Thankyou for posting this vid, I changed the wheel bearing on my superb today using this vid as a guide and it all went reasonably well. Can I suggest one thing for future vids, can you please post up a list of the tools needed, (i had to go through this vid taking notes of all the sockets/torx etc and having them listed would really have made it easier.)
You are absolutely right. All the main bolt connections must be tightened with a torque wrench. This video is considered to be an informative one, so it just shows the sequence of repairs. Best regards, Autodoc.
I have an issue with my Skoda superb mk2 at the moment. I put 4 new tyres on the car and noticed right away that it was pulling left. Got the alignment done and it still pulls to the left. The garage said it might be to do with a bad tyre. So I bought another tyre but now I don't know which tyre is the bad one. Any advice?
Thank you for the feedback! To give you an answer, we need to know more information about your car and its configuration. There will be no fundamental differences, however, some nuances may differ depending on the vehicle modification. Stay tuned and follow our latest updates. Best regards, Autodoc.
We cannot show all the nuances and problems during replacement since this is all individual and it is not always possible to solve them at home. To avoid this, we always recommend that replacements should be carried out by specialized car services.
In general, the replacement will be similar, the only thing that may be slightly different is the design features of your car. More accurate information can be found in the technical documentation of the car or by contacting a service center
Tisztelt Patrik Teljesen igazad van, minden időigényes munka, hogy időt takarítcsunk meg a videón minden elő van készítve. csavarokat be kell fújni sprayel, aminek állnia kell hogy könnyebben kijön a csavar. A következő videóban ezt is megemlítjük Tisztelettel AUTODOC csapat.
There is a mistake in our subtitles and we want to apologize for any inconvenience caused!
We used XZN socket bits instead of Torx socket bits.
Thank you for your understanding!
Yours truly, AUTODOC team.
Don't mind the nit pickers i think your videos are a great resource. Keep putting them out
Thank you for your comment! We really appreciate your positive feedback about our work, stay tuned for more! Best Regards, Autodoc Team.
Thankyou for posting this vid, I changed the wheel bearing on my superb today using this vid as a guide and it all went reasonably well. Can I suggest one thing for future vids, can you please post up a list of the tools needed, (i had to go through this vid taking notes of all the sockets/torx etc and having them listed would really have made it easier.)
In the new videos, we have already fixed this, we will be glad if you rate the new videos.
very informative is it easy to knock of the old one even on an older model
Nice video, very instructive. But where is the Torque Wrench?
You are absolutely right. All the main bolt connections must be tightened with a torque wrench. This video is considered to be an informative one, so it just shows the sequence of repairs. Best regards, Autodoc.
Just AGADAGADAGADAGDAGDGAGDGAGDAGDADAGA the shit out of it hahaha
I have an issue with my Skoda superb mk2 at the moment. I put 4 new tyres on the car and noticed right away that it was pulling left. Got the alignment done and it still pulls to the left. The garage said it might be to do with a bad tyre. So I bought another tyre but now I don't know which tyre is the bad one. Any advice?
So the skoda bearing is easier to replace than an a5? Typical
very helpful video ;)
Do you need to do tracking after replacing the wheel bearing?
Yes, it is recommended to adjust the wheel alignment after this replacement.
Do you know why some hub bearing carrier has 3 mounting bolts and some have 4? So there is no need to remove the ball joint for access?
We do not have such information, we recommend that you consult your mechanic.
Dobry den, na praci s demontazi/montazi loziska neni potreba stahovak a pripravek pro nalisovani? Dekuji.
Ano, je třeba použít stahovak a pripravek.
Nice video m8. Do you know if the Mk2 seat Leon is the same and don't need a press as it is whole hub. Thanks m8.
Thank you for the feedback! To give you an answer, we need to know more information about your car and its configuration. There will be no fundamental differences, however, some nuances may differ depending on the vehicle modification. Stay tuned and follow our latest updates. Best regards, Autodoc.
Does anyone know what the torque settings are pleas4
is it as easy to knock the old one off even on an older model
We cannot show all the nuances and problems during replacement since this is all individual and it is not always possible to solve them at home. To avoid this, we always recommend that replacements should be carried out by specialized car services.
Does this go with this car ? Škoda Superb Kombi 2.0 TDI 4x4 DSG Sekventiell, 170hk, 2014
In general, the replacement will be similar, the only thing that may be slightly different is the design features of your car. More accurate information can be found in the technical documentation of the car or by contacting a service center
Can you make the videos in future without that music please.
Tanks 👌👌
Thank you for the feedback! We are glad you find our video interesting and informative. Stay tuned. Best regards, Autodoc.
Why hasn’t the mechanic torqued the hub nut? That’s only hand tightened. How so ???
Shouldn't you use a press to push the new bearing into place? Why have you used new spline bolts and not reused the old ones?
Because they are single use.
No because the bearings in this instance come pressed into there housing already, you are changing the housing with the bearing already fitted.
And I foolishly tighten the screws with a torque spanner....
Elhiszem hogy ilyen egyszerű de lègkulcsal nem lazulnak a kerèkcsapágy 4 csavarja,nemhogy mèg hosszúszárral,😅😅😅
Tisztelt Patrik
Teljesen igazad van, minden időigényes munka, hogy időt takarítcsunk meg a videón minden elő van készítve.
csavarokat be kell fújni sprayel, aminek állnia kell hogy könnyebben kijön a csavar. A következő videóban ezt is megemlítjük
Tisztelettel AUTODOC csapat.