I bought a used mower and cleaned carb and saw this part today and thought it looked rough and mower gave me he'll to start but I finally got it. I'll be doing this soon thanks for the video. Sounds like you saved many mowers and heartaches.
I was having the same problem and had it narrowed down to this component but cutting the pin off solved the problem without having to buy a new one. As a note to others, there is a small copper washer that needs to go back on to prevent a gas leak, so be careful not to lose it when you remove this part. Thanks for the tip John!
I want you to know you saved me some heartache and pain also a lot of time as my mower is still under warranty repair shop said they would not get to for 4 weeks. Modified the fuel solinoid and the mower is back in business! You are the man! I hope you get a lot more subscribers as you deserve it💵
John Sellers, THANK YOU for sharing you experience and saving so many of US so many headaches !!!!!!!!!!!!!!!!!!!!!!!!! I've just followed your instructions and my 4 year old Husv. is working like new again. May the LORD bless your journey and your day. :) :) Thank you again for your very giving attitude and GRAND explanation with LOT"S of video. respectfully, your new OLD carpenter friend :)
You're a lifesaver! I went the magnet route, put 4 neodymium disc magnets from menards on the bottom and mower is running like it is brand new! $17. Added bonus is thati now have a perfect anti theft device when i stop mowing and move magnets to the oil filter next door. Thank you!!!
My Husqvarna died on me today for the first time in 12 long years! This video was the FIRST that came up for my model number, and from the time I clicked on the link, til the time I was cutting grass again, was about 10-15 minutes; Thanks John for the solution!! I just used a cutting disk on my dewalt grinder and cut the top quarter inch off the pin, replaced the copper washer, and screwed it back on with a 12mm open ended box wrench.
John, I hope you are alive and well and read this because this video was absolutely amazing and spot on with what I kept asking myself "why does it turn over for a full two seconds and then just stop instantly and not crank". Tractor would do this every try after I would wait a few minutes. I spent hours googling, watching you tube and troubleshooting and they just did not add up to the issue I was having. Followed your awesome directions and it fired right up. I never saw this part mentioned anywhere else as something to look into. I subscribed to your channel to see what other fixes you may have out there. Thanks so much...its been a long day but, at least I can mow my yard now.
I pulled my fuel solenoid and tested it and it seemed to be working. I went to Lowes and purchased hex nut m8-1.0 and hex cap screws m8-1.0 x12 and made a plug to plug hole. Mower fired right up. Even though fuel solenoid acts like it’s working doesn’t mean it’s not faulty. Thanks for your post, my friend.
I hardly ever leave comments, but you saved us a ton of time trying to get it start. We cut that piece off and it was fixed immediately! Thanks so much!
THANK YOU! Can't believe that just worked. I have the same exact ride on mower and it was doing the same thing you described in the video. I first thought it was just a spark plug since it had been awhile since I last changed it. Nope, it was that little "doo-hickey" causing the problem. So grateful for people like you that post videos to help others. Thanks again!
I never leave comments, but this one is well deserved. I changed the spark plug, installed new push rods, adjusted the valves, new oil and filter, and new battery. Gave this a try and it cranked up and started after 3 seconds because the gas had drained out. next start cranked once and started with zero problems. Thanks for the video and the knowledge!!! very much appreciated!!!
This was the problem I had. After a few hours of taking the carb off and cleaning it multiple times, getting covered in fuel, still no luck. Would turn over, but not fire. Watched this video, and literally 6 minutes later it runs great. Thanks!
I want to thank u so much, I am no mechanic but I took the carburetor apart and cleaned it I cleaned the tank I Checked all the gas lines and the switch under the seat……. Nothing. But I found this video and u saved me not only money but time cause I had no idea what to do next. I appreciate this video from the bottom of my heart and appreciate u taking your time to make this video to help people like me out. I gave u a big thumbs up thank u
Thank you thank you. I purchased part on Amazon $14 next day delivery. When I went to local repair shop they said most likely not the problem. WRONG! Your a genius! Great advise. Thanks again!
I’ve been working on mowers for almost two decades now and can say they are so full of shyte, that fuel solenoid pin gets stuck and is often the cause of no starts with riders that have them.
Amazing video. Was pulling my hair out doing all the normal things , checked fuel filter changed plug replaced ignition coil. This was it the whole time. Started right up thanks so much
I would like to join the chorus of thanks in these comments. You saved me a lot of trouble. My yard is an acre and I’m too old to cut the whole thing with a push mower. Thanks for helping me get my mower working.
Got a Husqvarna riding mower 2years ago. Past Saturday just stopped running. Knew getting gas to carb. an spark plugs firing. Seen video, tried switch, no click, took solenoid off an cut stem off, runs like charm. Thanks so much for video, saved me money!!!
I had already cleaned the carburetor twice before I found your video.today..cut that little needle off like you said and it fired right up....thank you for the video
THANK YOU!!! YOU JUST SAVED ME $$$$! I was cutting grass and mower suddenly shut off. Couldn’t restart. After cleaning carb it wouldn’t start. I did what u did and ding ding, started right up. However, when i plugged the solenoid wires back in, they started burning, melting and smoking. I unplugged solenoid and so far it starts and runs like before. I’m no mechanic, but I’m pretty sure the wires don’t need to be reconnected since that part now serves no purpose to the mower. Woohoo!!!!!
I started the video as someone very skeptical but gave in and tried it. Shaved off the part just as you said. Turned the key and it started right up. Thank you very much for your help
DUDE That fixed it. I pulled the seat switch out. I replaced the fuel filter. I was looking up replacement parts for the entire fuel system. My mechanic son found your video and forwarded it to me. Mine was spinning. Couldn't hear the click. Pulled the part out, ground down the internal piece. Put it back together and it cranked right up. Sweet. Thanks for sharing.
Thank you Sir for your helpful information i have the same kind of lawnmower and the same problem with mine i did exactly what you said and it started rite up…… thanks 🤝
Have tried everything except this fix. Will try it tomorrow. Cant wait to see how it goes. This is FYI ok? A mate who worked at a mechanic shop told me once how they fixed a very small 2 min fix problem on a womans car who left it at the shop for the day. It was a loose distributer lead causing a run rough situation. The mechanic listed a whole lot of BS fixes he said he did and charged her $700. I had a similar thing happen on my car brakes... but you cant argue with them while they hold your keys lol. So when the local mower man wanted me to deliver my Husqvana to his shop for a few days... I said forget it mate. haha.
Thank u. I know nothing about small engine. And I really impressed my wife and got lucky later that night. U the MAN !! She was using the mower when it shut off and was sick that she broke it. Thanks again. !!!
Thanks so much. I am useless but i was able to do this quickly and it worked just like u said. My neighbors (and wife) are going to be shocked that i fixed it myself
I have the same model mower and it shut off while I was mowing a couple weeks ago. Couldn't figure out what the problem was getting it to start. This worked on the first try! Thanks!
Great video...one exception comment. Bypassing your backup blade shutoff. I use to want to do that to my mower, unfortunately I work in an Emergency room and had a little baby girl that got run over by a mower that was backing up and ran over her leg. Really really bad scene, lost a limb and had to live with it because of that reason. I feel for the family because it was a total accident. No one knew the child was outside. I use to want to do that to my mower but now have to say there is hardly a time that I don't back up on my mower that I don't think about this child. My kids are grown and have no children but you never know. Could be a child, a pet or something. Not worth it.
My yth 18542 does not cut same on 4 l reach under deck and right blade spins around but left blade turns like it's in gear u can turn but tight right u can spin around can u help please
@@Tommy-m2f i had same problem,bushing were bad in the spindle,i took deck off,and replaced both spindles myself,put new blades while i was at it.I got a pair of new ones from Amazon for 43 dollars.Blades spin very easy now and QUIET,i replaced belt while i was at it. I have never worked.on a mower,the hardet part was getting the old bolts out,4 botls in each spindle,i used a impact drill with a socket adapter and lots of bolt loosening spray. Many videos on utube how to change spindles on this mower.
Thank you my friend for sharing that video, that was a big help I was going a little crazy try to find the problem, found out a very small thin had to cut off and the lawnmower won’t start right up, your friend on the big Island of Hawaii thank you (aloha)
I have the same problem and the same exact mower. Tomorrow's payday but today will be perfect for mowing. I'm hoping that this will fix it! 🙏🏻🙏🏻🙏🏻 I'll edit if it works. I'm almost positive it will based on the comments.
@@Jsellers1965it didn't work. I've tried everything. I'm a mechanic that makes a fantastic living but my luck with anything that runs on gas just doesn't exist. I've no idea what is wrong with this POS!!
THANK YOU! I did everything I could think of but it still wouldn't run. Tried to buy a new one, but nobody has any riding mowers under $4K. I will make it thru the summer now!
Took solenoid off, also checked electric to it, Yes to power but solenoid didn't function when reconnected and turned key on. Pretty sure (99%) that is my problem. Ordered new one from amazon $12.99 get it in 4 days. Thank you for the info. Lowes said they'd fix it but would take 4 weeks, have to ship it to Tampa 4 hours away. Suggested I take it to local husqvarna dealer for faster service, I called local dealer and they said since I didn't buy it at their store they will have to let it sit for 3 weeks B4 they would look at it. Gonna report them to Husqvarna and will tell Lowes (where I bought it) about the dealers B.S.
I have the same lawnmower been having problems out of my every since I bought the thang thank you sir now my lawnmower won't turn over with the key I have to keep bumping the key to start it ughhh
John I have a 2006 yth26hp and i have a problem with the mower starting after engaged deck, the pully on the left side if on the mower there's no belt on it and i tried loweing the deck to 1 so could check it out and wont go past or to 2nd like locked there, had deck check and they supposedly put new pulleys and belts last Spring but im not so sure they did, has like a clanking sound when engaging deck but now trys to start but will not turn over fully! Any suggestions?
i just bought the husqvarna yth 21546 --- my problem is it wont start. I put fresh gas in it, charged the battery and the oil level is fine. It cranks good but just wont start? This thing is brand new and ive never been more frustrated. Is there some easy adjustment that can be made or should i return the mower??. In the troubleshooting manual-- it mentions fuel valve lever--- i didnt notice this.... wheres this at? engine is hv 703
Fuel valve should be right by the Carb or on the fuel line leading to it. It should be red. You might also have the same problem with the part in question in my video. It may be stuck closed. Your warranty would mean you would have to return the mower to where you bought it, in my case lowes, and they will send it out to be fixed. Or you might have to have a small engine shop look at it.
My YTH has to crank and crank with the choke on, even on really hot days, before it will finally start. Wouldn't doubt if it's related to this "feature".
@@moto-fl3rd Common problem on these is for the choke cable to be improperly set from the factory. Works for maybe the 1st season without any choke at all (even tho you think you are engaging it) because the motor is so brand-new perfect, but with normal wear needs real choke. 30-second fix. Loosen & readjust choke cable at that 1 screw that holds the middle of the choke cable to the side of the motor. Check at the end of the choke cable where it comes to the motor that the cable is actually pushing the lever as far forward as it can go... so the choke is really being engaged. No more starting fluid needed.
Hi there I got a question for you for casually you know what's the camshaft number on my husqvarna 18.5 hp briggs and stratton intek engine I can't find the right number?
John, I have a very similar Husqvarna, same issue it was having, STARVING FOR PETRO, I took the carb out, , I looked at every wrench I had, I had nothing that thin until I took a 12 mm wrench and grinded down until it fit in the area. I took off the bowl, I had seen no gas in the bowl, I CUT THAT DAM PIN OFF, put everthing together within the hour, AND IT RAN LIKE A CHAMP.. YOU CERTAINLY HELPED ME ON THIS ONE.. Years ago they never had those little gizmos, they just add more hedache.. THANK YOU AGAIN JOHN Now I feel the deck shaking more than it should, do you have a remedy for this?..🙂
@@jayholland4949 Thanks for the advise. I had just installed a new($10) fuel shut off solenoid. Worked great for the first mow after. Would not start a week later for the next mow. I tried the magnet, and it started right up! It must be a problem with the cheap solenoid. Maybe too tight. You saved me!
Did you put a cut off valve on the gas line? I did cut the pin off and it fixed the problem. My gas line have a cut off valve and apparently the valve is leaking cause I just put over a quart of none ethanol gas. The next day I have gas inside the engine oil and a flooded carburetor. So I am going to remove the line from the carburator and put some gas in tank and a container. If the container fill with gas. That means that cut off valve is defective.
Parts Listed in Description on Amazon
Part for Carb on Amazon (Prime Day Deals):
amzn.to/44BgeV1
Carb kit: amzn.to/3NQ6AqK
Changed air filter, oil, oil filter, spark plug, fuel filter.... and then did THIS. AND IT WORKED. THANK YOU SO MUCH!
I bought a used mower and cleaned carb and saw this part today and thought it looked rough and mower gave me he'll to start but I finally got it. I'll be doing this soon thanks for the video. Sounds like you saved many mowers and heartaches.
I was having the same problem and had it narrowed down to this component but cutting the pin off solved the problem without having to buy a new one. As a note to others, there is a small copper washer that needs to go back on to prevent a gas leak, so be careful not to lose it when you remove this part. Thanks for the tip John!
I want you to know you saved me some heartache and pain also a lot of time as my mower is still under warranty repair shop said they would not get to for 4 weeks. Modified the fuel solinoid and the mower is back in business! You are the man! I hope you get a lot more subscribers as you deserve it💵
After 2 days of messing with my mower and a lot of cussing, tried what you did and it solved it. I could not thank you enough. 🙌
John Sellers,
THANK YOU for sharing you experience and saving so many of US so many headaches !!!!!!!!!!!!!!!!!!!!!!!!!
I've just followed your instructions and my 4 year old Husv. is working like new again.
May the LORD bless your journey and your day. :) :)
Thank you again for your very giving attitude and GRAND explanation with LOT"S of video.
respectfully,
your new OLD carpenter friend :)
You're a lifesaver! I went the magnet route, put 4 neodymium disc magnets from menards on the bottom and mower is running like it is brand new! $17. Added bonus is thati now have a perfect anti theft device when i stop mowing and move magnets to the oil filter next door.
Thank you!!!
My husband tried all the obvious things to fix ours and we are so grateful for your video. Worked exactly like you said!!
My Husqvarna died on me today for the first time in 12 long years! This video was the FIRST that came up for my model number, and from the time I clicked on the link, til the time I was cutting grass again, was about 10-15 minutes; Thanks John for the solution!! I just used a cutting disk on my dewalt grinder and cut the top quarter inch off the pin, replaced the copper washer, and screwed it back on with a 12mm open ended box wrench.
I'm glad it helped.
John, I hope you are alive and well and read this because this video was absolutely amazing and spot on with what I kept asking myself "why does it turn over for a full two seconds and then just stop instantly and not crank". Tractor would do this every try after I would wait a few minutes. I spent hours googling, watching you tube and troubleshooting and they just did not add up to the issue I was having. Followed your awesome directions and it fired right up. I never saw this part mentioned anywhere else as something to look into. I subscribed to your channel to see what other fixes you may have out there. Thanks so much...its been a long day but, at least I can mow my yard now.
I'm alive! Thanks!
This saved me so much time and money. Thank you! My mower fired right up after removing that pin!
I pulled my fuel solenoid and tested it and it seemed to be working. I went to Lowes and purchased hex nut m8-1.0 and hex cap screws m8-1.0 x12 and made a plug to plug hole. Mower fired right up. Even though fuel solenoid acts like it’s working doesn’t mean it’s not faulty. Thanks for your post, my friend.
I hardly ever leave comments, but you saved us a ton of time trying to get it start. We cut that piece off and it was fixed immediately! Thanks so much!
THANK YOU! Can't believe that just worked. I have the same exact ride on mower and it was doing the same thing you described in the video. I first thought it was just a spark plug since it had been awhile since I last changed it. Nope, it was that little "doo-hickey" causing the problem. So grateful for people like you that post videos to help others. Thanks again!
I never leave comments, but this one is well deserved. I changed the spark plug, installed new push rods, adjusted the valves, new oil and filter, and new battery. Gave this a try and it cranked up and started after 3 seconds because the gas had drained out. next start cranked once and started with zero problems. Thanks for the video and the knowledge!!! very much appreciated!!!
This was the problem I had. After a few hours of taking the carb off and cleaning it multiple times, getting covered in fuel, still no luck. Would turn over, but not fire. Watched this video, and literally 6 minutes later it runs great. Thanks!
Just watched your video and my mower was doing the same thing. So I tried cutting the pin and sure enough it fired right up. Thanks for all your help
I want to thank u so much, I am no mechanic but I took the carburetor apart and cleaned it I cleaned the tank I Checked all the gas lines and the switch under the seat……. Nothing. But I found this video and u saved me not only money but time cause I had no idea what to do next. I appreciate this video from the bottom of my heart and appreciate u taking your time to make this video to help people like me out. I gave u a big thumbs up thank u
Glad it helped
Thank you thank you. I purchased part on Amazon $14 next day delivery.
When I went to local repair shop they said most likely not the problem. WRONG!
Your a genius! Great advise. Thanks again!
I’ve been working on mowers for almost two decades now and can say they are so full of shyte, that fuel solenoid pin gets stuck and is often the cause of no starts with riders that have them.
Amazing video. Was pulling my hair out doing all the normal things , checked fuel filter changed plug replaced ignition coil. This was it the whole time. Started right up thanks so much
I would like to join the chorus of thanks in these comments. You saved me a lot of trouble. My yard is an acre and I’m too old to cut the whole thing with a push mower. Thanks for helping me get my mower working.
Got a Husqvarna riding mower 2years ago. Past Saturday just stopped running. Knew getting gas to carb. an spark plugs firing. Seen video, tried switch, no click, took solenoid off an cut stem off, runs like charm. Thanks so much for video, saved me money!!!
I had already cleaned the carburetor twice before I found your video.today..cut that little needle off like you said and it fired right up....thank you for the video
Man you’re a life saver. Thank you so much for this video! Cut that piece off and she started right up! You deserve a million likes
I just watched your video and followed what you did and it cranked right over and is running smooth! Thanks for the fix!!
Mine was doing the same thing and by following your directions I got it running like new…Thank You for sharing
Glad I could help
Worked like a charm! I spent a few hours scratching my head. Thank you!!!!
THANK YOU!!! YOU JUST SAVED ME $$$$! I was cutting grass and mower suddenly shut off. Couldn’t restart. After cleaning carb it wouldn’t start. I did what u did and ding ding, started right up. However, when i plugged the solenoid wires back in, they started burning, melting and smoking. I unplugged solenoid and so far it starts and runs like before. I’m no mechanic, but I’m pretty sure the wires don’t need to be reconnected since that part now serves no purpose to the mower. Woohoo!!!!!
Thank you. I bought my mower 3 years ago and have already had this problem twice.
Sir, thank you very much!!! I did it exactly how you described and it worked...I was tired of throwing money at the problem. Thank you again.
I started the video as someone very skeptical but gave in and tried it. Shaved off the part just as you said. Turned the key and it started right up. Thank you very much for your help
DUDE
That fixed it.
I pulled the seat switch out.
I replaced the fuel filter.
I was looking up replacement parts for the entire fuel system.
My mechanic son found your video and forwarded it to me.
Mine was spinning.
Couldn't hear the click.
Pulled the part out, ground down the internal piece. Put it back together and it cranked right up.
Sweet.
Thanks for sharing.
Thanks John. I have the same mower and had the same problem. Saved me time and money!
You totally nailed it and saved me $$$ & time. It was the carburetor switch. THANK YOU!!!
Thank you Sir for your helpful information i have the same kind of lawnmower and the same problem with mine i did exactly what you said and it started rite up…… thanks 🤝
Have tried everything except this fix. Will try it tomorrow. Cant wait to see how it goes.
This is FYI ok? A mate who worked at a mechanic shop told me once how they fixed a very small 2 min fix problem on a womans car who left it at the shop for the day. It was a loose distributer lead causing a run rough situation. The mechanic listed a whole lot of BS fixes he said he did and charged her $700. I had a similar thing happen on my car brakes... but you cant argue with them while they hold your keys lol. So when the local mower man wanted me to deliver my Husqvana to his shop for a few days... I said forget it mate. haha.
Thank u. I know nothing about small engine. And I really impressed my wife and got lucky later that night. U the MAN !! She was using the mower when it shut off and was sick that she broke it. Thanks again. !!!
I want to thank you . I had the same problem. I installed a new fuel solenoid and it started on the first time.👍🙏👌
Great job!
You are the real MVP for this info! Thank you !
So well explained. Like many of the commenters I'd tried a LOT of things. Nothing was making sense. Thank You.
Thanks John. Easy to follow instructions. Will take a look at the filter as well. Mower is only 3 years old.
Legend!
Exact same “cause” scenario and fix worked a treat.
Mine died while I was mowing grass. I did as you showed and I am up and running. Thanks!!
Thanks for the tip !!! They told me it wasn’t bad at the husqvarna dealership…
Thanks so much. I am useless but i was able to do this quickly and it worked just like u said. My neighbors (and wife) are going to be shocked that i fixed it myself
Thats great! I think it's important we all know how to fix things on our own.
I have the same model mower and it shut off while I was mowing a couple weeks ago. Couldn't figure out what the problem was getting it to start. This worked on the first try! Thanks!
i also want you to know how much headache you saved me. Same problem and your fix was nothing short of brilliant. Thank you so much.
Hey Friend- I have the same mower and experienced the same problems. I followed you instructions and it worked perfectly! Thank you so much!
You're the best! Thank you! she running like a dream again!!
Great video...one exception comment. Bypassing your backup blade shutoff. I use to want to do that to my mower, unfortunately I work in an Emergency room and had a little baby girl that got run over by a mower that was backing up and ran over her leg. Really really bad scene, lost a limb and had to live with it because of that reason. I feel for the family because it was a total accident. No one knew the child was outside. I use to want to do that to my mower but now have to say there is hardly a time that I don't back up on my mower that I don't think about this child. My kids are grown and have no children but you never know. Could be a child, a pet or something. Not worth it.
Thank you sooo much..
I bought a new one since I was nervous about cutting one and it worked!!!!
Was able to do it by myself too!!!!
you go, girl!
My yth 18542 does not cut same on 4 l reach under deck and right blade spins around but left blade turns like it's in gear u can turn but tight right u can spin around can u help please
@@Tommy-m2f i had same problem,bushing were bad in the spindle,i took deck off,and replaced both spindles myself,put new blades while i was at it.I got a pair of new ones from Amazon for 43 dollars.Blades spin very easy now and QUIET,i replaced belt while i was at it.
I have never worked.on a mower,the hardet part was getting the old bolts out,4 botls in each spindle,i used a impact drill with a socket adapter and lots of bolt loosening spray.
Many videos on utube how to change spindles on this mower.
I fixed the fuel solenoid like you said.. Mower started right up. Thank you very much!!! :-)
Shot in the dark, but this worked. Thank you sir
Your welcome
Thank you for your helpful video. Fixxed my mower just as you said.
Thanks!!!! You saved me tons of time searching whats wrong...
Awesome video man! So glad I was able to find this. Solved my problem and got me mowing again! Thank you so much for making it!
Glad it helped. Mow on!
Fixed mine after checking all the obvious stuff. Thanks for this video!
Fixed mine. Thanks for the help!
You are THE Man!!!! Thank you so much!
Thank you my friend for sharing that video, that was a big help I was going a little crazy try to find the problem, found out a very small thin had to cut off and the lawnmower won’t start right up, your friend on the big Island of Hawaii thank you (aloha)
I have the same problem and the same exact mower. Tomorrow's payday but today will be perfect for mowing. I'm hoping that this will fix it! 🙏🏻🙏🏻🙏🏻 I'll edit if it works. I'm almost positive it will based on the comments.
It works, Let me know your experience.
@@Jsellers1965it didn't work. I've tried everything. I'm a mechanic that makes a fantastic living but my luck with anything that runs on gas just doesn't exist. I've no idea what is wrong with this POS!!
This is brilliant, thanks John!!! You are a life saver!!!
Thank you this fixed my mower.
Thank you. That's exactly what happened to me. I was cutting grass and it just died. Cut that pin off and was back in business!
THANK YOU! I did everything I could think of but it still wouldn't run. Tried to buy a new one, but nobody has any riding mowers under $4K. I will make it thru the summer now!
You fixed another one today.
Thank you.
Same thing to me today did what you said and worked like a dream thanks for the tip.
Took solenoid off, also checked electric to it, Yes to power but solenoid didn't function when reconnected and turned key on. Pretty sure (99%) that is my problem. Ordered new one from amazon $12.99 get it in 4 days. Thank you for the info. Lowes said they'd fix it but would take 4 weeks, have to ship it to Tampa 4 hours away. Suggested I take it to local husqvarna dealer for faster service, I called local dealer and they said since I didn't buy it at their store they will have to let it sit for 3 weeks B4 they would look at it. Gonna report them to Husqvarna and will tell Lowes (where I bought it) about the dealers B.S.
This Video Was Right On Point My Friend....Thank You So Much For Sharing....God Bless You.... 💯👍⭐️
Bought a new one and the click is VERY prominent. I don't know if the original is so loud but if it's not clicking it's absolutely the fuel solenoid.
Brother youbhave helped me a lot
I have the same lawnmower been having problems out of my every since I bought the thang thank you sir now my lawnmower won't turn over with the key I have to keep bumping the key to start it ughhh
Sorry to hear your troubles. My neighbors just started smoking and his is a year old and he paid $1k more than me from a dealer.
John I have a 2006 yth26hp and i have a problem with the mower starting after engaged deck, the pully on the left side if on the mower there's no belt on it and i tried loweing the deck to 1 so could check it out and wont go past or to 2nd like locked there, had deck check and they supposedly put new pulleys and belts last Spring but im not so sure they did, has like a clanking sound when engaging deck but now trys to start but will not turn over fully! Any suggestions?
Your blades might be bent
Good seeing ya out there big brother, and a "Mowing He will go"...LoL
Thanks Brother!
i just bought the husqvarna yth 21546 --- my problem is it wont start. I put fresh gas in it, charged the battery and the oil level is fine. It cranks good but just wont start? This thing is brand new and ive never been more frustrated. Is there some easy adjustment that can be made or should i return the mower??. In the troubleshooting manual-- it mentions fuel valve lever--- i didnt notice this.... wheres this at? engine is hv 703
Fuel valve should be right by the Carb or on the fuel line leading to it. It should be red. You might also have the same problem with the part in question in my video. It may be stuck closed. Your warranty would mean you would have to return the mower to where you bought it, in my case lowes, and they will send it out to be fixed. Or you might have to have a small engine shop look at it.
Will it click on half turn of key or when the ignition is engaged
If your talking about the solenoid I'm gonna guess when it's turned to run.
What if the lawnmower doesn’t have any compression? Any ideas on what to do?
Sounds like a valve or rings might need to be rebuilt
@@Jsellers1965
Ok. We checked the valves and they are working.
Did just what this video said and it fixed my problem. Thanks John. Saved me alot of money
You saved me money and a big headache. Thank you!
Any idea what this part is called or a part number for it so I can eventually replace it?
I'm glad I could help, They original part is expensive so I found a work around, knockoffs don't work so this is the fall back.
Appreciate you! Solved the problem.
Glad it helped.
My YTH has to crank and crank with the choke on, even on really hot days, before it will finally start. Wouldn't doubt if it's related to this "feature".
Mine has done this since new. Always had to use starting fluid. I'll check this tomorrow
Any luck? Mine needs starting fluid to start and I thought it might be the valves need adjusted. I haven't adjusted them yet.
@@moto-fl3rd Common problem on these is for the choke cable to be improperly set from the factory. Works for maybe the 1st season without any choke at all (even tho you think you are engaging it) because the motor is so brand-new perfect, but with normal wear needs real choke. 30-second fix. Loosen & readjust choke cable at that 1 screw that holds the middle of the choke cable to the side of the motor. Check at the end of the choke cable where it comes to the motor that the cable is actually pushing the lever as far forward as it can go... so the choke is really being engaged. No more starting fluid needed.
@@Grrrnthumb I'll give it a try. Thanks!
Darn it I will remember that. Thanks
Hi there I got a question for you for casually you know what's the camshaft number on my husqvarna 18.5 hp briggs and stratton intek engine I can't find the right number?
No I wouldn't know, it depends on the engine and you would have to look at the engine plate and look up what they put in that engine.
That mower is cool 😎 and thx
✋ Another happy owner. Thank you sir!
Solved our problem. Thanks so much!
John, I have a very similar Husqvarna, same issue it was having, STARVING FOR PETRO, I took the carb out, , I looked at every wrench I had, I had nothing that thin until I took a 12 mm wrench and grinded down until it fit in the area. I took off the bowl, I had seen no gas in the bowl, I CUT THAT DAM PIN OFF, put everthing together within the hour, AND IT RAN LIKE A CHAMP.. YOU CERTAINLY HELPED ME ON THIS ONE.. Years ago they never had those little gizmos, they just add more hedache..
THANK YOU AGAIN JOHN
Now I feel the deck shaking more than it should, do you have a remedy for this?..🙂
Temporary fix is put a magnet on the bottom of the solenoid. It pulls down the needle and lets the gas flow.
I tried several very strong magnets but no luck.
Bought 4 neodymium disc magnets at Menards for $17 and slapped them on the bottom. Mower hasn't ran this well for the past 2 years! Awesome advice!!!
Thanks! Saved me the other day!
@@jayholland4949 Thanks for the advise. I had just installed a new($10) fuel shut off solenoid. Worked great for the first mow after. Would not start a week later for the next mow. I tried the magnet, and it started right up! It must be a problem with the cheap solenoid. Maybe too tight. You saved me!
Thank you very much. It works again!
This worked like a charm. Thanks so much!
Mine had the same black dirt all over it. Spray it down with Mean Green Mildew. Looks brand new now.
Ever figure out what that black stuff was on your mower?
I figured it was mold but it will never come off.
Thank you! This is exactly what happened to me today!
Hey, I'm back! I can't get the Selenoid to come off! Can you give me some advice on that?
Thanks solenoid was the problem.
Your a legend man thanks :)
Happy to help
thanks a lot for sharing. tried everything else.❤
Did you put a cut off valve on the gas line? I did cut the pin off and it fixed the problem. My gas line have a cut off valve and apparently the valve is leaking cause I just put over a quart of none ethanol gas. The next day I have gas inside the engine oil and a flooded carburetor. So I am going to remove the line from the carburator and put some gas in tank and a container. If the container fill with gas. That means that cut off valve is defective.