I have them on my ham radio site here at this address.........pixiekits.com/electronickits/p/ge-interlogix-atp-hardwired-alphanumeric-programming-alarm-keypad
How do you change an sensor in programming that says NC but is a motion so should be NO same for my Fire Alarm says NC in programming but need to change to NO?
The NC is software generated, as long as you have the Group # correct you can wire your zones open or closed. The NC in programming has no significance in the wiring of the zone. Just be sure that the EOL resistor on a NO circuit is across the loop and an NC is wired in Parallel
Do you happen to know the part number for the alpha programing keypad without the door cover ? Maybe I can fine it on Amazon. I know nobody makes these parts anymore.
Do the wireless sensor numbers have to start at 9 even if you don't have any wired sensors connected to the panel? I haven't been able to find that stated in the Concord Express documentation. Note that I'm interested in the Express not the 4.
Almost the same process to add 1,,,,go to the section where it says SENSORS the scroll up or down to DELETE SENSOR ,,,delte the bad sensor tnen * back to learn sensor and then learn in the new sensor
Does the alphanumeric programming touchpad need to be connecting directly to the panel board via a special cable? or can it just be wired into the bus connection? thanks
It can be wired as a normal keypad.. but after you get done programming you will need to go into bus devices and delete it from the program or when you get done programming about 10 minutes after the panel will go into trouble looking for that keypad
The restoral is the report that will be sent by the alarm panel when the panel is reset from an alarm event or when the panel times out,,, usually, around 9-15 minutes after the alarm occurs. Supervisory is when a zone has a low battery,, the panel has low battery, basically sends a report when something is wrong with the system. CS is short for Central Station,,, is set in the panel if the panel is set to report a code to the Central Station if an alarm event occurs.
Thanks for reply. I researched and apparently the default is 9713 on my device. However when I use *8, enter code, then it asks for device address. Going to have to research more. I removed and replaced a door that had a wireless programmed in, trashed it. Now keypad is angry beeping lol. Trying to find out how to remove it. Anyhow thanks for the vid
Good video.. only problem is: you talk too much. You do more talking than you do teaching. This was a 10 minute video. Everything you taught could have been done in 4 minutes time. Good video though.
![Jim Stickley Demonstrates How to Bypass Home Alarms [TV]](http://i.ytimg.com/vi/6bRWJVul2yM/mqdefault.jpg)
Thank you very much for making the video.
This was very helpful. Thanks for taking the time to do this video.
God Bless U
Great video and demonstration! Thank You! 💪🏾💪🏾🔥
The sound is weard
When I get to the command where I enter 00...It does a different beep and puts me back at the main menu. Im trying to replace a faulty sensor
Where can I purchase the keypad that will allow programming to replace one that is not capable?
I have them on my ham radio site here at this address.........pixiekits.com/electronickits/p/ge-interlogix-atp-hardwired-alphanumeric-programming-alarm-keypad
How do you change an sensor in programming that says NC but is a motion so should be NO same for my Fire Alarm says NC in programming but need to change to NO?
The NC is software generated, as long as you have the Group # correct you can wire your zones open or closed. The NC in programming has no significance in the wiring of the zone. Just be sure that the EOL resistor on a NO circuit is across the loop and an NC is wired in Parallel
Do you happen to know the part number for the alpha programing keypad without the door cover ?
Maybe I can fine it on Amazon. I know nobody makes these parts anymore.
eBay has some
Do the wireless sensor numbers have to start at 9 even if you don't have any wired sensors connected to the panel? I haven't been able to find that stated in the Concord Express documentation. Note that I'm interested in the Express not the 4.
Yes they must start at 9, There are other panels that can use up the unused hardwire zones as wireless zones but not the Concord Series of panels
I think if you have an end of line resistor on one of the 1-8s You can use a Wireless sensor on there.
One of my sensors messed up. I want to replace it. How do I delete the broken/older sensor so I can install the new one?
Almost the same process to add 1,,,,go to the section where it says SENSORS the scroll up or down to DELETE SENSOR ,,,delte the bad sensor tnen * back to learn sensor and then learn in the new sensor
@@DIYELEKTRONICKITS thanks. What's your email? I have a few more questions. Thanks!
@@xpectz pixiekits@gmail
Does the alphanumeric programming touchpad need to be connecting directly to the panel board via a special cable? or can it just be wired into the bus connection? thanks
It can be wired as a normal keypad.. but after you get done programming you will need to go into bus devices and delete it from the program or when you get done programming about 10 minutes after the panel will go into trouble looking for that keypad
@@DIYELEKTRONICKITS great thank you for the information
In the Group descriptions what does Restoral, Supervisory and CS Report....refer to? Thanks
The restoral is the report that will be sent by the alarm panel when the panel is reset from an alarm event or when the panel times out,,, usually, around 9-15 minutes after the alarm occurs.
Supervisory is when a zone has a low battery,, the panel has low battery, basically sends a report when something is wrong with the system.
CS is short for Central Station,,, is set in the panel if the panel is set to report a code to the Central Station if an alarm event occurs.
@@DIYELEKTRONICKITS Thank you very much, I'm assuming the CS is the alarm company?
@@bkoz319 yes
Thanks!
Thanks for this
How do you replace wireless smoke detectors??
my concord system only allows up to 24 sensors is it possible to expand this?
You can expand it with hardwire zones only,,,, not wireless.
24 zones wireless is MAX for a Concord Express
@@DIYELEKTRONICKITS ok thanks for the information. great videos. you are an excellent resource
In what Group Number would you program Garage door tilt sensors in?
13 instant
Informative. However, NASA has better comms from the space station.
thank you !
what model of keypad are you using?
60-983 ATP1000
how to find the installer code? thank you!
ruclips.net/video/kIKiwDCdF00/видео.html&ab_channel=G-GElectronics
What if my system is 10 years old and I don't know the installer code?
You will need to send me your chip to be read and I can get the code for you.
Thanks for reply. I researched and apparently the default is 9713 on my device. However when I use *8, enter code, then it asks for device address. Going to have to research more. I removed and replaced a door that had a wireless programmed in, trashed it. Now keypad is angry beeping lol. Trying to find out how to remove it. Anyhow thanks for the vid
Nx 8v2 btw
Nx 8v2 btw
@@AlteredComponent Try.....4321.....6321
Good video.. only problem is: you talk too much. You do more talking than you do teaching.
This was a 10 minute video. Everything you taught could have been done in 4 minutes time.
Good video though.
You have to understand that this is geared toward the home owner,,,but I do get your point and do try to keep them short and too the point
@@DIYELEKTRONICKITS ... Yeah, you were right, I was wrong. Good video.
Thank you again.
@@DIYELEKTRONICKITSexactly. thanks