Step-by-Step: Restoring Rusty Door with Power Hammer and Profile Dies | '29 Roadster
HTML-код
- Опубликовано: 24 июн 2023
- On this episode we take step in where Karl finished in order to finalise the lower repair section of the damaged inner door structure. We learn to use the Power Hammer and get this closer to mating with the outer door skin. Enjoy!
Join this channel to get access to perks:
/ @bennettscustomsco
Shop ➡️ www.bennettscustomsco.com.au/...
Instagram ➡️ bennettscus... Авто/Мото
Nice save on the door! Looking forward to next video!
Looking good! I laughed watching you reposition for welding , I do that all the time! You gotta get comfortable! I'm looking forward to the split window project as well.
Hey Jordan, great job on the door repair! Karl's die really made the forming turn out perfect! I really like the way you teach us as you're learning, too. And your comments about what you could do better next time really work for me. Thanks a bunch!
Great improvisation. For a first timer on your new equipment you looked like a pro. Good job.
Nice job saving a door that was almost scrap yard ready.
The door is coming along nicely Jordan, the more I see the power hammer working the more I like... I might have to build one of Karl's pov versions, good content again and the splitty work sounds interesting. cheers Greg
Yeah, nice teaser. Please do show all the details on the bus mod! 😎
Great video buddy!
Nice job Jordan looks great
Carl it's coming along nicely so far sir. Can't wait to see more videos soon my friends. Keep up the great craftsmanship and hard work my friends. Fab On. Weld On. Keep Making. God bless.
One of My favorita RUclips channels!
John great video per your usual
You are great!
My late father had a term for your friend. He would call him a seagull, eat,shits and squawk's. Coming from the Pacific northwest you understand.
Have you considered using electrolysis or citric acid for rust removal, they both get into EVERY area and work extremely well, I even add Citric acid to my electrolysis tank to speed up the process, adding heat also speeds up the process. Do not use it on Cast Iron or Aluminium. Just pressure wash and admire the results. Molasses also works well but the smell upsets the wife so I do not use it anymore. Granular Citric Acid is usually available from rural supply outlets, they use it in wineries to clean out their pipes. Cost about $120 to $150 for 20kg, use about a 1/2 cup per gallon / 5 litres
Yes it can take a couple of days but definitely worth it.
Electrolysis is cheaper, just run it off a battery charger, I use stainless for my sacrificial anode as it seems to last longer but any conductor will work.
Also use the hand wheel under your power hammer bottom anvil to adjust the clearance rather than adjusting the collet, much easier and infinite control, just back off the securing screws and wind it up or down, don't forget to tighten the screws back up.
Good video question how did you remove the outer door skin from the inner frame without damaging the lip . i had seen guys using special vice grip pliers getting under neath the lip and also making new lips and tig welding them back on , Thanks
Bravo bravo bravo
Nice Work. I'm behind on my Videos.
#STAYSAFE
#PHILLYPHILLY 🇺🇸
Nice videos!
What weld thru primer do you use? Seems they get rusty after a while
Thanks
I don’t usually use weld through primer when I’m tig welding.
What's the 90 degree pneumatic sander you're using?
Cheers 🙂
he, what amp do you run while welding tins for you roadster ? point and lines,@flat and @angle ? thx
"Promosm"
Jesus
The Race Where??? 🫢
🦘🇦🇺 🤔mmm, did I spy a fibreglass sidecar body up on the loft ?