How to do wireless enrollment for the Interlogix NetworX Tutorial
HTML-код
- Опубликовано: 10 сен 2024
- Jason of Alarm System Store takes you through another DIY tutorial on how to enroll Interlogix wireless devices on the Interlogix NetworX series of alarm systems.
Interlogix NetworX panels can accommodate Interlogix wireless devices by adding the NX584E wireless receiver or a hardwired keypad with built-in wireless receiver such as the NX148ERF. The amount of wireless devices that a NetworX panel can handle very depending on model. The Interlogix wireless devices have a placement range of up to a 1000' radius out from the receiver.
The Interlogix NetworX panels are a line of alarm control panels that will give you the ability to wire in hardwired devices or use Interlogix wireless detection devices by adding the NX548E 48 zone wireless receiver.
The NetworX NX4 can handle up to 8 zones with 4 onboard and up to 8 user codes. The NetworX NX6 can handle up to 16 zones with 6 onboard and the rest can be had with zone expanders or wireless receivers. And finally, the NetworX NX8 can handle up to 48 zones with 8 onboard and more to be had by adding zone expanders or a wireless receiver.
You can check out all of the kits that we offer in the Interlogix NetworX series by visiting this link - www.alarmsyste...
Please comment in the comments section if you have any questions and be sure to slap that like button and subscribe to our channel for all of our how to videos for some of today's most popular DIY security systems.
You can also visit our website at alarmsystemstor... for all of our great deals on security equipment.
You can also follow us on the following social sites for information, coupon codes, and much more!
Facebook - / alarmsystemstore
Twitter - / alarmstore
Google+ - plus.google.com...
How do you change/replace a wireless device on the same panel ?
How do you delete a zone?
How do you delete devicesm
How do you replace a sensor? Just enroll like you are adding a new one?
I am looking to replace a wireless sensor (nx-8v2) do you need to remove the old one first and how would you do that?
How do you access zones 100+ in wireless programming delete and add contacts?
I'm looking for instructions for enrollment of sensors on my networx nx-6 using my LED keypad (nx-1324). Do you have a video for this, or can you explain how I can use this video for my keypad?
If we have more than one panel, do we have to pair the sensor with the closet panel, or the main one?
Do you get to choose whether it’s perimeter or entry/exit? Is it the same for a motion detector, glassbreak, or a smoke detector?
How do you replace smoke sensors with new ones??
That's a Concord 4 keypad, correct? Also - these are Z-wave devices you are adding? And finally, does the keypad act as a Z-wave repeater? Thanks for the great videos and pardon my confusion
The keypad is an NX148ERF and it's being used on a Interlogix NetworX panel. The keypad can talk with Interlogix wireless devices which are the devices being used here. They're not Z-Wave. The keypad has no Z-Wave controllers or repeaters in it. It only communicates on the Interlogix wireless frequency. Thanks for watching!
Thanks for the info and your amazing channel. Do any of the newer keypads act as Z-Wave repeaters and does the keypad care if there are hybrid sensors (wired and wireless) and finally is there a keypad where the sensors can be defined and labeled easily - i.e. "Sensor 54" is irrelevant to me and with the NX148ERF I think renaming the sensors is a PIA - espeically if you have multiple keypads. Thanks again
Programming the DMP XT series security panel for wireless devices is much more complicated as its shown on RUclips
Depending on the wireless receiver module the location code may be different! I have an NX-408 wireless receiver, which uses 49# to enroll new wireless sensors - not to be confused with the NX-408E that does indeed use 0# like the video. How to tell which one you have got if you just moved house and don't have a programming module? NFI >_
Mate, I've been trying to enrol new sensors for hours, and you just saved me. Legend 👍
Does anyone know where can I get the software for programming?
Following these steps, but the device doesn’t show up in the zone list
I would definitely also check out our programming guide for this system which can be found here - www.alarmsystemstore.com/pages/interlogix-networx-nx4-nx6-nx8-nx8e-quickstart
How do you change device description
where is the device address, on the panel?
You can find a list of device addresses in the Interlogix installation manual. Device 0 is the main panel programming address.
How do u program zone label?
Is there any Panel replace the NX-8 ?
I recommend DSC Neo. Very good hybrid system.
Nx8 has to be the worst fucking system made so glad it’s discontinued
How do you delete a wireless zone?