though I think for this problem I might have to go with a newer switcher & extractor. For now I'm just using a computer monitor until I get the control panel figured out.
What I have is the exact same parts that you have minus the new wireless brook board you added. (E Synic 4k HDMI Audio Extractor, Psychic Drive Board, Universal Brook Boards that have been updated, TNP $K HDMI Switcher, Jamma Harness, Toggle switches, Vewlix with 8 buttons, 2 joysticks, and sub control panel unit)
Hi nice work !! Im looking for a kwm switch for my cabinet but its impossible to find a hdmi/usb in and out :s the link you put for your kvm is not working :s can you send me the detail or photo of yours ? it will be great :D thank
Jump on this one! I own and tested this version as well. It is the exact model as the Japanese one in the description but with a US manufacturer print on the case. Hope this help. amz.run/5gSX
@@MikeyNightchilde thanks you very much, i finally finish my cabinet and i have a big problem with usb hub, hop this can help ;D
@@MikeyNightchilde sorry, but one last question, how you connect 2 players for ps4 on the kvm ? there is juste 1 usb connection? :s thanksss
Hi @@klhone9856
You can use 1 single USB in on the PS4 for 2 controllers. I have a PS4 Pro which includes a single USB in the back of the console. Makes it clean looking and totally works. Same for Nintendo Switch, Raspberry Pi, PC etc. You should be good to go.
@@MikeyNightchilde many thanks for your help :D i tried to order the kvm but it's only avalaible in the us :s damn